Page 1
SX
120
SX-RELAYS
HIGH SENSITIVITY RELA Y
WITH GUARANTEED LOW
LEVEL SWITCHING
CAPACITY
7.4
.291
15.0
.591
8.2
.323
mm inch
7.4
.291
15.0
.591
Max. 10.0
.394
FEATURES
1. High contact reliability over a long
life has been made possible for low
level loads.
Using a low level load (1 mV 10 µ A to 10 V
10 mA) 10
7
operations were achiev ed with
a static contact resistance of Max. 100
m Ω (voltage drop of 20 mV, 1 mA, 1 kHz)
and a dynamic contact resistance of Max.
1 Ω (Measurement delay 10 ms, voltage
drop of 20 mV, 1 mA, 1 kHz).
2. High sensitibity of 50 mW
By using the highly efficient polar magnetic circuit "seesaw balance armature
mechanism", a rated power consumption
of 50 mW (for single side stable type) has
been achieved.
3. Low thermal electromotive force
Reducing the heat from the coil enables a
thermal electromotive force of 3 µ V or
less.
SPECIFICATIONS
Contact
Notes:
**
1
This value can change due to the switching frequency , environmental conditions ,
and desired reliability level, therefore it is recommended to chec k this with the actual load.
**
2
For single side stable only.
Characteristics
Remarks:
* Specifications will vary with foreign standards certification ratings.
*
1
By nominal switching capacity: No. of operations: 10
7
*
2
Measurement at same location as "Initial breakdown voltage" section.
*
3
Detection current: 10mA.
*
4
Nominal voltage applied to the coil, excluding contact bounce time.
*
5
By resistive method, nominal voltage applied to the coil; contact carrying current:
10mA.
*
6
Half-wave pulse of sine wave: 6 ms; detection time: 10 µ s.
*
7
Half-wave pulse of sine wave: 6 ms.
*
8
Detection time: 10 µ s.
*
9
Refer to 5. Conditions for operation, transpor t and storage mentioned in
AMBIENT ENVIRONMENT (Page 61)
Arrangement 2 Form C
Static contact resistance (During initial and
electric life tests)*
1
(By voltage drop of 20 mV 1 mA [1kHz])
Max. 100 m Ω
Dynamic contact resistance (During initial and
electric life tests)*
1
(By voltage drop of 20 mV 1 mA[1 kHz], Measurement delay 10 ms after applying nominal
coil voltage)
Max. 1 Ω
Contact material Gold-clad silver alloy
Rating
Nominal switching capacity
(resistive load)
10 mA 10 VDC
Max. switching power 0.1 W
Max. switching voltage 10 VDC
Max. switching current 10 mA DC
Min. switching capacity**
1
10 µ A 1 mVDC
Nominal
operating
power
Single side stable
50mW (1.5 to 12 V DC)
70mW (24 V DC)
1 coil latching
35mW (1.5 to 12 V DC)
50mW (24 V DC)
2 coil latching
70mW (1.5 to 12 V DC)
150mW (24 V DC)
Thermal electromotive force, max.
(at nominal voltage applied to the coil**
2
)
3 µ V
Expected
life (min.
operations)
Mechanical (at 750 cpm) 5 × 10
7
Electrical (at 750 cpm)
(10 mA 10 V DC resistive load)
10
7
Initial insulation resistance*
2
Min. 10,000M Ω
(at 500V DC)
Initial
breakdown
voltage*
3
Between open contacts 750 Vrms for 1min.
Between contact sets 1,000 Vrms for 1min.
Between contact and coil 1,800 Vrms for 1min.
Operate time [Set time]*
4
(at 20 ° C)
Max. 5 ms (Approx. 3 ms)
[Max. 5 ms (Approx. 3 ms)]
Release time (without diode)
[Reset time]*
4
(at 20 ° C)
Max. 5 ms (Appro x. 1.5 ms)
[Max. 5 ms (Approx. 3 ms)]
Temperature rise*
5
(at 20 ° C) Max. 50 ° C
Shock resistance
Functional*
6
Min. 750 m/s
2
{75G]
Destructive*
7
Min. 1,000 m/s
2
{100G]
Vibration resistance
Functional*
8
10 to 55 Hz at double
amplitude of 3.3 mm
Destructive
10 to 55 Hz at double
amplitude of 5 mm
Conditions for operation,
transport and storage*
9
(Not freezing and condensing at low temperature)
Ambient
temperature
–40 ° C to 70 ° C
–40 ° F to 158 ° F
Humidity 5 to 85% R.H.
Unit weight Approx. 2 g .071 oz
TYPICAL APPLICATIONS
This relay will be used for the small load
for measuring instruments or others
where a stable contact resistance is
required.
TESTING
Page 2
SX
121
ORDERING INFORMATION
200A Z1HEx. ASX
Contact arrangement
Terminal shapeOperating function Packing style
Coil voltage (DC)
Nil: Standard PC board terminal
A: Surface-mount terminal
2: 2 Form C 0: Single side stable
1: 1 coil latching
2: 2 coil latching
Type of operation
0: Standard type
(B.B.M.)
Nil: Tube packing
Z:
Tape and reel packing
(piked from 8/9/10/12
pin side)
1H: 1.5V
03 : 3V
4H: 4.5V
06 : 6V
09 : 9V
12 : 12V
24 : 24V
Note: Tape and reel packing symbol “-Z” is not marked on the relay. “X” type tape and reel packing (picked from 1/3/4/5-pin side) is also available. Suffix “X” instead of “Z”.
TYPES AND COIL DATA (at 20 ° C 68 ° F)
(1) Standard PC board terminal
1) Standard packing: 40 pcs. in an inner package (tube); 1,000 pcs. in an outer package
2) Specified value of pick-up, drop-out, set and reset voltage is with the condition of square wave coil pulse.
Single side stable
1 coil latching
2 coil latching
Part No.
Coil Rating,
V DC
Pick-up voltage,
V DC (max.)
(initial)
Drop-out
voltage,
V DC (min.)
(initial)
Nominal
operating current,
mA ( ± 10%)
Coil resistance,
Ω ( ±
10%)
Nominal
operating power,
mW
Max. allowable
voltage,
V DC
Standard PC
board terminal
ASX2001H 1.5 1.2 0.15 33.3 45 50 2.25
ASX20003 3 2.4 0.3 16.7 180 50 4.5
ASX2004H 4.5 3.6 0.45 11.1 405 50 6.75
ASX20006 6 4.8 0.6 8.3 720 50 9
ASX20009 9 7.2 0.9 5.6 1,620 50 13.5
ASX20012 12 9.6 1.2 4.2 2,880 50 18
ASX20024 24 19.2 2.4 2.9 8,229 70 36
Part No.
Coil Rating,
V DC
Set voltage,
V DC (max.)
(initial)
Reset voltage,
V DC (max.)
(initial)
Nominal
operating current,
mA ( ± 10%)
Coil resistance,
Ω ( ±
10%)
Nominal
operating power,
mW
Max. allowable
voltage,
V DC
Standard PC
board terminal
ASX2101H 1.5 1.2 1.2 23.3 64.3 35 2.25
ASX21003 3 2.4 2.4 11.7 257 35 4.5
ASX2104H 4.5 3.6 3.6 7.8 579 35 6.75
ASX21006 6 4.8 4.8 5.8 1,029 35 9
ASX21009 9 7.2 7.2 3.9 2,314 35 13.5
ASX21012 12 9.6 9.6 2.9 4,114 35 18
ASX21024 24 19.2 19.2 2.1 11,520 50 36
Part No.
Coil Rating,
V DC
Set voltage,
V DC (max.)
(initial)
Reset voltage,
V DC (max.)
(initial)
Nominal
operating current,
mA ( ± 10%)
Coil resistance,
Ω ( ±
10%)
Nominal
operating power,
mW
Max. allowable
voltage, V DC
Standard PC
board terminal
Set coil
Reset
coil
Set coil
Reset
coil
Set coil
Reset
coil
ASX2201H 1.5 1.2 1.2 46.7 46.7 32.1 32.1 70 70 2.25
ASX22003 3 2.4 2.4 23.3 23.3 129 129 70 70 4.5
ASX2204H 4.5 3.6 3.6 15.6 15.6 289 289 70 70 6.75
ASX22006 6 4.8 4.8 11.7 11.7 514 514 70 70 9
ASX22009 9 7.2 7.2 7.8 7.8 1,157 1,157 70 70 13.5
ASX22012 12 9.6 9.6 5.8 5.8 2,057 2,057 70 70 18
ASX22024 24 19.2 19.2 6.3 6.3 3,840 3,840 150 150 36
Page 3
SX
122
(2) Surface-mount terminal
1) Standard packing: 40 pcs .(tube), 1,000pcs . (tape and reel)in an inner package; 500 pcs.(tube), 1,000pcs. (tape and reel)in an outer
package
2) Specified value of pick-up, drop-out, set and reset voltage is with the condition of square wave coil pulse.
Single side stable
1 coil latching type
2 coil latching type
Part No.
Coil Rating,
V DC
Pick-up
voltage,
V DC (max.)
(initial)
Drop-out
voltage,
V DC (min.)
(initial)
Nominal
operating
current,
mA ( ± 10%)
Coil resistance,
Ω ( ±
10%)
Nominal
operating
power,
mW
Max.
allowable
voltage,
V DC
Tube packing
Tape and reel
packing
ASX200A1H ASX200A1HZ 1.5 1.2 0.15 33.3 45 50 2.25
ASX200A03 ASX200A03Z 3 2.4 0.3 16.7 180 50 4.5
ASX200A4H ASX200A4HZ 4.5 3.6 0.45 11.1 405 50 6.75
ASX200A06 ASX200A06Z 6 4.8 0.6 8.3 720 50 9
ASX200A09 ASX200A09Z 9 7.2 0.9 5.6 1,620 50 13.5
ASX200A12 ASX200A12Z 12 9.6 1.2 4.2 2,880 50 18
ASX200A24 ASX200A24Z 24 19.2 2.4 2.9 8,229 70 36
Part No.
Coil Rating,
V DC
Set voltage,
V DC (max.)
(initial)
Reset
voltage,
V DC (max.)
(initial)
Nominal
operating
current,
mA ( ± 10%)
Coil resistance,
Ω ( ±
10%)
Nominal
operating
power,
mW
Max.
allowable
voltage,
V DC
Tube packing
Tape and reel
packing
ASX210A1H ASX210A1HZ 1.5 1.2 1.2 23.3 64.3 35 2.25
ASX210A03 ASX210A03Z 3 2.4 2.4 11.7 257 35 4.5
ASX210A4H ASX210A4HZ 4.5 3.6 3.6 7.8 579 35 6.75
ASX210A06 ASX210A06Z 6 4.8 4.8 5.8 1,029 35 9
ASX210A09 ASX210A09Z 9 7.2 7.2 3.9 2,314 35 13.5
ASX210A12 ASX210A12Z 12 9.6 9.6 2.9 4,114 35 18
ASX210A24 ASX210A24Z 24 19.2 19.2 2.1 11,520 50 36
Part No.
Coil Rating,
V DC
Set voltage,
V DC (max.)
(initial)
Reset
voltage,
V DC (max.)
(initial)
Nominal
operating
current,
mA ( ± 10%)
Coil resistance,
Ω ( ±
10%)
Nominal
operating
power,
mW
Max.
allowable
voltage,
V DC
Tube packing
Tape and reel
packing
Set
coil
Reset
coil
Set
coil
Reset
coil
Set
coil
Reset
coil
ASX220A1H ASX220A1HZ 1.5 1.2 1.2 46.7 46.7 32.1 32.1 70 70 2.25
ASX220A03 ASX220A03Z 3 2.4 2.4 23.3 23.3 129 129 70 70 4.5
ASX220A4H ASX220A4HZ 4.5 3.6 3.6 15.6 15.6 289 289 70 70 6.75
ASX220A06 ASX220A06Z 6 4.8 4.8 11.7 11.7 514 514 70 70 9
ASX220A09 ASX220A09Z 9 7.2 7.2 7.8 7.8 1,157 1,157 70 70 13.5
ASX220A12 ASX220A12Z 12 9.6 9.6 5.8 5.8 2,057 2,057 70 70 18
ASX220A24 ASX220A24Z 24 19.2 19.2 6.3 6.3 3,840 3,840 150 150 36
DIMENSIONS
1. PC board terminal
Single side stable/
1 coil latching
0.5
.020
1.15
.045
2.54
.100
3.5
.138
0.65
.026
5.08
.200
0.25
.010
15.0
.591
5.08
.200
8.2
.323
7.4
.291
mm inch
2 coil latching
0.5
.020
1.15
.045
2.54
.100
3.5
.138
0.65
.026
5.08
.200
0.25
.010
15.0
.591
5.08
.200
8.2
.323
7.4
.291
General tolerance: ± 0.3 ± .012
PC board pattern
5.08
.200
2.54
.100
8-1.0 dia.
8-.039 dia.
10.16
.400
5.08
.200
2.54
.100
10-1.0 dia.
10-.039 dia.
12.7
.500
Tolerance: ± 0.1 ± .004
Schematic (Bottom view)
Single side stable
(Deenergized condition)
1 coil latching
(Reset condition)
Direction indication
12 10 9 8
1 3 4 5
Direction indication
12 10 9 8
1 3 4 5
2 coil latching
(Reset condition)
Direction indication
12 10 9 8 7
1 3 4 5 6
Page 4
SX
123
2. Surface-mount terminal
Single side stable/
1 coil latching
5.08
.200
5.08
.200
2.54
.100
0.65
.026
9.4±0.5
.370±.020
15.0
.591
0.5
.020
8.2
.323
7.4
.291
Max.10.0
.394
0.25
.010
1.15
.045
mm inch
2 coil latching
5.08
.200
5.08
.200
2.54
.100
0.65
.026
0.25
.010
9.4±0.5
.370±.020
0.5
.020
8.2
.323
15.0
.591
Max.10.0
.394
7.4
.291
1.15
.045
General tolerance: ± 0.3 ± .012
Suggested
mounting pad
5.08
.200
1.0
.039
2.54
.100
3.16
.124
7.24
.285
5.08
.200
1.0
.039
2.54
.100
3.16
.124
7.24
.285
,,
,,
,,
,
Tolerance: ± 0.1 ± .004
Schematic (Top view)
Single side stable
(Deenergized condition)
1 coil latching
(Reset condition)
Direction indication
12 10 9 8
1 3 4 5
Direction indication
12 10 9 8
1 3 4 5
2 coil latching
(Reset condition)
Direction indication
12 10 9 8 7
1 3 4 5 6
REFERENCE DATA
1. Switching capacity range 2-(1). Change in dynamic contact resistance
(10 mA 10 V DC resistive load)
Tested: ASX20012, Quantity: n=10
Operating frequency: 750 cpm
Measured condition: 10 ms after applying nominal coil
voltage, using voltage drop of 20 mV, 1 mA, 1 kHz.
2-(2). Change in dynamic contact resistance
(10 µ A 1 mV DC resistive load)
Tested: ASX20012, Quantity: n=10
Operating frequency: 750 cpm
Measured condition: 10 ms after applying nominal coil
voltage, using voltage drop of 20 mV, 1 mA, 1 kHz.
10mA
10µA
1mV
10V
Contact voltage
Contact current
1,0000
Min.
0
0.1
0.2
0.3
0.4
0.5
0.6
0.7
0.8
0.9
1.0
Max.
No. of operations, × 10
4
Contact resistance, Ω
2,0001,0000
Min.
0
0.1
0.2
0.3
0.4
0.5
0.6
0.7
0.8
0.9
1.0
Max.
No. of operations, × 10
4
Contact resistance, Ω
3-(1). Change in static contact resistance
(10 mA 10 V DC resistive load)
Tested: ASX20012, Quantity: n=10
Operating frequency: 750 cpm
3-(2). Change in static contact resistance
(10 µ A 1 mVDC resistive load)
Tested: ASX20012, Quantity: n=10
Operating frequency: 750 cpm
1,000
0
10
20
30
40
50
60
70
80
90
0
Max.
Min.
Max.
Min.
0
10
20
30
40
50
60
80
90
100
No. of operations, × 10
4
Contact resistance, mΩ
N.C. side contact
N.O. side contact
2,0001,000
0
10
20
30
40
50
60
70
80
90
0
Max.
Min.
Max.
Min.
0
10
20
30
40
50
60
80
90
100
No. of operations, × 10
4
Contact resistance, mΩ
N.C. side contact
N.O. side contact
Page 5
SX
124
NOTES
1. Coil operating power
1) As a general rule, only a pure DC power supply should be used for the coil drive.
2) To ensure proper operation, the voltage
applied to both terminals of the coil should
be ±5% (at 20°C 68°F) the rated operating
voltage of the coil. Also , be aware that the
pick-up and drop-out voltages will fluctuate depending on the ambient temperature and operating conditions.
3) The ripple factor f or the voltage applied
to the coil should be less than 5%.
4) For set and reset latching relays, the
rated operating voltage should be applied
to the coil for 10 ms or more.
2. Coil connection
When connecting coils, refer to the wiring
diagram to prevent mis-operation or malfunction.
3. External magnetic field
Since SX relays are highly sensitive polarized relays, their characteristics will be affected by a strong e xternal magnetic field.
Avoid using the rela y under that condition.
4. Cleaning
In automatic cleaning, cleaning with the
boiling method is recommended. A v oid ultrasonic cleaning which subject the relay
to high frequency vibrations. It may cause
the contacts to stick.
lt is recommended that a fluorinated hydrocarbon or other alcoholic solvent be
used.
5. Packing style
1) The relay is packed in a tube with the
relay orientation mark on the left side, as
shown in the figure below.
2) Tape and reel packing
(1) T ape dimensions
mm inch
(2) Dimensions of plastic reel
mm inch
6. Automatic insertion
To maintain the internal function of the relay, the chucking pressure should not exceed the values below.
Chucking pressure in the direction A:
4.9 N {500 gf} or less
Chucking pressure in the direction B:
9.8 N {1 kgf} or less
Chucking pressure in the direction C:
9.8 N {1 kgf} or less
Please chuck the portion.
Avoid chucking the center of the relay.
In addition, excessive chucking pressure
to the pinpoint of the relay should be also
avoided.
Orientation (indicates PIN No.1)stripe
Stopper (gray) Stopper (green)
SX relays
Relay polarity bar
(Z type)
Tape coming out direction
General tolerance ±0.1 mm .004 inch
4.0±0.1
.157±.004
1.75±0.1
.069±.004
2.0±0.1
.079±.004
0.40±0.1
.016±.004
10.8±0.2
.425±.008
16.0±0.1
.630±.004
10.0±0.1
.394±.004
1.50 dia.
.059 dia.
+0.1
0
+.003
.0
11.5±0.1
.453±.004
15.5±0.1
.610±.004
Max. 20.0
.787
24.0±0.3
.945±.012
21±0.8 dia.
.827±.031 dia.
13±0.2 dia.
.512±.008 dia.
24.4
.961
+2
0
+.079
0
100±1 dia.
3.937±.039 dia.
2.0±0.2
.079±.008
370±2 dia.
14.567±.079 dia.
2.0±0.5
.079±.020
A
C
B
For Cautions for Use, see Relay Technical Information (Page 48 to 76).
9/1/2000 All Rights Reserved, © Copyright Matsushita Electric Works, Ltd.
Go To Online Catalog
Loading...