Datasheet ASM3P2769A Datasheet (Alliance Semiconductor)

r

r

r

r

r

查询ASM3P2769A供应商

September 2005 ASM3P2769A

rev 1.8

Low Power Peak EMI Reducing Solution

Features

 Generates an EMI optimized clock signal at the

output.

 Integrated loop filter components.

 Operates with a 3.3V / 2.5V Supply

 Operating current less than 4mA.

 Low power CMOS design.

 Input frequency range: 6MHz to 12MHz for 2.5V.

: 6MHz to 13MHz for 3.3V.

 Generates a 1X low EMI spread spectrum clock of

the input frequency.

 Frequency deviation: ±1% @ 10MHz

 Available in 6 pin TSOT-23, 8 pin SOIC and

8 pin TSSOP Packages.

Product Description

The ASM3P2769A is a versatile spread spectrum

frequency modulator designed specifically for a wide

range of clock frequencies. The ASM3P2769A reduces

electromagnetic interference (EMI) at the clock source,

allowing system wide reduction of EMI of all clock

dependent signals. The ASM3P2769A allows significant

system cost savings by reducing the number of circuit

board layers ferrite beads, shielding that are traditionally

required to pass EMI regulations.

Block Diagram

VDD

PD

The ASM3P2769A uses the most efficient and optimized

modulation profile approved by the FCC and is

implemented by using a proprietary all digital method.

The ASM3P2769A modulates the output of a single PLL

in order to “spread” the bandwidth of a synthesized clock,

and more importantly, decreases the peak amplitudes of

its harmonics. This results in significantly lower system

EMI compared to the typical narrow band signal produced

by oscillators and most frequency generators. Lowering

EMI by increasing a signal’s bandwidth is called ‘spread

spectrum clock generation’.

Applications

The ASM3P2769A is targeted towards all portable

devices with very low power requirements like MP3

players and digital still cameras.

Key Specifications

Description Specification

Supply voltages VDD = 3.3V / 2.5V

Cycle-to-Cycle Jitter 200pS (Max)

Output Duty Cycle 45/55%

Modulation Rate Equation FIN/256

Frequency Deviation ±1% @ 10MHz

VCO

PLL

Output
Divide

ModOUT

XIN

XOUT

Crystal

Frequency

Divide

Feedback

Divide

VSS

Modulation

Phase

Detecto

Alliance Semiconductor

Loop
Filte

2575 Augustine Drive • Santa Clara, CA • Tel: [phone] • Fax: [phone] • www.alsc.com

Notice: The information in this document is subject to change without notice.

September 2005

ASM3P2769A

rev 1. 8

Pin Configuration (6-pin TSOT-23 Package)

XIN/CLKIN

Pin Description

Pin# Pin Name Type Description

1

2 XOUT O Crystal connection. If using an external reference, this pin must be left unconnected.

3 XIN/CLKIN I

4 VDD P Power supply for the entire chip.

PD

Power-down control pin. Pull low to enable power-down mode. Connect to VDD if not

I

used.

Crystal connection or external reference frequency input. This pin has dual functions. It
can be connected either to an external crystal or an external reference clock.

PD

XOUT

1

ASM3P2769A

2

3

6

VSS

5

ModOUT

VDD

4

5 ModOUT O Spread spectrum clock output.

6 VSS P Ground connection.

Low Power Peak EMI Reducing Solution 2 of 12

Notice: The information in this document is subject to change without notice.

September 2005

ASM3P2769A

rev 1. 8

Pin Configuration (8-pin SOIC and TSSOP Packages)

XIN/CLKIN

Pin Description

Pin# Pin Name Type Description

1 XIN/CLKIN I

2 XOUT O Crystal connection. If using an external reference, this pin must be left unconnected.

3

4 NC - No connect.

PD

Crystal connection or external reference frequency input. This pin has dual functions. It
can be connected either to an external crystal or an external reference clock.

Power-down control pin. Pull low to enable power-down mode. Connect to VDD if not

I

used.

XOUT

PD

1

2

ASM3P2769A

3

4

8

VDD

NC

7

6

ModOUT

5

VSS

5 VSS P Ground connection.

6 ModOUT O Spread spectrum clock output.

7 NC - No connect.

8 VDD P Power supply for the entire chip.

Modulation Profile

Specification

Description Specification

Frequency

Range

For 2.5V Supply 6MHz < CLKIN < 12MHz
For 3.3V Supply

Modulation Equation FIN/256

Frequency Deviation ±1% @ 10MHz

6MHz < CLKIN < 13MHz

Low Power Peak EMI Reducing Solution 3 of 12

Notice: The information in this document is subject to change without notice.

September 2005

ASM3P2769A

rev 1. 8

Absolute Maximum Ratings

Symbol Parameter Rating Unit

VDD, VIN Voltage on any pin with respect to Ground -0.5 to +7.0 V

T

Storage temperature -65 to +125 °C

STG

TA Operating temperature 0 to 70 °C

Ts Max. Soldering Temperature (10 sec) 260 °C

TJ Junction Temperature 150 °C

TDV

Note: These are stress ratings only and are not implied for functional use. Exposure to absolute maximum ratings for prolonged periods of time may affect
device reliability.

DC Electrical Characteristics for 2.5V Supply

(Test condition: All parameters are measured at room temperature (+25°C) unless otherwise stated.)

Symbol Parameter Min Typ Max Unit

VIL Input low voltage VSS-0.3 - 0.8 V

VIH Input high voltage 2.0 - VDD+0.3 V

IIL Input low current - - -35 µA

IIH Input high current - - 35 µA

I

XOUT output low current (@0.5V, VDD=2.5V) - 3 - mA

XOL

I

XOUT output high current (@1.8V, VDD=2.5V) - 3 - mA

XOH

VOL Output low voltage (VDD = 2.5 V, IOL = 8mA) - - 0.6 V

VOH Output high voltage (VDD = 2.5 V, IOH = 8mA) 1.8 - - V

IDD Static supply current * - - 10 µA

ICC Dynamic supply current (2.5V, 10MHz and with no load) - 2.5 - mA

VDD Operating Voltage 2.375 2.5 2.625 V

tON Power-up time(first locked cycle after power up)** - - 5 mS

Z

Output impedance - 50 - Ω

OUT

* XIN/CLKIN pin and PD pin are pulled low
** VDD and XIN/CLKIN input are stable; PD pin is made high from low.

AC Electrical Characteristics for 2.5V Supply

Symbol Parameter Min Typ Max Unit

CLKIN Input frequency 6 - 12 MHz

Static Discharge Voltage

(As per JEDEC STD22- A114-B)

2 KV

ModOUT Output frequency 6 - 12 MHz

Input Frequency = 6MHz - ±1.55 -

fd Frequency Deviation

%

Input Frequency = 12MHz - ±0.8 -

tLH* Output rise time (measured at 0.7V to 1.7V) 0.6 1.2 1.5 nS

tHL* Output fall time (measured at 1.7V to 0.7V) 0.4 0.9 1.1 nS

tJC Jitter (cycle to cycle) - - 200 pS

tD Output duty cycle 45 50 55 %

*tLH and tHL are measured into a capacitive load of 15pF

Low Power Peak EMI Reducing Solution 4 of 12

Notice: The information in this document is subject to change without notice.

September 2005

ASM3P2769A

rev 1. 8

DC Electrical Characteristics for 3.3V Supply

(Test condition: All parameters are measured at room temperature (+25°C) unless otherwise stated).

Symbol Parameter Min Typ Max Unit

VIL Input low voltage VSS - 0.3 - 0.8 V

VIH Input high voltage 2.0 - VDD + 0.3 V

IIL Input low current - - -35 µA

IIH Input high current - - 35 µA

I

XOUT output low current (@0.4V, VDD=3.3V) - 3 - mA

XOL

I

XOUT output high current (@2.5V, VDD=3.3V) - 3 - mA

XOH

VOL Output low voltage (VDD = 3.3 V, IOL = 8mA) - - 0.4 V

VOH Output high voltage (VDD = 3.3 V, IOH = 8mA) 2.5 - - V

IDD Static supply current * - - 10 µA

ICC Dynamic supply current (3.3V, 10MHz and with no load) - 3.5 - mA

VDD Operating Voltage 2.7 3.3 3.6 V

tON Power-up time(first locked cycle after power up)** - - 5 mS

Z

Output impedance - 45 - Ω

OUT

* XIN/CLKIN pin and PD pin are pulled low
** VDD and XIN/CLKIN input are stable, PD pin is made high from low.

AC Electrical Characteristics for 3.3V Supply

Symbol Parameter Min Typ Max Unit

CLKIN Input frequency 6 - 13 MHz

ModOUT Output frequency 6 - 13 MHz

fd Frequency Deviation

tLH* Output rise time (measured at 0.8V to 2.0V) 0.4 1.2 1.4 nS

tHL* Output fall time (measured at 2.0V to 0.8V) 0.3 0.9 1.1 nS

tJC Jitter (cycle to cycle) - - 200 pS

tD Output duty cycle 45 50 55 %

*tLH and tHL are measured into a capacitive load of 15pF

Input Frequency = 6MHz - ±1.55 -

%

Input Frequency = 13MHz - ±0.75 -

Low Power Peak EMI Reducing Solution 5 of 12

Notice: The information in this document is subject to change without notice.

September 2005

ASM3P2769A

rev 1. 8

Typical Crystal Oscillator Circuit

Crystal

C1 = 27 pF

R1 = 510Ω

C2 = 27 pF

Typical Crystal Specifications

Fundamental AT cut parallel resonant crystal

Nominal frequency 8.000MHz

Frequency tolerance ± 50 ppm or better at 25°C

Operating temperature range -25°C to +85°C

Storage temperature -40°C to +85°C

Load capacitance 18pF

Shunt capacitance 7pF maximum

ESR 25Ω

Low Power Peak EMI Reducing Solution 6 of 12

Notice: The information in this document is subject to change without notice.

September 2005

ASM3P2769A

rev 1. 8

Package Information

6-pin TSOT-23 Package

Dimensions

Symbol

Inches

Millimeters

Min Max Min Max

A 0.04 1.00

A1 0.00 0.004 0.00 0.10

A2 0.033 0.036 0.84 0.90

b 0.012 0.02 0.30 0.50

H 0.005 BSC 0.127 BSC

D 0.114 BSC 2.90 BSC

B 0.06 BSC 1.60 BSC

e 0.0374 BSC 0.950 BSC

C 0.11 BSC 2.80 BSC

L 0.0118 0.02 0.30 0.50

θ 0° 4° 0° 4°

Low Power Peak EMI Reducing Solution 7 of 12

Notice: The information in this document is subject to change without notice.

C

September 2005

rev 1. 8

ASM3P2769A

8-Pin SOIC Package

H

E

D

A2

A

e

B

Symbol

A1

D

Inches

Min Max Min Max

θ

Dimensions

Millimeters

L

A1 0.004 0.010 0.10 0.25

A 0.053 0.069 1.35 1.75

A2 0.049 0.059 1.25 1.50

B 0.012 0.020 0.31 0.51

C 0.007 0.010 0.18 0.25

D 0.193 BSC 4.90 BSC

E 0.154 BSC 3.91 BSC

e 0.050 BSC 1.27 BSC

H 0.236 BSC 6.00 BSC

L 0.016 0.050 0.41 1.27

θ 0° 8° 0° 8°

Low Power Peak EMI Reducing Solution 8 of 12

Notice: The information in this document is subject to change without notice.

C

September 2005

rev 1. 8

ASM3P2769A

8-Pin TSSOP Package

H

E

D

e

B

A2

A

θ

A1

L

Dimensions

Symbol

Inches Millimeters

Min Max Min Max

A

A1 0.002 0.006 0.05 0.15

A2 0.033 0.037 0.85 0.95

B 0.008 0.012 0.19 0.30

c 0.004 0.008 0.09 0.20

D 0.114 0.122 2.90 3.10

E 0.169 0.177 4.30 4.50

e 0.026 BSC 0.65 BSC

H 0.252 BSC 6.40 BSC

L 0.020 0.028 0.50 0.70

θ 0° 8° 0° 8°

0.043

1.10

Low Power Peak EMI Reducing Solution 9 of 12

Notice: The information in this document is subject to change without notice.

September 2005

ASM3P2769A

rev 1. 8

Ordering Information

Part Number Marking Package Type Temperature

ASM3P2769AF-06OR F4LL 6-Pin TSOT-23, TAPE & REEL, Pb Free Commercial

ASM3P2769AF-08TT 3P2769AF 8-Pin TSSOP, TUBE, Pb Free Commercial

ASM3P2769AF-08TR 3P2769AF 8-Pin TSSOP, TAPE & REEL, Pb Free Commercial

ASM3P2769AF-08ST 3P2769AF 8-Pin SOIC, TUBE, Pb Free Commercial

ASM3P2769AF-08SR 3P2769AF 8-Pin SOIC, TAPE & REEL, Pb Free Commercial

ASM3P2769AG-06OR F3LL 6-Pin TSOT-23, TAPE & REEL, Green Commercial

ASM3P2769AG-08TT 3P2769AG 8-Pin TSSOP, TUBE, Green Commercial

ASM3P2769AG-08TR 3P2769AG 8-Pin TSSOP, TAPE & REEL, Green Commercial

ASM3P2769AG-08ST 3P2769AG 8-Pin SOIC, TUBE, Green Commercial

ASM3P2769AG-08SR 3P2769AG 8-Pin SOIC, TAPE & REEL, Green Commercial

ASM3P2769A-06OR F1LL 6-Pin TSOT-23, TAPE & REEL Commercial

ASM3P2769A-08TT 3P2769A 8-Pin TSSOP, TUBE Commercial

ASM3P2769A-08TR 3P2769A 8-Pin TSSOP, TAPE & REEL Commercial

ASM3P2769A-08ST 3P2769A 8-Pin SOIC, TUBE Commercial

ASM3P2769A-08SR 3P2769A 8-Pin SOIC, TAPE & REEL Commercial

ASM3I2769AF-06OR F5LL 6-Pin TSOT-23, TAPE & REEL, Pb Free Industrial

ASM3I2769AF-08TT 3I2769AF 8-Pin TSSOP, TUBE, Pb Free Industrial

ASM3I2769AF-08TR 3I2769AF 8-Pin TSSOP, TAPE & REEL, Pb Free Industrial

ASM3I2769AF-08ST 3I2769AF 8-Pin SOIC, TUBE, Pb Free Industrial

ASM3I2769AF-08SR 3I2769AF 8-Pin SOIC, TAPE & REEL, Pb Free Industrial

ASM3I2769AG-06OR F6LL 6-Pin TSOT-23, TAPE & REEL, Green Industrial

ASM3I2769AG-08TT 3I2769AG 8-Pin TSSOP, TUBE, Green Industrial

ASM3I2769AG-08TR 3I2769AG 8-Pin TSSOP, TAPE & REEL, Green Industrial

ASM3I2769AG-08ST 3I2769AG 8-Pin SOIC, TUBE, Green Industrial

ASM3I2769AG-08SR 3I2769AG 8-Pin SOIC, TAPE & REEL, Green Industrial

ASM3I2769A-06OR F2LL 6-Pin TSOT-23, TAPE & REEL Industrial

ASM3I2769A-08TT 3I2769A 8-Pin TSSOP, TUBE Industrial

ASM3I2769A-08TR 3I2769A 8-Pin TSSOP, TAPE & REEL Industrial

ASM3I2769A-08ST 3I2769A 8-Pin SOIC, TUBE Industrial

ASM3I2769A-08SR 3I2769A 8-Pin SOIC, TAPE & REEL Industrial

Low Power Peak EMI Reducing Solution 10 of 12

Notice: The information in this document is subject to change without notice.

y

September 2005

ASM3P2769A

rev 1. 8

Device Ordering Information

ASM3P2769AF-08TR

Licensed under U.S Patent Nos 5,488,627 and 5,631,921

R = Tape & reel, T = Tube or Tray

O = SOT U = MSOP
S = SOIC E = TQFP
T = TSSOP L = LQFP
A = SSOP U = MSOP
V = TVSOP P = PDIP
B = BGA D = QSOP

=

DEVICE PIN COUNT

F = LEAD FREE AND RoHS COMPLIANT PART
G = GREEN PACKAGE

PART NUMBER

X= Automotive I= Industrial P or n/c = Commercial
(-40C to +125C) (-40C to +85C) (0C to +70C)

1 = Reserved 6 = Power Management
2 = Non PLL based 7 = Power Management
3 = EMI Reduction 8 = Power Management
4 = DDR support products 9 = Hi Performance
5 = STD Zero Dela

ALLIANCE SEMICONDUCTOR MIXED SIGNAL PRODUCT

Buffer 0 = Reserved

=

-

Low Power Peak EMI Reducing Solution 11 of 12

Notice: The information in this document is subject to change without notice.

September 2005

ASM3P2769A

rev 1. 8

Alliance Semiconductor Corporation
2575 Augustine Drive,
Santa Clara, CA 95054
Tel# [phone]
Fax: [phone]
www.alsc.com

Note: This product utilizes US Patent # 6,646,463 Impedance Emulator Patent issued to Alliance Semiconductor, dated 11-11-2003

© Copyright 2003 Alliance Semiconductor Corporation. All rights reserved. Our three-point logo, our name and Intelliwatt are
trademarks or registered trademarks of Alliance. All other brand and product names may be the trademarks of their respective
companies. Alliance reserves the right to make changes to this document and its products at any time without notice. Alliance
assumes no responsibility for any errors that may appear in this document. The data contained herein represents Alliance's
best data and/or estimates at the time of issuance. Alliance reserves the right to change or correct this data at any time,
without notice. If the product described herein is under development, significant changes to these specifications are possible.
The information in this product data sheet is intended to be general descriptive information for potential customers and users,
and is not intended to operate as, or provide, any guarantee or warrantee to any user or customer. Alliance does not assume
any responsibility or liability arising out of the application or use of any product described herein, and disclaims any express or
implied warranties related to the sale and/or use of Alliance products including liability or warranties related to fitness for a
particular purpose, merchantability, or infringement of any intellectual property rights, except as express agreed to in Alliance's
Terms and Conditions of Sale (which are available from Alliance). All sales of Alliance products are made exclusively
according to Alliance's Terms and Conditions of Sale. The purchase of products from Alliance does not convey a license under
any patent rights, copyrights; mask works rights, trademarks, or any other intellectual property rights of Alliance or third
parties. Alliance does not authorize its products for use as critical components in life-supporting systems where a malfunction
or failure may reasonably be expected to result in significant injury to the user, and the inclusion of Alliance products in such
life-supporting systems implies that the manufacturer assumes all risk of such use and agrees to indemnify Alliance against all
claims arising from such use.

Copyright © Alliance Semiconductor
All Rights Reserved
Preliminary Information
Part Number: ASM3P2769A
Document Version: v1.8

Low Power Peak EMI Reducing Solution 12 of 12

Notice: The information in this document is subject to change without notice.