Datasheet AMS1503 Datasheet (Advanced Monolithic Systems)

查询AMS1503供应商

Advanced AMS1503
Monolithic 3A LOW DROPOUT VOLTAGE REGULATORS

Systems

FEATURES APPLICATIONS

•• Adjustable or Fixed Output •• High Current Regulators

1.5V, 2.5V, 2.85V, 3.0V, 3.3V, 3.5V and 5.0V

•• Output Current of 3A •• Adjustable Power Supply

•• Low Dropout, 500mV at 3A Output Current •• Notebook/Personal Computer Supplies

•• Fast Transient Response

•• Remote Sense

GENERAL DESCRIPTION

The AMS1503 series of adjustable and fixed low dropout voltage regulators are designed to provide 3A output current to
power the new generation of microprocessors. The dropout voltage of the device is 100mV at light loads and rising to 500mV
at maximum output current. A second low current input voltage 1V or greater then the output voltage is required to achieve
this dropout. The AMS1503 can also be used as a single supply device.
New features have been added to the AMS1503: a remote Sense pin is brought out virtually eliminating output voltage
variations due to load changes. The typical load regulation, measured at the Sense pin, for a load current step of 100mA to 3A
is less than 1mV.
The AMS1503 series has fast transient response. The Adjust pin is brought out on fixed devices. To further improve the
transient response the addition of a small capacitor on the Adjust pin is recommended.
The AMS1503 series are ideal for generating power supplies of 2V to 3V where both 5V and 3.3V supplies are available.
The AMS1503 devices are offered in 5 lead TO-220 and TO-263 (plastic DD) packages and in the 7 lead TO-220 package.

•• Post Regulators for Switching Supplies

ORDERING INFORMATION: PIN CONNECTIONS

PACKAGE TYPE OPERATING JUNCTION

5 LEAD TO-263 5 LEAD TO-220 7 LEAD TO-220

AMS1503CM AMS1503CT AMS1503CT-1.5
AMS1503CM-1.5 AMS1503CT-1.5 AMS1503CT-2.5
AMS1503CM-2.5 AMS1503CT-2.5 AMS1503CT-2.85
AMS1503CM-2.85 AMS1503CT-2.85 AMS1503CT-3.0
AMS1503CM-3.0 AMS1503CT-3.0 AMS1503CT-3.3
AMS1503CM-3.3 AMS1503CT-3.3 AMS1503CT-3.5
AMS1503CM-3.5 AMS1503CT-3.5 AMS1503CT-5.0
AMS1503CM-5.0 AMS1503CT-5.0

TEMPERATURE RANGE

0 to 125° C
0 to 125° C
0 to 125° C
0 to 125° C
0 to 125° C
0 to 125° C
0 to 125° C
0 to 125° C

5 LEAD TO-220

5
4
3
2
1

FRONT VIEW

7 LEAD TO-220

7
6
5
4
3
2
1

FRONT VIEW

5 LEAD TO-263

5
4
3
2
1

FRONT VIEW

V

POWER

V

CONTROL

OUTPUT

ADJUST/GND

SENSE

NC
ADJUST

Vcontrol
SENSE

Vpower
Vcontrol
OUTPUT
ADJUST/GND
SENSE

Vpower

OUTPUT
GND

Advanced Monolithic Systems 6680B Sierra Lane, Dublin, CA 94568 Phone [phone] Fax [phone]

AMS1503

Junction Temperature Range

ABSOLUTE MAXIMUM RATINGS (Note 1)

V

Input Voltage 6V Soldering information

POWER

V
Operating
Control Section
Power Transistor
Storage temperature

ELECTRICAL CHARACTERISTICS

Electrical Characteristics at I

Parameter Device Conditions Min Typ Max Units

CONTROL

Input Voltage 13V Lead Temperature (10 sec)

Thermal Resistance

0°C to 125°C

0°C to 150°C

- 65°C to +150°C

= 0 mA, and TJ = +25°C unless otherwise specified.

LOAD

TO-220 package
TO-263 package

* With package soldering to 0.5in2 copper area over backside ground
plane or internal power plane ϕ
depending on mounting technique.

can vary from 20°C/W to >40°C/W

JA

300°C

ϕ JA= 50°C/W

ϕ JA= 30°C/W*

Reference Voltage AMS1503 V

Output Voltage AMS1503-1.5 V

AMS1503-2.5 V

AMS1503-2.85 V

AMS1503-3.0 V

AMS1503-3.3 V

AMS1503-3.5 V

AMS1503-5.0 V

Line Regulation AMS1503/-1.5/-2.5/

-2.85/-3.0/-3.3/-3.5/-5.0

Load Regulation AMS1503/-1.5/-2.5/

-2.85/-3.0/-3.3/-3.5/-5.0

Minimum Load

AMS1503 V

Current
Control Pin Current

(Note 4)

Ground Pin Current
(Note 4)

AMS1503/-1.5/-2.5/

-2.85/-3.0/-3.3/-3.5/-5.0
AMS1503-1.5/-2.5/-2.85/

-3.0/-3.3/-3.5/-5.0

= 2.75V, V

CONTROL

V

= 2.7V to 12V, V

CONTROL

I

= 10mA to 3A

LOAD

= 4V, V

CONTROL

V

= 3V, V

CONTROL

= 5V, V

CONTROL

V

= 4V, V

CONTROL

= 5.35V, V

CONTROL

V

= 4.4V, V

CONTROL

= 5.5V, V

CONTROL

V

= 4.5V, V

CONTROL

= 5.8V, V

CONTROL

V

= 4.8V, V

CONTROL

= 6V, V

CONTROL

V

= 5V, V

CONTROL

= 7.5V, V

CONTROL

V

= 6.5V, V

CONTROL

I

= 10 mA , 1.5V≤ (V

LOAD

0.8V≤ (V

POWER

V

= V

CONTROL

I

= 10mA to 3A

LOAD

= 5V, V

CONTROL

V

= V

CONTROL

I

= 10mA to 3A

LOAD

V

= V

CONTROL

I

= 10mA to 3A

LOAD

POWER
POWER

POWER
POWER

POWER
POWER

- V
+ 2.5V, V

OUT

POWER

+ 2.5V, V

OUT

+ 2.5V, V

OUT

POWER

POWER

POWER

POWER
POWER

POWER
POWER

POWER
POWER

OUT

=2V, I

POWER

=2.V, I
=2.3V, I

=3.3V, I
=3.3V, I

=3.35V, I

=3.7V, I
=3.5V, I

=3.8V, I
=3.8V, I

=4.1V, I

=4V, I
=4.3V, I

=5.5V, I
=5.8V, I

CONTROL

) ≤ 5.5V

POWER

=3.3V, V

POWER

POWER

= 10mA

LOAD

=3.3V to 5.5V,

= 0mA

LOAD

= 0mA to 3A

LOAD

= 0mA

LOAD

= 0mA to 3A

LOAD

= 0mA

LOAD

= 0mA to 3A

LOAD

= 0mA

LOAD

= 0mA to 3A

LOAD

= 0mA

LOAD

= 0mA to 3A

LOAD

= 0mA

LOAD

= 0mA to 3A

LOAD

= 0mA

LOAD

= 0mA to 3A

LOAD

- V

) ≤ 12V

OUT

=V

+ 0.8V,

OUT

= 0V (Note 3)

ADJ

=V

+ 0.8V,

OUT

=V

+ 0.8V,

OUT

1.243

1.237

1.491

1.485

2.485

2.475

2.821

2.833

2.982

2.970

3.280

3.235

3.479

3.430

4.930

4.950

1.250

1.250

1.500

1.500

2.500

2.500

2.850

2.850

3.000

3.000

3.300

3.300

3.500

3.500

5.000

5.000
1 3

1 5

5 10

6 60 120

6 10

1.257

1.263

1.509

1.515

2.515

2.525

2.879

2.867

3.018

3.030

3.320

3.333

3.521

3.535

5.030

5.050

V
V

V
V

V
V

V
V

V
V

V
V

V
V

V
V

mV

mA

mA

mA

mA

Adjust Pin Current AMS1503 V
Current Limit AMS1503/-1.5/-2.5/

CONTROL

(VIN - V

= 2.75V, V

) = 5V

OUT

POWER

= 2.05V, I

LOAD

= 10mA

5 120

3.0 3.5 4.0

µA

A

-2.85/-3.0/-3.3/-3.5/-5.0

Ripple Rejection AMS1503/-1.5/-2.5/

-2.85/-3.0/-3.3/-3.5/-5.0

V

CONTROL

I

LOAD

= V

= 1.5A

POWER

= V

+ 2.5V, V

OUT

RIPPLE

= 1V

P-P

60 80 dB

Thermal Regulation AMS1503 TA = 25°C, 30ms pulse 0.002 0.020 %W
Thermal Resistance

Junction-to-Case

T Package: Control Circuitry/ Power Transistor
M Package: Control Circuitry/ Power Transistor

0.65/2.70

0.65/2.70

°C/W
°C/W

Advanced Monolithic Systems 6680B Sierra Lane, Dublin, CA 94568 Phone [phone] Fax [phone]

AMS1503

ELECTRICAL CHARACTERISTICS

Electrical Characteristics at I

Parameter Device Conditions Min Typ Max Units

= 0 mA, and TJ = +25°C unless otherwise specified.

OUT

Dropout Voltage

Control Dropout
(V

Power Dropout
(V

Parameters identified with boldface type apply over the full operating temperature range.

CONTROL

POWER

- V

- V

OUT

OUT

)

AMS1503/-1.5/-2.5/-

)

2.85/-3.0/-3.3/-3.5/-5.0

AMS1503/-1.5/-2.5/-

2.85/-3.0/-3.3/-3.5/-5.0

Note 2

V

POWER

V

POWER

V

CONTROL

V

CONTROL

V

CONTROL

=V
=V

=V
=V
=V

OUT

OUT

OUT

OUT

OUT

+ 0.8V, I
+ 0.8V, I

+ 2.5V, I
+ 2.5V, I
+ 2.5V, I

LOAD

LOAD

LOAD

LOAD

LOAD

= 10mA
= 3A

= 10mA
= 2A
= 3A

1.00

1.15

0.10

0.30

0.35

1.15

1.30

0.17

0.45

0.50

V
V

V
V
V

Note 1: Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. For guaranteed specifications and test conditions, see the

Electrical Characteristics. The guaranteed specifications apply only for the test conditions listed.

Note 2: Unless otherwise specified V

OUT

= V

. For the adjustable device V

SENSE

ADJ

= 0V.

Note 3: The dropout voltage for the AMS1503 is caused by either minimum control voltage or minimum power voltage. The specifications represent the minimum

input/output voltage required to maintain 1% regulation.

Note 4: For the adjustable device the minimum load current is the minimum current required to maintain regulation. Normally the current in the resistor divider

used to set the output voltage is selected to meet the minimum load current requirement.

Note 5: The control pin current is the drive current required for the output transistor. This current will track output current with a ratio of about 1:100. The

minimum value is equal to the quiescent current of the device.

PIN FUNCTIONS

Sense (Pin 1): This pin is the positive side of the

reference voltage for the device. With this pin it is
possible to Kelvin sense the output voltage at the load.

Adjust (Pin 2/5): This pin is the negative side of the
reference voltage for the device. Adding a small bypass
capacitor from the Adjust pin to ground improves the
transient response. For fixed voltage devices the Adjust
pin is also brought out to allow the user to add a bypass
capacitor.

GND (Pin 2, 7-Lead only): For fixed voltage devices this
is the bottom of the resistor divider that sets the output
voltage.

V

(Pin 5/6): This pin is the collector to the power

POWER

device of the AMS1503. The output load current is
supplied through this pin. The voltage at this pin must
be between 0.1V and 0.8V greater than the output
voltage for the device to regulate.

V

CONTROL

(Pin 4/3): This pin is the supply pin for the

control circuitry of the device. The current flow into
this pin will be about 1% of the output current. The
voltage at this pin must be 1.3V or greater than the
output voltage for the device to regulate.

Output (Pin 3/4): This is the power output of the
device.

Advanced Monolithic Systems 6680B Sierra Lane, Dublin, CA 94568 Phone [phone] Fax [phone]

APPLICATION HINTS

AMS1503

The AMS1503 series of adjustable and fixed regulators are
designed to power the new generation of microprocessors. The
AMS1503 is designed to make use of multiple power supplies,
existing in most systems, to reduce the dropout voltage. One of
the advantages of the two supply approach is maximizing the
efficiency.
The second supply is at least 1V greater than output voltage and
is providing the power for the control circuitry and supplies the
drive current to the NPN output transistor. This allows the NPN
to be driven into saturation; thereby reducing the dropout voltage
by a VBE compared to conventional designs. For the control
voltage the current requirement is small equal to about 1% of the
output current or approximately 30mA for a 3A load. Most of this
current is drive current for the NPN output transistor. This drive
current becomes part of the output current. The maximum voltage
on the Control pin is 13V. The maximum voltage at the Power
pin is 7V. Ground pin current for fixed voltage devices is typical
6mA and is constant as a function of load. Adjust pin current for
adjustable devices is 60µA at 25°C and varies proportional to
absolute temperature.
The improved frequency compensation of AMS1503 permits the
use of capacitors with very low ESR. This is critical in addressing
the needs of modern, low voltage high sped microprocessors. The
new generation of microprocessors cycle load current from several
hundred mA to several A in tens of nanoseconds. Output voltage
tolerances are tighter and include transient response as part of the
specification. Designed to meet the fast current load step
requirements of these microprocessors, the AMS1503 also saves
total cost by needing less output capacitance to maintain
regulation.
Careful design of the AMS1503 has eliminated any supply
sequencing issues associated with a dual supply system. The
output voltage will not turn on until both supplies are operating.
If the control voltage comes up first, the output current will be
limited to a few milliamperes until the power input voltage comes
up. If power input comes up first the output will not turn on at all
until the control voltage comes up. The output can never come up
unregulated. By tying the control and power inputs together the
AMS1503 can also be operated as a single supply device. In
single supply operation the dropout will be determined by the
minimum control voltage.
The new features of the AMS1503 require additional pins over
the traditional 3-terminal regulator. Both the fixed and adjustable
versions have remote sense pins, permitting very accurate
regulation of output voltage at the load, rather than at the
regulator. As a result, over an output current range of 100mA to
3A with a 2.5V output, the typical load regulation is less than
1mV. For the fixed voltages the adjust pin is brought out allowing
the user to improve transient response by bypassing the internal
resistor divider. Optimum transient response is provided using a
capacitor in the range of 0.1µF to 1µF for bypassing the Adjust
pin. The value chosen will depend on the amount of output
capacitance in the system.
In addition to the enhancements mentioned, the reference
accuracy has been improved by a factor of two with a guaranteed
initial tolerance of ±0.6% at 25°C. This device can hold 1%
accuracy over the full temperature range and load current range,

guaranteed, when combined with ratiometrically accurate internal
divider resistors and operating with an input/output differential of
well under 1V.
Typical applications for the AMS1503 include 3.3V to 2.5V
conversion with a 5V control supply, 5V to 4.2V conversion with
a 12V control supply or 5V to 3.6V conversion with a 12V
control supply. Capable of 3A of output current with a maximum
dropout of 0.8V the AMS1503 also has a fast transient response
that allows it to handle large current changes associated with the
new generation of microprocessors. The device is fully protected
against overcurrent and overtemperature conditions.

Grounding and Output Sensing

The AMS1503 allows true Kelvin sensing for both the high and
low side of the load. As a result the voltage regulation at he load
can be easily optimized. Voltage drops due to parasitic
resistances between the regulator and the load can be placed
inside the regulation loop of the AMS1503. The advantages of
remote sensing are illustrated in figures 1 through 3.
Figure 1 shows the device connected as a conventional 3 terminal
regulator with the Sense lead connected directly to the output of
the device. RP is the parasitic resistance of the connections
between the device and the load. Typically the load is a
microprocessor and RP is made up of the PC traces and /or
connector resistances (in the case of a modular regulator)
between the regulator and the processor. Trace A of figure 3
illustrates the effect of RP. Very small resistances cause
significant load regulation steps.
Figure 2 shows the device connected to take advantage of the
remote sense feature. The Sense pin and the top of the resistor
divider are connected to the top of the load; the bottom of the
resistor divider is connected to the bottom of the load. RP is now
connected inside the regulation loop of the AMS1503 and for
reasonable values of RP the load regulation at the load will be
negligible. The effect on output regulation can be seen in trace B
of figure 3.

5V

CONTROL

3.3V

POWER SENSE

AMS1503

OUTPUT

ADJ

R1

R2

R

P

LOAD

R

P

+

V

OUT

-

Figure 1. Conventional Load Sensing

Advanced Monolithic Systems 6680B Sierra Lane, Dublin, CA 94568 Phone [phone] Fax [phone]

APPLICATION HINTS

ADJ

5V

CONTROL

3.3V

POWER SENSE

AMS1503

OUTPUT

ADJ

R1

R2

Figure 2. Remote Load Sensing

V

OUT

FIGURE 1

V

OUT

FIGURE 2

(∆I

OUT

R

R

P

)(RP)

AMS1503

to allow this capability. To ensure good transient response with
heavy load current changes capacitor values on the order of
100µF are used in the output of many regulators. To further
improve stability and transient response of these devices larger
values of output capacitor can be used.
The modern processors generate large high frequency current
transients. The load current step contains higher order frequency

P

LOAD

+

V

OUT

-

components than the output coupling network must handle until
the regulator throttles to the load current level. Because they
contain parasitic resistance and inductance, capacitors are not
ideal elements. These parasitic elements dominate the change in
output voltage at the beginning of a transient load step change.
The ESR of the output capacitors produces an instantaneous step
in output voltage (∆V=∆I)(ESR). The ESL of the output
capacitors produces a droop proportional to the rate of change of
the output current (V= L)(∆I/∆t). The output capacitance
produces a change in output voltage proportional to the time until
the regulator can respond (∆V=∆t) (∆I/C). Figure 4 illustrates
these transient effects.

ESR
EFFECTS

ESL
EFFECTS

CAPACITANCE
EFFECTS

I

OUT

TIME

Figure 3. Remote Sensing Improves Load Regulation

Voltage drops due to RP are not eliminated; they will add to the
dropout voltage of the regulator regardless of whether they are
inside or outside the regulation loop. The AMS1503 can control
the voltage at the load as long as the input-output voltage is
greater than the total of the dropout voltage of the device plus the
voltage drop across RP.

Stability

The circuit design used in the AMS1503 series requires the use of
an output capacitor as part of the device frequency compensation.
The addition of 150µF aluminum electrolytic or a 22µF solid
tantalum on the output will ensure stability for all operating
conditions. For best frequency response use capacitors with an
ESR of less than 1Ω.
In order to meet the transient requirements of the processor larger
value capacitors are needed. Tight voltage tolerances are required
in the power supply. To limit the high frequency noise generated
by the processor high quality bypass capacitors must be used. In
order to limit parasitic inductance (ESL) and resistance (ESR) in
the capacitors to acceptable limits, multiple small ceramic
capacitors in addition to high quality solid tantalum capacitors are
required.
When the adjustment terminal is bypassed to improve the ripple
rejection, the requirement for an output capacitor increases. The
Adjust pin is brought out on the fixed voltage device specifically

SLOPE, V/t = ∆I/C

POINT AT WHICH REGULATOR

TAKES CONTROL

Figure 4.

Output Voltage

The AMS1503 series develops a 1.25V reference voltage
between the Sense pin and the Adjust pin (Figure5). Placing a
resistor between these two terminals causes a constant current to
flow through R1 and down through R2 to set the overall output
voltage. In general R1 is chosen so that this current is the
specified minimum load current of 10mA.The current out of the
Adjust pin is small, typically 50µA and it adds to the current
from R1. Because I

is very small it needs to be considered
only when very precise output voltage setting is required. For
best regulation the top of the resistor divider should be connected
directly to the Sense pin.

V

CONTROL

CONTROL

POWER OUTPUT

AMS1503

SENSE

ADJ

I

ADJ

50µA

R2

ADJ

V

+

V

REF

R1

OUT

R2

V

V

OUT

POWER

= V

+

+

(1+ R2/R1)+I

REF

Figure 5. Setting Output Voltage

Advanced Monolithic Systems 6680B Sierra Lane, Dublin, CA 94568 Phone [phone] Fax [phone]

APPLICATION HINTS

POWER

POWER

POWER

CONTROL

OUT

AMS1503

Protection Diodes

Unlike older regulators, the AMS1503 family does not need any
protection diodes between the adjustment pin and the output and
from the output to the input to prevent die over-stress. Internal
resistors are limiting the internal current paths on the AMS1503
adjustment pin, therefore even with bypass capacitors on the
adjust pin no protection diode is needed to ensure device safety
under short-circuit conditions. The Adjust pin can be driven on a
transient basis ±7V with respect to the output without any device
degradation.
Diodes between the Output pin and V

pin are not usually
needed. Microsecond surge currents of 25A to50A can be handled
by the internal diode between the Output pin and V

pin of
the device. In normal operations it is difficult to get those values
of surge currents even with the use of large output capacitances. If
high value output capacitors are used, such as 1000µF to 5000µF
and the V

pin is instantaneously shorted to ground, damage
can occur. A diode from output to input is recommended, when a
crowbar circuit at the input of the AMS1503 is used (Figure 6).
Normal power supply cycling or even plugging and unplugging in
the system will not generate current large enough to do any
damage.

V

CONTROL

V

POWER

+

CONTROL

POWER OUTPUT

+

AMS1503

ADJ

SENSE

D2*D1*

R1

R2

V

+

OUT

Thermal resistance specification for both the Control Section and
the Power Transistor are given in the electrical characteristics.
The thermal resistance of the Control section is given as

0.65°C/W and junction temperature of the Control section can
run up to 125°C. The thermal resistance of the Power section is
given as 2.7°C/W and junction temperature of the Power section
can run up to 150°C. Due to the thermal gradients between the
power transistor and the control circuitry there is a significant
difference in thermal resistance between the Control and Power
sections.
Virtually all the power dissipated by the device is dissipated in
the power transistor. The temperature rise in the power transistor
will be greater than the temperature rise in the Control section
making the thermal resistance lower in the Control section. At
power levels below 12W the temperature gradient will be less
than 25°C and the maximum ambient temperature will be
determined by the junction temperature of the Control section.
This is due to the lower maximum junction temperature in the
Control section. At power levels above 12W the temperature
gradient will be greater than 25°C and the maximum ambient
temperature will be determined by the Power section. In both
cases the junction temperature is determined by the total power
dissipated in the device. For most low dropout applications the
power dissipation will be less than 12W.
The power in the device is made up of two components: the
power in the output transistor and the power in the drive circuit.
The power in the control circuit is negligible.
The power in the drive circuit is equal to:

P

= (V

DRIVE

where I
I

/58(max).

OUT

- V

CONTROL

OUT

)(I

CONTROL

is equal to between I

)

/100(typ) and

The power in the output transistor is equal to:
P

OUTPUT

= (V

POWER

-V

OUT

)(I

OUT

)

The total power is equal to:

Figure 6. Optional Clamp Diodes Protect Against

Input Crowbar Circuits

P

TOTAL

= P

DRIVE

+ P

OUTPUT

Junction-to-case thermal resistance is specified from the IC

If the AMS1503 is connected as a single supply device with the
control and power input pins shorted together the internal diode
between the output and the power input pin will protect the
control input pin. As with any IC regulator, none the protection
circuitry will be functional and the internal transistors will break
down if the maximum input to output voltage differential is
exceeded.

junction to the bottom of the case directly below the die. This is
the lowest resistance path for the heat flow. In order to ensure the
best possible thermal flow from this area of the package to the
heat sink proper mounting is required. Thermal compound at the
case-to-heat sink interface is recommended. A thermally
conductive spacer can be used, if the case of the device must be
electrically isolated, but its added contribution to thermal
resistance has to be considered.

Thermal Considerations

The AMS1503 series have internal power and thermal limiting
circuitry designed to protect the device under overload conditions.
However maximum junction temperature ratings should not be
exceeded under continuous normal load conditions. Careful
consideration must be given to all sources of thermal resistance
from junction to ambient, including junction-to-case, case-to-heat
sink interface and heat sink resistance itself.

Advanced Monolithic Systems 6680B Sierra Lane, Dublin, CA 94568 Phone [phone] Fax [phone]

TYPICAL PERFORMANCE CHARACTERISTICS

AMS1503

Control Pin Current vs
Output Current Minimum Control Voltage

140
120

100

80

60
40

20

CONTROL PIN CURRENT (mA)

0

0 1 2

OUTPUT CURRENT (A)

TYPICAL

DEVICE

3 0

2

)(V)

OUT

1

- V

CONTROL

(V

MINMUM CONTROL VOLTAGE

0

Reference Voltage vs
Temperature

1.258

1.256

1.254

1.252

1.250

1.248

1.246

REFERENCE VOLTAGE (V)

1.244

1.242

-25 0 25 50 75 100 125 150

-50
TEMPERATURE (° C)

TJ = 25° CTJ = 125° C

1

OUTPUT CURRENT (A)

2 3 0 1 2 3

V

OUT

50µV/DIV

LOAD

400mA

Dropout Voltage ­Minimum Power Voltage

1.0

0.5

TJ = 125° C

TJ = 25° C

MINIMUM POWER VOLTAGE

0

OUTPUT CURRENT (A)

Load Current Step Response

3A

50µ/DIV

Advanced Monolithic Systems 6680B Sierra Lane, Dublin, CA 94568 Phone [phone] Fax [phone]

PACKAGE DIMENSIONS inches (millimeters) unless otherwise noted.

5 LEAD TO-220 PLASTIC PACKAGE (T)

AMS1503

(11.684-12.700)

0.980-1.070

(24.892-27.178)

0.460-0.500

0.520-0.570

(13.208-14.478)

0.062-0.072

(1.570-1.830)

0.387-0.413
(9.83-10.49)

0.149-0.153
(3.77-3.87)

0.240-0.260

(6.100-6.600)

0.335-0.345
(8.51-8.77)

0.032
(0.81)

DIA

0.575-0.605

(14.61-15.37)

TYP

0.170-0.190
(4.32-4.82)

0.013-0.023

(0.330-0.584)

5 LEAD TO-263 PLASTIC PACKAGE (M)

0.045-0.055

(1.143-1.397)

0.105

TYP

(2.67)

T (TO-220 ) AMS DRW# 042194

0.165-0.180

(4.191-4.572)

0.108

(2.74)

TYP

0.013-0.023

(0.330-0.584)

0.045-0.055

(1.143-1.397)

+0.008

0.004

-0.004

+0.203

(

0.102

-0.102

0.095-0.115

(2.413-2.921)

0.90-0.110

(2.29-2.79)

M (DD5) AMS DRW#042192R1

)

0.057-0.077

(1.447-1.955)

0.390-0.415

(9.906-10.541)

0.060

(1.524)

TYP

0.330-0.370

(8.382-9.398)

0.199-0.218
(5.05-5.54 )

0.032
(0.81)

TYP

Advanced Monolithic Systems 6680B Sierra Lane, Dublin, CA 94568 Phone [phone] Fax [phone]

PACKAGE DIMENSIONS inches (millimeters) unless otherwise noted (Continued).

7 LEAD TO-220 PLASTIC PACKAGE (T)

AMS1503

(11.684-12.700)

0.980-1.070

(24.892-27.178)

0.460-0.500

0.520-0.620

(13.208-14.224)

0.040-0.060

(1.016-1.524)

0.390-0.415

(9.906-10.541)

0.147-0.155

(3.734-3.937)

0.230-0.270

(5.842-6.858)

0.330-0.370
(8.382-9.398)

0.026-0.036

(0.660-0.914)

DIA

0.570-0.620

(14.478-15.748)

0.165-0.180

(4.191-4.572)

0.013-0.023

(0.330-0.584)

0.045-0.055

(1.143-1.397)

0.095-0.115

(2.413-2.921)

T (TO-220 ) AMS DRW# 042291

Advanced Monolithic Systems 6680B Sierra Lane, Dublin, CA 94568 Phone [phone] Fax [phone]