CMOS
a
FEATURES
80 MHz Pipelined Operation
10-Bit D/A Converters
RS-343A/RS-170 Compatible Outputs
TTL Compatible Inputs
+5 V CMOS Monolithic Construction
28-Pin SOIC Package
APPLICATIONS
High Definition Television (HDTV)
High Resolution Color Graphics
Digital Radio Modulation
CAE/CAD/CAM Applications
Image Processing
Instrumentation
Video Signal Reconstruction
Direct Digital Synthesis (DDS) & I/O Modulation
Wireless LAN
Wireless Local Loop
SPEED GRADES
80 MHz
50 MHz
30 MHz
CLOCK
80 MHz, 10-Bit Video DAC
ADV7128
FUNCTIONAL BLOCK DIAGRAM
V
AA
ADV7128
D0
D9
10
GND
FS
ADJUST
DATA
REGISTER
V
REF
REFERENCE
AMPLIFIER
10
DAC
COMP
I
OUT
GENERAL DESCRIPTION
The ADV7128 (ADV) is a video speed, digital-to-analog converter on a single monolithic chip. It consists of a high speed,
10-bit, video D/A converters; a standard TTL input interface;
and a high impedance, analog output, current source.
The ADV7128 has a 10-bit pixel input port. A single +5 V
power supply, an external 1.23 V reference and pixel clock input
are and all that are required to make the part operational.
The ADV7128 is capable of generating video output signals
which are compatible with RS-343A, RS-170 and most proposed production system HDTV video standards, including
SMPTE 240M.
The ADV7128 is fabricated in a +5 V CMOS process. Its
monolithic CMOS construction ensures greater functionality
with low power dissipation. The ADV7128 is available in a 28lead small outline IC (SOIC).
ADV is a registered trademark of Analog Devices, Inc.
PRODUCT HIGHLIGHTS
1. Fast video refresh rate, 80 MHz.
2. Guaranteed monotonic to 10 bits. Ten bits of resolution allows for implementation of linearization functions such as
gamma correction and contrast enhancement.
3. Compatible with a wide variety of high resolution color
graphics systems including RS-343A/RS-170 and the proposed SMPTE 240M standard for HDTV.
4. Combined with a numerically controlled oscillator (AD9955),
it forms a complete frequency synthesizer (DDS).
5. Using the parts reduced power output DAC modes, it is
ideal for power and cost sensitive communications type
applications.
REV. 0
Information furnished by Analog Devices is believed to be accurate and
reliable. However, no responsibility is assumed by Analog Devices for its
use, nor for any infringements of patents or other rights of third parties
which may result from its use. No license is granted by implication or
otherwise under any patent or patent rights of Analog Devices.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 617/329-4700 Fax: 617/326-8703
ADV7128–SPECIFICA TIONS
(VAA = +5 V 6 5%; V
All specifications T
= +1.235 V; RL = 37.5 V, CL = 10 pF; R
REF
1
to T
MIN
unless otherwise noted.)
MAX
= 560 V.
SET
Parameter K Version Units Test Conditions/Comments
STATIC PERFORMANCE
Resolution 10 Bits
Accuracy
Integral Nonlinearity, INL ±1 LSB max
Differential Nonlinearity, DNL ±1 LSB max Guaranteed Monotonic
Gray Scale Error ±5 % Gray Scale max Max Gray Scale Current = (V
* 7,969/R
REF
SET
) mA
Coding Binary
DIGITAL INPUTS
Input High Voltage, V
Input Low Voltage, V
Input Current, I
Input Capacitance, C
INL
IN
IN
INH
2
2 V min
0.8 V max
±1 µA max VIN = 0.4 V or 2.4 V
10 pF max
ANALOG OUTPUT
Gray Scale Current Range 15 mA min
22 mA max
Output Current
White Level 16.74 mA min Typically 17.62 mA
18.50 mA max
Black Level 0 µA min Typically 5 µA
50 µA max
LSB Size 17.28 µA typ
Output Compliance, V
Output Impedance, R
OC
OUT
Output Capacitance, C
OUT
2
2
0 V min
+1.4 V max
100 kΩ typ
30 pF max I
OUT
= 0 mA
VOLTAGE REFERENCE
Voltage Reference Range, V
Input Current, I
VREF
REF
1.14/1.26 V min/V max V
–5 mA typ
= 1.235 V for Specified Performance
REF
POWER REQUIREMENTS
V
AA
I
AA
Power Supply Rejection Ratio
2
5 V nom
125 mA max Typically 80 mA: 80 MHz Parts
100 mA max Typically 70 mA: 50 MHz & 35 MHz Parts
0.5 %/% max Typically 0.12%/%: f = 1 kHz, COMP = 0.1 µF
Power Dissipation 625 mW max Typically 400 mW: 80 MHz Parts
500 mW max Typically 350 mW: 50 MHz & 30 MHz Parts
DYNAMIC PERFORMANCE
Glitch Impulse
DAC Noise
NOTES
1
Temperature range (T
2
Sample tested at +25°C to ensure compliance.
3
TTL input values are 0 to 3 volts, with input rise/fall times ≤3 ns, measured between the 10% and 90% points. Timing reference points at 50% for inputs and
outputs. See timing notes in Figure 1.
4
This includes effects due to clock and data feedthrough.
Specifications subject to change without notice.
2, 3, 4
2, 3
MIN
to T
MAX
50 pV secs typ
200 pV secs typ
); 0°C to +70°C.
–2–
REV. 0
ADV7128
TIMING CHARACTERISTICS
(VAA = +5 V 6 5%; V
1
All specifications T
= +1.235 V; RL = 37.5 V, CL = 10 pF; R
REF
2
to T
MIN
unless otherwise noted.)
MAX
= 560 V.
SET
Parameter 80 MHz Version 50 MHz Version 30 MHz Version Units Conditions/Comments
f
MAX
t
1
t
2
t
3
t
4
t
5
t
6
80 50 30 MHz max Clock Rate
3 6 8 ns min Data & Control Setup Time
2 2 2 ns min Data & Control Hold Time
12.5 20 33.3 ns min Clock Cycle Time
4 7 9 ns min Clock Pulse Width High Time
4 7 9 ns min Clock Pulse Width Low Time
30 30 30 ns max Analog Output Delay
20 20 20 ns typ
t
7
3
t
8
NOTES
1
TTL input values are 0 to 3 volts, with input rise/fall times ≤3 ns, measured between the 10% and 90% points. Timing reference points at 50% for inputs
and outputs. See timing notes in Figure 1.
2
Temperature range (T
3
Sample tested at +25°C to ensure compliance.
Specifications subject to change without notice.
3 3 3 ns max Analog Output Rise/Fall Time
12 15 15 ns typ Analog Output Transition Time
to T
MIN
): 0°C to +70°C
MAX
CLOCK
t
t
4
5
t
3
t
t
1
2
DIGITAL INPUTS
D0–D9
ANALOG OUTPUTS
NOTES
1. OUTPUT DELAY (
POINT OF FULL-SCALE TRANSITION.
2. TRANSITION TIME (
FINAL OUTPUT VALUE.
3. OUTPUT RISE/FALL TIME (
(I
)
OUT
t
) MEASURED FROM THE 50% POINT OF THE RISING EDGE OF THE CLOCK TO THE 50%
6
t
) MEASURED FROM THE 50% POINT OF FULL-SCALE TRANSITION TO WITHIN 2% OF THE
8
t
) MEASURED BETWEEN THE 10% AND 90% POINTS OF FULL-SCALE TRANSITION.
7
Figure 1. Video Input/Output Timing
RECOMMENDED OPERATING CONDITIONS
Parameter Symbol Min Typ Max Units
Power Supply V
AA
4.75 5.00 5.25 Volts
Ambient Operating
Temperature T
Output Load R
Reference Voltage V
A
L
REF
0 +70 °C
37.5 Ω
1.14 1.235 1.26 Volts
DATA
t
t
8
6
t
7
ORDERING GUIDE
Accuracy Temperature Package
Model Speed DNL INL Range Option*
ADV7128KR80 80 MHz ±1 ±10°C to +70°C R-28
ADV7128KR50 50 MHz ±1 ±10°C to +70°C R-28
ADV7128KR30 30 MHz ±1 ±10°C to +70°C R-28
*R = SOIC.
REV. 0
–3–
ADV7128
ABSOLUTE MAXIMUM RATINGS
*
PIN CONFIGURATION
VAA to GND . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .+7 V
Voltage on Any Digital Pin . . . . . . GND –0.5 V to V
Ambient Operating Temperature (T
Storage Temperature (T
Junction Temperature (T
) . . . . . . . . . . . . . . . –65°C to +150°C
S
) . . . . . . . . . . . . . . . . . . . . . +150°C
J
) . . . . . . . . 0°C to +70°C
A
Lead Temperature (Soldering, 10 secs) . . . . . . . . . . . . +300°C
Vapor Phase Soldering (2 minutes) . . . . . . . . . . . . . . . +220°C
I
to GND1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0 V to V
OUT
NOTES
*
Stresses above those listed under “Absolute Maximum Ratings” may cause
permanent damage to the device. This is a stress rating only and functional
operation of the device at these or any other conditions above those listed in the
operational sections of this specification is not implied. Exposure to absolute
maximum rating conditions for extended periods may affect device reliability.
1
Analog Output Short Circuit to any Power Supply or Common can be of an
indefinite duration.
+0.5 V
AA
AA
V
1
AA
D0
2
3
D1
4
D2
5
D3
6
D4
ADV7128
7
D5
D6
D7
D8
D9
V
AA
V
AA
V
AA
8
9
10
11
12
13
14
TOP VIEW
(Not to Scale)
CAUTION
ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily
accumulate on the human body and test equipment and can discharge without detection.
Although the ADV7128 features proprietary ESD protection circuitry, permanent damage may
occur on devices subjected to high energy electrostatic discharges. Therefore, proper ESD
precautions are recommended to avoid performance degradation or loss of functionality.
28
V
AA
V
27
AA
V
26
AA
25
R
SET
24
V
REF
23
COMP
V
22
AA
I
21
OUT
20
V
AA
19
GND
18
GND
17
CLOCK
16
V
AA
V
15
AA
WARNING!
ESD SENSITIVE DEVICE
PIN FUNCTION DESCRIPTION
Pin
Mnemonic Function
CLOCK Clock input (TTL compatible). The rising edge of CLOCK latches the R0–R9, G0–G9, B0–B9, SYNC and
BLANK pixel and control inputs. It is typically the pixel clock rate of the video system. CLOCK should be driven
by a dedicated TTL buffer.
D0–D9 Data inputs (TTL compatible). Data is latched on the rising edge of CLOCK. D0 is the least significant data bit.
Unused data inputs should be connected to either the regular PCB power or ground plane.
I
OUT
Current output. This high impedance current source is capable of directly driving a doubly terminated 75 Ω
coaxial cable.
R
SET
Full-scale adjust control. A resistor (R
SET
) connected between this pin and GND, controls the magnitude of the
full-scale video signal. Note that the IRE relationships are maintained, regardless of the full-scale output current.
The relationship between R
I
(mA) = 7,969 3 V
OUT
and the full-scale output current on I
SET
REF
(V)/R
SET
(Ω)
is given by:
OUT
COMP Compensation pin. This is a compensation pin for the internal reference amplifier. A 0.1 µF ceramic capacitor
must be connected between COMP and VAA.
V
REF
Voltage reference input. An external 1.23 V voltage reference must be connected to this pin. The use of an external resistor divider network is not recommended. A 0.1 µF decoupling ceramic capacitor should be connected be-
tween V
V
AA
Analog power supply (5 V ± 5%). All VAA pins on the ADV7128 must be connected.
and VAA.
REF
GND Ground. All GND pins must be connected.
–4–
REV. 0
ADV7128
TERMINOLOGY
Color Video (RGB)
This usually refers to the technique of combining the three primary colors of red, green and blue to produce color pictures
within the usual spectrum. In RGB monitors, three DACs are
required, one for each color.
Gray Scale
The discrete levels of video signal between reference black and
reference white levels. A 10-bit DAC contains 1024 different
levels, while an 8-bit DAC contains 256.
Raster Scan
The most basic method of sweeping a CRT one line at a time to
generate and display images.
CIRCUIT DESCRIPTION AND OPERATION
The ADV7128 contains one 10-bit D/A converter, with one input channel containing a 10-bit register. Also integrated on
board the part is a reference amplifier.
Digital Inputs
Ten bits of data (color information) D0–D9 are latched into the
device on the rising edge of each clock cycle. This data is presented to the 10-bit DAC and is then converted to an analog
output waveform. See Figure 2.
CLOCK
DIGITAL
INPUTS
D0–D9
DATA
Reference Black Level
The maximum negative polarity amplitude of the video signal.
Reference White Level
The maximum positive polarity amplitude of the video signal.
Video Signal
That portion of the composite video signal which varies in gray
scale levels between reference white and reference black. Also
referred to as the picture signal, this is the portion which may be
visually observed.
If we, therefore, have a graphics system with a 1024 × 1024
resolution, a noninterlaced 60 Hz refresh rate and a retrace factor of 0.8, then:
Dot Rate = 1024 × 1024 × 60/0.8
= 78.6 MHz
The required CLOCK frequency is thus 78.6 MHz.
All video data and control inputs are latched into the ADV7128
on the rising edge of CLOCK, as previously described in the
“Digital Inputs” section. It is recommended that the CLOCK
input to the ADV7128 be driven by a TTL buffer (e.g.,
74F244).
I
OUT
mA V
17.61 0.66
WHITE
LEVEL
ANALOG
OUTPUTS
I
OUT
Figure 2. Video Data Input/Output
All these digital inputs are specified to accept TTL logic levels.
Clock Input
The CLOCK input of the ADV7128 is typically the pixel clock
rate of the system. It is also known as the dot rate. The dot rate,
and hence the required CLOCK frequency, will be determined
by the on-screen resolution, according to the following
equation:
Dot Rate = (Horiz Res)
×
(Vert Res) × (Refresh Rate)/
(Retrace Factor)
Horiz Res = Number of Pixels/Line.
Vert Res = Number of Lines/Frame.
Refresh Rate = Horizontal Scan Rate. This is the rate at
which the screen must be refreshed, typically 60 Hz for a noninterlaced system or
30 Hz for an interlaced system.
Retrace Factor = Total Blank Time Factor. This takes into
account that the display is blanked for a
certain fraction of the total duration of
each frame (e.g., 0.8).
100
IRE
0 0
NOTES
1. OUTPUTS CONNECTED TO A DOUBLY TERMINATED 75Ω LOAD.
= 1.235V, R
2. V
REF
3. RS–343A LEVELS AND TOLERANCES ASSUMED ON ALL LEVELS.
= 560Ω.
SET
Figure 3. I
Video Output Waveform
OUT
Table I. Video Output Truth Table for the ADV7128
Description I
OUT
1
DAC Input Data
WHITE LEVEL 17.62 3FF
VIDEO video data
VIDEO to BLACK video data
BLACK LEVEL 0 00H
NOTE
1
Typical with full scale = 17.62 mA. V
= 1.235 V, R
REF
= 560 Ω.
SET
BLACK
LEVEL
REV. 0
–5–
ADV7128
Reference Input
An external 1.23 V voltage reference is required to drive the
ADV7128. The AD589 from Analog Devices is an ideal choice
of reference. It is a two-terminal, low cost, temperature compensated bandgap voltage reference which provides a fixed
1.23 V output voltage for input currents between 50 µA and
5 mA. Figure 4 shows a typical reference circuit connection diagram. The voltage reference gets its current drive from the
ADV7128’s V
through an on-board 1 kΩ resistor to the V
AA
REF
pin. A 0.1 µF ceramic capacitor is required between the COMP
pin and V
. This is necessary so as to provide compensation for
AA
the internal reference amplifier.
A resistance R
connected between R
SET
and GND deter-
SET
mines the amplitude of the output video level according to the
following equation:
I
(mA) = 7,969 × V
OUT
Using a variable value of R
REF
(V)/R
SET
(Ω) (1)
SET
, as shown in Figure 4, allows for
accurate adjustment of the analog output video levels. Use of a
fixed 560 Ω R
resistor yields the analog output levels as
SET
quoted in the specification page. These values typically correspond to the RS-343A video waveform values as shown in
Figure 3.
ANALOG POWER PLANE
AA
REF
R
560Ω
SET
5V+
~
I
5mA
~
REF
AD589
500Ω
100Ω
(1.235V
VOLTAGE
REFERENCE)
COMP
TO DAC
*ADDITIONAL CIRCUITRY, INCLUDING DECOUPLING COMPONENTS,
EXCLUDED FOR CLARITY
0.01µF
ADV7128
V
1kΩ
V
RSET
GND
Figure 4. Reference Circuit
D/A Converter
The ADV7128 contains a 10-bit D/A converter. The DAC is
designed using an advanced, high speed, segmented architecture. The bit currents corresponding to each digital input are
routed to either the analog output (bit = “1”) or GND (bit =
“0”) by a sophisticated decoding scheme. The use of identical
current sources in a monolithic design guarantees monotonicity
and low glitch. The on-board operational amplifier stabilizes the
full-scale output current against temperature and power supply
variations.
Analog Output
The analog output of the ADV7128 is a high impedance current
source. The current output is capable of directly driving a
37.5 Ω load, such as a doubly terminated 75 Ω coaxial cable.
Figure 5a shows the required configuration for the output connected into a doubly terminated 75 Ω load. This arrangement
will develop RS-343A video output voltage levels across a 75 Ω
monitor.
I
OUT
DAC
ZS = 75Ω
(SOURCE
TERMINATION)
ZO = 75Ω
(CABLE)
ZL= 75Ω
(MONITOR)
Figure 5a. Analog Output Termination for RS-343A
A suggested method of driving RS-170 video levels into a 75 Ω
monitor is shown in Figure 5b. The output current level of the
DAC remains unchanged, but the source termination resistance,
Z
, on the DAC is increased from 75 Ω to 150 Ω.
S
I
OUT
DAC
= 150Ω
Z
S
(SOURCE
TERMINATION)
ZO = 75Ω
(CABLE)
ZL= 75Ω
(MONITOR)
Figure 5b. Analog Output Termination for RS-170
More detailed information regarding load terminations for various output configurations, including RS-343A and RS-170, is
available in an Application Note entitled “Video Formats & Required Load Terminations” available from Analog Devices,
publication no. E1228-15-1/89.
Figure 3 shows the video waveforms associated with the current
output driving the doubly terminated 75 Ω load of Figure 5a.
Gray Scale Operation
The ADV7128 can be used for stand-alone, gray scale (monochrome) or composite video applications (i.e., only one channel
used for video information).
Video Output Buffer
The ADV7128 is specified to drive transmission line loads,
which is what most monitors are rated as. The analog output
configurations to drive such loads are described in the Analog
Interface section and illustrated in Figure 5. However, in some
applications it may be required to drive long “transmission line”
cable lengths. Cable lengths greater than 10 meters can attenuate and distort high frequency analog output pulses. The inclusion of output buffers will compensate for some cable distortion.
Buffers with large full power bandwidths and gains between 2
and 4 will be required. These buffers will also need to be able to
supply sufficient current over the complete output voltage
swing. Analog Devices produces a range of suitable op amps for
such applications. These include the AD84x series of monolithic
op amps. In very high frequency applications (80 MHz), the
AD9617 is recommended. More information on line driver buffering circuits is given in the relevant op amp data sheets.
Use of buffer amplifiers also allows implementation of other
video standards besides RS-343A and RS-170. Altering the gain
components of the buffer circuit will result in any desired
video level.
–6–
REV. 0
ADV7128
Z
2
I
DAC
ZS = 75Ω
(SOURCE
TERMINATION)
2
OUT
3
+V
AD848
–V
Z
1
0.1µF
S
Z
1
Z
2
Z O = 75Ω
(CABLE)
ZL= 75Ω
(MONITOR)
7
6
4
0.1µF
S
75Ω
GAIN (G) = 1+
Figure 6. AD848 As an Output Buffer
PC Board Layout Considerations
The ADV7128 is optimally designed for lowest noise performance, both radiated and conducted noise. To complement the
excellent noise performance of the ADV7128 it is imperative
that great care be given to the PC board layout. Figure 7 shows
a recommended connection diagram for the ADV7128.
The layout should be optimized for lowest noise on the
ADV7128 power and ground lines. This can be achieved by
shielding the digital inputs and providing good decoupling. The
lead length between groups of V
and GND pins should be
AA
minimized so as to minimize inductive ringing.
Ground Planes
The ADV7128 and associated analog circuitry, should have a
separate ground plane referred to as the analog ground plane.
This ground plane should connect to the regular PCB ground
plane at a single point through a ferrite bead, as illustrated in
Figure 7. This bead should be located as close as possible
(within 3 inches) to the ADV7128.
The analog ground plane should encompass all ADV7128
ground pins, voltage reference circuitry, power supply bypass
circuitry, the analog output traces and any output amplifiers.
The regular PCB ground plane area should encompass all the
digital signal traces, excluding the ground pins, leading up to
the ADV7128.
Power Planes
The PC board layout should have two distinct power planes,
one for analog circuitry and one for digital circuitry. The analog
power plane should encompass the ADV7128 (V
) and all as-
AA
sociated analog circuitry. This power plane should be connected
to the regular PCB power plane (V
) at a single point through
CC
a ferrite bead, as illustrated in Figure 7. This bead should be located within three inches of the ADV7128.
The PCB power plane should provide power to all digital logic
on the PC board, and the analog power plane should provide
power to all ADV7128 power pins, voltage reference circuitry
and any output amplifiers.
The PCB power and ground planes should not overlay portions
of the analog power plane. Keeping the PCB power and ground
planes from overlaying the analog power plane will contribute to
a reduction in plane-to-plane noise coupling.
Supply Decoupling
Noise on the analog power plane can be further reduced by the
use of multiple decoupling capacitors. (See Figure 7.)
Optimum performance is achieved by the use of 0.1 µF ceramic
capacitors. Each of the two groups of V
should be individually
AA
decoupled to ground. This should be done by placing the capacitors as close as possible to the device with the capacitor
leads as short as possible, thus minimizing lead inductance.
VIDEO
DATA
INPUTS
COMP
V
D0
D9
V
REF
ADV7128
GND
RSET
CLOCK
I
AA
OUT
C6
0.1µF
ANALOG POWER PLANE
L1 (FERRITE BEAD)
C2
10µF
L2 (FERRITE BEAD)
VIDEO
OUTPUT
C1
33µF
COMPONENT
C3, C4, C5,C6
L1, L2
R
SET
+5V (V )
CC
GROUND
DESCRIPTION
33µF TANTALUM CAPACITOR
C1
10µF TANTALUM
C2
0.1µF CERAMIC CAPACITOR
FERRITE BEAD
75Ω 1% METAL FILM RESISTOR
R1
560Ω 1% METAL FILM RESISTOR
Z1
1.235V VOLTAGE REFERENCE
R
SET
560Ω
C3
0.1µF
75Ω
C4
0.1µF
R1
C5
0.1µF
Z1
(AD589)
ANALOG GROUND PLANE
Figure 7. ADV7128 Typical Connection Diagram and Component List
VENDOR PART NUMBER
FAIR-RITE 274300111 OR
MURATA BL01/02/03
DALE CMF-55C
DALE CMF-55C
ANALOG DEVICES AD589JH
REV. 0
–7–
ADV7128
It is important to note that while the ADV7128 contains circuitry to reject power supply noise, this rejection decreases with
frequency. If a high frequency switching power supply is used,
the designer should pay close attention to reducing power supply noise. A dc power supply filter (Murata BNX002) will provide EMI suppression between the switching power supply and
the main PCB. Alternatively, consideration could be given to
using a three terminal voltage regulator.
Digital Signal Interconnect
The digital signal lines to the ADV7128 should be isolated as
much as possible from the analog outputs and other analog circuitry. Digital signal lines should not overlay the analog power
plane.
Due to the high clock rates used, long clock lines to the
ADV7128 should be avoided so as to minimize noise pickup.
Any active pull-up termination resistors for the digital inputs
should be connected to the regular PCB power plane (V
CC
), and
not the analog power plane.
OUTLINE DIMENSIONS
Dimensions shown in inches and (mm).
SOIC (R-28)
Analog Signal Interconnect
The ADV7128 should be located as close as possible to the output connectors thus minimizing noise pickup and reflections
due to impedance mismatch.
The video output signals should overlay the ground plane, and
not the analog power plane, thereby maximizing the high frequency power supply rejection.
For optimum performance, the analog outputs should each have
a source termination resistance to ground of 75 Ω (doubly terminated 75 Ω configuration). This termination resistance should
be as close as possible to the ADV7128 so as to minimize
reflections.
Additional information on PCB design is available in an application note entitled “Design and Layout of a Video Graphics System for Reduced EMI.” This application note is available from
Analog Devices, publication number E1309-15-10/89.
C1760–24–1/93
0.299 (7.60)
0.291 (7.40)
PIN 1
0.011 (0.30)
0.004 (0.10)
0.019 (0.49)
0.014 (0.35)
15
14
0.419 (10.65)
0.394 (10.00)
0.104 (2.65)
0.093 (2.35)
0.012 (0.32)
0.009 (0.23)
0.05 (1.27)
0.016 (0.40)
PRINTED IN U.S.A.
28
1
0.712 (18.10)
0.697 (17.70)
0.050 (1.27)
BSC
–8–
REV. 0
Loading...