Datasheet ADP5037 Datasheet (ANALOG DEVICES)

Dual 3 MHz, 800 mA Buck

Data Sheet

FEATURES

Main input voltage range: 2.3 V to 5.5 V
Two 800 mA buck regulators and two 300 mA LDOs
24-lead, 4 mm × 4 mm LFCSP package
Regulator accuracy: ±3%
Factory programmable or external adjustable VOUTx
3 MHz buck operation with forced PWM and auto PWM/PSM

modes
BUCK1/BUCK2: output voltage range from 0.8 V to 3.8 V
LDO1/LDO2: output voltage range from 0.8 V to 5.2 V
LDO1/LDO2: input supply voltage from 1.7 V to 5.5 V
LDO1/LDO2: high PSRR and low output noise

APPLICATIONS

Power for processors, ASICS, FPGAs, and RF chipsets
Portable instrumentation and medical devices
Space constrained devices

GENERAL DESCRIPTION

The ADP5037 combines two high performance buck regulators
and two low dropout (LDO) regulators in a small, 24-lead 4 mm ×

Regulators with Two 300 mA LDOs

ADP5037

4 mm LFCSP to meet demanding performance and board space
requirements.

The high switching frequency of the buck regulators enables tiny
multilayer external components and minimizes the board space.
When the MODE pin is set high, the buck regulators operate in
forced PWM mode. When the MODE pin is set low and the
load is above a predefined threshold, the buck regulators
operate in PWM mode. When the load current falls below a
predefined threshold, the regulator operates in power save
mode (PSM), improving the light-load efficiency.

The two bucks operate out of phase to reduce the input capaci­tor requirement. The low quiescent current, low dropout voltage,
and wide input voltage range of the ADP5037 LDOs extend the
battery life of portable devices. The ADP5037 LDOs maintain
power supply rejection greater than 60 dB for frequencies as
high as 10 kHz while operating with a low headroom voltage.

Regulators in the ADP5037 are activated though dedicated
enable pins. The default output voltages can be externally set in
the adjustable version or factory programmable to a wide range
of preset values in the fixed voltage version.

TYPICAL APPLICATION CIRCUIT

AVIN

0.1µF

C1

4.7µF

C2

ON

1µF

ON

1µF

AVIN

VIN1

EN1

VIN2

EN2

EN3

VIN3

C3

EN4

VIN4

C4

C

2.3V TO

5.5V

OFF

4.7µF

1.7V TO

5.5V

OFF

HOUSEKEEPING

EN1

EN2

EN3

(ANALOG)

EN4

(DIGITAL)

ADP5037

BUCK1

MODE

MODE

BUCK2

LDO1

LDO2

AGND

Figure 1.

VOUT1

SW1
FB1

PGND1

MODE
VOUT2

SW2
FB2

PGND2
VOUT3

FB3

VOUT4
FB4

L1 1µH

R1

R2

PWM

L2 1µH

R3

R4

R5

R6

R7

R8

C5
10µF

PSM/PWM

C6
10µF

C7
1µF

C8
1µF

V

OUT1

800mA

V

OUT2

800mA

V

OUT3

300mA

V

OUT4

300mA

AT

AT

AT

AT

09887-001

Rev. A

Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registered trademarks are the property of their respective owners.

One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: [phone] www.analog.com
Fax: [phone] ©2011-2012 Analog Devices, Inc. All rights reserved.

ADP5037 Data Sheet

TABLE OF CONTENTS

Features .............................................................................................. 1

Applications ....................................................................................... 1 

General Description ......................................................................... 1

Typical Application Circuit ............................................................. 1

Revision History ............................................................................... 2

Specifications ..................................................................................... 3

General Specifications ................................................................. 3

BUCK1 and BUCK2 Specifications ........................................... 4

LDO1 and LDO2 Specifications ................................................. 4

Input and Output Capacitor, Recommended Specifications .. 5

Absolute Maximum Ratings ............................................................ 6

Thermal Resistance ...................................................................... 6

ESD Caution .................................................................................. 6

Pin Configuration and Function Descriptions ............................. 7

Typical Performance Characteristics ............................................. 8

Power Dissipation and Thermal Considerations ....................... 15

Buck Regulator Power Dissipation .......................................... 15

Junction Temperature ................................................................ 16

Theory of Operation ...................................................................... 17

Power Management Unit ........................................................... 17

BUCK1 and BUCK2 .................................................................. 19

LDO1 and LDO2 ........................................................................ 20

Applications Information .............................................................. 21

Buck External Component Selection ....................................... 21

LDO External Component Selection ...................................... 23

PCB Layout Guidelines .................................................................. 24

Typical Application Schematics .................................................... 25

Bill of Materials ............................................................................... 26

Outline Dimensions ....................................................................... 27

Ordering Guide .......................................................................... 27

REVISION HISTORY

1/12—Rev. 0 to Rev. A

Changes to Features Section and Figure 1 ..................................... 1

Changes to Table 2 and Table 3 ....................................................... 4

Changes to Table 4 ............................................................................ 5

Changes to Table 5 ............................................................................ 6

Changes to Table 7 ............................................................................ 7

Changes to Figure 34 ...................................................................... 13

Changes to Buck Regulator Power Dissipation Section ............ 15

Changes to Undervoltage Lockout Section ................................. 18

Changes to LDO1 and LDO2 Section ......................................... 20

Changes to Table 9 .......................................................................... 22

Changes to Figure 52 and Figure 53 ............................................. 25

Changes to Ordering Guide .......................................................... 27

8/11—Revision 0: Initial Version

Rev. A | Page 2 of 28

Data Sheet ADP5037

High UVLO Input Voltage Falling

UVLO

3.1

V

SPECIFICATIONS

GENERAL SPECIFICATIONS

V

= V

= V

AVI N

IN1

= 2.3 V to 5.5 V; V

IN2

25°C for typical specifications, unless otherwise noted.

Table 1.

Parameter Symbol Test Conditions/Comments Min Typ Max Unit

INPUT VOLTAGE RANGE V
THERMAL SHUTDOWN

Threshold TSSD TJ rising 150 °C

Hysteresis TS

START-UP TIME1

BUCK1, LDO1, LDO2 t

BUCK2 t

EN1, EN2, EN3, EN4, MODE INPUTS

Input Logic High VIH 1.1 V

Input Logic Low VIL 0.4 V

Input Leakage Current V

INPUT CURRENT

All Channels Enabled I

All Channels Disabled I

VIN1 UNDERVOLTAGE LOCKOUT

High UVLO Input Voltage Rising UVLO

Low UVLO Input Voltage Rising UVLO

Low UVLO Input Voltage Falling UVLO

1

Start-up time is defined as the time from EN1 = EN2 = EN3 = EN4 from 0 V to V

times are shorter for individual channels if another channel is already enabled. See the Typical Performance Characteristics section for more information.

IN3

= V

= 1.7 V to 5.5 V; TJ = −40°C to +125°C for minimum/maximum specifications, and TA =

IN4

, V

, V

AVIN

SD-HYS

STA RT1

STA RT2

I-LEAKAGE

STBY-NOSW

SHUTDOWN

2.3 5.5 V

IN1

IN2

20 °C

250 µs
300 µs

0.05 1 µA

No load, no buck switching 108 175 µA

TJ = −40°C to +85°C 0.3 1 µA

3.9 V

VIN1RISE

VI N1 FAL L

2.275 V

VIN1RISE

1.95 V

VIN1FA LL

to VOUT1, VOUT2, VOUT3, and VOUT4 reaching 90% of their nominal level. Start-up

AVIN

Rev. A | Page 3 of 28

ADP5037 Data Sheet

VOLTAGE FEEDBACK

V

, V

Models with adjustable outputs

0.485

0.5

0.515

V

Current Limit

I

, I

pFET switch peak current limit

1200

1550

1900

mA

Load Regulation3

(∆V

)/∆I

,

I

= I

= 1 mA to 300 mA

0.001

0.003

%/mA

BUCK1 AND BUCK2 SPECIFICATIONS

V

= V

= V

AVI N

IN1

specifications, unless otherwise noted.

Table 2.

Parameter Symbol Test Conditions/Comments Min Typ Max Unit

OUTPUT CHARACTERISTICS

Output Voltage Accuracy ΔV

Line Regulation (∆V

Load Regulation (∆V

OPERATING SUPPLY CURRENT MODE = ground

BUCK1 Only IIN I

BUCK2 Only IIN I

BUCK1 and BUCK2 IIN I

PSM CURRENT THRESHOLD I
SW CHARACTERISTICS

SW On Resistance R
R
R
R

ACTIVE PULL-DOWN R
OSCILLATOR FREQUENCY fSW 2.5 3.0 3.5 MHz

1

All limits at temperature extremes are guaranteed via correlation using standard statistical quality control (SQC).

= 2.3 V to 5.5 V; TJ = −40°C to +125°C for minimum/maximum specifications, and TA = 25°C for typical

IN2

OUT1/VOUT1

ΔV

OUT2/VOUT2

OUT1/VOUT1

(∆V

OUT2/VOUT2

OUT1/VOUT1

(∆V

OUT2/VOUT2

FB1

1

,

PWM mode; I

LOAD1

= I

= 0 mA to 800 mA −3 +3 %

LOAD2

)/∆V

,

PWM mode −0.05 %/V

IN1

)/∆V

IN2

OUT1,

OUT2

I

= 0 mA to 800 mA, PWM mode −0.1 %/A

LOAD

= 0 mA, device not switching, all other

LOAD1

44 μA

)/∆I
)/∆I

FB2

channels disabled

= 0 mA, device not switching, all other

LOAD2

55 μA

channels disabled

= I

LOAD1

= 0 mA, device not switching,

LOAD2

67 μA

LDO channels disabled

PSM to PWM operation 100 mA

PSM

V

NFET

V

PFET

V

NFET

V

PFET

LIMIT1

LIMIT2

Channel disabled 75 Ω

PDWN-B

= V

= 3.6 V 155 240 mΩ

IN1

IN2

= V

= 3.6 V 205 310 mΩ

IN1

IN2

= V

= 5.5 V 137 204 mΩ

IN1

IN2

= V

= 5.5 V 162 243 mΩ

IN1

IN2

LDO1 AND LDO2 SPECIFICATIONS

V

= (V

IN3

1 µF; T

Table 3.

Parameter Symbol Test Conditions/Comments Min Typ Max Unit

INPUT VOLTAGE RANGE V
OPERATING SUPPLY CURRENT

Bias Current per LDO2 I
I
I

Total System Input Current

LDO1 or LDO2 Only I
LDO1 and LDO2 Only I

OUTPUT CHARACTERISTICS

Output Voltage Accuracy

Line Regulation (∆V

+ 0.5 V) or 1.7 V (whichever is greater) to 5.5 V, V

OUT3

= −40°C to +125°C for minimum/maximum specifications, and TA = 25°C for typical specifications, unless otherwise noted.1

J

, V

1.7 5.5 V

IN3

IN4

VIN3BIAS/IVIN4BIAS

IIN

I

OUT3

OUT3

OUT3

Includes all current into AVIN, VIN1, VIN2, VIN3,

= (V

IN4

= I

= 0 µA 10 30 µA

OUT4

= I

= 10 mA 60 100 µA

OUT4

= I

= 300 mA 165 245 µA

OUT4

+ 0.5 V) or 1.7 V (whichever is greater) to 5.5 V; CIN = C

OUT4

and VIN4

= I

OUT3

OUT3

= 0 µA, all other channels disabled 53 µA

OUT4

= I

= 0 µA, buck channels disabled 74 µA

OUT4

ΔV

OUT3/VOUT3

ΔV

OUT4/VOUT4

OUT3/VOUT3

(∆V

OUT4/VOUT4

OUT3/VOUT3

(∆V

OUT4/VOUT4

,

)/∆V
)/∆V

)/∆I

IN3

IN4

OUT3

OUT4

,

100 µA < I

I

= I

OUT3

OUT4

OUT3

OUT4

Rev. A | Page 4 of 28

< 300 mA, 100 µA < I

OUT3

< 300 mA −3 +3 %

OUT4

= 1 mA −0.03 +0.03 %/V

OUT

=

Data Sheet ADP5037

DROPOUT VOLTAGE4

V

V

= V

= 5.2 V, I

= I

= 300 mA

50 mV

100 kHz, V

= 3.3 V, V

= 2.8 V, I

= 1 mA

62 dB

BUCK1, BUCK2 Output Capacitor Ratings

C

, C

10 40

µF

Parameter Symbol Test Conditions/Comments Min Typ Max Unit

V

VOLTAGE FEEDBACK

V
V
V
CURRENT-LIMIT THRESHOLD5 I
ACTIVE PULL-DOWN R
OUTPUT NOISE

Regulator LDO1 NOISE
Regulator LDO2 NOISE

POWER SUPPLY REJECTION

RATIO
Regulator LDO1 10 kH z, V

1 MHz, V

Regulator LDO2 10 kH z, V
100 kHz, V
1 MHz, V

1

All limits at temperature extremes are guaranteed via correlation using standard statistical quality control (SQC).

2

This is the input current into VIN3/VIN4, which is not delivered to the output load.

3

Based on an endpoint calculation using 1 mA and 300 mA loads.

4

Dropout voltage is defined as the input-to-output voltage differential when the input voltage is set to the nominal output voltage. This applies only to output voltages

above 1.7 V.

5

Current-limit threshold is defined as the current at which the output voltage drops to 90% of the specified typical value. For example, the current limit for a 3.0 V

output voltage is defined as the current that causes the output voltage to drop to 90% of 3.0 V, or 2.7 V.

, V

FB3

FB4

DROPOUT

, I

LIMIT3

PDWN-L

335 600 mA

LIMIT4

Channel disabled 600 Ω

10 Hz to 100 kHz, V

LDO1

10 Hz to 100 kHz, V

LDO2

0.485 0.5 0.515 V

OUT3

OUT3

OUT3

OUT3

= V
= V
= V

OUT4

OUT4

OUT4

OUT4

= 3.3 V, I
= 2.5 V, I
= 1.8 V, I

OUT3

OUT3

OUT3

OUT3

= 5 V, V

IN3

= 5 V, V

IN4

OUT4

= I

= 300 mA 75 140 mV

OUT4

= I

= 300 mA 100 mV

OUT4

= I

= 300 mA 180 mV

OUT4

= 2.8 V 100 µV rms

OUT3

= 1.2 V 60 µV rms

OUT4

PSRR

= 3.3 V, V

IN3

IN3

= 3.3 V, V

IN3

= 1.8 V, V

IN4

= 1.8 V, V

IN4

= 1.8 V, V

IN4

OUT3

OUT3

OUT3

OUT4

OUT4

OUT4

= 2.8 V, I

= 2.8 V, I

= 1.2 V, I

= 1.2 V, I

= 1.2 V, I

= 1 mA 60 dB

OUT3

OUT3

= 1 mA 63 dB

OUT3

= 1 mA 54 dB

OUT4

= 1 mA 57 dB

OUT4

= 1 mA 64 dB

OUT4

INPUT AND OUTPUT CAPACITOR, RECOMMENDED SPECIFICATIONS

TA = −40°C to +125°C, unless otherwise specified.

Table 4.

Parameter Symbol Min Typ Max Unit

NOMINAL INPUT AND OUTPUT CAPACITOR RATINGS

BUCK1, BUCK2 Input Capacitor Ratings C

LDO1 Input and Output Capacitor Ratings C
CAPACITOR ESR R

1

The minimum input and output capacitance should be greater than 0.70 µF over the full range of operating conditions. The full range of operating conditions in the

application must be considered during device selection to ensure that the minimum capacitance specification is met. X7R- and X5R-type capacitors are recommended;
Y5V and Z5U capacitors are not recommended for use because of their poor temperature and dc bias characteristics.

, C

MIN1

MIN1

MIN3

ESR

4.7 40 µF

MIN2

MIN2

, C

1.0 µF

MIN4

0.001 1 Ω

Rev. A | Page 5 of 28

ADP5037 Data Sheet

VIN1, VIN2 to AVIN

−0.3 V to +0.3 V

VOUT3 to AGND

−0.3 V to (VIN3 + 0.3 V)

ABSOLUTE MAXIMUM RATINGS

Table 5.

Parameter Rating

AVIN to AGND −0.3 V to +6 V

THERMAL RESISTANCE

θJA is specified for the worst-case conditions, that is, a device
soldered in a circuit board for surface-mount packages.

PGND1, PGND2 to AGND −0.3 V to +0.3 V
VIN3, VIN4, VOUT1, VOUT2, FB1, FB2,

FB3, FB4, EN1, EN2, EN3, EN4,
MODE to AGND

VOUT4 to AGND −0.3 V to (VIN4 + 0.3 V)
SW1 to PGND1 −0.3 V to (VIN1 + 0.3 V)
SW2 to PGND2 −0.3 V to (VIN2 + 0.3 V)
Storage Temperature Range −65°C to +150°C
Operating Junction Temperature

Range

Soldering Conditions JEDEC J-STD-020

Stresses above those listed under Absolute Maximum Ratings
may cause permanent damage to the device. This is a stress
rating only; functional operation of the device at these or any
other conditions above those indicated in the operational
section of this specification is not implied. Exposure to absolute
maximum rating conditions for extended periods may affect
device reliability.

For detailed information on power dissipation, see the Power
Dissipation and Thermal Considerations section.

−0.3 V to (AVIN + 0.3 V)

−40°C to +125°C

Table 6. Thermal Resistance

Package Type θJA θJC Unit

24-Lead, 0.5 mm pitch LFCSP 35 3 °C/W

ESD CAUTION

Rev. A | Page 6 of 28

Data Sheet ADP5037

PIN 1
INDICATOR

NOTES

1. NC = NO CONNE C T. DO NOT CONNECT TO THIS PIN.

2. IT I S RE COMMENDED THAT THE EXPOSED PAD
BE SOLDERED TO THE GROUND PLANE.

1
2
3
4
5
6

15

16

17

18

14
13

7

8

9

11

12

10

21

22

23

24

20

19

ADP5037

TOP VIEW

(Not to S cale)

VOUT4

FB3

VOUT3

VIN3

EN3

VIN4

AGND
AVIN
VIN1
SW1
PGND1
MODE

FB4

EN4
VIN2
SW2

PGND2

NC

EN1

FB1

VOUT1

VOUT2

FB2

EN2

09887-003

11

FB1

BUCK1 Feedback Input. For device models with adjustable output voltage, connect this pin to the middle of the
EPAD (EP)

Exposed Pad. It is recommended that the exposed pad be soldered to the ground plane.

PIN CONFIGURATION AND FUNCTION DESCRIPTIONS

Figure 2. Pin Configuration—View from the Top of the Die

Table 7. Pin Function Descriptions

Pin No. Mnemonic Description

1 FB4 LDO2 Feedback Input. For device models with adjustable output voltage, connect this pin to the middle of the

LDO2 resistor divider. For device models with fixed output voltage, connect this pin to the top of the capacitor on

VOUT4.
2 EN4 LDO2 Enable Pin. High level turns on this regulator, and low level turns it off.
3 VIN2 BUCK2 Input Supply (2.3 V to 5.5 V). Connect VIN2 to VIN1 and AVIN.
4 SW2 BUCK2 Switching Node.
5 PGND2 Dedicated Power Ground for BUCK2.
6 NC No Connect. Leave this pin unconnected.
7 EN2 BUCK2 Enable Pin. High level turns on this regulator, and low level turns it off.
8 FB2 BUCK2 Feedback Input. For device models with adjustable output voltage, connect this pin to the middle of the

BUCK2 resistor divider. For device models with fixed output voltage, leave this pin unconnected.
9 VOUT2 BUCK2 Output Voltage Sensing Input. Connect VOUT2 to the top of the capacitor on VOUT2.
10 VOUT1 BUCK1 Output Voltage Sensing Input. Connect VOUT1 to the top of the capacitor on VOUT1.

BUCK1 resistor divider. For device models with fixed output voltage, leave this pin unconnected.
12 EN1 BUCK1 Enable Pin. High level turns on this regulator, and low level turns it off.
13 MODE BUCK1/BUCK2 Operating Mode. MODE = high: forced PWM operation. MODE = low: auto PWM/PSM operation.
14 PGND1 Dedicated Power Ground for BUCK1.
15 SW1 BUCK1 Switching Node.
16 VIN1 BUCK1 Input Supply (2.3 V to 5.5 V). Connect VIN1 to VIN2 and AVIN.
17 AVIN Analog Input Supply (2.3 V to 5.5 V). Connect AVIN to VIN1 and VIN2.
18 AGND Analog Ground.
19 FB3 LDO1 Feedback Input. For device models with adjustable output voltage, connect this pin to the middle of the

LDO1 resistor divider. For device models with fixed output voltage, connect this pin to the top of the capacitor on

VOUT3.
20 VOUT3 LDO1 Output Voltage.
21 VIN3 LDO1 Input Supply (1.7 V to 5.5 V).
22 EN3 LDO1 Enable Pin. High level turns on this regulator, and low level turns it off.
23 VIN4 LDO2 Input Supply (1.7 V to 5.5 V).
24 VOUT4 LDO2 Output Voltage.

Rev. A | Page 7 of 28

ADP5037 Data Sheet

0

20

40

60

80

100

120

140

2.3 2.8 3.3 3.8 4.3 4.8 5.3
INPUT VOLTAGE (V)

QUIESCENT CURRENT (µA)

09887-039

4

1

3

T

2

CH1 2.00V

B

W

CH4 5.00V

B

W

M 40.0µs A CH3 2.2V

T 11.20%

CH2 50.0mA Ω

B

W

CH3 5.00V

B

W

SW

IOUT

VOUT

EN

09887-049

4

1

3

T

2

CH1 2.00V

CH4 5.00V

M 40.0µs A CH3 2.2V

T 11.20%

B

W

CH2 50.0mA Ω

B

W

B

W

CH3 5.00V

B

W

SW

IOUT

VOUT

EN

09887-048

3.25

3.27

3.29

3.31

3.33

3.35

0 0.2 0.4 0.6 0.8 1.0 1.2

V

OUT

(V)

I

OUT

(A)

VIN = 3.6V, +85°C

VIN = 3.6V, +25°C

V

IN

= 3.6V, –40° C

09887-025

1.764

1.784

1.804

1.824

1.844

1.864

0 0.2 0.4 0.6 0.8 1.0 1.2

V

OUT

(V)

I

OUT

(A)

VIN = 3.6V, +85°C

V

IN

= 3.6V, +25°C

V

IN

= 3.6V, –40° C

09887-024

0.789

0.790

0.791

0.792

0.793

0.794

0.795

0.796

0.797

0.798

0.799

0 0.2 0.4 0.6 0.8 1.0 1.2

V

OUT

(V)

I

OUT

(A)

V

IN

= 3.6V, +85°C

VIN = 3.6V, +25°C

V

IN

= 3.6V, –40° C

09887-026

TYPICAL PERFORMANCE CHARACTERISTICS

V

= V

= V

= V

IN1

IN2

IN3

= 3.6 V, TA = 25°C, unless otherwise noted.

IN4

Figure 3. System Quiescent Current vs. Input Voltage, V

V

= 1.8 V, V

OUT2

Figure 4. BUCK1 Startup, V

= 1.2 V, V

OUT3

= 3.3 V, All Channels Unloaded

OUT4

OUT1

= 1.8 V, I

OUT1

= 5 mA

OUT1

= 3.3 V,

Figure 6. BUCK1 Load Regulation Across Temperature, V

Auto Mode

Figure 7. BUCK2 Load Regulation Across Temperature, V

Auto Mode

OUT1

OUT2

= 3.3 V,

= 1.8 V,

Figure 5. BUCK2 Startup, V

OUT2

= 3.3 V, I

= 10 mA

OUT2

Figure 8. BUCK1 Load Regulation Across Input Voltage, V

OUT1

= 3.3 V,

PWM Mode

Rev. A | Page 8 of 28

Data Sheet ADP5037

0

10

20

30

40

50

60

70

80

90

100

0.0001 0.001 0.01 0.1 1

EFFICIENCY (%)

I

OUT

(A)

V

IN

= 3.9V

V

IN

= 5.5V

V

IN

= 4.2V

09887-027

0

10

20

30

40

50

60

70

80

90

100

0.001

0.01

0.1

1

EFFICIENCY (%)

I

OUT

(A)

VIN = 4.2V

VIN = 5.5V

VIN = 3.9V

09887-018

0

10

20

30

40

50

60

70

80

90

100

0.001 0.01 0.1 1

EFFICIENCY (%)

I

OUT

(A)

VIN = 2.3V

VIN = 5.5V

VIN = 4.2V

VIN = 3.6V

09887-020

0

10

20

30

40

50

60

70

80

90

100

0.001 0.01 0.1 1

EFFICIENCY (%)

I

OUT

(A)

V

IN

= 2.3V

V

IN

= 3.6V

V

IN

= 4.2V

V

IN

= 5.5V

09887-016

0

10

20

30

40

50

60

70

80

90

100

0.001 0.01 0.1 1

EFFICIENCY(%)

I

OUT

(A)

VIN = 2.3V

V

IN

= 5.5V

VIN = 4.2V

V

IN

= 3.6V

09887-015

0

10

20

30

40

50

60

70

80

90

100

0.001 0.01 0.1 1

EFFICIENCY (%)

I

OUT

(A)

VIN = 2.3V

VIN = 4.2V

VIN = 5.5V

VIN = 3.6V

09887-017

Figure 9. BUCK1 Efficiency vs. Load Current, Across Input Voltage,

V

= 3.3 V, Auto Mode

OUT1

Figure 10. BUCK1 Efficiency vs. Load Current, Across Input Voltage,

V

= 3.3 V, PWM Mode

OUT1

Figure 12. BUCK2 Efficiency vs. Load Current, Across Input Voltage,

V

= 1.8 V, PWM Mode

OUT2

Figure 13. BUCK1 Efficiency vs. Load Current, Across Input Voltage,

V

= 0.8 V, Auto Mode

OUT1

V

= 1.8 V, Auto Mode

OUT2

Figure 11. BUCK2 Efficiency vs. Load Current, Across Input Voltage,

Figure 14. BUCK1 Efficiency vs. Load Current, Across Input Voltage,

V

= 0.8 V, PWM Mode

OUT1

Rev. A | Page 9 of 28

ADP5037 Data Sheet

0

10

20

30

40

50

60

70

80

90

100

0.001 0.01 0.1 1

EFFICIENCY (%)

I

OUT

(A)

–40°C

+25°C

+85°C

09887-028

0

10

20

30

40

50

60

70

80

90

100

0.001 0.01 0.1 1

EFFICIENCY (%)

I

OUT

(A)

+85°C

+25°C

–40°C

09887-030

0

10

20

30

40

50

60

70

80

90

100

0.001 0.01 0.1 1

EFFICIENCY (%)

I

OUT

(A)

+85°C

+25°C

–40°C

09887-029

2.5

2.6

2.7

2.8

2.9

3.0

3.1

3.2

3.3

0 0.2 0.4 0.6 0.8 1.0 1.2

FREQUENCY (MHz)

I

OUT

(A)

+85°C

+25°C

–40°C

09887-031

2

4

T

1

CH1 50.0mV M 4.00µs A CH2 240mA

T 28.40%

CH2 500mA Ω

CH4 2.00V

I

SW

VOUT

SW

09887-051

2

4

T

1

CH1 50.0mV

B

W

M 4.00µs A CH2 220mA

T 28.40%

CH2 500mA Ω

CH4 2.00V

B

W

I

SW

VOUT

SW

09887-050

Figure 15. BUCK1 Efficiency vs. Load Current, Across Temperature,

V

= 3.9 V, V

IN

= 3.3 V, Auto Mode

OUT1

Figure 16. BUCK2 Efficiency vs. Load Current, Across Temperature,

V

= 1.8 V, Auto Mode

OUT2

Figure 18. BUCK2 Switching Frequency vs. Output Current, Across

Temperature, V

Figure 19. Typical Waveforms, V

= 1.8 V, PWM Mode

OUT2

= 3.3 V, I

OUT1

OUT1

= 30 mA, Auto Mode

Figure 17. BUCK1 Efficiency vs. Load Current, Across Temperature

V

= 0.8 V, Auto Mode

OUT1

Figure 20. Typical Waveforms, V

OUT2

= 1.8 V, I

= 30 mA, Auto Mode

OUT2

Rev. A | Page 10 of 28

Data Sheet ADP5037

2

4

T

1

CH1 50mV

B

W

M 400ns A CH2 220mA

T 28.40%

CH2 500mA Ω

CH4 2.00V

B

W

I

SW

VOUT

SW

09887-053

2

4

T

1

CH1 50mV

B

W

M 400ns A CH2 220mA

T 28.40%

CH2 500mA Ω

CH4 2.00V

B

W

I

SW

VOUT

SW

09887-052

CH1 50.0mV

B

W

CH3 1.00V

B

W

CH4 2.00V

B

W

M 1.00ms A CH3 4.80V

1

3

T 30.40%

T

VOUT

VIN

SW

09887-040

1

4

T

3

CH1 50.0mV

B

W

CH3 1.00V

B

W

CH4 2.00V

B

W

M 1.00ms A CH3 4.80V

T 30.40%

VOUT

VIN

SW

09887-041

4

1

T

2

CH1 50.0mV

B

W

CH4 5.00V

B

W

M 20.0µs A CH2 356mA

T 60.000µs

CH2 50.0mA Ω

B

W

VOUT

I

OUT

SW

09887-044

4

1

T

2

CH1 50.0mV

B

W

CH4 5.00V

B

W

M 20.0µs A CH2 379mA

T 22.20%

CH2 50.0mA Ω

B

W

VOUT

I

OUT

SW

09887-043

Figure 21. Typical Waveforms, V

Figure 22. Typical Waveforms, V

OUT1

OUT2

= 3.3 V, I

= 1.8 V, I

= 30 mA, PWM Mode

OUT1

= 30 mA, PWM Mode

OUT2

Figure 24. BUCK2 Response to Line Transient , V

V

= 1.8 V, PWM Mode

OUT2

Figure 25. BUCK1 Response to Load Transient, I

V

= 3.3 V, Auto Mode

OUT1

= 4.5 V to 5.0 V,

IN2

from 1 mA to 50 mA,

OUT1

Figure 23. BUCK1 Response to Line Transient, Input Voltage from 4.5 V to

5.0 V, V

= 3.3 V, PWM Mode

OUT1

Rev. A | Page 11 of 28

Figure 26. BUCK2 Response to Load Transient, I

V

= 1.8 V, Auto Mode

OUT2

from 1 mA to 50 mA,

OUT2

ADP5037 Data Sheet

4

2

T

1

CH1 50.0mV

B

W

CH4 5.00V

B

W

M 20.0µs A CH2 408mA

T 20.40%

CH2 200mA Ω

B

W

VOUT

I

OUT

SW

09887-045

4

2

T

1

CH1 100mV

B

W

CH4 5.00V

B

W

M 20.0µs A CH2 88.0mA

T 19.20%

CH2 200mA Ω

B

W

VOUT

I

OUT

SW

09887-046

4

1

3

T

2

CH1 5.00V

B

W

CH4 5.00V

B

W

M 400ns A CH4 1.90V

T 50.00%

CH2 5.00V

B

W

CH3 5.00V

B

W

VOUT1

VOUT2

SW1

SW2

09887-060

2

3

T

1

CH1 2.00V M 40.0µs A CH3 2.2V

T 11.20%

CH2 50.0mA Ω

CH3 5.00V

VOUT

EN

I

IN

09887-064

2.780

2.785

2.790

2.795

2.800

2.805

2.810

2.815

2.820

0 0.05 0.10 0.15 0.20 0.25 0.30

V

OUT3

(V)

I

OUT

(A)

VIN = 3.3V

VIN = 5.0V

VIN = 5.5V

VIN = 4.5V

09887-032

0

50

100

150

200

250

300

350

400

2.3 2.8 3.3 3.8 4.3 4.8 5.3

RDS

ON

(mΩ)

INPUT VOLTAGE (V)

+25°C

+125°C

–40°C

09887-037

Figure 27. BUCK1 Response to Load Transient, I

V

= 3.3 V, Auto Mode

OUT1

Figure 28. BUCK2 Response to Load Transient, I

V

= 1.8 V, Auto Mode

OUT2

from 20 mA to 180 mA,

OUT1

from 20 mA to 180 mA,

OUT2

Figure 30. LDO Startup, V

OUT3

= 3.0 V, I

OUT3

= 5 mA

Figure 31. LDO Load Regulation Across Input Voltage, V

OUT3

= 2.8 V

Figure 29. VOUT and SW Waveforms for BUCK1 and BUCK2 in PWM Mode

Showing Out-of-Phase Operation

Figure 32. NMOS RDSON vs. Input Voltage Across Temperature

Rev. A | Page 12 of 28

Data Sheet ADP5037

2.3 2.8 3.3 3.8 4.3 4.8 5.3

RDS

ON

(mΩ)

INPUT VOLTAGE (V)

+125°C

+25°C

–40°C

0

50

100

150

200

250

09887-038

3.15

3.20

3.25

3.30

3.35

3.40

3.45

0 0.05 0.10 0.15 0.20 0.25 0.30

V

OUT

(V)

I

OUT

(A)

VIN = 4.2V, +85°C

V

IN

= 4.2V, –40°C

V

IN

= 4.2V, +25°C

09887-033

0

0.5

1.0

1.5

2.0

2.5

3.0

2.4 2.6 2.8 3.0 3.2 3.4 3.6 3.8 4.0 4.2 4.4 4.6 4.8 5.0 5.2 5.4
V

IN

(V)

I

OUT

= 300mA

I

OUT

= 150mA

I

OUT

= 100mA

I

OUT

= 1mA

I

OUT

= 10mA I

OUT

= 100µA

09887-034

V

OUT

(V)

0 0.05 0.10 0.15 0.20 0.25

GROUND CURRENT ( µ A)

LOAD CURRENT ( A)

0

5

10

15

20

25

30

35

40

45

50

09887-036

2

T

1

CH1 100mV

B

W

M 40.0µs A CH2 52.0mA

T 19.20%

CH2 100mA Ω

B

W

VOUT

I

OUT

09887-047

2

3

T

1

CH1 20.0mV

CH3 1.00V

M 100µs A CH3 4.80V

T 28.40%

VOUT

VIN

09887-042

Figure 33. PMOS RDSON vs. Input Voltage Across Temperature

Figure 34. LDO Load Regulation Across Temperature, V

IN3

= 4.2 V, V

OUT3

= 3.3 V

Figure 36. LDO Ground Current vs. Output Load, V

Figure 37. LDO Response to Load Transient, I

V

= 2.8 V

OUT3

OUT3

= 3.3 V, V

IN3

OUT3

= 2.8 V

from 1 mA to 80 mA,

Figure 35. LDO Line Regulation Across Output Load, V

OUT3

= 2.8 V

Figure 38. LDO Response to Line Transient, Input Voltage from 4.5 V to 5.5 V,

V

= 2.8 V

OUT3

Rev. A | Page 13 of 28

ADP5037 Data Sheet

60

55

50

45

40

35

30

25

0.001 0.01 0.1 1 10 100
I

LOAD

(mA)

RMS NOISE (µV)

VIN = 3.3V

VIN = 5V

09887-055

60

65

55

50

45

40

35

30

25

0.001 0.01 0.1 1 10 100
I

LOAD

(mA)

RMS NOISE (µV)

09887-056

V

IN

= 3.3V

V

IN

= 5V

0

–10

–20

–30

–40
–50

–60

–70
–80

–90

–100

10 100 1k 10k 100k 1M 10M

FREQUENCY ( Hz )

PSRR (dB)

100µA
1mA
10mA
50mA
100mA
150mA

09887-057

0

–20

–40

–60

–80

–100

–120

10 100 1k 10k 100k 1M 10M

FREQUENCY ( Hz )

PSRR (dB)

100µA
1mA
10mA
50mA
100mA
150mA

09887-058

0

–20

–40

–60

–80

–100

–120

10 100 1k 10k 100k 1M 10M

FREQUENCY ( Hz )

PSRR (dB)

100µA
1mA
10mA
50mA
100mA
150mA

09887-059

0

–10

–20

–30

–40
–50

–60

–70
–80

–90

–100

10 100 1k 10k 100k 1M 10M

FREQUENCY ( Hz )

PSRR (dB)

100µA
1mA
10mA
50mA
100mA
150mA

09887-061

Figure 39. LDO Output Noise vs. Load Current, Across Input Voltage,

V

= 2.8 V

OUT3

Figure 40. LDO Output Noise vs. Load Current, Across Input Voltage,

V

= 3.0 V

OUT3

Figure 42. LDO PSRR Across Output Load, V

Figure 43. LDO PSRR Across Output Load, V

= 3.3 V, V

IN3

= 5.0 V, V

IN3

OUT3

OUT3

= 3.0 V

= 2.8 V

Figure 41. LDO PSRR Across Output Load, V

= 3.3 V, V

IN3

OUT3

= 2.8 V

Figure 44. LDO PSRR Across Output Load, V

= 5.0 V, V

IN3

OUT3

= 3.0 V

Rev. A | Page 14 of 28

Data Sheet ADP5037

IN

P

η

12

+1

)(1

r

II

OUT1

RMSOUT

×=

POWER DISSIPATION AND THERMAL CONSIDERATIONS

The ADP5037 is a highly efficient µPMU, and, in most cases,
the power dissipated in the device is not a concern. However,
if the device operates at high ambient temperatures and maxi­mum loading condition, the junction temperature can reach
the maximum allowable operating limit (125°C).

When the temperature exceeds 150°C, the ADP5037 turns off
all the regulators, allowing the device to cool down. When the
die temperature falls below 130°C, the ADP5037 resumes
normal operation.

This section provides guidelines to calculate the power dissi­pated in the device and ensure that the ADP5037 operates
below the maximum allowable junction temperature.

The efficiency for each regulator on the ADP5037 is given by

OUT

P

(1)

100%×=

BUCK REGULATOR POWER DISSIPATION

The power loss of the buck regulator is approximated by

= P

P

LOSS

where:

P

is the power dissipation on one of the ADP5037 buck

DBUCK

regulators.

P

is the inductor power losses.

L

The inductor losses are external to the device, and they do not
have any effect on the die temperature.

The inductor losses are estimated (without core losses) by

P

≈ I

L

where:

DCR

is the inductor series resistance.

L

I

is the rms load current of the buck regulator.

OUT1(RMS)

+ PL (3)

DBUCK

2

OUT1(RMS)

× DCRL (4)

where:

η is the efficiency.
P

is the input power.

IN

P

is the output power.

OUT

Power loss is given by

P

= PIN − P

LOSS

(2a)

OUT

or

P

= P

LOSS

(1− η)/η (2b)

OUT

Power dissipation can be calculated in several ways. The most
intuitive and practical is to measure the power dissipated at the
input and all the outputs. Perform the measurements at the
worst-case conditions (voltages, currents, and temperature).
The difference between input and output power is dissipated in
the device and the inductor. Use Equation 4 to derive the power
lost in the inductor and, from this, use Equation 3 to calculate
the power dissipation in the ADP5037 buck converter.

A second method to estimate the power dissipation uses the
efficiency curves provided for the buck regulator, and the power
lost on each LDO can be calculated using Equation 12. When
the buck efficiency is known, use Equation 2b to derive the total
power lost in the buck regulator and inductor, use Equation 4 to
derive the power lost in the inductor, and then calculate the
power dissipation in the buck converter using Equation 3. Add
the power dissipated in the buck and in the two LDOs to find
the total dissipated power.

Note that the buck efficiency curves are typical values and may
not be provided for all possible combinations of V
I

To account for these variations, it is necessary to include a

OU T.

, V

, and

IN

OUT

safety margin when calculating the power dissipated in the buck.

A third way to estimate the power dissipation is analytical and
involves modeling the losses in the buck circuit provided by
Equation 8 to Equation 11 and the losses in the LDO provided
by Equation 12.

(5)

where r is the normalized inductor ripple current.

r = V

× (1 − D)/(I

OUT1

× L × fSW) (6)

OUT1

where:

L is the inductance.
f

is the switching frequency.

SW

D is the duty cycle.

D = V

OUT1/VIN1

The ADP5037 buck regulator power dissipation, P

(7)

,

DBUCK

includes the power switch conductive losses, the switch losses, and
the transition losses of each channel. There are other sources of
loss, but these are generally less significant at high output load
currents, where the thermal limit of the application is. Equation
8 captures the calculation that must be made to estimate the
power dissipation in the buck regulator.

P

DBUCK

= P

COND

+ PSW + P

(8)

TRAN

The power switch conductive losses are due to the output current,
I

, flowing through the P-MOSFET and the N-MOSFET

OUT1

power switches that have internal resistance, RDS
RDS

where RDS

. The amount of conductive power loss is found by

ON-N

P

COND

= [RDS

ON-P

× D + RDS

ON-P

× (1 − D)] × I

ON-N

is approximately 0.2 Ω, and RDS

ON-P

OUT1

is approxi-

ON-N

and

2

(9)

mately 0.16 Ω at 125°C junction temperature and VIN1 = VIN2 =

3.6 V. At VIN1 = VIN2 = 2.3 V, these values change to 0.31 Ω and

0.21 Ω, respectively, and at VIN1 = VIN2 = 5.5 V, the values are

0.16 Ω and 0.14 Ω, respectively.

Rev. A | Page 15 of 28

ADP5037 Data Sheet

Switching losses are associated with the current drawn by the
driver to turn on and turn off the power devices at the switching
frequency. The amount of switching power loss is given by

P

SW

= (C

GATE-P

+ C

GATE-N

) × V

IN1

2

× f

SW

(10)

where:

C

is the P-MOSFET gate capacitance.

GAT E-P

C

is the N-MOSFET gate capacitance.

GAT E-N

For the ADP5037, the total of (C

GAT E-P

+ C

GAT E-N

) is

approximately 150 pF.

The transition losses occur because the P-channel power
MOSFET cannot be turned on or off instantaneously, and the
SW node takes some time to slew from near ground to near
V

(and from V

OUT1

to ground). The amount of transition

OUT1

loss is calculated by

P

= V

× I

× (t

+ t

where t

TRAN

RISE

and t

IN1

OUT1

are the rise time and the fall time of the

FAL L

RISE

FALL

) × f

SW

(11)

switching node, SW. For the ADP5037, the rise and fall times of
SW are in the order of 5 ns.

If the preceding equations and parameters are used for estimat­ing the converter efficiency, it must be noted that the equations
do not describe all of the converter losses, and the parameter
values given are typical numbers. The converter performance
also depends on the choice of passive components and board
layout; therefore, a sufficient safety margin should be included
in the estimate.

LDO Regulator Power Dissipation

The power loss of a LDO regulator is given by

P

DLDO

= [(VIN − V

OUT

) × I

] + (VIN × I

LOAD

) (12)

GND

where:

I

is the load current of the LDO regulator.

LOAD

V

and V

IN

are input and output voltages of the LDO,

OUT

respectively.

I

is the ground current of the LDO regulator.

GND

Power dissipation due to the ground current is small and it
can be ignored.

The total power dissipation in the ADP5037 simplifies to

P

D

= P

DBUCK1

+ P

DBUCK2

+ P

DLDO1

+ P

(13)

DLDO2

JUNCTION TEMPERATURE

In cases where the board temperature, TA, is known, the
thermal resistance parameter, θ
junction temperature rise. T
the formula

T

= TA + (PD × θJA) (14)

J

The typical θ

value for the 24-lead, 4 mm × 4 mm LFCSP is

JA

35°C/W (see Tab l e 6). A very important factor to consider is
that θ

is based on a 4-layer 4 in × 3 in, 2.5 oz copper, as per

JA

JEDEC standard, and real applications may use different sizes
and layers. It is important to maximize the copper used to remove
the heat from the device. Copper exposed to air dissipates heat
better than copper used in the inner layers. The exposed pad
should be connected to the ground plane with several vias.

If the case temperature can be measured, the junction
temperature is calculated by

T

= TC + (PD × θJC) (15)

J

where T

is the case temperature and θJC is the junction-to-case

C

thermal resistance provided in Table 6.

When designing an application for a particular ambient
temperature range, calculate the expected ADP5037 power
dissipation (P

) due to the losses of all channels by using the

D

Equation 8 to Equation 13. From this power calculation, the
junction temperature, T

, can be estimated using Equation 14.

J

The reliable operation of the converter and the two LDO regulators
can be achieved only if the estimated die junction temperature of
the ADP5037 (Equation 14) is less than 125°C. Reliability and
mean time between failures (MTBF) are highly affected by increas­ing the junction temperature. Additional information about
product reliability can be found from the ADI Reliability Handbook,
which can be found at www.analog.com/reliability_handbook.

, can be used to estimate the

JA

is calculated from TA and PD using

J

Rev. A | Page 16 of 28

Data Sheet ADP5037

LDO

CONTROL

LDO

UNDERVOLTAGE

LOCKOUT

SOFT START

PWM/

PSM

CONTROL

BUCK2

DRIVER

AND

ANTISHOOT

THROUGH

SOFT START

DRIVER

AND

ANTISHOOT

THROUGH

OSCILLATOR

THERMAL

SHUTDOWN

SYSTEM

UNDERVOLTAGE

LOCKOUT

PWM
COMP

GM ERROR

AMP

GM ERROR
AMP

PSM

COMP

PSM
COMP

LOW
CURRENT

I

LIMIT

PWM

COMP

LOW

CURRENT

I

LIMIT

R1

R2

ADP5037

VOUT1 VOUT2

VIN1

AVIN

SW1

PGND1

VIN3 AGND VOUT3

FB3

PGND2

SW2

VIN2

AVIN

75Ω

ENBK1

ENABLE

AND

MODE

CONTROL

EN1

ENBK1
ENBK2
ENLDO1
ENLDO2

600Ω

ENLDO2

75Ω

ENBK2

EN2
EN3
EN4

600Ω

ENLDO1

LDO

CONTROL

LDO

UNDERVOLTAGE

LOCKOUT

R3

R4

VIN4

VOUT4

AVIN

FB4

B

SEL

OP

MODE

MODE2

A

Y

MODE

FB1 FB2

PWM/

PSM

CONTROL

BUCK1

09887-005

THEORY OF OPERATION

POWER MANAGEMENT UNIT

The ADP5037 is a micropower management units (micro
PMU) combining two step-down (buck) dc-to-dc convertors
and two low dropout linear regulators (LDOs). The high
switching frequency and tiny 24-lead LFCSP package allow for a
small power management solution.

To combine these high performance regulators into the micro

Figure 45. Functional Block Diagram

PMU, there is a system controller allowing them to operate
together.

The buck regulators can operate in forced PWM mode if the
MODE pin is at a logic high level. In forced PWM mode, the
buck switching frequency is always constant and does not
change with the load current. If the MODE pin is at logic low
level, the switching regulators operate in auto PWM/PSM
mode. In this mode, the regulators operate at fixed PWM
frequency when the load current is above the PSM current
threshold. When the load current falls below the PSM current
threshold, the regulator in question enters PSM, where the
switching occurs in bursts. The burst repetition rate is a
function of the current load and the output capacitor value.
This operating mode reduces the switching and quiescent

current losses. The auto PWM/PSM mode transition is
controlled independently for each buck regulator. The two
bucks operate synchronized to each other.

The ADP5037 has individual enable pins (EN1 to EN4) control­ling the activation of each regulator. The regulators are activated
by a logic level high applied to the respective EN pin. EN1 controls
BUCK1, EN2 controls BUCK2, EN3 controls LDO1, and EN4
controls LDO2.

Regulator output voltages are set through external resistor
dividers or can be optionally factory programmed to default
values (see the Ordering Guide section).

When a regulator is turned on, the output voltage ramp rate is
controlled though a soft start circuit to avoid a large inrush
current due to the charging of the output capacitors.

Rev. A | Page 17 of 28

ADP5037 Data Sheet

AVIN

VOUT3

VOUT4

VOUT1

VUVLO

VOUT2

VPOR

BUCK2

PULL-DOWN

BUCK1,

LDO1,

LDO2

PULL-DOWNS

50µs (MIN)

30µs
(MIN)

50µs (MIN)

30µs

(MIN)

09887-006

Thermal Protection

In the event that the junction temperature rises above 150°C,
the thermal shutdown circuit turns off all the regulators. Extreme
junction temperatures can be the result of high current opera­tion, poor circuit board design, or high ambient temperature.
A 20°C hysteresis is included so that when thermal shutdown
occurs, the regulators do not return to operation until the on-chip
temperature drops below 130°C. When coming out of thermal
shutdown, all regulators restart with soft start control.

Undervoltage Lockout

To protect against battery discharge, undervoltage lockout
(UVLO) circuitry is integrated into the system. If the input
voltage on VIN1 drops below a typical 2.15 V UVLO threshold,
all channels shut down. In the buck channels, both the power
switch and the synchronous rectifier turn off. When the voltage
on VIN1 rises above the UVLO threshold, the part is enabled
once more.

Alternatively, the user can select device models with a UVLO
set at a higher level, suitable for USB applications. For these
models, the device reaches the turn-off threshold when the
input supply drops to 3.65 V typical.

In case of a thermal or UVLO event, the active pull-downs (if
factory enabled) are enabled to discharge the output capacitors
quickly. The pull-down resistors remain engaged until the thermal
fault event is no longer present, or the input supply voltage falls
below the V

voltage level. The typical value of V

POR

is approx-

POR

imately 1 V.

Enable/Shutdown

The ADP5037 has an individual control pin for each regulator.
A logic level high applied to the ENx pin activates a regulator,
whereas a logic level low turns off a regulator.

Figure 46 shows the regulator activation timings for the

ADP5037 when all enable pins are connected to AV I N. Also

shown is the active pull-down activation.

Figure 46. Regulator Sequencing on the ADP5037 (

EN1 = EN2 = EN3 = EN4 = V

AVIN

)

Rev. A | Page 18 of 28

BUCK

PGND1

FB1

SW1

R1

R2

VOUT1

VOUT1

VIN1

L1

1µH

C5
10µF

V

OUT1

= V

FB1

+ 1

R1
R2

09887-008

Data Sheet ADP5037

BUCK1 AND BUCK2

The buck uses a fixed frequency and high speed current mode
architecture. The buck operates with an input voltage of 2.3 V
to 5.5 V.

The buck output voltage is set through external resistor
dividers, shown in Figure 47 for BUCK1. The output voltage
can optionally be factory programmed to default values as
indicated in the Ordering Guide section. In this event, R1 and
R2 are not needed, and FB1 can be left unconnected. In all
cases, VOUT1 must be connected to the output capacitor. FB1
is 0.5 V.

Figure 47. BUCK1 External Output Voltage Setting

Control Scheme

The bucks operate with a fixed frequency, current mode PWM
control architecture at medium to high loads for high efficiency
but shift to a power save mode (PSM) control scheme at light
loads to lower the regulation power losses. When operating in
fixed frequency PWM mode, the duty cycle of the integrated
switches is adjusted and regulates the output voltage. When
operating in PSM at light loads, the output voltage is controlled
in a hysteretic manner, with higher output voltage ripple. During
part of this time, the converter is able to stop switching and
enters an idle mode, which improves conversion efficiency.

PWM Mode

In PWM mode, the bucks operate at a fixed frequency of 3 MHz
set by an internal oscillator. At the start of each oscillator cycle,
the pFET switch is turned on, sending a positive voltage across
the inductor. Current in the inductor increases until the current
sense signal crosses the peak inductor current threshold that
turns off the pFET switch and turns on the nFET synchronous
rectifier. This sends a negative voltage across the inductor,
causing the inductor current to decrease. The synchronous
rectifier stays on for the rest of the cycle. The buck regulates the
output voltage by adjusting the peak inductor current threshold.

Power Save Mode (PSM)

The bucks smoothly transition to PSM operation when the load
current decreases below the PSM current threshold. When
either of the bucks enters PSM, an offset is induced in the PWM
regulation level, which makes the output voltage rise. When the
output voltage reaches a level approximately 1.5% above the
PWM regulation level, PWM operation is turned off. At this
point, both power switches are off, and the buck enters an idle
mode. The output capacitor discharges until the output voltage
falls to the PWM regulation voltage, at which point the device

Rev. A | Page 19 of 28

drives the inductor to make the output voltage rise again to the
upper threshold. This process is repeated while the load current
is below the PSM current threshold.

The ADP5037 has a dedicated MODE pin controlling the PSM
and PWM operation. A high logic level applied to the MODE
pin forces both bucks to operate in PWM mode. A logic level
low sets the bucks to operate in auto PSM/PWM.

PSM Current Threshold

The PSM current threshold is set to100 mA. The bucks employ
a scheme that enables this current to remain accurately con­trolled, independent of input and output voltage levels. This
scheme also ensures that there is very little hysteresis between
the PSM current threshold for entry to and exit from the PSM.
The PSM current threshold is optimized for excellent efficiency
over all load currents.

Oscillator/Phasing of Inductor Switching

The ADP5037 ensures that both bucks operate at the same
switching frequency when both bucks are in PWM mode.

Additionally, the ADP5037 ensures that when both bucks are in
PWM mode, they operate out of phase, whereby the BUCK2
pFET starts conducting exactly half a clock period after the
BUCK1 pFET starts conducting.

Short-Circuit Protection

The bucks include frequency foldback to prevent output current
runaway on a hard short. When the voltage at the feedback pin
falls below half the target output voltage, indicating the possi­bility of a hard short at the output, the switching frequency is
reduced to half the internal oscillator frequency. The reduction
in the switching frequency allows more time for the inductor to
discharge, preventing a runaway of output current.

Soft Start

The bucks have an internal soft start function that ramps the
output voltage in a controlled manner upon startup, thereby
limiting the inrush current. This prevents possible input voltage
drops when a battery or a high impedance power source is
connected to the input of the converter.

Current Limit

Each buck has protection circuitry to limit the amount of
positive current flowing through the pFET switch and the
amount of negative current flowing through the synchronous
rectifier. The positive current limit on the power switch limits
the amount of current that can flow from the input to the
output. The negative current limit prevents the inductor
current from reversing direction and flowing out of the load.

100% Duty Operation

With a drop in input voltage, or with an increase in load
current, the buck may reach a limit where, even with the pFET
switch on 100% of the time, the output voltage drops below the
desired output voltage. At this limit, the buck transitions to a
mode where the pFET switch stays on 100% of the time. When

ADP5037 Data Sheet

LDO1

FB3

Ra

Rb

VOUT3

VOUT3

VIN3

C7
1µF

V

OUT3

= V

FB3

+ 1

Ra
Rb

09887-009

the input conditions change again and the required duty cycle
falls, the buck immediately restarts PWM regulation without
allowing overshoot on the output voltage.

Active Pull-Downs

All regulators have optional, factory programmable, active pull­down resistors discharging the respective output capacitors
when the regulators are disabled. The pull-down resistors are
connected between VOUTx and AGND. Active pull-downs are
disabled when the regulators are turned on. The typical value of
the pull-down resistor is 600 Ω for the LDOs and 75 Ω for the
bucks. Figure 46 shows the activation timings for the active
pull-downs during regulator activation and deactivation.

LDO1 AND LDO2

The ADP5037 contains two LDOs with low quiescent current
and low dropout voltage, and provides up to 300 mA of output
current. Drawing a low 10 μA quiescent current (typical) at no
load makes the LDO ideal for battery-operated portable
equipment.

Each LDO operates with an input voltage of 1.7 V to 5.5 V. The
wide operating range makes these LDOs suitable for cascading
configurations where the LDO supply voltage is provided from
one of the buck regulators.

Each LDO output voltage is set through external resistor
dividers as shown in Figure 48 for LDO1. The output voltage
can optionally be factory programmed to default values as
indicated in the Ordering Guide section. In this event, Ra and
Rb are not needed, and FB3 must be connected to the top of the
capacitor on VOUT3. FB3 is 0.5 V.

Figure 48. LDO1 External Output Voltage Setting

The LDOs also provide high power supply rejection ratio
(PSRR), low output noise, and excellent line and load transient
response with only a small 1 µF ceramic input and output
capacitor.

LDO1 is optimized to supply analog circuits because it offers
better noise performance compared to LDO2. LDO1 should be
used in applications where noise performance is critical.

Rev. A | Page 20 of 28

Data Sheet ADP5037

−×

2

)(

RIPPLE

MAXLOAD

PEAK

I

II +=

0

2

4

6

8

10

12

0 1 2 3 4 5 6

DC BIAS VOL TAGE (V)

CAPACITANCE (µ F)

09887-010

Taiyo Yuden

CBC3225T1R0MR

3.2 × 2.5 × 2.5

2000

71

APPLICATIONS INFORMATION

BUCK EXTERNAL COMPONENT SELECTION

Trade-offs between performance parameters such as efficiency
and transient response can be made by varying the choice of
external components in the applications circuit, as shown in
Figure 1.

Feedback Resistors

For the adjustable model, referring to Figure 47, the total
combined resistance for R1 and R2 is not to exceed 400 kΩ.

Inductor

The high switching frequency of the ADP5037 bucks allows for
the selection of small chip inductors. For best performance, use
inductor values between 0.7 μH and 3 μH. Suggested inductors
are shown in Tabl e 8.

The peak-to-peak inductor current ripple is calculated using
the following equation:

VVV

IN

I

RIPPLE

OUT

=

IN

SW

where:

f

is the switching frequency.

SW

L is the inductor value.

The minimum dc current rating of the inductor must be greater
than the inductor peak current. The inductor peak current is
calculated using the following equation:

)(

OUT

LfV

××

Ceramic capacitors are manufactured with a variety of dielec­trics, each with a different behavior over temperature and
applied voltage. Capacitors must have a dielectric adequate
to ensure the minimum capacitance over the necessary
temperature range and dc bias conditions. X5R or X7R
dielectrics with a voltage rating of 6.3 V or 10 V are recom­mended for best performance. Y5V and Z5U dielectrics are
not recommended for use with any dc-to-dc converter because
of their poor temperature and dc bias characteristics.

The worst-case capacitance accounting for capacitor variation
over temperature, component tolerance, and voltage is calcu­lated using the following equation:

C

= C

EFF

× (1 − TEMPCO) × (1 − TOL)

OUT

where:

C

is the effective capacitance at the operating voltage.

EFF

TEMPCO is the worst-case capacitor temperature coefficient.
TOL is the worst-case component tolerance.

In this example, the worst-case temperature coefficient
(TEMPCO) over −40°C to +85°C is assumed to be 15% for an
X5R dielectric. The tolerance of the capacitor (TOL) is assumed
to be 10%, and C

is 9.2 μF at 1.8 V, as shown in Figure 49.

OUT

Substituting these values in the equation yields

C

= 9.2 μF × (1 − 0.15) × (1 − 0.1) = 7.0 μF

EFF

To guarantee the performance of the bucks, it is imperative
that the effects of dc bias, temperature, and tolerances on the
behavior of the capacitors be evaluated for each application.

Inductor conduction losses are caused by the flow of current
through the inductor, which has an associated internal dc
resistance (DCR). Larger sized inductors have smaller DCR,
which may decrease inductor conduction losses. Inductor core
losses are related to the magnetic permeability of the core material.
Because the bucks are high switching frequency dc-to-dc
converters, shielded ferrite core material is recommended for
its low core losses and low EMI.

Output Capacitor

Higher output capacitor values reduce the output voltage ripple
and improve load transient response. When choosing this value,
it is also important to account for the loss of capacitance due to
output voltage dc bias.

Table 8. Suggested 1.0 μH Inductors

Vendor Model Dimensions (mm) I

Murata LQM2MPN1R0NG0B 2.0 × 1.6 × 0.9 1400 85
Murata LQM18FN1R0M00B 3.2 × 2.5 × 1.5 2300 54

Coilcraft XFL4020-102ME 4.0 × 4.0 × 2.1 5400 11
Coilcraft XPL2010-102ML 1.9 × 2.0 × 1.0 3750 89
Toko MDT2520-CN 2.5 × 2.0 × 1.2 1350 85

Rev. A | Page 21 of 28

Figure 49. Capacitance vs. Voltage Characteristic

(mA) DCR (mΩ)

SAT

ADP5037 Data Sheet

OUTSW

IN

OUTSW

RIPPLE

RIPPLE

CLf

V

Cf

I

V

×××

≈

××

=

2

)2(

8

π

RIPPLE

RIPPLE

COUT

I

V

ESR ≤

IN

OUT

IN

OUT

MAXLOAD

CIN

V

VVV

II

)(

)(

−

≥

VIN1

VIN3

EN1

PWM

PSM/PWM

2.3V TO

5.5V

SW1
FB1

R2

R1

VOUT1

PGND1

MODE

C5
10µF

V

OUT1

@

800mA

L1 1µH

EN1

BUCK1

MODE

C3

1µF

C2

4.7µF

C1

4.7µF

AVIN

C

AVIN

0.1µF

C4

1µF

VIN2

EN2

AGND

EN2

BUCK2

MODE

EN3

1.7V TO

5.5V

EN4

VIN4

ON

OFF

ON

OFF

ON

OFF

EN3

LDO1

(ANALOG)

ADP5037

HOUSEKEEPING

SW2
FB2

R4

R3

VOUT2

PGND2

C6
10µF

V

OUT2

@

800mA

L2 1µH

FB3

R6

R5

VOUT3

C7
1µF

V

OUT3

@

300mA

FB4

R8

R7

VOUT4

C8
1µF

V

OUT4

@

300mA

EN4

LDO2

(DIGITAL)

09887-021

The peak-to-peak output voltage ripple for the selected output
capacitor and inductor values is calculated using the following
equation:

Capacitors with lower effective series resistance (ESR) are
preferred to guarantee low output voltage ripple, as shown in
the following equation:

The effective capacitance needed for stability, which includes
temperature and dc bias effects, is a minimum of 7 µF and a
maximum of 40 µF.

The buck regulators require 10 µF output capacitors to guaran­tee stability and response to rapid load variations and to transition
into and out of the PWM/PSM modes. A list of suggested capaci­tors is shown in Tab l e 9. In certain applications where one or
both buck regulator powers a processor, the operating state is
known because it is controlled by software. In this condition,
the processor can drive the MODE pin according to the operating
state; consequently, it is possible to reduce the output capacitor
from 10 µF to 4.7 µF because the regulator does not expect a
large load variation when working in PSM mode (see Figure 50).

Input Capacitor

Higher value input capacitors help to reduce the input voltage
ripple and improve transient response. Maximum input
capacitor current is calculated using the following equation:

To minimize supply noise, place the input capacitor as close as
possible to the VINx pin of the buck. As with the output
capacitor, a low ESR capacitor is recommended.

The effective capacitance needed for stability, which includes
temperature and dc bias effects, is a minimum of 3 µF and a
maximum of 10 µF. A list of suggested capacitors is shown in
Table 9 and Ta b l e 10.

Table 9. Suggested 10 μF Capacitors

Voltage

Case

Vendor Type Model

Size

Rating
(V)

Murata X5R GRM188R60J106 0603 6.3
TDK X5R C1608JB0J106K 0603 6.3
Panasonic X5R ECJ1VB0J106M 0603 6.3

Table 10. Suggested 4.7 μF Capacitors

Voltage

Case

Vendor Type Model

Size

Rating
(V)

Murata X5R GRM188R60J475ME19D 0402 6.3
Taiyo Yuden X5R JMK107BJ475 0402 6.3
Panasonic X5R ECJ-0EB0J475M 0402 6.3

Table 11. Suggested 1.0 μF Capacitors

Vendor Type Model

Size

Murata X5R GRM155B30J105K 0402 6.3
TDK X5R C1005JB0J105KT 0402 6.3
Panasonic X5R ECJ0EB0J105K 0402 6.3

Case

Taiyo

X5R LMK105BJ105MV-F 0402 10.0

Yuden

Voltage
Rating (V)

Figure 50. Processor System Power Management with PSM/PWM Control

Rev. A | Page 22 of 28

Data Sheet ADP5037

1.2

1.0

0.8

0.6

0.4

0.2

0

0 1 2 3 4 5 6

DC BIAS VOL TAGE (V)

CAPACITANCE (µ F)

09887-012

LDO EXTERNAL COMPONENT SELECTION

Feedback Resistors

For the adjustable model, the maximum value of Rb is not to
exceed 200 kΩ (see Figure 48).

Output Capacitor

The ADP5037 LDOs are designed for operation with small, space­saving ceramic capacitors, but function with most commonly
used capacitors as long as care is taken with the ESR value. The
ESR of the output capacitor affects stability of the LDO control
loop. A minimum of 0.70 µF capacitance with an ESR of 1 Ω
or less is recommended to ensure that stability of the ADP5037.
Transient response to changes in load current is also affected by
output capacitance. Using a larger value of output capacitance
improves the transient response of the ADP5037 to large
changes in load current.

Input Bypass Capacitor

Connecting a 1 µF capacitor from VIN3 and VIN4 to ground
reduces the circuit sensitivity to printed circuit board (PCB)
layout, especially when long input traces or high source imped­ance is encountered. If greater than 1 µF of output capacitance
is required, increase the input capacitor to match it.

Input and Output Capacitor Properties

Use any good quality ceramic capacitors with the ADP5037 as
long as they meet the minimum capacitance and maximum ESR
requirements. Ceramic capacitors are manufactured with a variety
of dielectrics, each with a different behavior over temperature
and applied voltage. Capacitors must have a dielectric adequate
to ensure the minimum capacitance over the necessary tempera­ture range and dc bias conditions. X5R or X7R dielectrics with a
voltage rating of 6.3 V or 10 V are recommended for best perfor­mance. Y5V and Z5U dielectrics are not recommended for use
with any LDO because of their poor temperature and dc bias
characteristics.

Figure 51 depicts the capacitance vs. voltage bias characteristic
of a 0402 1 µF, 10 V, X5R capacitor. The voltage stability of a
capacitor is strongly influenced by the capacitor size and voltage
rating. In general, a capacitor in a larger package or with higher
voltage rating exhibits better stability. The temperature variation
of the X5R dielectric is about ±15% over the −40°C to +85°C

temperature range and is not a function of package or voltage
rating.

Figure 51. Capacitance vs. Voltage Characteristic

Use the following equation to determine the worst-case capa­citance accounting for capacitor variation over temperature,
component tolerance, and voltage:

C

= C

EFF

× (1 − TEMPCO) × (1 − TOL)

BIAS

where:
C

is the effective capacitance at the operating voltage.

BIAS

TEMPCO is the worst-case capacitor temperature coefficient.
TOL is the worst-case component tolerance.

In this example, the worst-case temperature coefficient
(TEMPCO) over −40°C to +85°C is assumed to be 15% for an
X5R dielectric. The tolerance of the capacitor (TOL) is assumed
to be 10%, and C

is 0.85 μF at 1.8 V as shown in Figure 51.

BIAS

Substituting these values into the following equation,

C

= 0.85 μF × (1 − 0.15) × (1 − 0.1) ≈ 0.65 μF

EFF

Therefore, the capacitor chosen in this example meets the
minimum capacitance requirement of the LDO over
temperature and tolerance at the chosen output voltage.

To guarantee the performance of the ADP5037, it is imperative
that the effects of dc bias, temperature, and tolerances on the
behavior of the capacitors be evaluated for each application.

Rev. A | Page 23 of 28

ADP5037 Data Sheet

PCB LAYOUT GUIDELINES

Poor layout can affect ADP5037 performance, causing electro­magnetic interference (EMI) and electromagnetic compatibility
(EMC) problems, ground bounce, and voltage losses. Poor
layout can also affect regulation and stability. A good layout is
implemented using the following guidelines.

• Place the inductor, input capacitor, and output capacitor

close to the IC using short tracks. These components carry
high switching frequencies, and large tracks act as antennas.

• Route the output voltage path away from the inductor and

SW node to minimize noise and magnetic interference.

• Maximize the size of ground metal on the component side

to help with thermal dissipation.

• Use a ground plane with several vias connecting to the

component side ground to further reduce noise
interference on sensitive circuit nodes.

• Connect VIN1, VIN2, and AVIN together close to the IC

using short tracks.

Rev. A | Page 24 of 28

Data Sheet ADP5037

VIN1

VIN3

EN1

PWM

PSM/PWM

2.3V TO

5.5V

SW1
FB1

VOUT1

PGND1

MODE

C5
10µF

V

OUT1

@

800mA

L1 1µH

EN1

BUCK1

MODE

C3

1µF

C2

4.7µF

C1

4.7µF

AVIN

C

AVIN

0.1µF

C4

1µF

VIN2

EN2

AGND

EN2

BUCK2

MODE

EN3

1.7V TO

5.5V

EN4

VIN4

ON

OFF

ON

OFF

ON

OFF

EN3

LDO1

(ANALOG)

ADP5037

HOUSEKEEPING

SW2
FB2

R3

VOUT2

PGND2

C6
10µF

V

OUT2

@

800mA

L2 1µH

FB3

VOUT3

C7
1µF

V

OUT3

@

300mA

FB4

VOUT4

C8
1µF

V

OUT4

@

300mA

EN4

LDO2

(DIGITAL)

09887-022

VIN1

VIN3

EN1

PWM

PSM/PWM

2.3V TO

5.5V

SW1
FB1

R2

R1

VOUT1

PGND1

MODE

C5
10µF

V

OUT1

@

800mA

L1 1µH

EN1

BUCK1

MODE

C3

1µF

C2

4.7µF

C1

4.7µF

AVIN

C

AVIN

0.1µF

C4

1µF

VIN2

EN2

AGND

EN2

BUCK2

MODE

EN3

1.7V TO

5.5V

EN4

VIN4

ON

OFF

ON

OFF

ON

OFF

EN3

LDO1

(ANALOG)

ADP5037

HOUSEKEEPING

SW2
FB2

R4

R3

VOUT2

PGND2

C6
10µF

V

OUT2

@

800mA

L2 1µH

FB3

R6

R5

VOUT3

C7
1µF

V

OUT3

@

300mA

FB4

R8

R7

VOUT4

C8
1µF

V

OUT4

@

300mA

EN4

LDO2

(DIGITAL)

09887-023

TYPICAL APPLICATION SCHEMATICS

Figure 52. ADP5037 Fixed Output Voltages with Enable Pins

Figure 53. ADP5037 Adjustable Output Voltages with Enable Pins

Rev. A | Page 25 of 28

ADP5037 Data Sheet

1 µH, 0.086 Ω, 1350 mA

MDT2520-CN

Toko

2.5 × 2.0 × 1.2

BILL OF MATERIALS

Table 12.

Reference Value Part Number Vendor Package or Dimension (mm)

C

0.1 µF, X5R, 6.3 V JMK105BJ104MV-F Taiyo -Yuden 0402

AVIN

C3, C4, C7, C8 1 µF, X5R, 6.3 V LMK105BJ105MV-F Ta i yo-Yuden 0402
C1, C2 4.7 µF, X5R, 6.3 V ECJ-0EB0J475M Panasonic-ECG 0402
C5, C6 10 µF, X5R, 6.3 V JMK107BJ106MA-T Ta i yo-Yuden 0603
L1, L2 1 µH, 0.18 Ω, 850 mA BRC1608T1R0M Tai yo-Yuden 0603
1 µH, 0.085 Ω, 1400 mA LQM2MPN1R0NG0B Murata 2.0 × 1.6 × 0.9
1 µH, 0.059 Ω, 900 mA EPL2014-102ML Coilcraft 2.0 × 2.0 × 1.4

IC1 Four-regulator micro PMU ADP5037 Analog Devices 24-lead LFCSP

Rev. A | Page 26 of 28

Data Sheet ADP5037

0.50

BSC

0.50

0.40

0.30

0.30

0.25

0.20

COMPLIANT

TO

JEDEC STANDARDS MO-220-WGGD-8.

072809A

BOTTOMVIEWTOPVIEW

EXPOSED

PAD

PIN 1
INDICATOR

4.10

4.00 SQ

3.90

SEATING

PLANE

0.80

0.75

0.70

0.05 MAX

0.02 NOM

0.20 REF

0.25 MIN

COPLANARITY

0.08

PIN 1

INDICATOR

1

24

7

12

13

18

19

6

FOR PROPER CONNECTION OF
THE EXPOSED PAD, REFER TO
THE PIN CONFIGURATION AND
FUNCTION DESCRIPTIONS
SECTION OF THIS DATA SHEET.

2.20

2.10 SQ

2.00

+125°C

Buck Channels

Package [LFCSP_WQ]

OUTLINE DIMENSIONS

Figure 54. 24-Lead Lead Frame Chip Scale Package [LFCSP_WQ]

4 mm × 4 mm Body, Very Very Thin Quad

(CP-24-10)

Dimensions shown in millimeters

ORDERING GUIDE

Temperature

Model1

Range

ADP5037ACPZ-R7 −40°C to

ADP5037ACPZ-1-R7 −40°C to

+125°C

ADP5037CP-EVALZ Evaluation Board for ADP5037ACPZ-R7

1

Z = RoHS Compliant Part.

2

For additional options, contact a local sales or distribution representative. Additional options available are:

BUCK1 and BUCK2: 3.3 V, 3.0 V, 2.8 V, 2.5 V, 2.3 V, 2.0 V, 1.8 V, 1.6 V, 1.5 V, 1.4 V, 1.3 V, 1.2 V, 1.1 V, 1.0 V, 0.9 V or adjustable.
LDO1 and LDO2: 3.3 V, 3.0 V, 2.8 V, 2.5 V, 2.25 V, 2 V, 1.8 V, 1.7 V, 1.6 V, 1.5 V, 1.2 V, 1.1 V, 1.0 V, 0.9 V, 0.8 V or adjustable.

3

UVLO: Low or High.

4

BUCK1, BUCK2, and both LDO1 and LDO2: active pull-down resistor is programmable to be either enabled or disabled.

Output
Voltage2 UVLO3

Active
Pull-Down4 Package Description

Adjustable Low Enabled on

VOUT1 = 1.2 V
VOUT2 = 3.3 V

Low Enabled on

Buck Channels
VOUT3 = 2.8 V
VOUT4 = 1.8 V

24-Lead Lead Frame Chip Scale

24-Lead Lead Frame Chip Scale
Package [LFCSP_WQ]

Package
Option

CP-24-10

CP-24-10

Rev. A | Page 27 of 28

ADP5037 Data Sheet

NOTES

©2011-2012 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
D09887-0-1/12(A)

Rev. A | Page 28 of 28