Datasheet ADP3605ARU-3, ADP3605AR-3, ADP3605AR Datasheet (Analog Devices)

120 mA Switched Capacitor

SD

OSC

CLOCK

GEN

FEEDBACK

CONTROL

LOOP

SD

SD

B

SD

SDN

C

P

+

C

P

–

PN

N

S1

S3

V

IN

V

OUT

V

SENSE

GND

S2

S4

ADP3605

a

Voltage Inverter with Regulated Output

FEATURES
Fully Regulated Output Voltage (–3 V and Adjustable)
High Output Current: 120 mA
Output Accuracy: ⴞ3%
250 kHz Switching Frequency
Low Shutdown Current: 2 ␮A Typical
Input Voltage Range from 3 V to 6 V
SO-8 and RU-14 Packages
–40ⴗC to +85ⴗC Ambient Temperature Range

APPLICATIONS
Voltage Inverters
Voltage Regulators
Computer Peripherals and Add-On Cards
Portable Instruments
Battery Powered Devices
Pagers and Radio Control Receivers
Disk Drives
Mobile Phones

ADP3605

FUNCTIONAL BLOCK DIAGRAM

GENERAL DESCRIPTION

+

SENSE

*C

4.7mF

–3.0VV

O

The ADP3605 is a 120 mA regulated output switched capacitor
voltage inverter. It provides a regulated output voltage with
minimum voltage loss and requires a minimum number of ex­ternal components. In addition, the ADP3605 does not require
the use of an inductor.

Pin-for-pin and functionally compatible with the ADP3604, the
internal oscillator of the ADP3605 runs at 500 kHz nominal
frequency which produces an output switching frequency of
250 kHz. This allows for the use of smaller charge pump and
filter capacitors.

The ADP3605 provides an accuracy of ±3% with a typical shut­down current of 2 µA. It can also operate from a single positive

V

V

+

IN

OUT

CP+

ADP3605-3

–

C

P

GND

IN

+

*C

IN

4.7mF

OFF

*FOR BEST PERFORMANCE, 10mF IS RECOMMENDED
C

P

C

IN

*C

P

4.7mF

SD

ON

0

: SPRAGUE, 293D475X0010B2W
, CO: TOKIN, 1E475ZY5UC205F

Figure 1. Typical Application Circuit

V

input voltage as low as 3 V. The ADP3605 is offered with the
regulation fixed at –3 V or adjustable via external resistors over
a –3 V to –6 V range.

REV. A

Information furnished by Analog Devices is believed to be accurate and
reliable. However, no responsibility is assumed by Analog Devices for its
use, nor for any infringements of patents or other rights of third parties
which may result from its use. No license is granted by implication or
otherwise under any patent or patent rights of Analog Devices.

One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: [phone] World Wide Web Site: http://www.analog.com
Fax: [phone] © Analog Devices, Inc., 1999

1, 2, 3

ADP3605–SPECIFICATIONS

Parameter Symbol Conditions Min Typ Max Units

OPERATING SUPPLY RANGE V

SUPPLY CURRENT I

Shutdown Mode V

OUTPUT VOLTAGE

4

LOAD REGULATION ∆V

OUTPUT RESISTANCE

Open Loop R

OUTPUT RIPPLE VOLTAGE V

SWITCHING FREQUENCY F

SHUTDOWN

Logic Input High V
Input Current I
Logic Input Low V
Input Current I

NOTES

1

Capacitors C

2

See Figure 1 Conditions.

3

All limits at temperature extremes are guaranteed via correlation using standard Statistical Quality Control (SQC) methods.

4

For the adjustable device, a 1% resistor should be used to maintain output voltage tolerance. For both device types, tolerances can be improved by >1% using larger
value and lower ESR capacitors for CO and CP.

Specifications subject to change without notice.

IN, CO

and C

in the test circuit are 4.7 µF with 0.1 Ω ESR.

P

S

S

V

O

O

RIPPLE

S

IH

IH

IL

IL

O/IO

(VIN = 5.0 V @ TA = +25ⴗC, CP = CO = 4.7 ␮F unless otherwise noted)

356V

–40°C < TA < +85°C36mA

SD

= V

IN

215µA

–40°C < TA < +85°C

IO = 60 mA –3.09 –3.0 –2.91 V

= 10 mA–120 mA, –3.15 –3 –2.85 V

I

O

–40°C ≤ T

≤ +85°C

A

4.75 V ≤ VS ≤ 6.0 V

IO = 10 mA–60 mA 0.3 mV/mA
IO = 10 mA–120 mA 0.25 mV/mA

9 Ω

C

= C

= 4.7 µF,

IN

I
I

O

= 60 mA 38 mV

LOAD

= 120 mA 75 mV

LOAD

VIN = 5 V 212 250 288 kHz

–40°C < TA < +85°C

2.4 V

1 µA

0.4 V

1 µA

ABSOLUTE MAXIMUM RATINGS

(T

= +25°C unless otherwise noted)

A

Input Voltage (V+ to GND, GND to OUT) . . . . . . . . +7.5 V

Input Voltage (V+ to OUT) . . . . . . . . . . . . . . . . . . . . . +11 V

Output Short Circuit Protection . . . . . . . . . . . . . . . . . . . 1 sec

Power Dissipation, SO-8 . . . . . . . . . . . . . . . . . . . . . . 660 mW

2

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 150°C/W

θ

JA

Power Dissipation, RU-14 . . . . . . . . . . . . . . . . . . . . . 600 mW

2

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 165°C/W

θ

JA

1

Storage Temperature Range . . . . . . . . . . . . –65°C to +150°C

Lead Temperature Range (Soldering 10 sec) . . . . . . . .+300°C

Vapor Phase (60 sec) . . . . . . . . . . . . . . . . . . . . . . . .+215°C

Infrared (15 sec) . . . . . . . . . . . . . . . . . . . . . . . . . . .+220°C

NOTES

1

This is a stress rating only; operation beyond these limits can cause the device to

be permanently damaged.

2

θ

is specified for worst case conditions with device soldered on a circuit board.

JA

Operating Temperature Range . . . . . . . . . . . –40°C to +85°C

ORDERING GUIDE

Model Output Voltage Package Description Package Options*

ADP3605AR-3 –3 V Small Outline SO-8
ADP3605AR ADJ Small Outline SO-8
ADP3605ARU-3 –3 V Thin Shrink Small Outline Package (TSSOP) RU-14

*Contact the factory for the availability of other output voltage options.

–2–

REV. A

ADP3605

WARNING!

ESD SENSITIVE DEVICE

ADP3605

NC
NC
NC
V

IN

V

OUT

NC
V

SENSE

NC
NC
NC

SD

CP–

GND

C

P

+

NC = NO CONNECT

Table I. Other Members of ADP36xx Family

1

Output Package

Model Current Option2Comments

ADP3603AR 50 mA SO-8 Nom.–3 ± 3% Inverter
ADP3604AR 120 mA SO-8 Nom.–3 ± 3% Inverter

ADP3610ARU 320 mA TSSOP-16 Nom. 3.3 VIN Doubler

NOTES

1

See individual data sheets for detailed ordering information.

2

SO = Small Outline; TSSOP = Thin Shrink Small Outline Package.

Table II. Alternative Capacitor Technologies

High

Type Life Freq Temp Size Cost

Aluminum
Electrolytic
Capacitor Fair Fair Fair Small Low

Multilayer
Ceramic
Capacitor Long Good Poor Fair1High

Solid
Tantalum Above
Capacitor Avg Avg Avg Avg Avg

OS-CON Above
Capacitor Avg Good Good Good Avg

NOTE

1

Refer to capacitor manufacturer's data sheet for operation below 0°C.

Table III. Recommended Capacitor Manufacturers

Manufacturer Capacitor Capacitor Type

Sprague 672D, 673D,

674D, 678D Aluminum Electrolytic

Sprague 675D, 173D,

199D Tantalum
Nichicon PF and PL Aluminum Electrolytic
Mallory TDC and TDL Tantalum
TOKIN MLCC Multilayer Ceramic
MuRata GRM Multilayer Ceramic

PIN FUNCTION DESCRIPTIONS

Pin Pin
SO-8 TSSOP Name Function

14 C

+ Positive Terminal for the Pump

P

Capacitor.
2 5 GND Device Ground.
36 C

– Negative Terminal for the Pump

P

Capacitor.
4 7 SD Logic Level Shutdown Pin. Apply a

logic high or connect to V

to shut-

IN

down the device. In shutdown mode,

the charge pump is turned off and

quiescent current is reduced to 2 µA

(typical). Apply a logic low or con-

nect to ground for normal operation.
58 V

SENSE

Output Voltage Sense Line. This is

used to improve load regulation by

eliminating IR drop on the high

current carrying output traces. For

normal operation, connect V

V

. See Application section for

OUT

SENSE

to

more detail.
6 1, 2, 3,

9, 12,
13, 14 NC No Connection.

710 V

OUT

Regulated Negative Output Voltage.

Connect a low ESR, 4.7 µF or larger

capacitor between this pin and de-

vice GND.
811 V

IN

Positive Supply Input Voltage. Con-

nect a low ESR bypass capacitor

between this pin and device ground

to minimize supply transients.

PIN CONFIGURATIONS

RU-14 SO-8

1

+

C

P

2

ADP3605

GND

TOP VIEW

3

C

–

P

(Not to Scale)

4

SD

NC = NO CONNECT

8

V

IN

7

V

OUT

6

NC

5

V

SENSE

CAUTION

ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily
accumulate on the human body and test equipment and can discharge without detection.
Although the ADP3605 features proprietary ESD protection circuitry, permanent damage may
occur on devices subjected to high energy electrostatic discharges larger than 600 V HBM.
Therefore, proper ESD precautions are recommended to avoid performance degradation or loss
of functionality.

–3–REV. A

ADP3605

–Typical Performance Characteristics

270

260

OSCILLATOR FREQUENCY – kHz

250

3 3.5 6

4 4.5 5 5.5

SUPPLY VOLTAGE – Volts

Figure 2. Oscillator Frequency vs.
Supply Voltage

300

280

260

240

220

OSCILLATOR FREQUENCY – kHz

4.5
VIN = +5V

4

3.5

3

2.5

IN NORMAL MODE

SUPPLY CURRENT – mA

2

1.5

–40 –15 10 35 60 85

SHUTDOWN MODE

(V

= VIN)

SD

NORMAL MODE

(V

= 0V)

SD

TEMPERATURE – 8C

Figure 3. Supply Current vs.
Temperature

140

120

100

80

60

40

INPUT CURRENT – mA

20

3

2.5

2

1.5

1

0.5

0

–2.96

–2.97

–2.98

–2.99

–3.00

–3.01

IN SHUTDOWN MODE

SUPPLY CURRENT – mA

OUTPUT VOLTAGE – Volts

–3.02

–3.03

–40 –15 85

TEMPERATURE – 8C

Figure 4. Output Voltage vs.
Temperature

–2.5

–2.6

–2.7

–2.8

–2.9

–3.0

OUTPUT VOLTAGE – Volts

–3.1

VIN = +3V

VIN = +3.5V

VIN = +4.75V

VIN = +5V

VIN = +6V

IL = 120mA

IL = 60mA

IL = 10mA

10 35 60

200

–40 –15 85

10 35 60

TEMPERATURE – 8C

Figure 5. Oscillator Frequency vs.
Temperature

3.5
NORMAL MODE

= 0V)

(V

3

2.5

2

1.5

IN NORMAL MODE

1

SUPPLY CURRENT – mA

0.5

0

34 6

SD

SHUTDOWN MODE

= VIN)

(V

SD

SUPPLY VOLTAGE – Volts

5

Figure 8. Supply Current vs. Supply
Voltage

0

10 30 130

50 70 90 110

LOAD CURRENT – mA

Figure 6. Average Input Current
vs. Output Current

7

6

5

4

3

2

IN SHUTDOWN MODE

SUPPLY CURRENT – mA

1

0

Figure 9 . Start-Up Under Full Load

–3.2

0 40 200

80 120 160

LOAD CURRENT – mA

240 280

Figure 7. Output Voltage vs. Load
Current

Figure 10. Enable/Disable Time
Under Full Load

–4–

REV. A

ADP3605

THEORY OF OPERATION

The ADP3605 uses a switched capacitor principle to generate a
negative voltage from a positive input voltage. An onboard
oscillator generates a two phase clock to control a switching
network that transfers charge between the storage capacitors.
The switches turn on and off at a 250 kHz rate, which is gener­ated from an internal 500 kHz oscillator. The basic principle
behind the voltage inversion scheme is illustrated in Figures 11
and 12.

S1

V

IN

C

S2

P

S3

+
–

S4

V

OUT

C

O

Figure 11. ADP3605 Switch Configuration Charging the
Pump Capacitor

During phase one, S1 and S2 are ON, charging the pump ca­pacitor to the input voltage. Before the next phase begins, S1
and S2

are turned OFF as well as S3 and S4 to prevent any

overlap. S3 and S4

are turned ON during the second phase (see
Figure 12) and charge stored in the pump capacitor is trans­ferred to the output capacitor.

S1 S3

V

IN

S2

+

C

P

–

S4

V

OUT

C

O

Figure 12. ADP3605 Switch Configuration Charging the
Output Capacitor

During the second phase, the positive terminal of the pump
capacitor is connected to ground through variable resistance
switch, S3, and the negative terminal is connected to the out­put, resulting in a voltage inversion at the output terminal.
The ADP3605 block diagram is shown on the front page.

APPLICATION INFORMATION
Capacitor Selection

The ADP3605’s high internal oscillator frequency permits the
use of small capacitors for both the pump and the output ca­pacitors. For a given load current, factors affecting the output
voltage performance are:

• Pump (C

• ESR of the C

) and output (CO) capacitance.

P

and CO.

P

When selecting the capacitors, keep in mind that not all manu­facturers guarantee capacitor ESR in the range required by the
circuit. In general, the capacitor’s ESR is inversely proportional
to its physical size, so larger capacitance values and higher volt­age ratings tend to reduce ESR. Since the ESR is also a function
of the operating frequency, when selecting a capacitor, make
sure its value is rated at the circuit's operating frequency.

Temperature is another factor affecting capacitor performance.
Figure 13 illustrates the temperature effect on various capaci­tors. If the circuit has to operate at temperatures significantly

different from 25°C, the capacitance and ESR values must be

carefully selected to adequately compensate for the change.
Various capacitor technologies offer improved performance over
temperature; for example, certain tantalum capacitors provide
good low-temperature ESR but at a higher cost. Table II pro­vides the ratings for different types of capacitor technologies to
help the designer select the right capacitors for the applica­tion. The exact values of C

and CO are not critical. How-

IN

ever, low ESR capacitors such as solid tantalum and multilayer
ceramic capacitors are recommended to minimize voltage loss at
high currents. Table III shows a partial list of the recommended
low ESR capacitor manufacturers.

Input Capacitor

A small 1 µF input bypass capacitor, preferably with low ESR,

such as tantalum or multilayer ceramic, is recommended to
reduce noise and supply transients and supply part of the peak
input current drawn by the ADP3605. A large capacitor is rec­ommended if the input supply is connected to the ADP3605
through long leads, or if the pulse current drawn by the device
might affect other circuitry through supply coupling.

Output Capacitor

The output capacitor (CO) is alternately charged to the CP volt­age when C
introduces steps in the V
pump charges C
ceramic or tantalum capacitors are recommended for C

is switched in parallel with CO. The ESR of C

P

, which contributes to V

O

waveform whenever the charge

OUT

ripple. Thus,

OUT

O

O

to
minimize ripple on the output. Figure 14 illustrates the output
ripple voltage effect for various capacitance and ESR values.
Note that as the capacitor value increases beyond the point
where the dominant contribution to the output ripple is due to
the ESR, no significant reduction in V

ripple is achieved by

OUT

added capacitance. Since output current is supplied solely by
the output capacitor, C

during one-half of the charge-pump

O,

cycle, peak-to-peak output ripple voltage is calculated by using
the following formula.

I

V

RIPPLE

=

××

2

L

FC

SO

I ESR

+× ×

2

LC

O

where: IL = Load Current

F

= 250 kHz nominal switching frequency

S

C

= 10 µF with an ESR of 0.15 Ω

O

mA

V

RIPPLE

=

120

kHz F

××

2 250 10

+× × =

2 120 0 15 60

mA mV

µ

.

Multiple smaller capacitors can be connected in parallel to yield
lower ESR and lower cost. For lighter loads, proportionally
smaller capacitors are required. To reduce high frequency

noise, bypass the output with a 0.1 µF ceramic capacitor in

parallel with the output capacitor.

–5–REV. A

ADP3605

Pump Capacitor

The ADP3605 alternately charges CP to the input voltage when
C

is switched in parallel with the input supply, and then trans-

P

fers charge to C

During the time C

when CP is switched in parallel with CO.

O

is charging, the peak current is approxi-

P

mately two times the output current.

During the time C

is delivering charge to CO, the supply cur-

P

rent drops down to about 3 mA.

A low ESR capacitor has much greater impact on performance
for C

than CO since current through CP is twice the CO cur-

P

rent. Therefore, the voltage drop due to C
the ESR of C

times the load current. While the ESR of C

P

is about four times

P

O

affects the output ripple voltage, the voltage drop generated by
the ESR of C
source resistance, determines the maximum available V

, combined with the voltage drop due to the output

P

10

ALUMINUM

1.0
CERAMIC

TANTALUM

ESR – V

0.1
ORGANIC SEMIC

0.01
–50 100

0

TEMPERATURE – 8C

50

OUT

.

Figure 13. ESR vs. Temperature

100

80

60

40

OUTPUT RIPPLE – mV

20

0

0

40 60 80 100 120 140

CAPACITANCE – mF

ADP3605-3

150mV

100mV

50mV

16020

Figure 14. Output Ripple Voltage (mV) vs. Capacitance
and ESR

Improved Load Regulation

In most applications, the IR drop from printed circuit board
traces is not critical. V

should be connected to the output

SENSE

at a convenient PCB location close to the load. However, if a
reduction in IR drop or improvement in load regulation is de­sired, the sense line can be used to monitor the output voltage
at the load. To avoid excessive noise pickup, keep the V

SENSE

line as short as possible and away from any noisy line.

Shutdown Mode

The ADP3605’s output can be disabled by pulling the SD pin
(Pin 4) high to a TTL/CMOS logic compatible level which will
stop the internal oscillator. In shutdown mode, the quiescent

current is reduced to 2 µA (typical). Applying a digital low level

or tying the SD Pin to ground will turn on the output. If the
shutdown feature is not used, Pin 4 should be tied to the
ground pin.

Power Dissipation

The power dissipation of the ADP3605 circuit must be limited
such that the junction temperature of the device does not exceed
the maximum junction temperature rating. Total power dissipa­tion is calculated as follows:

IN

–|V

Where I
and V

OUT

P = (V

and IS are output current and supply current, V

OUT

are input and output voltages respectively.

For example: assuming worst case conditions, V
V

= –2.9 V, I

OUT

= 120 mA and IS = 5 mA. Calculated

OUT

OUT

|) I

+ (VIN) I

OUT

S

= 6 V,

IN

IN

device power dissipation is:

P ≈ (6 V–|–2.9 V|)(0.12) + (6 V)(0.005 A) = 402 mW

This is far below the 660 mW power dissipation capability of the
ADP3605 in SO-8 or 600 mW in RU-14

General Board Layout Guidelines

Since the ADP3605’s internal switches turn on and off very fast,
good PC board layout practices are critical to ensure optimal
operation of the device. Improper layouts will result in poor load
regulation, especially under heavy loads. Following these simple
layout guidelines will improve output performance.

1. Use adequate ground and power traces or planes.

2. Use single point ground for device ground and input and
output capacitor grounds.

3. Keep external components as close to the device as possible.

4. Use short traces from the input and output capacitors
to the input and output pins respectively.

–6–

REV. A

ADP3605

ADP3605

V

IN

CP+
CP–

SD

V

SENSE

V

OUT

GND

+

C

P

4.7mF

C

IN

4.7mF

V

IN

= +5V

C

O

4.7mF

+

+

10mF

C1

4.7mF

D2

1N5817

D1
1N5817

+

+

R1

44.2kV

Maximum Output Voltage

Maximum unregulated output voltage can be obtained on the
ADP3605-3 by connecting the V
to the V

pin. Under this condition, the magnitude of the

OUT

unregulated output voltage depends on the load current. V

pin to ground instead of

SENSE

OUT

is inversely proportional to the load current as illustrated in
Figure 15.

–5.0

VIN = +5.0V

–4.0

– Volts

V

OUT

–3.0

0

20 40 60 80 100

ADP3605-3

LOAD CURRENT – mA

120

Figure 15. Maximum Unregulated Output Voltage

Regulated Adjustable Output Voltage

For the adjustable version of the ADP3605, the regulated out­put voltage is programmed by a resistor which is inserted be­tween the V

SENSE

and V

pins, as illustrated in Figure 16.

OUT

The inherent limit of the output voltage of a single inverting
charge pump stage is –1 times the input voltage. The inverse
(i.e., negative) scaling factor of 1.00 is reduced somewhat due to
losses that increase with output current. To increase the scaling
factor to attain a more negative output voltage, an external
pump stage can be added with just passive components as
shown in Figure 17. That single stage increases the inverse
scaling factor to a limit of two, although the diode drops will
limit the ability to attain that exact 2.00 scaling factor notice­ably. Even further increases can be achieved with more external
pump stages.

–5.0

V

R = 29k

High accuracy on the adjustable output voltage is achieved with
the use of precision trimmed internal resistors, which eliminates
the need to trim the external resistor or add a second resistor to
form a divider. The adjustable output voltage is set using the
following formula:

= –

1. 5

9.5 kΩ

R

where V

V

OUT

is in volts and R is in kΩ.

OUT

Regulated Dual Supply System

The circuit in Figure 18 provides regulated positive and negative
voltages for systems that require dual supplies from a single
battery or power supply.

Figure 17. Regulated –7 V from a 5 V Input

1N5817

V

IN

= +3.3V

10mF

ADP3607-5

V

V

IN

CP+
C

P

SD

OUT

V

SENSE

–

GND

+

C

+

P1

10mF

ADP3605

V

V

IN

C

10mF

OUT

CP+

+

P2

V

SENSE

C

–

P

SD

GND

16.5kV
1%

R1

+

C

O1

10mF

C

+

10mF

+5V

–2.6V

O2

Figure 18. Dual Supply System

–4.0

– Volts

OUT

V

VIN = +5.0V V

ADP3605

–3.0

0

20 40 60 80 100

Figure 16. Adjustable Regulated Output Voltage

OUT

R

LOAD CURRENT – mA

R = 24k

V

120

–7–REV. A

ADP3605

OUTLINE DIMENSIONS

Dimensions shown in inches and (mm).

0.1574 (4.00)

0.1497 (3.80)

0.0098 (0.25)

0.0040 (0.10)

SEATING

PLANE

8-Lead Small Outline IC

(SO-8)

0.1968 (5.00)

0.1890 (4.80)

8

5

0.2440 (6.20)

41

0.2284 (5.80)

PIN 1

0.0500
(1.27)

BSC

0.0688 (1.75)

0.0532 (1.35)

0.0192 (0.49)

0.0138 (0.35)

0.0098 (0.25)

0.0075 (0.19)

0.0196 (0.50)

0.0099 (0.25)

8°
0°

0.0500 (1.27)

0.0160 (0.41)

x 45°

14-Lead Thin Shrink Small Outline Package (TSSOP)

(RU-14)

0.201 (5.10)

0.193 (4.90)

0.177 (4.50)

0.169 (4.30)

0.006 (0.15)

0.002 (0.05)

SEATING

PLANE

14

1

PIN 1

0.0256
(0.65)

BSC

8

7

0.0118 (0.30)

0.0075 (0.19)

0.256 (6.50)

0.246 (6.25)

0.0433
(1.10)
MAX

0.0079 (0.20)

0.0035 (0.090)

88
08

0.028 (0.70)

0.020 (0.50)

C3325a–0–7/99

–8–

PRINTED IN U.S.A.

REV. A