Page 1
ADG441
ADG444
D4
S4
D3
S3
D2
S2
D1
S1
IN1
IN2
IN3
IN4
ADG442
D4
S4
D3
S3
D2
S2
D1
S1
IN1
IN2
IN3
IN4
SWITCHES SHOWN FOR A LOGIC "1" INPUT
One Technology Way, P.O. Box 9106, Norwood. MA 02062-9106, U.S.A.
Tel: 617/329-4700 Fax: 617/326-8703
REV. 0
Information furnished by Analog Devices is believed to be accurate and
reliable. However, no responsibility is assumed by Analog Devices for its
use, nor for any infringements of patents or other rights of third parties
which may result from its use. No license is granted by implication or
otherwise under any patent or patent rights of Analog Devices.
a
LC2MOS Quad SPST Switches
ADG441/ADG442/ADG444
FEATURES
44 V Supply Maximum Ratings
V
SS
to VDD Analog Signal Range
Low On Resistance (< 70 Ω)
Low ∆RON (9 Ω max)
Low R
ON
Match (3 Ω max)
Low Power Dissipation
Fast Switching Times
t
ON
< 110 ns
t
OFF
< 60 ns
Low Leakage Currents ( 3 nA max)
Low Charge Injection (6 pC max)
Break-Before-Make Switching Action
Latch-Up Proof
Plug-In Upgrade for
DG201A/ADG201A, DG202A/ADG202A,
DG211/ADG211A
Plug in Replacement for DG441/DG442/DG444
APPLICATIONS
Audio and Video Switching
Automatic Test Equipment
Precision Data Acquisition
Battery Powered Systems
Sample Hold Systems
Communication Systems
FUNCTIONAL BLOCK DIAGRAMS
GENERAL DESCRIPTION
The ADG441, ADG442 and ADG444 are monolithic CMOS
devices comprising four independently selectable switches. They
are designed on an enhanced LC
2
MOS process that provides
low power dissipation yet gives high switching speed and low on
resistance.
The on resistance profile is very flat over the full analog input
range ensuring good linearity and low distortion when switching
audio signals. High switching speed also makes the parts suitable for video signal switching. CMOS construction ensures
ultralow power dissipation making the parts ideally suited for
portable and battery powered instruments.
The ADG441, ADG442 and ADG444 contain four independent SPST switches. Each switch of the ADG441 and ADG444
turns on when a logic low is applied to the appropriate control
input. The ADG442 switches are turned on with a logic high on
the appropriate control input. The ADG441 and ADG444
switches differ in that the ADG444 requires a 5 V logic power
supply which is applied to the V
L
pin. The ADG441 and
ADG442 do not have a V
L
pin, the logic power supply being
generated internally by an on-chip voltage generator.
Each switch conducts equally well in both directions when ON
and has an input signal range that extends to the power supplies. In the OFF condition, signal levels up to the supplies are
blocked. All switches exhibit break-before-make switching action
for use in multiplexer applications. Inherent in the design is low
charge injection for minimum transients when switching the
digital inputs.
PRODUCT HIGHLIGHTS
1. Extended Signal Range
The ADG441/ADG442/ADG444 are fabricated on an enhanced LC
2
MOS, trench-isolated process, giving an in-
creased signal range that extends to the supply rails.
2. Low Power Dissipation
3. Low R
ON
4. Trench Isolation Guards Against Latch Up
A dielectric trench separates the P and N channel transistors
thereby preventing latch up even under severe overvoltage
conditions.
5. Break-Before-Make Switching
This prevents channel shorting when the switches are configured as a multiplexer.
6. Single Supply Operation
For applications where the analog signal is unipolar, the
ADG441/ADG442/ADG444 can be operated from a single
rail power supply. The parts are fully specified with a single
+12 V power supply.
Page 2
REV. 0
–2–
B Version T Version
–40°C to –55°C to
Parameter +25°C +85°C +25°C +125°C Units Test Conditions/Comments
ANALOG SWITCH
Analog Signal Range V
SS
to V
DD
VSS to V
DD
V
R
ON
40 40 Ω typ VD = ±8.5 V, IS = –10 mA
70 85 70 85 Ω max V
DD
= +13.5 V, VSS = –13.5 V
∆R
ON
44Ω typ –8.5 V ≤ VD ≤ +8.5 V
99Ω max
R
ON
Match 1 1 Ω typ VD = 0 V, IS = –10 mA
33Ω max
LEAKAGE CURRENTS V
DD
= +16.5 V, VSS = –16.5 V
Source OFF Leakage I
S
(OFF) ±0.01 ±0.01 nA typ VD = ±15.5 V, VS = 715.5 V;
±0.5 ±3 ±0.5 ±20 nA max Test Circuit 2
Drain OFF Leakage I
D
(OFF) ±0.01 ±0.01 nA typ VD = ±15.5 V, VS = 715.5 V;
±0.5 ±3 ±0.5 ±20 nA max Test Circuit 2
Channel ON Leakage I
D
, IS (ON) ±0.08 ±0.08 nA typ VS = VD = ±15.5 V;
±0.5 ±3 ±0.5 ±40 nA max Test Circuit 3
DIGITAL INPUTS
Input High Voltage, V
INH
2.4 2.4 V min
Input Low Voltage, V
INL
0.8 0.8 V max
Input Current
I
INL
or I
INH
±0.00001 ±0.00001 µA typ VIN = V
INL
or V
INH
±0.5 ±0.5 µA max
DYNAMIC CHARACTERISTICS
2
t
ON
85 85 ns typ RL = 1 kΩ, CL = 35 pF;
110 170 110 170 ns max V
S
= ±10 V; Test Circuit 4
t
OFF
45 45 ns typ RL = 1 kΩ, CL = 35 pF;
60 80 60 80 ns max V
S
= ±10 V; Test Circuit 4
t
OPEN
30 30 ns typ RL = 1 kΩ, CL = 35 pF;
Charge Injection 1 1 pC typ V
S
= 0 V, RS = 0 Ω, CL= 1 nF;
6 6 pC max V
DD
= +15 V, VSS = –15 V;
Test Circuit 5
OFF Isolation 60 60 dB typ R
L
= 50 Ω, CL = 5 pF;
f = 1 MHz; Test Circuit 6
Channel-to-Channel Crosstalk 100 100 dB typ R
L
= 50 Ω, CL = 5 pF;
f = 1 MHz; Test Circuit 7
C
S
(OFF) 4 4 pF typ f = 1 MHz
C
D
(OFF) 4 4 pF typ f = 1 MHz
CD, CS (ON) 16 16 pF typ f = 1 MHz
POWER REQUIREMENTS V
DD
= +16.5 V, VSS = –16.5 V
I
DD
Digital Inputs = 0 V or 5 V
ADG441/ADG442 80 80 µA max
ADG444 0.001 0.001 µA typ
1 2.5 1 2.5 µA max
I
SS
0.0001 0.0001 µA typ
1 2.5 1 2.5 µA max
I
L
(ADG444 Only) 0.001 0.001 µA typ VL = +5.5 V
1 2.5 1 2.5 µA max
NOTES
1
Temperature ranges are as follows: B Versions: –40°C to +85°C; T Versions: –55°C to +125°C.
2
Guaranteed by design, not subject to production test.
Specifications subject to change without notice.
ADG441/ADG442/ADG444–SPECIFICATIONS
1
Dual Supply
(V
DD
= +15 V ± 10%, V
SS
= –15 V ± 10%, VL = +5 V ± 10% (ADG444), GND = 0 V, unless otherwise noted)
Page 3
ORDERING GUIDE
Model
1
Temperature Range Package Option
2
ADG441BN –40°C to +85°C N-16
ADG441BR –40°C to +85°C R-16A
ADG441TQ –55°C to +125°C Q-16
ADG442BN –40°C to +85°C N-16
ADG442BR –40°C to +85°C R-16A
ADG444BN –40°C to +85°C N-16
ADG444BR –40°C to +85°C R-16A
N
OTES
1
To order MIL-STD-883, Class B processed parts, add /883B to T grade part
numbers.
2
N = Plastic DIP, R = 0.15" Small Outline IC (SOIC), Q = Cerdip.
REV. 0
–3–
ADG441/ADG442/ADG444
Table I. Truth Table
ADG441/ADG444 ADG442 Switch
IN IN Condition
01ON
1 0 OFF
B Version T Version
–40°C to –55°C to
Parameter +25°C +85°C +25°C +125°C Units Test Conditions/Comments
ANALOG SWITCH
Analog Signal Range 0 to V
DD
0 to V
DD
V
R
ON
70 70 Ω typ VD = +3 V, +8 V, IS = –10 mA;
110 130 110 130 Ω max V
DD
= +10.8 V
∆R
ON
44Ω typ +3 V ≤ VD ≤ +8 V
99Ω max
R
ON
Match 1 1 Ω typ VD = 6 V, IS = –10 mA
33Ω max
LEAKAGE CURRENT V
DD
= +13.2 V
Source OFF Leakage I
S
(OFF) ±0.01 ± 0.01 nA typ VD = 12.2 V/1 V, VS = 1 V/12.2 V;
± 0.5 ± 3 ± 0.5 ± 20 nA max Test Circuit 2
Drain OFF Leakage I
D
(OFF) ±0.01 ± 0.01 nA typ VD = 12.2 V/1 V, VS = 1 V/12.2 V;
± 0.5 ± 3 ± 0.5 ± 20 nA max Test Circuit 2
Channel ON Leakage I
D
, IS (ON) ±0.08 ±0.08 nA typ VS = VD = 12.2 V/1 V;
±0.5 ±3 ±0.5 ± 40 nA max Test Circuit 3
DIGITAL INPUTS
Input High Voltage, V
INH
2.4 2.4 V min
Input Low Voltage, V
INL
0.8 0.8 V max
Input Current
I
INL
or I
INH
±0.00001 ±0.00001 µA typ VIN = V
INL
or V
INH
±0.5 ±0.5 µA max
DYNAMIC CHARACTERISTICS
2
t
ON
105 105 ns typ RL = 1 kΩ, CL = 35 pF;
150 220 150 220 ns max V
S
= +8 V; Test Circuit 4
t
OFF
40 40 ns typ RL = 1 kΩ, CL = 35 pF;
60 100 60 100 ns max V
S
= +8 V; Test Circuit 4
t
OPEN
50 50 ns typ RL = 1 kΩ, CL = 35 pF;
Charge Injection 2 2 pC typ V
S
= 6 V, RS = 0 Ω, CL = 1 nF;
6 6 pC max V
DD
= +12 V, VSS = 0 V;
Test Circuit 5
OFF Isolation 60 60 dB typ R
L
= 50 Ω,CL= 5 pF, f = 1 MHz;
Test Circuit 6
Channel-to-Channel Crosstalk 100 100 dB typ R
L
=50Ω,CL= 5 pF, f = 1 MHz;
Test Circuit 7
C
S
(OFF) 7 7 pF typ f = 1 MHz
C
D
(OFF) 10 10 pF typ f = 1 MHz
CD, CS (ON) 16 16 pF typ f = 1 MHz
POWER REQUIREMENTS V
DD
= +13.2 V
I
DD
Digital Inputs = 0 V or 5 V
ADG441/ADG442 80 80 µA max
ADG444 0.001 0.001 µA typ
1 2.5 1 2.5 µA max
I
L
(ADG444 Only) 0.001 0.001 µA typ VL = +5.5 V
1 2.5 1 2.5 µA max
NOTES
1
Temperature ranges are as follows: B Versions: –40°C to +85°C; T Versions: –55°C to +125°C.
2
Guaranteed by design, not subject to production test.
Specifications subject to change without notice.
Single Supply
(V
DD
= +12 V ± 10%, V
SS
= 0 V, VL = +5 V ± 10% (ADG444), GND = 0 V, unless otherwise noted)
Page 4
ADG441/ADG442/ADG444
REV. 0
–4–
ABSOLUTE MAXIMUM RATINGS
1
(TA = +25°C unless otherwise noted)
VDD to VSS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .+44 V
V
DD
to GND . . . . . . . . . . . . . . . . . . . . . . . . . . –0.3 V to +25 V
V
SS
to GND . . . . . . . . . . . . . . . . . . . . . . . . . . . +0.3 V to –25 V
V
L
to GND . . . . . . . . . . . . . . . . . . . . . . –0.3 V to VDD + 0.3 V
Analog, Digital Inputs
2
. . . . . . . . . . . . VSS – 2 V to VDD + 2 V
or 30 mA, Whichever Occurs First
Continuous Current, S or D . . . . . . . . . . . . . . . . . . . . . 30 mA
Peak Current, S or D . . . . . . . . . . . . . . . . . . . . . . . . . . 100 mA
(Pulsed at 1 ms, 10% Duty Cycle Max)
Operating Temperature Range
Industrial (B Version) . . . . . . . . . . . . . . . . . .–40°C to +85°C
Extended (T Version) . . . . . . . . . . . . . . . .–55°C to +125°C
Storage Temperature Range . . . . . . . . . . . . . –65°C to +150°C
Junction Temperature . . . . . . . . . . . . . . . . . . . . . . . . . +150°C
Cerdip Package, Power Dissipation . . . . . . . . . . . . . . .900 mW
θ
JA
, Thermal Impedance . . . . . . . . . . . . . . . . . . . . . . . 76°C/W
Lead Temperature, Soldering (10 sec) . . . . . . . . . . . . . +300°C
Plastic Package, Power Dissipation . . . . . . . . . . . . . . . 470 mW
θ
JA
, Thermal Impedance . . . . . . . . . . . . . . . . . . . . . . 177°C/W
Lead Temperature, Soldering (10 sec) . . . . . . . . . . . . . +260°C
SOIC Package, Power Dissipation . . . . . . . . . . . . . . . .600 mW
θ
JA
, Thermal Impedance . . . . . . . . . . . . . . . . . . . . . . . 77°C/W
Lead Temperature, Soldering
Vapor Phase (60 sec) . . . . . . . . . . . . . . . . . . . . . . . . +215°C
Infrared (15 sec) . . . . . . . . . . . . . . . . . . . . . . . . . . . . +220°C
NOTES
1
Stresses above those listed under “Absolute Maximum Ratings” may cause
permanent damage to the device. This is a stress rating only and functional
operation of the device at these or any other conditions above those listed in the
operational sections of this specification is not implied. Exposure to absolute
maximum rating conditions for extended periods may affect device reliability. Only
one absolute maximum rating may be applied at any one time.
2
Overvoltages at IN, S or D will be clamped by internal diodes. Current should be
limited to the maximum ratings given.
ADG441/ADG442 PIN CONFIGURATION (DIP/SOIC)
NC = NO CONNECT
IN1
D1
IN2
D2
GND
S4
D4
NC
S3
D3
S1
V
SS
S2
V
DD
IN4 IN3
1
2
16
15
5
6
7
12
11
10
3
4
14
13
89
TOP VIEW
(Not to Scale)
ADG441
ADG442
ADG444 PIN CONFIGURATION (DIP/SOIC)
TERMINOLOGY
V
DD
Most Positive Power Supply Potential.
V
SS
Most Negative Power Supply Potential in dual
supplies. In single supply applications, it may be
connected to ground.
V
L
Logic Power Supply (+5 V).
GND Ground (0 V) Reference.
S Source Terminal. May be an input or output.
D Drain Terminal. May be an input or output.
IN Logic Control Input.
R
ON
Ohmic resistance between D and S.
R
ON
Match Difference between the RON of any two channels.
I
S
(OFF) Source leakage current with the switch “OFF.”
I
D
(OFF) Drain leakage current with the switch “OFF.”
I
D
, IS (ON) Channel leakage current with the switch “ON.”
V
D
(VS) Analog voltage on terminals D, S.
C
S
(OFF) “OFF” Switch Source Capacitance.
C
D
(OFF) “OFF” Switch Drain Capacitance.
C
D
, CS (ON) “ON” Switch Capacitance.
t
ON
Delay between applying the digital control
input and the output switching on.
t
OFF
Delay between applying the digital control
input and the output switching off.
t
OPEN
Break-Before-Make Delay when switches are
configured as a multiplexer.
Crosstalk A measure of unwanted signal which is coupled
through from one channel to another as a result
of parasitic capacitance.
Off Isolation A measure of unwanted signal coupling through
an “OFF” switch.
Charge A measure of the glitch impulse transferred from
Injection the digital input to the analog output during
switching.
CAUTION
ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily
accumulate on the human body and test equipment and can discharge without detection.
Although these devices feature proprietary ESD protection circuitry, permanent damage may
occur on devices subjected to high energy electrostatic discharges. Therefore, proper ESD
precautions are recommended to avoid performance degradation or loss of functionality.
WARNING!
ESD SENSITIVE DEVICE
IN1
D1
IN2
D2
GND
S4
D4
V
L
S3
D3
S1
V
SS
S2
V
DD
IN4 IN3
1
2
16
15
5
6
7
12
11
10
3
4
14
13
89
TOP VIEW
(Not to Scale)
ADG444
Page 5
ADG441/ADG442/ADG444
REV. 0
–5–
TRENCH ISOLATION
In the ADG441, ADG442 and ADG444, an insulating oxide
layer (trench) is placed between the NMOS and the PMOS
transistors of each CMOS switch. Parasitic junctions, which occur between the transistors in junction isolated switches, are
eliminated, the result being a completely latch-up proof switch.
In junction isolation, the N and P wells of the PMOS and
NMOS transistors form a diode that is reverse-biased under
normal operation. However, during overvoltage conditions, this
diode becomes forward biased. A silicon-controlled rectifier
(SCR) type circuit is formed by the two transistors causing a significant amplification of the current which, in turn, leads to
latch up. With trench isolation, this diode is removed, the result
being a latch-up proof switch.
Trench isolation also leads to lower leakage currents. The
ADG441, ADG442 and ADG444 have a leakage current
of 0.5 nA as compared with a leakage current of several
nanoamperes in non-trench isolated switches. Leakage current is
an important parameter in sample-and-hold circuits, this current
being responsible for the discharge of the holding capacitor with
time causing droop. The ADG441/ADG442/ADG444’s low
leakage current, along with its fast switching speeds, make it
suitable for fast and accurate sample-and-hold circuits.
Typical Performance Characteristics
NMOS PMOS
P-WELL N-WELL
BURIED OXIDE LAYER
SUBSTRATE (BACK GATE)
TRENCH
LOCOS
Figure 1. Trench Isolation
170
10
15
90
50
30
130
9
R
ON
– Ω
VD (V
S)
– Volts
612
T
A
= +25°C
150
110
70
30
VDD = +5V
VSS = 0V
V
DD
= +10V
VSS = 0V
V
DD
= +12V
VSS = 0V
V
DD
= +15V
VSS = 0V
100
20
15
60
40
–10–15
80
100
R
ON
– Ω
VD (V
S)
– Volts
–5 5
TA = +25°C
VDD = +5V
V
SS
= –5V
V
DD
= +12V
V
SS
= –12V
V
DD
= +15V
V
SS
= –15V
V
DD
= +10V
V
SS
= –10V
Figure 3. RON as a Function of VD (VS): Single SupplyFigure 2. RON as a Function of VD (VS): Dual Supply
Page 6
ADG441/ADG442/ADG444
REV. 0
–6–
100
20
–15 15
80
40
–10
60
5100–5
+125°C
+25°C
+85°C
VDD = +15V
V
SS
= –15V
R
ON
– Ω
VD (VS) – Volts
Figure 4. RON as a Function of VD (VS) for Different
Temperatures
0.02
–0.02
15
–0.01
–10–15
0.00
0.01
1050–5
VS, VD – Volts
LEAKAGE CURRENT – nA
VDD = +15V
VSS = –15V
TA = +25°C
IS (OFF)
ID (OFF)
ID (ON)
Figure 5. Leakage Currents as a Function of VS (VD)
120
50
10M
60
1k
90
110
1M100k10k
FREQUENCY – Hz
dB
100
70
80
VDD = +15V
V
SS
= –15V
CROSSTALK
OFF ISOLATION
Figure 6. Crosstalk and Off Isolation vs. Frequency
120
20
012
80
40
2
60
81064
V
D
(VS) – Volts
R
ON
– Ω
+25°C
100
VDD = +12V
V
SS
= 0V
+85°C
+125°C
Figure 7. RON as a Function of VD (VS) for Different
Temperatures
0.010
–0.010
12
–0.005
20
0.000
0.005
10864
VS, VD – Volts
LEAKAGE CURRENT – nA
VDD = +12V
VSS = 0V
T
A
= +25°C
ID (ON)
IS (OFF)
ID (OFF)
Figure 8. Leakage Currents as a Function of VS (VD)
20
–20
15
–10
–6–15 960–9
V
S
– Volts
Q – pC
10
0
–12 –3 3 12
CL = 1nF
VDD = +15V
V
SS
= –15V
VDD = +12V
V
SS
= 0V
Figure 9. Charge Injection vs. Source Voltage
Page 7
ADG441/ADG442/ADG444
REV. 0
–7–
120
40
±20
80
60
±12±10
100
±16
t
– ns
SUPPLY VOLTAGE – Volts
±14 ±18
VIN = +8V
t
ON
t
OFF
Figure 10. Switching Time vs. Bipolar Supply
160
20
20
40
108
100
140
18161412
SUPPLY VOLTAGE – Volts
t
– ns
120
60
80
VIN = +8V
t
ON
t
OFF
Figure 11. Switching Time vs. Single Supply
Test Circuits
V1
I
DS
SD
V
S
RON = V1/I
DS
Test Circuit 1. On Resistance
Test Circuit 3. On Leakage
Test Circuit 2. Off Leakage
SD
V
S
A A
V
D
ID (OFF)IS (OFF)
SD
V
S
A
V
D
ID (ON)
S
D
V
S
IN
GND
V
SS
0.1µF
–15V
R
L
1kΩ
C
L
35pF
V
OUT
0.1µF 0.1µF
V
DDVL
+15V
+5V
t
OFF
90%90%
50% 50%
50% 50%
3V
ADG442
ADG441/ADG444
V
IN
V
IN
V
OUT
3V
t
ON
Test Circuit 4. Switching Times
Page 8
ADG441/ADG442/ADG444
REV. 0
–8–
PRINTED IN U.S.A.
C1890–18–4/94
S
D
V
S
IN
GND
V
SS
–15V
C
L
1nF
V
OUT
VDDV
L
+15V +5V
R
S
3V
V
IN
V
OUT
∆V
OUT
Q
INJ
= CL × ∆V
OUT
Test Circuit 5. Charge Injection
S
D
V
S
IN
GND
V
SS
0.1µF
–15V
R
L
50Ω
V
OUT
0.1µF 0.1µF
VDDV
L
+15V +5V
V
IN
Test Circuit 6. Off Isolation
S
D
V
S
GND
V
SS
0.1µF
–15V
0.1µF 0.1µF
V
DDVL
+15V +5V
V
IN1
S
V
IN2
NC
50Ω
V
OUT
R
L
50Ω
CHANNEL-TO-CHANNEL CROSSTALK = 20 × LOG V
S/VOUT
Test Circuit 7. Channel-to-Channel Crosstalk
OUTLINE DIMENSIONS
Dimensions shown in inches and (mm).
Plastic DIP (N-16)
0.011
(0.28)
0.18
(4.57)
MAX
0.3 (7.62)
PIN 1
18
916
0.25
(6.35)
0.31
(7.87)
0.87 (22.1) MAX
0.125
(3.18)
MIN
0.035
(0.89)
0.18 (4.57)
SEATING
PLANE
0.018 (0.46) 0.033 (0.84) 0.1 (2.54)
BSC
Small Outline IC (R-16A)
8
916
0.2440 (6.20)
0.2284 (5.80)
0.1574 (4.00)
0.1497 (3.80)
PIN 1
1
0.0688 (1.75)
0.0532 (1.35)
0.3937 (10.00)
0.3859 (9.80)
0.0500 (1.27)
BSC
SEATING
PLANE
0.0098 (0.25)
0.0040 (0.10)
0.0192 (0.49)
0.0138 (0.35)
0° – 8°
0.0099 (0.25)
0.0075 (0.19)
× 45°
0.0196 (0.50)
0.0099 (0.25)
0.0500 (1.27)
0.0160 (0.41)
Cerdip (Q-16)
0.015 (0.381)
0.008 (0.204)
0.320 (8.13)
0.290 (7.37)
PIN 1
0.310 (7.87)
0.220 (5.59)
1
8
9
16
0.840 (21.34) MAX
0.060 (1.52)
0.015 (0.38)
0.150
(3.81)
MIN
0.200
(5.08)
MAX
PLANE
SEATING
0.022 (0.558)
0.014 (0.356)
0.100 (2.54)
BSC
0.070 (1.78)
0.30 (0.76)
Page 9
ADG441/ADG442/ADG444
REV. 0
–9–
ORDERING GUIDE
Model
1
Temperature Range Package Option
2
ADG441BN –40°C to +85°C N-16
ADG441BR –40°C to +85°C R-16A
ADG441TQ –55°C to +125°C Q-16
ADG442BN –40°C to +85°C N-16
ADG442BR –40°C to +85°C R-16A
ADG444BN –40°C to +85°C N-16
ADG444BR –40°C to +85°C R-16A
NOTES
1
To order MIL-STD-883, Class B processed parts, add /883B to T grade part
numbers.
2
N = Plastic DIP, R = 0.15" Small Outline IC (SOIC), Q = Cerdip. For outline
information see Package Information section.
FOR CATALOG
Loading...