Datasheet AD9762ARU, AD9762AR, AD9762-EB Datasheet (Analog Devices)

Page 1
12-Bit, 125 MSPS
(
)
a
FEATURES Member of Pin-Compatible TxDAC Product Family 125 MSPS Update Rate 12-Bit Resolution Excellent Spurious Free Dynamic Range Performance SFDR to Nyquist @ 5 MHz Output: 70 dBc Differential Current Outputs: 2 mA to 20 mA Power Dissipation: 175 mW @ 5 V to 45 mW @ 3 V Power-Down Mode: 25 mW @ 5 V On-Chip 1.20 V Reference Single +5 V or +3 V Supply Operation Package: 28-Lead SOIC and TSSOP Edge-Triggered Latches
APPLICATIONS Communication Transmit Channel:
Basestations (Single/Multichannel Applications)
ADSL/HFC Modems Direct Digital Synthesis (DDS) Instrumentation

PRODUCT DESCRIPTION

The AD9762 is the 12-bit resolution member of the TxDAC series of high performance, low power CMOS digital-to-analog converters (DACs). The TxDAC compatible 8-, 10-, 12-, and 14-bit DACs is specifically opti­mized for the transmit signal path of communication systems. All of the devices share the same interface options, small outline package and pinout, thus providing an upward or downward component selection path based on performance, resolution and cost. The AD9762 offers exceptional ac and dc performance while supporting update rates up to 125 MSPS.
The AD9762’s flexible single-supply operating range of 2.7 V to
5.5 V and low power dissipation are well suited for portable and low power applications. Its power dissipation can be further reduced to a mere 45 mW without a significant degradation in performance by lowering the full-scale current output. Also, a power-down mode reduces the standby power dissipation to approximately 25 mW.
The AD9762 is manufactured on an advanced CMOS process. A segmented current source architecture is combined with a proprietary switching technique to reduce spurious components and enhance dynamic performance. Edge-triggered input latches and a 1.2 V temperature compensated bandgap refer­ence have been integrated to provide a complete monolithic DAC solution. Flexible supply options support +3 V and +5 V CMOS logic families.
The AD9762 is a current-output DAC with a nominal full-scale output current of 20 mA and > 100 kΩ output impedance.
TxDAC is a registered trademark of Analog Devices, Inc. *Patent pending.
REV. B
Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
family which consists of pin
®
TxDAC
D/A Converter
AD9762*

FUNCTIONAL BLOCK DIAGRAM

+5V
0.1␮F
REFLO
+1.20V REF
REFIO
FS ADJ
DVDD
DCOM
CLOCK
SLEEP
SEGMENTED
SWITCHES
DIGITAL DATA INPUTS
R
SET
CLOCK
0.1␮F
+5V
Differential current outputs are provided to support single­ended or differential applications. Matching between the two current outputs ensures enhanced dynamic performance in a differential output configuration. The current outputs may be tied directly to an output resistor to provide two complemen­tary, single-ended voltage outputs or fed directly into a trans­former. The output voltage compliance range is 1.25 V.
The on-chip reference and control amplifier are configured for maximum accuracy and flexibility. The AD9762 can be driven by the on-chip reference or by a variety of external reference voltages. The internal control amplifier which provides a wide (>10:1) adjustment span allows the AD9762 full-scale current to be adjusted over a 2 mA to 20 mA range while maintaining excellent dynamic performance. Thus, the AD9762 may oper­ate at reduced power levels or be adjusted over a 20 dB range to provide additional gain ranging capabilities.
The AD9762 is available in 28-lead SOIC and TSSOP pack­ages. It is specified for operation over the industrial tempera­ture range.

PRODUCT HIGHLIGHTS

1. The AD9762 is a member of the TxDAC product family which provides an upward or downward component selection path based on resolution (8 to 14 bits), performance and cost.
2. Manufactured on a CMOS process, the AD9762 uses a pro­prietary switching technique that enhances dynamic perfor­mance beyond what was previously attainable by higher power/cost bipolar or BiCMOS devices.
3. On-chip, edge-triggered input CMOS latches interface readily to +3 V and +5 V CMOS logic families. The AD9762 can support update rates up to 125 MSPS.
4. A flexible single-supply operating range of 2.7 V to 5.5 V and a wide full-scale current adjustment span of 2 mA to 20 mA allow the AD9762 to operate at reduced power levels.
5. The current output(s) of the AD9762 can be easily config­ured for various single-ended or differential circuit topologies.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A. Tel: 781/329-4700 World Wide Web Site: http://www.analog.com Fax: 781/326-8703 © Analog Devices, Inc., 2000
50pF
LATCHES
COMP1
CURRENT
SOURCE
ARRAY
SWITCHES
AVDD ACOM
AD9762
LSB
DB11–DB0
COMP2
IOUTA
IOUTB
0.1␮F
Page 2
AD9762–SPECIFICATIONS
(T
to T
DC SPECIFICATIONS
MIN
, AVDD = +5 V, DVDD = +5 V, I
MAX
Parameter Min Typ Max Units
RESOLUTION 12 Bits
DC ACCURACY
1
Integral Linearity Error (INL)
= +25°C –2.5 ± 0.75 +2.5 LSB
T
A
T
MIN
to T
MAX
–4.0 ± 1.0 +4.0 LSB
Differential Nonlinearity (DNL)
= +25°C –1.5 ± 0.5 +1.5 LSB
T
A
T
MIN
to T
MAX
–2.0 ± 0.75 +2.0 LSB
ANALOG OUTPUT
Offset Error –0.025 +0.025 % of FSR Gain Error Gain Error Full-Scale Output Current
(Without Internal Reference) –10 ±2 +10 % of FSR (With Internal Reference) –10 ±1 +10 % of FSR
2
2.0 20.0 mA
Output Compliance Range –1.0 +1.25 V Output Resistance 100 k Output Capacitance 5 pF
REFERENCE OUTPUT
Reference Voltage 1.08 1.20 1.32 V Reference Output Current
3
REFERENCE INPUT
Input Compliance Range 0.1 1.25 V Reference Input Resistance 1 M Small Signal Bandwidth (w/o C
COMP1
4
)
TEMPERATURE COEFFICIENTS
Offset Drift 0 ppm of FSR/°C Gain Drift Gain Drift
(Without Internal Reference) ±50 ppm of FSR/°C (With Internal Reference) ±100 ppm of FSR/°C
Reference Voltage Drift ±50 ppm/°C
POWER SUPPLY
Supply Voltages
AVDD
5
2.7 5.0 5.5 V
DVDD 2.7 5.0 5.5 V Analog Supply Current (I Digital Supply Current (I Supply Current Sleep Mode (I Power Dissipation Power Dissipation Power Dissipation
6
(5 V, I
7
(5 V, I
7
(3 V, I
)2530mA
AVDD
6
)
DVDD
OUTFS
OUTFS
OUTFS
) 8.5 mA
AVDD
= 20 mA) 133 160 mW = 20 mA) 190 mW
= 2 mA) 45 mW Power Supply Rejection Ratio—AVDD –0.4 +0.4 % of FSR/V Power Supply Rejection Ratio—DVDD –0.025 +0.025 % of FSR/V
OPERATING RANGE –40 +85 °C
NOTES
1
Measured at IOUTA, driving a virtual ground.
2
Nominal full-scale current, I
3
Use an external buffer amplifier to drive any external load.
4
Reference bandwidth is a function of external cap at COMP1 pin and signal level. Refer to Figure 41.
5
For operation below 3 V, it is recommended that the output current be reduced to 12 mA or less to maintain optimum performance.
6
Measured at f
7
Measured as unbuffered voltage output into 50 Ω R
Specifications subject to change without notice.
= 25 MSPS and f
CLOCK
, is 32 × the I
OUTFS
= 1.0 MHz.
OUT
current.
REF
at IOUTA and IOUTB, f
LOAD
CLOCK
= 20 mA, unless otherwise noted)
OUTFS
100 nA
1.4 MHz
1.5 2 mA
= 100 MSPS and f
= 40 MHz.
OUT
–2–
REV. B
Page 3
AD9762
(T
to T
, AVDD = +5 V, DVDD = +5 V, I
MAX
DYNAMIC SPECIFICATIONS
MIN
50 Doubly Terminated, unless otherwise noted)
Parameter Min Typ Max Units
DYNAMIC PERFORMANCE
Maximum Output Update Rate (f Output Settling Time (t Output Propagation Delay (t
) (to 0.1%)
ST
)1ns
PD
Glitch Impulse 5 pV-s Output Rise Time (10% to 90%) Output Fall Time (10% to 90%) Output Noise (I Output Noise (I
= 20 mA) 50 pA/Hz
OUTFS
= 2 mA) 30 pA/Hz
OUTFS
) 125 MSPS
CLOCK
1
1
1
AC LINEARITY
Spurious-Free Dynamic Range to Nyquist
f
= 25 MSPS; f
CLOCK
= +25°C 75 79 dBc
T
A
T
to T
f
CLOCK
f
CLOCK
f
CLOCK
f
CLOCK
f
CLOCK
f
CLOCK
f
CLOCK
f
CLOCK
MIN
MAX
= 50 MSPS; f = 50 MSPS; f = 50 MSPS; f = 50 MSPS; f = 100 MSPS; f = 100 MSPS; f = 100 MSPS; f = 100 MSPS; f
= 1.00 MHz
OUT
73 dBc
= 1.00 MHz 79 dBc
OUT
= 2.51 MHz 74 dBc
OUT
= 5.02 MHz 70 dBc
OUT
= 20.2 MHz 57 dBc
OUT
= 2.51 MHz 73 dBc
OUT
= 5.04 MHz 67 dBc
OUT
= 20.2 MHz 57 dBc
OUT
= 40.4 MHz 53 dBc
OUT
Spurious-Free Dynamic Range within a Window
f
= 25 MSPS; f
CLOCK
= +25°C 78 86 dBc
T
A
T
to T
f
CLOCK
f
CLOCK
MIN
MAX
= 50 MSPS; f = 100 MSPS; f
=1.00 MHz; 2 MHz Span
OUT
76 dBc
= 5.02 MHz; 2 MHz Span 84 dBc
OUT
= 5.04 MHz; 4 MHz Span 84 dBc
OUT
Total Harmonic Distortion
f
= 25 MSPS; f
CLOCK
= +25°C –78 –74 dBc
T
A
T
to T
f
CLOCK
f
CLOCK
MIN
MAX
= 50 MHz; f = 100 MHz; f
= 1.00 MHz
OUT
= 2.00 MHz –75 dBc
OUT
= 2.00 MHz –75 dBc
OUT
Multitone Power Ratio (8 Tones at 110 kHz Spacing)
f
= 20 MSPS; f
CLOCK
NOTES
1
Measured single ended into 50 load.
Specifications subject to change without notice.
= 2.00 MHz to 2.99 MHz 73 dBc
OUT
= 20 mA, Differential Transformer Coupled Output,
OUTFS
35 ns
2.5 ns
2.5 ns
–72 dBc
REV. B
–3–
Page 4
AD9762
(T
to T
DIGITAL SPECIFICATIONS
MIN
, AVDD = +5 V, DVDD = +5 V, I
MAX
Parameter Min Typ Max Units
DIGITAL INPUTS
Logic “1” Voltage @ DVDD = +5 V 3.5 5 V Logic “1” Voltage @ DVDD = +3 V 2.1 3 V Logic “0” Voltage @ DVDD = +5 V 0 1.3 V Logic “0” Voltage @ DVDD = +3 V 0 0.9 V Logic “1” Current –10 +10 µA Logic “0” Current –10 +10 µA Input Capacitance 5 pF Input Setup Time (t Input Hold Time (t Latch Pulsewidth (t
Specifications subject to change without notice.
) 2.0 ns
S
) 1.5 ns
H
) 3.5 ns
LPW
DB0–DB11
= 20 mA unless otherwise noted)
OUTFS
t
S
CLOCK
t
PD
IOUTA
OR
IOUTB
Figure 1. Timing Diagram
ABSOLUTE MAXIMUM RATINGS*
With
Parameter Respect to Min Max Units
AVDD ACOM –0.3 +6.5 V DVDD DCOM –0.3 +6.5 V ACOM DCOM –0.3 +0.3 V AVDD DVDD –6.5 +6.5 V CLOCK, SLEEP DCOM –0.3 DVDD + 0.3 V Digital Inputs DCOM –0.3 DVDD + 0.3 V IOUTA, IOUTB ACOM –1.0 AVDD + 0.3 V COMP1, COMP2 ACOM –0.3 AVDD + 0.3 V REFIO, FSADJ ACOM –0.3 AVDD + 0.3 V REFLO ACOM –0.3 +0.3 V Junction Temperature +150 °C Storage Temperature –65 +150 °C Lead Temperature
(10 sec) +300 °C
*Stresses above those listed under Absolute Maximum Ratings may cause perma-
nent damage to the device. This is a stress rating only; functional operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum ratings for extended periods may effect device reliability.
t
H
t
LPW
t
ST
0.1%
0.1%

ORDERING GUIDE

Temperature Package Package
Model Range Description Option*
AD9762AR –40°C to +85°C 28-Lead 300 mil SOIC R-28 AD9762ARU –40°C to +85°C 28-Lead TSSOP RU-28 AD9762-EB Evaluation Board
*R = SOIC, RU = TSSOP.
THERMAL CHARACTERISTICS Thermal Resistance
28-Lead 300 mil SOIC
= 71.4°C/W
θ
JA
θ
= 23°C/W
JC
28-Lead TSSOP
= 97.9°C/W
θ
JA
θ
= 14.0°C/W
JC
CAUTION
ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily accumulate on the human body and test equipment and can discharge without detection. Although the AD9762 features proprietary ESD protection circuitry, permanent damage may occur on devices subjected to high energy electrostatic discharges. Therefore, proper ESD precautions are recommended to avoid performance degradation or loss of functionality.
–4–
WARNING!
ESD SENSITIVE DEVICE
REV. B
Page 5
PIN CONFIGURATION
AD9762
(MSB) DB11
1
2
DB10
DB9
3
DB8
4
DB7
5
6
DB6
DB5
7
8
DB4
9
DB3
10
DB2
11
DB1
DB0
12
NC
13
NC
14
NC = NO CONNECT
AD9762
TOP VIEW
(Not to Scale)
28
27
26
25
24
23
22
21
20
19
18
17
16
15
CLOCK
DVDD
DCOM
NC
AVDD
COMP2
IOUTA
IOUTB
ACOM
COMP1
FS ADJ
REFIO
REFLO
SLEEP
PIN DESCRIPTIONS
Pin No. Name Description
1 DB11 Most Significant Data Bit (MSB). 2–11 DB10–DB1 Data Bits 1–10. 12 DB0 Least Significant Data Bit (LSB). 13, 14, 25 NC No Internal Connection. 15 SLEEP Power-down Control Input. Active High. Contains active pull-down circuit, thus may be left unterminated if
not used. 16 REFLO Reference Ground when Internal 1.2 V Reference Used. Connect to AVDD to disable internal reference. 17 REFIO Reference Input/Output. Serves as reference input when internal reference disabled (i.e., Tie REFLO to
AVDD). Serves as 1.2 V reference output when internal reference activated (i.e., Tie REFLO to ACOM).
Requires 0.1 µF capacitor to ACOM when internal reference activated. 18 FS ADJ Full-Scale Current Output Adjust. 19 COMP1 Bandwidth/Noise Reduction Node. Add 0.1 µF to AVDD for optimum performance. 20 ACOM Analog Common. 21 IOUTB Complementary DAC Current Output. Full-scale current when all data bits are 0s. 22 IOUTA DAC Current Output. Full-scale current when all data bits are 1s. 23 COMP2 Internal Bias Node for Switch Driver Circuitry. Decouple to ACOM with 0.1 µF capacitor. 24 AVDD Analog Supply Voltage (+2.7 V to +5.5 V). 26 DCOM Digital Common. 27 DVDD Digital Supply Voltage (+2.7 V to +5.5 V). 28 CLOCK Clock Input. Data latched on positive edge of clock.
REV. B
–5–
Page 6
AD9762
DEFINITIONS OF SPECIFICATIONS Linearity Error (Also Called Integral Nonlinearity or INL)
Linearity error is defined as the maximum deviation of the actual analog output from the ideal output, determined by a straight line drawn from zero to full scale.
Differential Nonlinearity (or DNL)
DNL is the measure of the variation in analog value, normalized to full scale, associated with a 1 LSB change in digital input code.
Monotonicity
A D/A converter is monotonic if the output either increases or remains constant as the digital input increases.
Offset Error
The deviation of the output current from the ideal of zero is called offset error. For I inputs are all 0s. For I
, 0 mA output is expected when the
OUTA
, 0 mA output is expected when all
OUTB
inputs are set to 1s.
Gain Error
The difference between the actual and ideal output span. The actual span is determined by the output when all inputs are set to 1s minus the output when all inputs are set to 0s.
Output Compliance Range
The range of allowable voltage at the output of a current-output DAC. Operation beyond the maximum compliance limits may cause either output stage saturation or breakdown resulting in nonlinear performance.
Temperature Drift
Temperature drift is specified as the maximum change from the ambient (+25°C) value to the value at either T
MIN
or T
MAX
. For offset and gain drift, the drift is reported in ppm of full-scale range (FSR) per degree C. For reference drift, the drift is reported in ppm per degree C.
Power Supply Rejection
The maximum change in the full-scale output as the supplies are varied from nominal to minimum and maximum specified voltages.
Settling Time
The time required for the output to reach and remain within a specified error band about its final value, measured from the start of the output transition.
Glitch Impulse
Asymmetrical switching times in a DAC give rise to undesired output transients that are quantified by a glitch impulse. It is specified as the net area of the glitch in pV-s.
Spurious-Free Dynamic Range
The difference, in dB, between the rms amplitude of the output signal and the peak spurious signal over the specified bandwidth.
Total Harmonic Distortion
THD is the ratio of the rms sum of the first six harmonic components to the rms value of the measured output signal. It is expressed as a percentage or in decibels (dB).
Multitone Power Ratio
The spurious-free dynamic range for an output containing mul­tiple carrier tones of equal amplitude. It is measured as the difference between the rms amplitude of a carrier tone to the peak spurious signal in the region of a removed tone.
DVDD
DCOM
R
SET
2k
RETIMED
CLOCK
OUTPUT*
LECROY 9210
PULSE GENERATOR
0.1␮F
50
+5V
+5V
0.1␮F
+1.20V REF
REFIO
FS ADJ
DVDD
DCOM
CLOCK
SLEEP
REFLO
SEGMENTED SWITCHES
FOR DB11–DB3
CLOCK
OUTPUT
50pF
COMP1
LATCHES
DIGITAL
TEKTRONIX
AWG-2021
AVDD ACOM
PMOS
CURRENT SOURCE
ARRAY
LSB
SWITCHES
DATA
AD9762
COMP2
IOUTA
IOUTB
Figure 2. Basic AC Characterization Test Set-Up
50
0.1␮F
MINI-CIRCUITS
100
50
20pF
20pF
* AWG2021 CLOCK RETIMED SUCH THAT DIGITAL DATA TRANSITIONS ON FALLING EDGE OF 50% DUTY CYCLE CLOCK.
T1-1T
TO HP3589A SPECTRUM/ NETWORK ANALYZER 50 INPUT
–6–
REV. B
Page 7
Typical AC Characterization Curves @ +5 V Supplies
(AVDD = +5 V, DVDD = +5 V, I
= 20 mA, 50 ⍀ Doubly Terminated Load, Differential Output, TA = +25ⴗC, SFDR up to Nyquist, unless otherwise noted)
OUTFS
AD9762
90
80
5MSPS
50MSPS
70
SFDR – dBc
60
50
0.1 100
Figure 3. SFDR vs. f
85
80
75
70
65
SFDR – dBc
0dBFS
60
55
50
0.00 5.00 25.0010.00 15.00 20.00
Figure 6. SFDR vs. f
25MSPS
125MSPS
110
FREQUENCY – MHz
@ 0 dBFS
OUT
–6dBFS
–12dBFS
FREQUENCY – MHz
@ 50 MSPS
OUT
100MSPS
85
80
75
70
65
SFDR – dBc
60
55
50
0.00 2.50
Figure 4. SFDR vs. f
85
80
75
70
65
SFDR – dBc
60
55
50
0.00 10.00 50.00
Figure 7. SFDR vs. f
–6dBFS
0dBFS
–12dBFS
0.50 1.00 1.50 2.00 FREQUENCY – MHz
@ 5 MSPS
OUT
–6dBFS
0dBFS
20.00 30.00 40.00
FREQUENCY – MHz
@100 MSPS
OUT
–12dBFS
85
–6dBFS
80
75
70
65
SFDR – dBc
60
55
50
0.00 2.00 12.004.00 6.00 8.00 10.00
Figure 5. SFDR vs. f
85
80
75
70
65
SFDR – dBc
60
0dBFS
55
50
0.00 10.00 60.0020.00 30.00 40.00 50.00
Figure 8. SFDR vs. f
–12dBFS
0dBFS
FREQUENCY – MHz
–6dBFS
FREQUENCY – MHz
OUT
–12dBFS
OUT
@ 25 MSPS
@ 125 MSPS
85
75
@ 25MSPS
65
SFDR – dBc
55
45
–30 –25 0
455kHz
@ 5MSPS
2.27MHz
–20 –15 –10 –5
A
9.1MHz @ 100MSPS
– dBFS
OUT
4.55MHz @ 50MSPS
11.37MHz
@ 125MSPS
Figure 9. Single-Tone SFDR vs. A @ f
OUT
= f
CLOCK
/11
REV. B
OUT
85
75
@ 25MSPS
65
SFDR – dBc
55
45
–30 –25 0
1MHz
@ 5MSPS
5.0MHz
25MHz
@ 125MSPS
–20 –15 –10 –5
A
OUT
10MHz
@ 50MSPS
@ 100MSPS
– dBFS
20MHz
Figure 10. Single-Tone SFDR vs.
@ f
A
OUT
OUT
= f
CLOCK
/5
–7–
0.675/0.725MHz
80
70
60
SFDR – dBc
50
40
–30 –25 0
@ 5MSPS
3.38/3.63MHz @ 25MSPS
6.75/7.25MHz @ 50MSPS
13.5/14.5MHz @ 100MSPS
16.9/18.1MHz @ 125MSPS
–20 –15 –10 –5
A
– dBFS
OUT
Figure 11. Dual-Tone SFDR vs. A @ f
OUT
= f
CLOCK
/7
OUT
Page 8
AD9762
70
75
2ND
–80
dBc
85
90
95
0.25
ERROR LSB
0.50
0.75
1.00
1.25
HARMONIC
3RD
HARMONIC
4TH HARMONIC
0 20 140
Figure 12. THD vs. f f
OUT
1.25
1.00
0.75
0.50
0.25
0
40 60 80 100 120
FREQUENCY – MSPS
= 2 MHz
0
1000 2000 3000
CLOCK
CODE
Figure 15. Typical INL
@
4000
80
75
70
65
60
55
50
SFDR – dBc
45
40
35
30
28 2014
4 6 10 12 16 18
I
OUTFS
– mA
Figure 13. SFDR vs. f @ 100 MSPS, 0 dBFS
1
0.8
0.6
0.4
0.2
ERROR – LSB
0
0.2
0.4
0
1000 2000 3000
CODE
Figure 16. Typical DNL
2.5MHz
10MHz
22.2MHz
40MHz
and I
OUT
OUTFS
4000
75
IDIFF @ 0dBFS
70
65
IOUTA @ 0dBFS
60
SFDR – dBc
55
IOUTA @ –6dBFS
50
45
1 10 100
OUTPUT FREQUENCY – MHz
IDIFF @ –6dBFS
Figure 14. Differential vs. Single­Ended SFDR vs. f
80
75
70
65
SFDR – dBc
60
55
50
2.5MHz
10MHz
40MHz
–40 –20 80
TEMPERATURE – C
@ 100 MSPS
OUT
60
40200
Figure 17. SFDR vs. Temperature @ 100 MSPS, 0 dBFS
0
10dB – Div
–100
START: 0.3 MHz STOP: 50.0 MHz
f
= 100 MSPS
CLOCK
= 2.41MHz
f
OUT
SFDR = 72dBc AMPLITUDE = 0dBFS
Figure 18. Single-Tone SFDR
0
f
= 100 MSPS
CLOCK
= 13.5MHz
f
OUT1
= 14.5MHz
f
OUT2
SFDR = 62dBc AMPLITUDE = 0dBFS
10dB – Div
–100
START: 0.3 MHz STOP: 50.0 MHz
Figure 19. Dual-Tone SFDR
–10
10dB – Div
–110
START: 0.3 MHz STOP: 25.0 MHz
f
= 50 MSPS
CLOCK
= 6.25MHz
f
OUT1
= 6.75MHz
f
OUT2
= 7.25MHz
f
OUT3
= 7.75MHz
f
OUT4
SFDR = 71dBc AMPLITUDE = 0dBFS
Figure 20. Four-Tone SFDR
–8–
REV. B
Page 9
Typical AC Characterization Curves @ +3 V Supplies
(AVDD = +3 V, DVDD = +3 V, I
= 20 mA, 50 Doubly Terminated Load, Differential Output, TA = +25C, SFDR up to Nyquist, unless otherwise noted)
OUTFS
AD9762
90
80
5MSPS
25MSPS
50MSPS
70
SFDR – dBc
60
125MSPS
50
0.1 100
110
FREQUENCY – MHz
Figure 21. SFDR vs. f
85
80
75
–6dBFS
70
65
SFDR – dBc
0dBFS
60
55
50
05 25
10 15 20
FREQUENCY – MHz
Figure 24. SFDR vs. f
100MSPS
@ 0 dBFS
OUT
12dBFS
@ 50 MSPS
OUT
85
80
75
–12dBFS
70
65
SFDR – dBc
60
55
50
0.00 2.500.50 1.00 1.50 2.00
Figure 22. SFDR vs. f
85
80
75
70
65
SFDR – dBc
60
0dBFS
55
50
010 50
Figure 25. SFDR vs. f
0dBFS
FREQUENCY – MHz
OUT
6dBFS
12dBFS
20 30 40
FREQUENCY – MHz
OUT
–6dBFS
@ 5 MSPS
@ 100 MSPS
85
80
75
70
65
SFDR – dBc
60
55
50
02 1246 8 10
0dBFS
FREQUENCY – MHz
Figure 23. SFDR vs. f
85
80
75
0dBFS
70
65
SFDR – dBc
60
55
50
010 6020 30 40 50
FREQUENCY – MHz
Figure 26. SFDR vs. f
12dBFS
6dBFS
OUT
12dBFS
6dBFS
OUT
@ 25 MSPS
@ 125 MSPS
90
80
2.27MHz
@ 25MSPS
70
60
SFDR – dBc
50
40
–30 –25 0
455kHz
@ 5MSPS
–20 –15 –10 –5
A
– dBFS
OUT
@ 50MSPS
9.1MHz
@ 100MSPS
@ 125MSPS
4.55MHz
11.37MHz
Figure 27. Single-Tone SFDR vs. A @ f
OUT
= f
CLOCK
/11
REV. B
OUT
90
1MHz
80
70
60
SFDR – dBc
50
40
–30 –25 0
@ 5MSPS
5.0MHz
@ 25MSPS
@ 50MSPS
25MHz @ 125MSPS
–20 –15 –10 –5
A
OUT
10MHz
– dBFS
20MHz @ 100MSPS
Figure 28. Single-Tone SFDR vs. A
@ f
OUT
OUT
= f
CLOCK
/5
–9–
90
0.675/0.725MHz
80
3.38/3.63MHz
70
60
SFDR – dBc
50
40
–30 –25 0
@ 5MSPS
@ 25MSPS
13.5/14.5MHz @ 100MSPS
–20 –15 –10 –5
A
OUT
6.75/7.25MHz @ 50MSPS
– dBFS
16.9/18.1MHz @ 125MSPS
Figure 29. Dual-Tone SFDR vs. A @ f
OUT
= f
CLOCK
/7
OUT
Page 10
AD9762
70
75
80
dBc
85
90
95
0 20 140
Figure 30. THD vs. f
2ND
HARMONIC
4TH HARMONIC
40 60 80 100 120
FREQUENCY – MSPS
3RD HARMONIC
CLOCK
2 MHz
1.25
1.00
0.75
0.50
0.25
0
–0.25
ERROR – LSB
0.50
0.75
1.00
1.25
0
1000 2000 3000
CODE
Figure 33. Typical INL
@ f
OUT
=
4000
80
75
70
65
60
55
50
SFDR – dBc
45
40
35
30
24 20
6 8 10 12 16 18
I
Figure 31. SFDR vs. f
OUTFS
– mA
2.5MHz
10MHz
22.2MHz
40MHz
14
and I
OUT
@ 100 MSPS, 0 dBFS
1
0.8
0.6
0.4
0.2
ERROR – LSB
0
0.2
0.4
0
1000 2000 3000
CODE
Figure 34. Typical DNL
OUTFS
4000
75
70
65
60
SFDR – dBc
55
50
45
1 10 100
IOUTA @
–6dBFS
OUTPUT FREQUENCY – MHz
IOUTA @
0dBFS
IDIFF @ –6dBFS
IDIFF @
0dBFS
Figure 32. Differential vs. Single Ended SFDR vs. f
80
75
70
65
10MHz
SFDR – dBc
60
55
50
28.6MHz
–40 –20 8060
TEMPERATURE – C
@ 100 MSPS
OUT
2.5MHz
40200
Figure 35. SFDR vs. Temperature @ 100 MSPS, 0 dBFS
0
f
= 100 MSPS
CLOCK
= 2.41MHz
f
OUT
SFDR = 72dBc AMPLITUDE = 0dBFS
10dB – Div
–100
START: 0.3 MHz STOP: 50.0 MHz
Figure 36. Single-Tone SFDR
0
f
= 100 MSPS
CLOCK
= 13.5MHz
f
OUT1
= 14.5MHz
f
OUT2
SFDR = 59.0dBc AMPLITUDE = 0dBFS
10dB – Div
–100
START: 0.3 MHz STOP: 50.0 MHz
Figure 37. Dual-Tone SFDR
–10
f
= 50 MSPS
CLOCK
= 6.25MHz
f
OUT1
= 6.75MHz
f
OUT2
= 7.25MHz
f
OUT3
f
= 7.75MHz
OUT4
SFDR = 71dBc AMPLITUDE = 0dBFS
10dB – Div
–110
START: 0.3 MHz STOP: 25.0 MHz
Figure 38. Four-Tone SFDR
–10–
REV. B
Page 11
AD9762
)

FUNCTIONAL DESCRIPTION

Figure 39 shows a simplified block diagram of the AD9762. The AD9762 consists of a large PMOS current source array that is capable of providing up to 20 mA of total current. The array is divided into 31 equal currents that make up the 5 most significant bits (MSBs). The next 4 bits or middle bits consist of 15 equal current sources whose value is 1/16th of an MSB current source. The remaining LSBs are binary weighted fractions of the middle-bits current sources. Implementing the middle and lower bits with current sources, instead of an R-2R ladder, enhances its dynamic performance for multitone or low amplitude signals and helps maintain the DAC’s high output impedance (i.e., >100 k).
All of these current sources are switched to one or the other of the two output nodes (i.e., I
OUTA
or I
) via PMOS differen-
OUTB
tial current switches. The switches are based on a new archi­tecture that drastically improves distortion performance. This new switch architecture reduces various timing errors and provides matching complementary drive signals to the inputs of the differential current switches.
The analog and digital sections of the AD9762 have separate power supply inputs (i.e., AVDD and DVDD) that can operate independently over a 2.7 volt to 5.5 volt range. The digital section, which is capable of operating up to a 125 MSPS clock rate, consists of edge-triggered latches and segment decoding logic circuitry. The analog section includes the PMOS current sources, the associated differential switches, a 1.20 V bandgap voltage reference and a reference control amplifier.
The full-scale output current is regulated by the reference control amplifier and can be set from 2 mA to 20 mA via an external resistor, R
. The external resistor, in combination
SET
with both the reference control amplifier and voltage refer­ence V
, sets the reference current I
REFIO
, which is mirrored
REF
over to the segmented current sources with the proper scaling factor. The full-scale current, I
.
of I
REF
, is thirty-two times the value
OUTFS

DAC TRANSFER FUNCTION

The AD9762 provides complementary current outputs, I and I I
OUTFS
I
OUTB
current output appearing at I both the input code and I
. I
OUTB
will provide a near full-scale current output,
OUTA
, when all bits are high (i.e., DAC CODE = 4095) while
, the complementary output, provides no current. The
and I
OUTA
and can be expressed as:
OUTFS
is a function of
OUTB
OUTA
= (DAC CODE/4096) × I
I
OUTA
I
= (4095 – DAC CODE)/4096 × I
OUTB
OUTFS
OUTFS
(1)
(2)
where DAC CODE = 0 to 4095 (i.e., Decimal Representation).
As mentioned previously, I current I V
REFIO
I
where I
, which is nominally set by a reference voltage
REF
and external resistor R
= 32 × I
OUTFS
REF
= V
REF
REFIO/RSET
is a function of the reference
OUTFS
. It can be expressed as:
SET
(3)
(4)
The two current outputs will typically drive a resistive load directly or via a transformer. If dc coupling is required, I and I loads, R R
LOAD
I
OUTA
should be directly connected to matching resistive
OUTB
, which are tied to analog common, ACOM. Note,
LOAD
may represent the equivalent load resistance seen by
or I
as would be the case in a doubly terminated
OUTB
OUTA
50 or 75 cable. The single-ended voltage output appearing at the I
V
OUTA
V
OUTB
Note the full-scale value of V
OUTA
= I
= I
and I
OUTA
OUTB
nodes is simply :
OUTB
× R
LOAD
× R
LOAD
OUTA
and V
should not exceed
OUTB
(5)
(6)
the specified output compliance range to maintain specified distortion and linearity performance.
The differential voltage, V I
is:
OUTB
V
DIFF
= (I
OUTA
– I
Substituting the values of I
, appearing across I
DIFF
) × R
OUTB
OUTA
LOAD
, I
OUTB
, and I
REF
OUTA
; V
DIFF
and
(7)
can be
expressed as:
V
= {(2 DAC CODE – 4095)/4096} ×
DIFF
(32 R
LOAD/RSET
) × V
REFIO
(8)
These last two equations highlight some of the advantages of operating the AD9762 differentially. First, the differential operation will help cancel common-mode error sources associated with I
OUTA
and I
such as noise, distortion and dc offsets.
OUTB
Second, the differential code dependent current and subsequent voltage, V output (i.e., V
, is twice the value of the single-ended voltage
DIFF
OUTA
or V
), thus providing twice the signal
OUTB
power to the load.
Note, the gain drift temperature performance for a single-ended (V
OUTA
and V
) or differential output (V
OUTB
) of the AD9762
DIFF
can be enhanced by selecting temperature tracking resistors for R
LOAD
and R
due to their ratiometric relationship as shown
SET
in Equation 8.
REV. B
0.1␮F
V
REFIO
R
2k
CLOCK
SET
I
REF
+5V
+5V
0.1␮F
+1.20V REF
REFIO
FS ADJ
DVDD
DCOM
CLOCK
SLEEP
REFLO
SEGMENTED SWITCHES
FOR DB11–DB3
DIGITAL DATA INPUTS (DB11–DB0
COMP1
50pF
LATCHES
PMOS
CURRENT SOURCE
ARRAY
Figure 39. Functional Block Diagram
–11–
AVDD ACOM
AD9762
LSB
SWITCHES
COMP2
IOUTA
IOUTB
0.1␮F
I
OUTB
I
OUTA
V
DIFF
V
R 50
= V
OUTB
LOAD
OUTA
– V
V
R 50
OUTB
OUTA
LOAD
Page 12
AD9762

REFERENCE OPERATION

The AD9762 contains an internal 1.20 V bandgap reference that can be easily disabled and overridden by an external refer­ence. REFIO serves as either an input or output depending on whether the internal or an external reference is selected. If REFLO is tied to ACOM, as shown in Figure 40, the internal reference is activated and REFIO provides a 1.20 V output. In this case, the internal reference must be compensated externally with a ceramic chip capacitor of 0.1 µF or greater from REFIO to REFLO. Also, REFIO should be buffered with an external amplifier having an input bias current less than 100 nA if any additional loading is required.
+5V
50pF
0.1␮F
COMP1
CURRENT
AVDD
SOURCE
ARRAY
ADDITIONAL
LOAD
OPTIONAL
EXTERNAL
REF BUFFER
0.1␮F
2k
REFLO
+1.2V REF
REFIO
FS ADJ
AD9762
Figure 40. Internal Reference Configuration
The internal reference can be disabled by connecting REFLO to AVDD. In this case, an external reference may then be applied to REFIO as shown in Figure 41. The external reference may provide either a fixed reference voltage to enhance accuracy and drift performance or a varying reference voltage for gain control. Note that the 0.1 µF compensation capacitor is not required since the internal reference is disabled, and the high input impedance (i.e., 1 M) of REFIO minimizes any loading of the external reference.
AVDD
0.1␮F
AVDD
EXTERNAL
REF
REFLO
+1.2V REF
V
REFIO
R
I
SET
REF
V
REFIO/RSET
REFIO
FS ADJ
=
AD9762
50pF

REFERENCE CONTROL AMPLIFIER

COMP1
CURRENT
AVDD
SOURCE
ARRAY
Figure 41. External Reference Configuration
REFERENCE CONTROL AMPLIFIER
The AD9762 also contains an internal control amplifier that is used to regulate the DAC’s full-scale output current, I
OUTFS
. The control amplifier is configured as a V-I converter as shown in Figure 41, such that its current output, I the ratio of the V in Equation 4. I
and an external resistor, R
REFIO
is copied over to the segmented current
REF
sources with the proper scaling factor to set I
, is determined by
REF
SET
OUTFS
, as stated
as stated in
Equation 3.
The control amplifier allows a wide (10:1) adjustment span of
over a 2 mA to 20 mA range by setting IREF between
I
OUTFS
62.5 µA and 625 µA. The wide adjustment span of I
OUTFS
provides several application benefits. The first benefit relates directly to the power dissipation of the AD9762, which is proportional to I
(refer to the Power Dissipation section).
OUTFS
The second benefit relates to the 20 dB adjustment, which is useful for system gain control purposes.
The small signal bandwidth of the reference control amplifier is approximately 1.4 MHz and can be reduced by connecting an external capacitor between COMP1 and AVDD. The output of the control amplifier, COMP1, is internally compensated via a 50 pF capacitor that limits the control amplifier small-signal bandwidth and reduces its output impedance. Any additional external capacitance further limits the bandwidth and acts as a filter to reduce the noise contribution from the reference ampli­fier. Figure 42 shows the relationship between the external capacitor and the small signal –3 dB bandwidth of the
1000
10
BANDWIDTH – kHz
0
0.1 1000
1 10 100
COMP1 CAPACITOR – nF
Figure 42. External COMP1 Capacitor vs. –3 dB Bandwidth
reference amplifier. Since the –3 dB bandwidth corresponds to the dominant pole, and hence the time constant, the settling time of the control amplifier to a stepped reference input response can be approximated.
The optimum distortion performance for any reconstructed waveform is obtained with a 0.1 µF external capacitor installed. Thus, if I
is fixed for an application, a 0.1 µF ceramic chip
REF
capacitor is recommended. Also, since the control amplifier is optimized for low power operation, multiplying applications requiring large signal swings should consider using an external control amplifier to enhance the application’s overall large signal multiplying bandwidth and/or distortion performance.
There are two methods in which I R
. The first method is suitable for a single-supply system in
SET
can be varied for a fixed
REF
which the internal reference is disabled, and the common-mode voltage of REFIO is varied over its compliance range of 1.25 V to 0.10 V. REFIO can be driven by a single-supply amplifier or DAC, thus allowing I
to be varied for a fixed R
REF
. Since the
SET
input impedance of REFIO is approximately 1 M, a simple, low cost R-2R ladder DAC configured in the voltage mode topology may be used to control the gain. This circuit is shown in Figure 43 using the AD7524 and an external 1.2 V reference, the AD1580.
–12–
REV. B
Page 13
AVDD
AD9762
AVDD
1.2V
AD1580
R
OUT1
OUT2
AGND
FB
AD7524
V
DD
V
DB7–DB0
REF
0.1V TO 1.2V
R
SET
I V
Figure 43. Single-Supply Gain Control Circuit
The second method may be used in a dual-supply system in which the common-mode voltage of REFIO is fixed and I varied by an external voltage, V
, applied to R
GC
via an ampli-
SET
REF
is
fier. An example of this method is shown in Figure 44 in which the internal reference is used to set the common-mode voltage of the control amplifier to 1.20 V. The external voltage, V
GC
, is referenced to ACOM and should not exceed 1.2 V. The value of R
SET
is such that I
REFMAX
and I
do not exceed 62.5 µA
REFMIN
and 625 µA, respectively. The associated equations in Figure 44 can be used to determine the value of R
BANDLIMITING
REFLO
+1.2V REF
REFIO
I
REF
I
= (1.2–VGC)/R
REF
WITH V
FS ADJ
AD9762
< V
GC
SET
REFIO
1F
V
R
SET
GC
.
SET
OPTIONAL
CAPACITOR
COMP1
50pF
AND 62.5␮A ⱕ I
AVDD
AVDD
CURRENT
SOURCE
ARRAY
625A
REF
Figure 44. Dual-Supply Gain Control Circuit
In some applications, the user may elect to use an external con­trol amplifier to enhance the multiplying bandwidth, distortion performance, and/or settling time. External amplifiers capable of driving a 50 pF load such as the AD817 are suitable for this purpose. It is configured in such a way that it is in parallel with the weaker internal reference amplifier as shown in Figure 45. In this case, the external amplifier simply overdrives the weaker reference control amplifier. Also, since the internal control amplifier has a limited current output, it will sustain no damage if overdriven.
EXTERNAL
CONTROL AMPLIFIER
V
REF
INPUT
R
SET
+1.2V REF
REFIO
FS ADJ
AD9762
REFLO
50pF
COMP1
CURRENT
SOURCE
ARRAY
AVDD
AVDD
Figure 45. Configuring an External Reference Control Amplifier
OPTIONAL
BANDLIMITING
CAPACITOR
=
REF
REF/RSET
REFLO
+1.2V REF
REFIO
FS ADJ
AD9762
50pF
COMP1
CURRENT
AVDD
SOURCE
ARRAY

ANALOG OUTPUTS

The AD9762 produces two complementary current outputs, I
and I
OUTA
differential operation. I complementary single-ended voltage outputs, V via a load resistor, R
, which may be configured for single-ended or
OUTB
and I
OUTA
, as described in the DAC Transfer
LOAD
can be converted into
OUTB
OUTA
and V
OUTB
Function section by Equations 5 through 8. The differential voltage, V
, existing between V
DIFF
OUTA
and V
can also be
OUTB
converted to a single-ended voltage via a transformer or differ­ential amplifier configuration. The ac performance of the AD9762 is optimum and specified using a differential trans­former coupled output in which the voltage swing at I I
is limited to ±0.5 V. If a single-ended unipolar output is
OUTB
desirable, I
should be selected.
OUTA
OUTA
and
The distortion and noise performance of the AD9762 can be enhanced when the AD9762 is configured for differential opera­tion. The common-mode error sources of both I
OUTA
and I
OUTB
can be significantly reduced by the common-mode rejection of a transformer or differential amplifier. These common-mode error sources include even-order distortion products and noise. The enhancement in distortion performance becomes more significant as the frequency content of the reconstructed wave­form increases. This is due to the first order cancellation of various dynamic common-mode distortion mechanisms, digital feedthrough and noise.
Performing a differential-to-single-ended conversion via a transformer also provides the ability to deliver twice the recon­structed signal power to the load (i.e., assuming no source termination). Since the output currents of I
OUTA
and I
OUTB
are complementary, they become additive when processed differen­tially. A properly selected transformer will allow the AD9762 to provide the required power and voltage levels to different loads. Refer to Applying the AD9762 section for examples of various output configurations.
The output impedance of I
OUTA
and I
is determined by the
OUTB
equivalent parallel combination of the PMOS switches associ­ated with the current sources and is typically 100 k in parallel with 5 pF. It is also slightly dependent on the output voltage
OUTA
and V
(i.e., V As a result, maintaining I
) due to the nature of a PMOS device.
OUTB
OUTA
and/or I
at a virtual ground
OUTB
via an I-V op amp configuration will result in the optimum dc linearity. Note, the INL/DNL specifications for the AD9762 are measured with I
maintained at a virtual ground via an
OUTA
op amp.
,
REV. B
–13–
Page 14
AD9762
I
and I
OUTA
compliance range that must be adhered to in order to achieve optimum performance. The negative output compliance range of –1.0 V is set by the breakdown limits of the CMOS process. Operation beyond this maximum limit may result in a break­down of the output stage and affect the reliability of the AD9762.
The positive output compliance range is slightly dependent on the full-scale output current, I from its nominal 1.25 V for an I I
= 2 mA. The optimum distortion performance for a
OUTFS
single-ended or differential output is achieved when the maximum full-scale signal at I Applications requiring the AD9762’s output (i.e., V or V R
) to extend its output compliance range should size
OUTB
accordingly. Operation beyond this compliance range
LOAD
will adversely affect the AD9762’s linearity performance and subsequently degrade its distortion performance.

DIGITAL INPUTS

The AD9762’s digital input consists of 12 data input pins and a clock input pin. The 12-bit parallel data inputs follow standard positive binary coding where DB11 is the most significant bit (MSB) and DB0 is the least significant bit (LSB). I a full-scale output current when all data bits are at Logic 1. I
produces a complementary output with the full-scale current
OUTB
split between the two outputs as a function of the input code.
The digital interface is implemented using an edge-triggered master slave latch. The DAC output is updated following the rising edge of the clock as shown in Figure 1 and is designed to support a clock rate as high as 125 MSPS. The clock can be operated at any duty cycle that meets the specified latch pulsewidth. The set-up and hold times can also be varied within the clock cycle as long as the specified minimum times are met; although the location of these transition edges may affect digital feedthrough and distortion performance. Best performance is
typically achieved when the input data transitions on the falling edge of a 50% duty cycle clock.
The digital inputs are CMOS compatible with logic thresholds, V
THRESHOLD
(DVDD) or
The internal digital circuitry of the AD9762 is capable of operating over a digital supply range of 2.7 V to 5.5 V. As a result, the digital inputs can also accommodate TTL levels when DVDD is set to accommodate the maximum high level voltage of the TTL drivers V
OH(MAX)
proper compatibility with most TTL logic families. Figure 46 shows the equivalent digital input circuit for the data and clock inputs. The sleep mode input is similar with the exception that it contains an active pull-down circuit, thus ensuring that the AD9762 remains enabled if this input is left disconnected.
also have a negative and positive voltage
OUTB
. It degrades slightly
OUTFS
= 20 mA to 1.00 V for an
OUTFS
OUTA
and I
does not exceed 0.5 V.
OUTB
OUTA
and/
OUTA
produces
set to approximately half the digital positive supply
V
THRESHOLD
= DVDD/2 (±20%)
. A DVDD of 3 V to 3.3 V will typically ensure
DVDD
DIGITAL
INPUT
Figure 46. Equivalent Digital Input
–14–
Since the AD9762 is capable of being updated up to 125 MSPS, the quality of the clock and data input signals are important in achieving the optimum performance. The drivers of the digital data interface circuitry should be specified to meet the minimum set-up and hold times of the AD9762 as well as its required min/max input logic level thresholds. Typically, the selection of the slowest logic family that satisfies the above conditions will result in the lowest data feedthrough and noise.
Digital signal paths should be kept short and run lengths matched to avoid propagation delay mismatch. The insertion of a low value resistor network (i.e., 20 to 100 ) between the AD9762 digital inputs and driver outputs may be helpful in reducing any overshooting and ringing at the digital inputs that contribute to data feedthrough. For longer run lengths and high data update rates, strip line techniques with proper termination resistors should be considered to maintain “clean” digital inputs. Also, operating the AD9762 with reduced logic swings and a corresponding digital supply (DVDD) will also reduce data feedthrough.
The external clock driver circuitry should provide the AD9762 with a low jitter clock input meeting the min/max logic levels while providing fast edges. Fast clock edges will help minimize any jitter that will manifest itself as phase noise on a recon­structed waveform. Thus, the clock input should be driven by the fastest logic family suitable for the application.
Note, the clock input could also be driven via a sine wave, which is centered around the digital threshold (i.e., DVDD/2), and meets the min/max logic threshold. This will typically result in a slight degradation in the phase noise, which becomes more noticeable at higher sampling rates and output frequencies. Also, at higher sampling rates, the 20% tolerance of the digital logic threshold should be considered since it will affect the effective clock duty cycle and subsequently cut into the required data set-up and hold times.

SLEEP MODE OPERATION

The AD9762 has a power-down function which turns off the output current and reduces the supply current to less than
8.5 mA over the specified supply range of 2.7 V to 5.5 V and temperature range. This mode can be activated by applying a logic level “1” to the SLEEP pin. This digital input also contains an active pull-down circuit that ensures the AD9762 remains enabled if this input is left disconnected. The SLEEP input with active pull-down requires <40 µA of drive current.
The power-up and power-down characteristics of the AD9762 are dependent upon the value of the compensation capacitor connected to COMP1. With a nominal value of 0.1 µF, the AD9762 takes less than 5 µs to power down and approximately
3.25 ms to power back up. Note, the SLEEP MODE should not be used when the external control amplifier is used as shown in Figure 45.

POWER DISSIPATION

The power dissipation, PD, of the AD9762 is dependent on several factors which include: (1) AVDD and DVDD, the power supply voltages; (2) I f
, the update rate; (4) and the reconstructed digital input
CLOCK
, the full-scale current output; (3)
OUTFS
waveform. The power dissipation is directly proportional to the analog supply current, I I
is directly proportional to I
AVDD
and is insensitive to f
CLOCK
, and the digital supply current, I
AVDD
as shown in Figure 47
OUTFS
.
DVDD
.
REV. B
Page 15
AD9762
30
25
20
– mA
15
AVDD
I
10
5
0
2204 6 8 10 12141618
Figure 47. I
Conversely, I form, f
CLOCK
show I
DVDD
(f
OUT/fCLOCK
is dependent on both the digital input wave-
DVDD
, and digital supply DVDD. Figures 48 and 49
as a function of full-scale sine wave output ratios
) for various update rates with DVDD = 5 V and
DVDD = 3 V, respectively. Note, how I
I
OUTFS
AVDD
– mA
vs. I
OUTFS
is reduced by more
DVDD
than a factor of 2 when DVDD is reduced from 5 V to 3 V.
18
16
14
12
10
– mA
8
DVDD
I
6
4
2
0
0.01 10.1
Figure 48. I
8
6
RATIO (f
vs. Ratio @ DVDD = 5 V
DVDD
OUT/fCLK
125MSPS
100MSPS
50MSPS
25MSPS
5MSPS
)
125MSPS
100MSPS

APPLYING THE AD9762

OUTPUT CONFIGURATIONS

The following sections illustrate some typical output configura­tions for the AD9762. Unless otherwise noted, it is assumed that I
is set to a nominal 20 mA. For applications requir-
OUTFS
ing the optimum dynamic performance, a differential output configuration is suggested. A differential output configuration may consist of either an RF transformer or a differential op amp configuration. The transformer configuration provides the optimum high frequency performance and is recommended for any application allowing for ac coupling. The differential op amp configuration is suitable for applications requiring dc coupling, a bipolar output, signal gain and/or level shifting.
A single-ended output is suitable for applications requiring a unipolar voltage output. A positive unipolar output voltage will result if I sized load resistor, R
OUTA
and/or I
LOAD
is connected to an appropriately
OUTB
, referred to ACOM. This configura­tion may be more suitable for a single-supply system requiring a dc coupled, ground referred output voltage. Alternatively, an amplifier could be configured as an I-V converter thus converting I
or I
OUTA
tion provides the best dc linearity since I maintained at a virtual ground. Note, I better performance than I
into a negative unipolar voltage. This configura-
OUTB
OUTB
.
OUTA
or I
OUTA
OUTB
provides slightly
is

DIFFERENTIAL COUPLING USING A TRANSFORMER

An RF transformer can be used to perform a differential-to­single-ended signal conversion as shown in Figure 50. A differentially coupled transformer output provides the optimum distortion performance for output signals whose spectral content lies within the transformer’s passband. An RF transformer such as the Mini-Circuits T1-1T provides excellent rejection of common-mode distortion (i.e., even-order harmonics) and noise over a wide frequency range. It also provides electrical isolation and the ability to deliver twice the power to the load. Trans­formers with different impedance ratios may also be used for impedance matching purposes. Note that the transformer provides ac coupling only.
MINI-CIRCUITS
IOUTA
AD9762
IOUTB
22
21
T1-1T
OPTIONAL R
DIFF
R
LOAD
REV. B
– mA
4
DVDD
I
2
0
0.01 10.1
Figure 49. I
RATIO (f
vs. Ratio @ DVDD = 3 V
DVDD
OUT/fCLK
Figure 50. Differential Output Using a Transformer
The center tap on the primary side of the transformer must be
50MSPS
25MSPS
connected to ACOM to provide the necessary dc current path for both I ing at I
OUTA
OUTA
and I
and I
. The complementary voltages appear-
OUTB
OUTB
(i.e., V
OUTA
and V
) swing symmetri-
OUTB
cally around ACOM and should be maintained with the specified output compliance range of the AD9762. A differential resistor,
5MSPS
)
, may be inserted in applications in which the output of
R
DIFF
the transformer is connected to the load, R reconstruction filter or cable. R
is determined by the
DIFF
, via a passive
LOAD
transformer’s impedance ratio and provides the proper source termination which results in a low VSWR. Note that approxi­mately half the signal power will be dissipated across R
DIFF
.
15
Page 16
AD9762

DIFFERENTIAL USING AN OP AMP

An op amp can also be used to perform a differential to single­ended conversion as shown in Figure 51. The AD9762 is configured with two equal load resistors, R The differential voltage developed across I
LOAD
OUTA
, of 25 Ω.
and I
OUTB
is converted to a single-ended signal via the differential op amp configuration. An optional capacitor can be installed across I
OUTA
and I
forming a real pole in a low-pass filter. The
OUTB
addition of this capacitor also enhances the op amps distortion performance by preventing the DACs high slewing output from overloading the op amp’s input.
500
AD9762
IOUTA
IOUTB
22
21
C
OPT
225
225
2525
AD8047
500
Figure 51. DC Differential Coupling Using an Op Amp
The common-mode rejection of this configuration is typically determined by the resistor matching. In this circuit, the differ­ential op amp circuit using the AD8047 is configured to provide some additional signal gain. The op amp must operate off of a dual supply since its output is approximately ±1.0 V. A high speed amplifier capable of preserving the differential perfor­mance of the AD9762 while meeting other system level objec­tives (i.e., cost, power) should be selected. The op amps differential gain, its gain setting resistor values, and full-scale output swing capabilities should all be considered when opti­mizing this circuit.
The differential circuit shown in Figure 52 provides the neces­sary level-shifting required in a single supply system. In this case, AVDD which is the positive analog supply for both the AD9762 and the op amp is also used to level-shift the differ­ential output of the AD9762 to midsupply (i.e., AVDD/2). The AD8041 is a suitable op amp for this application.
500
AD9762
IOUTA
IOUTB
22
21
25
C
OPT
25
225
225
1k
AD8041
1k
AVDD
Figure 52. Single-Supply DC Differential Coupled Circuit

SINGLE-ENDED UNBUFFERED VOLTAGE OUTPUT

Figure 53 shows the AD9762 configured to provide a unipolar output range of approximately 0 V to +0.5 V for a doubly termi­nated 50 cable since the nominal full-scale current, I 20 mA flows through the equivalent R case, R I
OUTA
represents the equivalent load resistance seen by
LOAD
or I
. The unused output (I
OUTB
connected to ACOM directly or via a matching R values of I
OUTFS
and R
can be selected as long as the positive
LOAD
of 25 . In this
LOAD
or I
OUTA
OUTB
) can be
LOAD
, of
OUTFS
. Different
compliance range is adhered to. One additional consideration in
this mode is the integral nonlinearity (INL) as discussed in the Analog Output section of this data sheet. For optimum INL performance, the single-ended, buffered voltage output configu­ration is suggested.
I
AD9762
IOUTA
IOUTB
= 20mA
OUTFS
22
50
21
25
V
OUTA
= 0 TO +0.5V
50
Figure 53. 0 V to +0.5 V Unbuffered Voltage Output

SINGLE-ENDED, BUFFERED VOLTAGE OUTPUT CONFIGURATION

Figure 54 shows a buffered single-ended output configuration in which the op amp U1 performs an I-V conversion on the AD9762 output current. U1 maintains I
OUTA
(or I
OUTB
) at a virtual ground, thus minimizing the nonlinear output imped­ance effect on the DAC’s INL performance as discussed in the Analog Output section. Although this single-ended configu­ration typically provides the best dc linearity performance, its ac distortion performance at higher DAC update rates may be limited by U1’s slewing capabilities. U1 provides a negative unipolar output voltage and its full-scale output voltage is sim­ply the product of R
and I
FB
. The full-scale output should
OUTFS
be set within U1’s voltage output swing capabilities by scaling I
and/or RFB. An improvement in ac distortion perfor-
OUTFS
mance may result with a reduced I
since the signal current
OUTFS
U1 will be required to sink will be subsequently reduced.
C
OPT
R
FB
AD9762
IOUTA
IOUTB
I
= 10mA
OUTFS
22
21
200
200
U1
V
= I
OUTFS
R
FB
OUT
Figure 54. Unipolar Buffered Voltage Output

POWER AND GROUNDING CONSIDERATIONS

In systems seeking to simultaneously achieve high speed and high performance, the implementation and construction of the printed circuit board design is often as important as the circuit design. Proper RF techniques must be used in device selection; placement and routing; and supply bypassing and grounding. Figures 60–65 illustrate the recommended printed circuit board ground, power and signal plane layouts which are implemented on the AD9762 evaluation board.
Proper grounding and decoupling should be a primary objective in any high speed, high resolution system. The AD9762 features separate analog and digital supply and ground pins to optimize the management of analog and digital ground currents in a system. In general, AVDD, the analog supply, should be decoupled to ACOM, the analog common, as close to the chip as physi­cally possible. Similarly, DVDD, the digital supply, should be decoupled to DCOM as close as physically as possible.
–16–
REV. B
Page 17
AD9762
For those applications that require a single +5 V or +3 V supply for both the analog and digital supply, a clean analog supply may be generated using the circuit shown in Figure 55. The circuit consists of a differential LC filter with separate power supply and return lines. Lower noise can be attained using low ESR type electrolytic and tantalum capacitors.
FERRITE
BEADS
TTL/CMOS
LOGIC
CIRCUITS
+5V OR +3V
POWER SUPPLY
100F ELECT.
10-22␮F TANT.
0.1␮F CER.
AVDD
ACOM
Figure 55. Differential LC Filter for Single +5 V or +3 V Applications
Maintaining low noise on power supplies and ground is critical to obtaining optimum results from the AD9762. If properly implemented, ground planes can perform a host of functions on high speed circuit boards: bypassing, shielding, current trans­port, etc. In mixed signal design, the analog and digital portions of the board should be distinct from each other, with the analog ground plane confined to the areas covering the analog signal traces, and the digital ground plane confined to areas covering the digital interconnects.
All analog ground pins of the DAC, reference and other analog components should be tied directly to the analog ground plane. The two ground planes should be connected by a path 1/8 to 1/4 inch wide underneath or within 1/2 inch of the DAC to maintain optimum performance. Care should be taken to ensure that the ground plane is uninterrupted over crucial signal paths. On the digital side, this includes the digital input lines running to the DAC as well as any clock signals. On the analog side, this includes the DAC output signal, reference signal and the supply feeders.
The use of wide runs or planes in the routing of power lines is also recommended. This serves the dual role of providing a low series impedance power supply to the part, as well as providing some “free” capacitive decoupling to the appropriate ground plane. It is essential that care be taken in the layout of signal and power ground interconnects to avoid inducing extraneous voltage drops in the signal ground paths. It is recommended that all connections be short, direct and as physically close to the package as possible in order to minimize the sharing of conduc­tion paths between different currents. When runs exceed an inch in length, strip line techniques with proper termination resistor should be considered. The necessity and value of this resistor will be dependent upon the logic family used.
For a more detailed discussion of the implementation and construction of high speed, mixed signal printed circuit boards, refer to Analog Devices’ application notes AN-280 and AN-333.
APPLICATIONS Using the AD9762 for QAM Modulation
QAM is one of the most widely used digital modulation schemes in digital communication systems. This modulation technique can be found in both FDM as well as spreadspectrum (i.e., CDMA) based systems. A QAM signal is a carrier frequency which is both modulated in amplitude (i.e., AM modulation) and in phase (i.e., PM modulation). It can be generated by independently modulating two carriers of identical frequency but with a 90° phase difference. This results in an in-phase (I) carrier component and a quadrature (Q) carrier component at a 90° phase shift with respect to the I component. The I and Q components are then summed to provide a QAM signal at the specified carrier frequency.
A common and traditional implementation of a QAM modu­lator is shown in Figure 56. The modulation is performed in the analog domain in which two DACs are used to generate the baseband I and Q components, respectively. Each component is then typically applied to a Nyquist filter before being applied to a quadrature mixer. The matching Nyquist filters shape and limit each component’s spectral envelope while minimizing intersymbol interference. The DAC is typically updated at the QAM symbol rate or possibly a multiple of it if an interpolating filter precedes the DAC. The use of an interpolating filter typi­cally eases the implementation and complexity of the analog filter, which can be a significant contributor to mismatches in gain and phase between the two baseband channels. A quadra­ture mixer modulates the I and Q components with in-phase and quadrature phase carrier frequency and then sums the two outputs to provide the QAM signal.
12
AD9762
DSP
OR
ASIC
CARRIER
FREQUENCY
12
AD9762
NYQUIST
FILTERS
0
Σ
90
QUADRATURE
MODULATOR
TO MIXER
Figure 56. Typical Analog QAM Architecture
In this implementation, it is much more difficult to maintain proper gain and phase matching between the I and Q channels. The circuit implementation shown in Figure 57 helps improve upon the matching and temperature stability characteristics between the I and Q channels. Using a single voltage reference derived from U1 to set the gain for both the I and Q channels will improve the gain matching and stability. Further enhance­ments in gain matching and stability are achieved by using separate matching resistor networks for both R Additional trim capability via R
CAL1
and R
SET
can be added to
CAL2
and R
LOAD
.
compensate for any initial mismatch in gain between the two channels. This may be attributed to any mismatch between U1 and U2’s gain setting resistor, (R (R
); and/or voltage offset of each DAC’s control amplifier.
LOAD
); effective load resistance,
SET
The differential voltage outputs of U1 and U2 are fed into their respective differential inputs of a quadrature mixer via matching 50 filter networks.
REV. B
–17–
Page 18
AD9762
REFLO
R 2k*
R
CAL1
50
0.1␮F
R 2k*
R
CAL2
100
SET
SET
REFIO
FS ADJ
CLOCK
REFIO
FS ADJ
* OHMTEK ORNA1001F ** OHMTEK TOMC1603-50F
U1
I-CHANNEL
AVDD
REFLO
U2
Q-CHANNEL
CLOCK
CLOCK
IOUTA
IOUTB
IOUTA
IOUTB
50** R
LOAD
50** R
LOAD
Figure 57. Baseband QAM Implementation Using Two AD9762s
It is also possible to generate a QAM signal completely in the digital domain via a DSP or ASIC, in which case only a single DAC of sufficient resolution and performance is required to reconstruct the QAM signal. Also available from several vendors are Digital ASICs which implement other digital modulation schemes such as PSK and FSK. This digital implementation has the benefit of generating perfectly matched I and Q components in terms of gain and phase, which is essential in maintaining optimum performance in a communication system. In this implementation, the reconstruction DAC must be operating at a sufficiently high clock rate to accommodate the highest specified QAM carrier frequency. Figure 58 shows a block diagram of such an implementation using the AD9762.
50** R
LOAD
50** R
LOAD
TO NYQUIST FILTER AND MIXER
TO NYQUIST FILTER AND MIXER
AD9762 EVALUATION BOARD General Description
The AD9762-EB is an evaluation board for the AD9762 12-bit D/A converter. Careful attention to layout and circuit design combined with a prototyping area allow the user to easily and effectively evaluate the AD9762 in any application where high resolution, high speed conversion is required.
This board allows the user the flexibility to operate the AD9762 in various configurations. Possible output configurations include transformer coupled, resistor terminated, inverting/noninverting and differential amplifier outputs. The digital inputs are designed to be driven directly from various word generators, with the on-board option to add a resistor network for proper load termination. Provisions are also made to operate the AD9762 with either the internal or external reference, or to exercise the power-down feature.
Refer to the application note AN-420 “Using the AD9760/ AD9762/AD9764-EB Evaluation Board” for a thorough description and operating instructions for the AD9762 evaluation board.
I DATA
Q DATA
CARRIER
FREQUENCY
12
12
12
STEL-1130
QAM
12
SIN
STEL-1177
NCO
12
AD9762
12
COS
CLOCK
50
Figure 58. Digital QAM Architecture
LPF
50
TO MIXER
–18–
REV. B
Page 19
AVCC
AVEE
AGND
AVDD
DGND
DVDD
AD9762
TP13
A
B
2
1
3
JP3
TP8
C9
0.1␮F
A
AVDD
C8
0.1␮F
C7
1F
3
2
CLK
JP1
1
AB
R15
49.9
TP1
J1
EXTCLK
A
DVDD
C6
10␮F
TP7
B6
A
C5
10␮F
TP6
B5
TP5
TP19
TP18
B4
B3
B2
B1
TP4
TP2
TP3
A
C4
10␮F
DVDD
C3
10␮F
U1
R7
R3
16 PINDIP
R5
R1
2827262524
DVDD
CLOCK
AD976x
DB13
DB12
123456789
10 98765432
1
10 98765432
1
16151413121110
RES PK
1234567
C19C1C2
10 98765432
1
10 98765432
1
13579
P1
246
OUT 2
OUT 1
TP10 TP9
TP11
AVDD
ACOM
REFIO
FS ADJ
COMP1
DB5
DB4
DB3
DB2
1011121314
16 PINDIP
15
16
SLEEP
REFLO
DB1
DB0
RES PK
25
2729313335
23222120191817
NC
AVDD
DCOM
IOUTA
IOUTB
COMP2
DB11
DB10
DB9
DB8
DB7
DB6
9
8
C25
C26
C27
C28
C29
11131517192123
8
101214161820222426283032343638
C10
R16
2k
C11
AVDD
A
A
CT1
1615141312
12345
C30
C31
C32
C33
37
0.1␮F
TP14
0.1␮F
1
C34
AVDD
JP4
2
3
A A A
JP2
J2
PDIN
R17
49.9
TP12
1
DVDD
R8
1098765432
1
R4
1098765432
11
10
6
7
C35
C36
39
40
1098765432
98765432
10
1
DVDD
R6
1
R2
AVCC
R18
C17
0.1␮F
AVCC
U6
R42
1k
6
VOUT
U7
GND
REF43
VIN
2
C16
AVCC
C18
J6
C22
1F
A
C21
0.1␮F 6
7
U4
3
1k
JP8
A
JP7A
JP7B
R12
JP6A
J7
C12
OUT1
R20
J3
A
7
3
R43
4
A
1F
0.1␮F
R37
AD8047
2
B
B
B
OPEN
T1
4
22pF
49.9
6
AD8047
CW
5k
A
A
49.9
4
R10
1k
A
0
C20
3
2
A
A
A
5
A A
A
R14
AVEE
4
0
123
JP5
R45
1k
C14
1F
J5
EXTREFIN
R36
1k
JP6B
1
6
A
A
R13
R35
A
R9
C15
1k
1k
OPEN
A
J4
0.1␮F
R44
C24
C23
OUT2
R46
50
A
1k
A
A
1F
A
0.1␮F
AVEE
B
A
JP9
A
C13
22pF
R38
49.9
A A
REV. B
Figure 59. AD9762 Evaluation Board Schematic
–19–
Page 20
AD9762
Figure 60. Silkscreen LayerTop
Figure 61. Component Side PCB Layout (Layer 1)
–20–
REV. B
Page 21
AD9762
Figure 62. Ground Plane PCB Layout (Layer 2)
REV. B
Figure 63. Power Plane PCB Layout (Layer 3)
–21–
Page 22
AD9762
Figure 64. Solder Side PCB Layout (Layer 4)
Figure 65. Silkscreen LayerBottom
–22–
REV. B
Page 23
OUTLINE DIMENSIONS
Dimensions shown in inches and (mm).
28-Lead, 300 Mil SOIC
(R-28)
0.7125 (18.10)
0.6969 (17.70)
AD9762
28 15
1
PIN 1
0.0500
0.0118 (0.30)
0.0040 (0.10)
28 15
PIN 1
0.006 (0.15)
0.002 (0.05)
(1.27)
BSC
0.0192 (0.49)
0.0138 (0.35)
0.386 (9.80)
0.378 (9.60)
0.2992 (7.60)
0.2914 (7.40)
14
0.1043 (2.65)
0.0926 (2.35)
SEATING
0.0125 (0.32)
PLANE
0.0091 (0.23)
28-Lead, TSSOP
(RU-28)
0.177 (4.50)
0.169 (4.30)
141
0.0433 (1.10) MAX
0.4193 (10.65)
0.3937 (10.00)
0.0291 (0.74)
0.0098 (0.25)
8 0
0.256 (6.50)
0.246 (6.25)
C2201b–1–3/00 (rev. B)
45
0.0500 (1.27)
0.0157 (0.40)
REV. B
SEATING
PLANE
0.0256 (0.65) BSC
0.0118 (0.30)
0.0075 (0.19)
0.0079 (0.20)
0.0035 (0.090)
23
8 0
0.028 (0.70)
0.020 (0.50)
PRINTED IN U.S.A.
Loading...