Datasheet AD7709 Datasheet (Analog Devices)

Download

Page 1

16-Bit - ADC with

FEATURES 16-Bit - ADC Programmable Gain Front End Simultaneous 50 Hz and 60 Hz Rejection at 20 Hz

Update Rate

VREF Select

Measurement Capability

ISOURCE Select

16-Bit No Missing Codes 13-Bit p-p Resolution @ 20 Hz, 20 mV Range 16-Bit p-p Resolution @ 20 Hz, 2.56 V Range

INTERFACE 3-Wire Serial SPI®, QSPI™, MICROWIRE™, and DSP Compatible Schmitt Trigger on SCLK

POWER Specified for Single 3 V and 5 V Operation Normal: 1.25 mA Typ @ 3 V Power-Down: 7 A (32.768 kHz Crystal Running)

ON-CHIP FUNCTIONS Rail-to-Rail Input Buffer and PGA Selectable Reference Inputs 3 Switchable, Ratioed Current Sources for

4-Bit Digital I/O Port Low-Side Power Switches

™ Allows Absolute and Ratiometric

™

Measurements

Switchable Current Sources

AD7709

APPLICATIONS Sensor Measurement Temperature Measurement Pressure Measurements Weigh Scales Portable Instrumentation 4–20 mA Loops

GENERAL DESCRIPTION

The AD7709 is a complete analog front end for low frequency measurement applications. It contains a 16-bit ⌺-⌬ ADC, selectable reference inputs, three switchable matched excitation current sources, low-side power switches, and a digital I/O port. The 16-bit channel with PGA accepts fully differential, unipolar, and

bipolar input signal ranges from 1.024 ⫻ REFIN/128 to

1.024 ⫻ REFIN. It can be configured as two fully differential input channels or four pseudo-differential input channels. Signals can be converted directly from a transducer without the need for signal conditioning.

The device operates from a 32.768 kHz crystal with an on-chip PLL generating the required internal operating frequency. The output data rate from the part is software programmable. The p-p

resolution from the part varies with the programmed gain

and output data rate.

The part operates from a single 3 V or 5 V supply. When operating from 3 V supplies, the power dissipation for the part is 3.75 mW. The AD7709 is housed in a 24-lead TSSOP package.

FUNCTIONAL BLOCK DIAGRAM

IOUT1

IOUT2

AIN1

AIN2 AIN3/P3 AIN4/P4

AINCOM

IEXC1

MUX

AD7709

IEXC2

IEXC3

I = 25A

BUF

PGA

GND

REV. A

Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other rights of third parties that may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Analog Devices. Trademarks and registered trademarks are the property of their respective companies.

XTAL2REFIN1(–) REFIN2(–)REFIN1(+) REFIN2(+) XTAL1

OSCILLATOR

AND

PLL

DOUT

SERIAL

INTERFACE

AND

CONTROL

16-BIT - ADC

PWRGND

I/O PORT

LOGIC

P1/SW1 P2/SW2

DIN

SCLK

CS RDY RESET

Page 2

AD7709

FEATURES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

GENERAL DESCRIPTION . . . . . . . . . . . . . . . . . . . . . . . . . 1

FUNCTIONAL BLOCK DIAGRAM . . . . . . . . . . . . . . . . . 1

SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

TIMING CHARACTERISTICS . . . . . . . . . . . . . . . . . . . . . 6

ABSOLUTE MAXIMUM RATINGS . . . . . . . . . . . . . . . . . 8

ORDERING GUIDE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

PIN CONFIGURATION . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

PIN FUNCTION DESCRIPTIONS . . . . . . . . . . . . . . . . . . 9

TYPICAL PERFORMANCE CHARACTERISTICS . . . . 10

ADC CIRCUIT INFORMATION . . . . . . . . . . . . . . . . . . . 11

Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

S-D ADC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

NOISE PERFORMANCE . . . . . . . . . . . . . . . . . . . . . . . . . 13

ON-CHIP REGISTERS . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Communications Register . . . . . . . . . . . . . . . . . . . . . . . . 14

Status Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Configuration Register . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Filter Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

ADC Data Result Register . . . . . . . . . . . . . . . . . . . . . . . . 18

CONFIGURING THE AD7709 . . . . . . . . . . . . . . . . . . . . . 19

DIGITAL INTERFACE . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

MICROCOMPUTER/MICROPROCESSOR

INTERFACING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

AD7709-to-68HC11 Interface . . . . . . . . . . . . . . . . . . . . . 21

AD7709-to-8051 Interface . . . . . . . . . . . . . . . . . . . . . . . . 21

AD7709-to-ADSP-2103/ADSP-2105 Interface . . . . . . . . 21

CIRCUIT DESCRIPTION . . . . . . . . . . . . . . . . . . . . . . . . 22

Analog Input Channels . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Programmable Gain Amplifier . . . . . . . . . . . . . . . . . . . . . 23

Bipolar/Unipolar Configuration . . . . . . . . . . . . . . . . . . . . 23

Data Output Coding . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Excitation Currents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Crystal Oscillator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Reference Input . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Reset Input . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Power-Down Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Grounding and Layout . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

APPLICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

Pressure Measurement . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

Temperature Measurement . . . . . . . . . . . . . . . . . . . . . . . 26

3-Wire RTD Configurations . . . . . . . . . . . . . . . . . . . . . . 27

Smart Transmitters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

OUTLINE DIMENSIONS . . . . . . . . . . . . . . . . . . . . . . . . . 29

Revision History . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

–2–

REV. A

Page 3

AD7709

(VDD = 2.7 V to 3.6 V or 4.75 V to 5.25 V, REFIN(+) = 2.5 V; REFIN(–) = GND; GND = 0 V; XTAL1/XTAL2 =

2, 4

32.768 kHz Crystal; all specifications T

105 Hz max

16 Bits min 20 Hz Update Rate

16 Bits p-p ± 2.56 V Range, 20 Hz Update Rate

± 30 ppm of FSR max Typically 2 ppm

± 0.75 LSB typ B Grade, VDD = 4 V ± 0.2 % of FS typ A Grade

±¥1 024. REFIN

GAIN

GND + 100 mV V min

– 100 mV V max

± 1 nA max

GND – 30 mV V min

+ 30 mV V max

100 dB min 50 Hz ± 1 Hz, Range = ± 2.56 V, AIN = 1 V 100 dB min 60 Hz ± 1 Hz, Range = ± 2.56 V, AIN = 1 V

1V min V

GND – 30 mV V min

+ 30 mV V max

to T

MIN

, unless otherwise noted.)

MAX

FSR

¥21024.

GAIN

100 dB typ on ± 20 mV Range

V nom REFIN = REFIN(+) – REFIN(–)

GAIN = 1 to 128

50 Hz ± 1Hz, 16.65 Hz Update Rate, SF = 82

110 dB typ on ± 20 mV Range

V max

REFIN

SPECIFICATIONS

Parameter AD7709A, AD7709B Unit Test Conditions

ADC CHANNEL SPECIFICATION

Output Update Rate 5.4 Hz min 0.732 ms Increments

ADC CHANNEL

No Missing Codes Resolution 13 Bits p-p ± 20 mV Range, 20 Hz Update Rate

Output Noise and Update Rates See Tables II to V Integral Nonlinearity Offset Error ± 3 mV typ Offset Error Drift vs. Temperature ± 10 nV/∞C typ Full-Scale Error

Gain Drift vs. Temperature ± 0.5 ppm/∞C typ Power Supply Rejection (PSR) 85 dB typ Input Range = ± 2.56 V

ANALOG INPUTS

Differential Input Voltage Ranges

ADC Range Matching ± 2 mV typ Input Voltage = 19 mV on All Ranges Absolute AIN1–AIN4 Voltage Limits

AIN1–AIN4 Analog Input Current

DC Input Current DC Input Current Drift ± 5 pA /∞C typ

Absolute AINCOM Voltage Limits

AINCOM Analog Input Current Pseudo-Differential Mode of Operation

DC Input Current ± 125 nA/V typ Input Current Varies with Input Range DC Input Current Drift ± 2 pA/V/∞C typ

Normal-Mode Rejection

@ 50 Hz 100 dB min @ 60 Hz 100 dB min 60 Hz ± 1 Hz, 20 Hz Update Rate, SF = 68

Common-Mode Rejection

@ DC 100 dB typ Input Range = ± 2.56 V, AIN = 1 V

@ 50 Hz @ 60 Hz

REFERENCE INPUTS (REFIN1 and REFIN2)

REFIN Voltage 2.5 V nom REFIN = REFIN(+) – REFIN(–) REFIN Voltage Range

Absolute REFIN Voltage Limits

Average Reference Input Current 0.5 mA/V typ Average Reference Input Current Drift ± 0.01 nA/V/∞C typ Normal-Mode Rejection

@ 50 Hz 100 dB min 50 Hz ± 1 Hz, SF = 82 @ 60 Hz 100 dB min 60 Hz ± 1 Hz, SF = 68

Common-Mode Rejection

@ DC 110 dB typ Input Range = ± 2.56 V, AIN = 1 V @ 50 Hz 110 dB typ 50 Hz ± 1 Hz, Range = 2.56 V, AIN = 1 V @ 60 Hz 110 dB typ 60 Hz ± 1 Hz, Range = 2.56 V, AIN = 1 V

See Notes on page 5.

REV. A

–3–

Page 4

AD7709

SPECIFICATIONS

(continued)

Parameter AD7709A, AD7709B Unit Test Conditions

EXCITATION CURRENT SOURCES

(IEXC1, IEXC2, and IEXC3)

Output Current

IEXC1, IEXC2 200 mA nom IEXC3 25 mA nom

Initial Tolerance at 25∞C ± 10 % typ Drift 200 ppm/∞C typ Initial Current Matching at 25∞C ± 2.5 % max B Grade, No Load

(between IEXC1 and IEXC2) ± 2.5 % typ A Grade, No Load

Drift Matching

(between IEXC1 and IEXC2) 20 ppm/∞C typ

Initial Current Matching at 25∞C ± 5% max B Grade, No Load

(between 8 ⫻ IEXC3 and IEXC1/IEXC2) ± 5% typ A Grade, No Load

Drift Matching

(between 8 ⫻ IEXC3 and IEXC1/IEXC2) 20 ppm/∞C typ

Line Regulation V

= 5 V ± 5%

IEXC1, IEXC2 1.25 mA/V typ A, B Grades

2.6 mA/V max B Grade

IEXC3 1 mA/V max B Grade

1 mA/V typ A Grade

Load Regulation 300 nA/V typ Output Compliance V

– 0.6 V max

GND –30 mV V min

LOW-SIDE POWER SWITCHES

(SW1 and SW2)

3 W typ VDD = 5 V, A and B Grade 5 W max B Grade

4.5 W typ V

Allowable Current

LOGIC INPUTS

All Inputs Except SCLK and XTAL1

, Input Low Voltage 0.8 V max VDD = 5 V

INL

7 W max B Grade 20 mA max Continuous Current per Switch

0.4 V max V

, Input High Voltage 2.0 V min VDD = 3 V or 5 V

INH

SCLK Only (Schmitt-Triggered Input)

T(+)

T(–)

– V

T(+)

V V V

XTAL1 Only

V V V V

T(–)

T(+)

T(–)

– V

T(+)

T(–)

, Input Low Voltage 0.8 V max VDD = 5 V

INL

, Input High Voltage 3.5 V min VDD = 5 V

INH

, Input Low Voltage 0.4 V max VDD = 3 V

INL

, Input High Voltage 2.5 V min VDD = 3 V

INH

1.4/2 V min/V max VDD = 5 V

0.8/1.4 V min/V max VDD = 5 V

0.3/0.85 V min/V max VDD = 5 V

0.95/2 V min/V max VDD = 3 V

0.4/1.1 V min/V max VDD = 3 V

0.3/0.85 V min/V max VDD = 3 V

Input Currents (except XTAL) ± 2 mA max V

= 3 V, A and B Grade

= 3 V

= V

–70 mA max VIN = GND, Typically –40 mA @ 5 V and

–20 mA at 3 V; Weak Pull-Ups on the Logic Inputs

Input Capacitance 10 pF typ All Digital Inputs

–4–

REV. A

Page 5

AD7709

Parameter AD7709A,

LOGIC OUTPUTS (Excluding XTAL2)

, Output High Voltage

VOL, Output Low Voltage

, Output High Voltage

, Output Low Voltage

VDD – 0.6 V min VDD = 3 V, I

0.4 V max VDD = 3 V, I 4V min VDD = 5 V, I

0.4 V max VDD = 5 V, I

AD7709

BUnit Test Conditions

SOURCE

SINK

SOURCE

SINK

= 100 mA

= 200 mA

= 1.6 mA

Floating-State Leakage Current ± 10 mA max Floating-State Output Capacitance ± 10 pF typ Data Output Coding Binary Unipolar Mode

Offset Binary Bipolar Mode

I/O PORT

, Input Low Voltage

INL

, Input High Voltage

INH

Input Currents ± 2 mA max V

0.8 V max VDD = 5 V

0.4 V max V

= 3 V

2.0 V min VDD = 3 V or 5 V = V

–70 mA max VIN = GND, Typically –40 mA @ VDD = 5 V

and –20 mA at V

= 3 V; Weak Pull-Ups on

the Logic Inputs

Input Capacitance 10 pF typ All Digital Inputs

, Output High Voltage

, Output Low Voltage

, Output High Voltage

VOL, Output Low Voltage

VDD – 0.6 V min VDD = 3 V, I

0.4 V max VDD = 3 V, I

4V min VDD = 5 V, I

0.4 V max VDD = 5 V, I

SOURCE

= 100 mA

SINK

SOURCE

= 1.6 mA

SINK

= 100 mA

= 200 mA

Floating-State Output Leakage Current ± 10 mA max Floating-State Output Capacitance ±10 pF typ

START-UP TIME

From Power-On 300 ms typ From Standby Mode 1 ms typ OSCPD = 0 From Power-Down Mode 300 ms typ OSCPD = 1

POWER REQUIREMENTS

Power Supply Voltage

– GND 2.7/3.6 V min/max VDD = 3 V nom

4.75/5.25 V min/max V

= 5 V nom

Power Supply Currents

Current 1.5 mA max VDD = 3 V, 1.25 mA typ

1.75 mA max V

(Low Power Mode) 7 mA max B Grade, VDD = 3 V, Standby Mode

= 5 V, 1.45 mA typ

7 mA typ A Grade, VDD = 3 V, Standby Mode

1.5 mA max B Grade, V

1.5 mA typ A Grade, V

= 3 V, Power-Down Mode

26 mA max B Grade, VDD = 5 V, Standby Mode 26 mA typ A Grade, V

6.5 mA max B Grade, V

6.5 mA typ A Grade, VDD = 5 V, Power-Down Mode

134

mA typ VDD = 3 V, Standby Mode mA typ VDD = 5 V, Standby Mode

for One Conversion Second 107

NOTES

Temperature Range –40∞C to +85∞C.

Guaranteed by design and/or characterization data on production release.

Full-scale error applies to both positive and negative full scale.

Simultaneous 50 Hz and 60 Hz rejection is achieved using 19.79 Hz update rate. Normal mode rejection in this case is 60 dB min.

When the part is placed in power-down mode for a single conversion/second, at an update rate of 19.79 Hz, the current consumption is higher compared to when the part is placed in standby mode as the crystal oscillator takes approximately 100 ms to begin clocking. The device will, therefore, use full current for the conversion time and the 100 ms period required for the oscillator to begin clocking. However, if the conversion rate is lower, the current consumption will be reduced so that it is worthwhile to use the power-down rather than the standby mode.

Specifications subject to change without notice.

= 5 V, Standby Mode

= 5 V, Power-Down Mode

REV. A

–5–

Page 6

AD7709

TIMING CHARACTERISTICS

Limit at T

MIN

(VDD = 2.7 V to 3.6 V or VDD = 4.75 V to 5.25 V; GND = 0 V; X

1, 2

Logic 1 = VDD unless otherwise noted.)

, T

MAX

= 32.768 kHz; Input Logic 0 = 0 V,

TAL

Parameter (A, B Version) Unit Conditions/Comments

30.5176

typ Crystal Oscillator Period

50 ns min RESET Pulsewidth

Read Operation

0 ns min RDY to CS Setup Time 0 ns min CS Falling Edge to SCLK Active Edge Setup Time 0 ns min SCLK Active Edge to Data Valid Delay

60 ns max VDD = 4.75 V to 5.25 V

4, 5

80 ns max V 0 ns min CS Falling Edge to Data Valid Delay 60 ns max V 80 ns max V

100 ns min SCLK High Pulsewidth 100 ns min SCLK Low Pulsewidth 0 ns min CS Rising Edge to SCLK Inactive Edge Hold Time 10 ns min Bus Relinquish Time after SCLK Inactive Edge 80 ns max

100 ns max SCLK Active Edge to RDY High

Write Operation

NOTES

Sample tested during initial release to ensure compliance. All input signals are specified with tR = tF = 5 ns (10% to 90% of VDD) and timed from a voltage level of 1.6 V.

See Figures 2 and 3.

SCLK active edge is falling edge of SCLK.

These numbers are measured with the load circuit of Figure 1 and defined as the time required for the output to cross the V

This specification comes into play only if CS goes low while SCLK is low. It is required primarily for interfacing to DSP machines.

These numbers are derived from the measured time taken by the data output to change 0.5 V when loaded with the circuit of Figure 1. The measured number is then extrapolated back to remove effects of charging or discharging the 50 pF capacitor. This means that the times quoted in the Timing Characteristics table are the true bus relinquish times of the part and as such are independent of external bus loading capacitances.

RDY returns high after a read of the ADC. The same data can be read again, if required, while RDY is high, although care should be taken that subsequent reads do not occur close to the next output update.

0 ns min CS Falling Edge to SCLK Active Edge Setup Time 30 ns min Data Valid to SCLK Edge Setup Time 25 ns min Data Valid to SCLK Edge Hold Time 100 ns min SCLK High Pulsewidth 100 ns min SCLK Low Pulsewidth 0 ns min CS Rising Edge to SCLK Edge Hold Time

= 2.7 V to 3.6 V

= 4.75 V to 5.25 V

= 2.7 V to 3.6 V

or VOH limits.

3, 7

–6–

REV. A

Page 7

(1.6mA WITH VDD = 5V

SINK

100A WITH V

AD7709

= 3V)

SCLK

DIN

RDY

TO OUTPUT

50pF

SOURCE

1.6V

(200A WITH VDD = 5V

100A WITH V

= 3V)

Figure 1. Load Circuit for Timing Characterization

MSB

LSB

Figure 2. Write Cycle Timing Diagram

SCLK

DOUT

LSB

MSB

Figure 3. Read Cycle Timing Diagram

REV. A

–7–

Page 8

AD7709

ABSOLUTE MAXIMUM RATINGS*

(TA = 25∞C, unless otherwise noted.)

VDD to GND . . . . . . . . . . . . . . . . . . . . . . . . . . –0.3 V to +7 V

PWRGND to AGND . . . . . . . . . . . . . . –20 mV to +20 mV

Analog Input Voltage to GND . . . . . –0.3 V to V

Reference Input Voltage to GND . . . –0.3 V to V

+ 0.3 V

Total AIN/REFIN Current (Indefinite) . . . . . . . . . . 30 mA

Digital Input Voltage to GND . . . . . . . –0.3 V to V

+ 0.3 V

Digital Output Voltage to GND . . . . –0.3 V to VDD + 0.3 V

Operating Temperature Range . . . . . . . . . . –40∞C to +85∞C

Storage Temperature Range . . . . . . . . . . . . –65∞C to +150∞C

Junction Temperature . . . . . . . . . . . . . . . . . . . . . . . . . 150∞C

Thermal Impedance . . . . . . . . . . . . . . . . . . . 97.9∞C/W

Thermal Impedance . . . . . . . . . . . . . . . . . . . . . 14∞C/W

Lead Temperature, Soldering

Vapor Phase (60 sec) . . . . . . . . . . . . . . . . . . . . . . . . 215∞C

Infrared (15 sec) . . . . . . . . . . . . . . . . . . . . . . . . . . . 220∞C

*Stresses above those listed under Absolute Maximum Ratings may cause perma-

nent damage to the device. This is a stress rating only; functional operation of the device at these or any other conditions above those listed in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability.

ORDERING GUIDE

Temperature Package Package

Model Range Description Option

AD7709ARU –40∞C to +85∞C TSSOP RU-24 AD7709BRU –40∞C to +85∞C TSSOP RU-24 EVAL-AD7709EB Evaluation Board

PIN CONFIGURATION

IOUT1

IOUT2

REFIN1(+)

REFIN1(–)

AIN1

AIN2

AIN3/P3

AIN4/P4

AINCOM

REFIN2(+)

REFIN2(–)

P2/SW2

AD7709

TOP VIEW

(Not to Scale)

XTAL1

XTAL2

GND

DIN

DOUT

RDY

SCLK

RESET

P1/SW1

PWRGND

CAUTION

ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily accumulate on the human body and test equipment and can discharge without detection. Although the

WARNING!

AD7709 features proprietary ESD protection circuitry, permanent damage may occur on devices subjected to high energy electrostatic discharges. Therefore, proper ESD precautions are recommended to avoid performance degradation or loss of functionality.

ESD SENSITIVE DEVICE

–8–

REV. A

Page 9

AD7709

PIN FUNCTION DESCRIPTIONS

Pin No. Mnemonic Function

1 IOUT1 Output for Internal Excitation Current Source. Either current source IEXC1, IEXC2, IEXC3, or a combina-

tion of the current sources, can be switched to this output.

2 IOUT2 Output for Internal Excitation Current Source. Either current source IEXC1, IEXC2, IEXC3, or a combina-

tion of the current sources, can be switched to this output.

3 REFIN1(+) Positive Reference Input. REFIN1(+) can lie anywhere between V

voltage (REFIN1(+) – REFIN1(–)) is 2.5 V, but the part is functional with a reference range from 1 V to VDD.

ence 4 REFIN1(–) Negative Reference Input. This reference input can lie anywhere between GND and VDD – 1 V. 5 AIN1 Analog Input. Programmable gain input that can be used as a pseudo-differential input when used with

AINCOM or as the positive input of a fully differential input pair when used with AIN2. 6 AIN2 Analog Input. Programmable gain input that can be used as a pseudo-differential input when used with

AINCOM or as the negative input of a fully differential input pair when used with AIN1. 7 AIN3/P3 Analog Input/Digital Port Bit. Programmable gain input that can be used as a pseudo-differential input when

used with AINCOM or as the positive input of a fully differential input pair when used with AIN4. This pin

can also be programmed as a general-purpose digital input bit. 8 AIN4/P4 Analog Input/Digital Port Bit. Programmable gain input that can be used as a pseudo-differential input when

used with AINCOM or as the negative input of a fully-differential input pair when used with AIN3. This pin

can also be programmed as a general-purpose digital input bit. 9 AINCOM All analog inputs are referenced to this input when configured in pseudo-differential input mode. 10 REFIN2(+) Positive Reference Input. REFIN2(+) can lie anywhere between V

voltage (REFIN2(+) – REFIN2(–)) is 2.5 V, but the part is functional with a reference range from 1 V to V 11 REFIN2(–) Negative Reference Input. This reference input can lie anywhere between GND and VDD – 1 V. 12 P2/SW2 Dual-Purpose Pin. It can act as a general-purpose output (P2) bit or as a low-side power switch (SW2) to

PWRGND. 13 PWRGND Ground Point for the Low-Side Power Switches SW2 and SW1. PWRGND must be tied to GND. 14 P1/SW1 Dual-Purpose Pin. It can act as a general-purpose output (P1) bit or as a low-side power switch (SW1) to

PWRGND. 15 RESET

Digital Input Used to Reset the ADC to Its Power-On-Reset Status. This pin has a weak pull-up internally to VDD. 16 SCLK Serial Clock Input for Data Transfers to and from the ADC. The SCLK has a Schmitt-triggered input making

the interface suitable for opto-isolated applications. The serial clock can be continuous with all data transmitted

in a continuous train of pulses. Alternatively, it can be a noncontinuous clock with the information being

transmitted to or from the AD7709 in smaller batches of data. A weak pull-up to V

SCLK input. 17 CS Chip Select Input. This is an active low logic input used to select the AD7709. CS can be used to select the

AD7709 in systems with more than one device on the serial bus or as a frame synchronization signal in com-

municating with the device. CS can be hardwired low allowing the AD7709 to operate in 3-wire mode with

SCLK, DIN, and DOUT used to interface with the device. A weak pull-up to VDD is provided on the CS input. 18 RDY RDY is a Logic Low Status Output from the AD7709. RDY is low if the ADC has valid data in its data

read, RDY will return high prior to the next update indicating to the user that a read operation should

not be initiated. 19 DOUT Serial Data Output Accessing the Output Shift Register of the AD7709. The output shift register can contain

data from any of the on-chip data or control registers. 20 DIN Serial Data Input Accessing the Input Shift Register on the AD7709. Data in this shift register is transferred to

the control registers within the ADC, the selection bits of the communications register selecting which

control register. A weak pull-up to V

is provided on the DIN input.

21 GND Ground Reference Point for the AD7709 22 V

Supply Voltage, 3 V or 5 V Nominal 23 XTAL2 Output from the 32.768 kHz Crystal Oscillator Inverter 24 XTAL1 Input to the 32.768 kHz Crystal Oscillator Inverter

and GND + 1 V. The nominal refer-

and GND + 1 V. The nominal reference

is provided on the

REV. A

–9–

Page 10

AD7709–Typical Performance Characteristics

32772

32771

32770

32769

32768

CODE READ

32767

32766

32765

32764

1000 200 400300

VDD = 5V

INPUT RANGE = 20mV UPDATE RATE = 19.79Hz

500

READING NUMBER

600 700 800 900 1000

REF

= 2.5V

= 25 C

TPC 1. Typical Noise Plot on ±20 mV Input Range

3.0

= 2.5V

= 25C

2.56V RANGE

20mV RANGE

2.5

2.0

VDD = 5V V

REF

1.5

INPUT RANGE = 2.56V UPDATE RATE = 19.79Hz

RMS NOISE – V

1.0

0.5

700

600

500

400

300

OCCURRENCE

200

100

VDD = 5V

= 25C

OSCILLATOR

3276732766 32768 3277032769

CODE

TPC 3. Noise Histogram

TIME BASE = 100ms/DIV TRACE 1 = TRACE 2 = 2V/DIV

32771

1.0 3.02.52.01.5 3.5 5.04.54.0

– V

REF

TPC 2. RMS Noise vs. Reference Input

TPC 4. Typical Oscillator Power-Up

–10–

REV. A

Page 11

AD7709

ADC CIRCUIT INFORMATION Overview

The AD7709 incorporates a ⌺-⌬ ADC channel with on-chip digital filtering intended for the measurement of wide dynamic range, low frequency signals such as those in weigh-scale, strain-gauge, pressure transducer, or temperature measurement applications.

⌺-⌬ ADC

This channel can be programmed to have one of eight input voltage ranges from ±20 mV to ± 2.56 V. This channel can be configured as either two fully differential inputs (AIN1/AIN2 and AIN3/AIN4) or four pseudo-differential input channels (AIN1/AINCOM, AIN2/AINCOM, AIN3/AINCOM, and AIN4/AINCOM). Buffering the input channel means that the part can accommodate significant source impedances on the analog input and that R, C filtering (for noise rejection or RFI reduction) can be placed on the analog inputs if required.

The ADC employs a ⌺-⌬ conversion technique to realize up to 16 bits of no-missing-codes performance. The ⌺-⌬ modulator converts the sampled input signal into a digital pulse train whose duty cycle contains the digital information. A Sinc

programmable low-pass filter is then employed to decimate the modulator output data stream to give a valid data conversion result at programmable output rates from 5.35 Hz (186.77 ms) to 105.03 Hz (9.52 ms). A chopping scheme is also employed to minimize ADC channel offset errors. A block diagram of the ADC input channel is shown in Figure 4.

The sampling frequency of the modulator loop is many times higher than the bandwidth of the input signal. The integrator in the modulator shapes the quantization noise (which results from the analog-to-digital conversion) so that the noise is pushed toward one-half of the modulator frequency. The output of the ⌺-⌬ modulator feeds directly into the digital filter. The digital filter then band-limits the response to a frequency significantly lower than one-half of the modulator frequency. In this manner, the 1-bit output of the comparator is translated into a bandlimited, low noise output from the AD7709 ADC. The AD7709 filter is a low-pass, Sinc

, or (SIN(x)/x)3 filter whose primary function is to remove the quantization noise introduced at the modulator. The cutoff frequency and decimated output data rate of the filter are programmable via the SF word loaded to the filter register.

A chopping scheme is employed where the complete signal chain is chopped, resulting in excellent dc offset and offset drift specifications, and is extremely beneficial in applications where drift, noise rejection, and optimum EMI rejection are important factors. With chopping, the ADC repeatedly reverses its inputs. The decimated digital output words from the Sinc3 filters therefore have a positive offset and negative offset term included. As a result, a final summing stage is included so that each output

word from the filter is summed and averaged with the previous filter output to produce a new valid output result to be written to the ADC data register.

The input chopping is incorporated into the input multiplexer while the output chopping is accomplished by an XOR gate at the output of the modulator. The chopped modulator bit stream is applied to a Sinc

filter. The programming of the Sinc3 deci-

mation factor is restricted to an 8-bit register SF, the actual decimation factor is the register value × 8. The decimated output rate from the Sinc

filter (and the ADC conversion rate) will

therefore be:

ADC MOD



318





=×







where:

is the ADC update rate.

ADC

SF is the decimal equivalent of the word loaded to the

filter register.

is the modulator sampling rate of 32.768 kHz.

MOD

Programming the filter register determines the update rate for the ADC. The chop rate of the channel is half the output data rate.

The frequency response of the filter H(f ) is as follows:

 

 





sin ( )

SF f/ f

×××

sin ( )

××

f/f

OUT

f/f

OUT

f/f

 



MOD



 

where:

= 32,768 Hz.

MOD

SF = value programmed into Filter Register.

OUT

= f

/(SF ⫻ 8 ⫻ 3)

MOD

The following shows plots of the filter frequency response for the SF words shown in Table I. The overall frequency response is the product of a Sinc at integer multiples of 3 ⫻ f integer multiples of f

and a sinc response. There are Sinc3 notches

, and there are sinc notches at odd

ADC

/2. The 3 dB frequency for all values of SF

ADC

obeys the following equation:

fdB f

3024

=×.

()

ADC

The signal chain is chopped as shown in Figure 4. The chop frequency is:





ADC









CHOP

REV. A

ANALOG

INPUT

CHOP

MUX

BUF

PGA

MOD

⌺-⌬

MOD

CHOP

XOR

(

Figure 4. ADC Channel Block Diagram

–11–

8 ⴛ SF

⌺

)

SINC3 FILTER

3 ⴛ

(8 ⴛ SF )

ADC

AIN + V AIN – V

⌺

DIGITAL OUTPUT

Page 12

AD7709

As shown in the block diagram, the Sinc3 filter outputs alternately contain +VOS and –VOS, where VOS is the respective channel offset. This offset is removed by performing a running average of 2, which means that the settling time to any change in programming of the ADC will be twice the normal conversion time, while an asynchronous step change on the analog input will not be fully reflected until the third subsequent output.

=¥

SETTLE

ADC

˜ ¯

ADC

The allowable range for SF is 13 to 255, with a default of 69 (45H). The corresponding conversion rates, conversion times, and settling times are shown in Table I. Note that the conversion time increases by 0.732 ms for each increment in SF.

–20

–40

–60

–80

–100

–120

–140

ATTENUATION – dB

–160

–180

–200

100

SF = 13 OUTPUT DATA RATE = 105Hz INPUT BANDWIDTH = 25.2Hz FIRST NOTCH = 52.5Hz 50Hz REJECTION = –23.6dB, 50Hz  1Hz REJECTION = –20.5dB 60Hz REJECTION = –14.6dB, 60Hz  1Hz REJECTION = –13.6dB

150 200 250 300 350 400

FREQUENCY – Hz

450 500 550 600

650

700

Figure 5. Filter Profile with SF = 13

–20

–40

–60

–80

–100

ATTENUATION – dB

–120

–140

–160

0 10010

SF = 82 OUTPUT DATA RATE = 16.65Hz INPUT BANDWIDTH = 4Hz 50Hz REJECTION = –171dB, 50Hz  1Hz REJECTION = –100dB 60Hz REJECTION = –58dB, 60Hz  1Hz REJECTION = –53dB

20 30 40 50 60 70 80 90

FREQUENCY – Hz

Figure 6. Filter Profile with SF = 82

Table I. ADC Conversion and Settling Times for Various SF Words

Data Update Rate Settling Time

SF Word f

(Hz) t

ADC

SETTLE

(ms)

13 105.3 19.04 69 (Default) 19.79 101.07 255 5.35 373.54

Normal mode rejection is the major function of the digital filter on the AD7709. The normal mode 50 ± 1 Hz rejection with an SF word of 82 is typically –100 dB. The 60 ± 1 Hz rejection with SF = 68 is typically –100 dB. Simultaneous 50 Hz and 60 Hz rejection of better than 60 dB is achieved with an SF of 69. Choosing an SF word of 69 places notches at both 50 Hz and 60 Hz. Figures 5 to 8 show the filter rejection for a selection of SF words.

–20

–40

–60

–80

–100

ATTENUATION – dB

–120

–140

–160

0 100

SF = 69 OUTPUT DATA RATE = 19.8Hz INPUT BANDWIDTH = 4.74Hz FIRST NOTCH = 9.9Hz 50Hz REJECTION = –66dB, 50Hz  1Hz REJECTION = –60dB 60Hz REJECTION = –117dB, 60Hz  1Hz REJECTION = –94dB

20 30 40 50 60 70 80 90

FREQUENCY – Hz

Figure 7. Filter Profile with Default SF = 69 Giving Filter Notches at Both 50 Hz and 60 Hz

–20

–40

–60

–80

–100

ATTENUATION – dB

–120

–140

–160

0 10010

SF = 255 OUTPUT DATA RATE = 5.35Hz INPUT BANDWIDTH = 1.28Hz 50Hz REJECTION = –93dB, 50Hz  1Hz REJECTION = –93dB 60Hz REJECTION = –74dB, 60Hz  1Hz REJECTION = –68dB

20 30 40 50 60 70 80 90

FREQUENCY – Hz

Figure 8. Filter Profile with SF = 255

–12–

REV. A

Page 13

AD7709

NOISE PERFORMANCE

Tables II and III show the output rms noise and output peak-topeak resolution in bits (rounded to the nearest 0.5 LSB) for a selection of output update rates. The numbers are typical and generated at a differential input voltage of 0 V. The output update rate is selected via the SF7–SF0 bits in the Filter Register. It is important to note that the peak-to-peak resolution figures

level and is independent of frequency. The quantization noise starts at an even lower level but rises rapidly with increasing frequency to become the dominant noise source. are given for the bipolar input ranges. the rms noise numbers will be the same the peak-to-peak resolution is now based

The numbers in the tables

For the unipolar ranges,

as the bipolar range, but

on half the signal range,

which effectively means losing 1 bit of resolution. represent the resolution for which there will be no code flicker within a six-sigma limit. The output noise comes from two sources. The first is the electrical noise in the semiconductor devices (device noise) used in the implementation of the modulator. Second, when the analog input is converted into the digital domain, quantization noise is added. The device noise is at a low

ON-CHIP REGISTERS

The AD7709 is controlled and configured via a number of on-chip

registers, as shown in Figure 9 and described in more detail in the

following pages. In the following descriptions, set implies a Logic 1

state and cleared implies a Logic 0 state, unless otherwise stated.

Table II. Typical Output RMS Noise vs. Input Range and Update Rate for the AD7709 (Output RMS Noise in V)

SF Data Update

Input Range

Word Rate (Hz) 20 mV 40 mV 80 mV 160 mV 320 mV 640 mV 1.28 V 2.56 V

13 105.3 1.50 1.50 1.60 1.75 3.50 4.50 6.70 11.75 69 19.79 0.60 0.65 0.65 0.65 0.65 0.95 1.40 2.30 255 5.35 0.35 0.35 0.37 0.37 0.37 0.51 0.82 1.25

Table III. Peak-to-Peak Resolution vs. Input Range and Update Rate for the AD7709 (Peak-to-Peak Resolution in Bits)

SF Data Update

Input Range

Word Rate (Hz) 20 mV 40 mV 80 mV 160 mV 320 mV 640 mV 1.28 V 2.56 V

13 105.3 12 13 14 15 15 15.5 16 16 69 19.79 13 14 15 16 16 16 16 16 255 5.35 14 15 16 16 16 16 16 16

DIN

DOUT

WEN

R/W STBY

DIN

OSCPD 0 0 A1 A0

ADC STATUS REGISTER

(8 BITS)

CONFIGURATION REGISTER

(24 BITS)

FILTER REGISTER

(8 BITS)

ADC DATA REGISTER

(16 BITS)

Figure 9. On-Chip Registers

SELECT

DECODER

REV. A

–13–

Page 14

AD7709

Communications Register (A1, A0 = 0, 0)

The Communications Register is an 8-bit write-only register. All communications to the part must start with a write operation to the Communications Register. The data written to the Communications Register determines whether the next operation is a read or write operation, and to which register this operation takes place. For read or write operations, once the subsequent read or write operation to the selected register is complete, the interface returns to where it expects a write operation to the Communications Register. This is the default state of the interface, and on power-up or after a RESET, the AD7709 is in this default state waiting for a write operation to the Communications Register. In situations where the interface sequence is lost, a write operation of at least 32 serial clock cycles with DIN high, returns the AD7709 to this default state by resetting the part. Table IV outlines the bit designations for the Communications Register. CR0 to CR7 indicate the bit location, CR denoting the bits are in the Communications Register. denotes the first bit of the data stream.

7RC6RC5RC4RC3RC2RC1RC0RC

CR7

NEW )0(

Bit Bit Location Name Description

CR7 WEN Write Enable Bit.

CR6 R/W A 0 in this bit location indicates that the next operation will be a write to a specified register.

CR5 STBY Standby Bit Location.

CR4 OSCPD Oscillator Power-Down Bit.

CR3–CR2 0 These bits must be programmed with a Logic 0 for correct operation.

CR1–CR0 A1–A0 Register Address Bits. These address bits are used to select which of the AD7709 registers are accessed

/R W )0()0(YBTS)0(DPCSO)0(0)0(0)0(1A)0(A

Table IV. Communications Register Bit Designations

A 0 must be written to this bit so the write operation to the Communications Register If a 1 is written to this bit, the part will not clock on to subsequent bits in the register. bit location until a 0 is written to this bit. Once a 0 is written to the WEN bit, the next seven bits will be loaded to the Communications Register.

A 1 in this position indicates that the next operation will be a read from the designated register.

A 1 in this location places the AD7709 in low power mode. A 0 in this location powers up the AD7709.

If this bit is set, placing the AD7709 in standby mode will stop the crystal oscillator also, reducing the power consumed by the part to a minimum. The oscillator will require 300 ms to begin oscillating when the ADC is taken out of power-down mode. If this bit is cleared, the oscillator is not stopped when the ADC is placed in power-down mode. When the ADC is taken out of power-down mode, the oscillator does not require the 300 ms start-up time.

during this serial interface communication.

actually takes place.

It will stay at this

Table V. Register Selection Table

A1 A0 Register

00Communications Register during a Write Operation 00Status Register during a Read Operation 01Configuration Register 10Filter Register 11ADC Data Register

–14–

REV. A

Page 15

AD7709

Status Register (A1, A0 = 0, 0; Power-On-Reset = 00H)

The ADC Status Register is an 8-bit read-only register. To access the ADC Status Register, the user must write to the Communications Register, selecting the next operation to be a read and load bits A1–A0 with 0, 0. Table VI outlines the bit designations for the Status Register. SR0 to SR7 indicate the bit location, SR denoting the bits are in the Status Register. SR7 denotes the first bit of the data stream. The number in brackets indicates the power-on-reset default status of that bit.

7RS6RS5RS4RS3RS2RS1RS0RS

)0(YDR)0(0)0(0)0(0)0(RRE)0(0)0(YBTS)0(KCOL

Table VI. Status Register Bit Designations

Bit Bit Location Name Description

SR7 RDY Ready Bit for ADC.

Set when data is written to the ADC data register. The RDY bit is cleared automatically after the ADC data register has been read or a period of time before the data register is updated with a new conversion result.

SR6 0This bit is automatically cleared.

SR5 0This bit is automatically cleared.

SR4 0This bit is automatically cleared.

SR3 ERR ADC Error Bit. This bit is set at the same time as the RDY bit.

Set to indicate that the result written to the ADC data register has been clamped to all zeros or all ones. Error sources include Overrange, Underrange. Cleared by a write to the mode bits to initiate a conversion.

SR2 0This bit is automatically cleared.

SR1 STBY Standby Bit Indication.

When this bit is set, the AD7709 is in power-down mode. This bit is cleared when the ADC is powered up.

SR0 LOCK PLL Lock Status Bit.

Set if the PLL has locked onto the 32.768 kHz crystal oscillator clock. If the user is worried about exact sampling frequencies, etc., the LOCK bit should be interrogated and the result discarded if the LOCK bit is 0.

REV. A

–15–

Page 16

AD7709

Configuration Register (A1, A0 = 0, 1; Power-On-Reset = 000007H)

The Configuration Register is a 24-bit register from which data can either be read or to which data can be written. This register is used to select the input channel and configure the input range, excitation current sources, and I/O port. Table VII outlines the bit designations for this register. CONFIG23 to CONFIG0 indicate the bit location, CONFIG denoting the bits are in the Configuration Register. CONFIG23 denotes the first bit of the data stream. The number in brackets indicates the power-on-reset default status of that bit. A write to the Configuration Register has immediate effect and does not reset the ADC. Therefore, if a current source is switched while the ADC is converting, the user will have to wait for the full settling time of the sinc This equates to three outputs.

32GIFNOC32GIFNOC

32GIFNOC32GIFNOC22GIFNOC22GIFNOC

32GIFNOC

)0(2WSP)0(2WSP

)0(2WSP)0(2WSP)0(1WSP)0(1WSP

)0(2WSP

51GIFNOC41GIFNOC31GIFNOC21GIFNOC11GIFNOC01GIFNOC9GIFNOC8GIFNOC

)0(GID4P)0(GID3P)0(NE2P)0(NE1P)0(TAD4P)0(TAD3P)0(TAD2P)0(TAD1P

7GIFNOC7GIFNOC

7GIFNOC7GIFNOC6GIFNOC6GIFNOC

7GIFNOC

)0(LESFER)0(LESFER

)0(LESFER)0(LESFER)0(2HC)0(2HC

)0(LESFER

22GIFNOC22GIFNOC12GIFNOC12GIFNOC

22GIFNOC

)0(1WSP)0(1WSP)0(1NE3I)0(1NE3I

)0(1WSP

6GIFNOC6GIFNOC5GIFNOC5GIFNOC

6GIFNOC

)0(2HC)0(2HC)0(1HC)0(1HC

)0(2HC

12GIFNOC12GIFNOC02GIFNOC02GIFNOC

12GIFNOC

)0(1NE3I)0(1NE3I)0(0NE3I)0(0NE3I

)0(1NE3I

5GIFNOC5GIFNOC4GIFNOC4GIFNOC

5GIFNOC

)0(1HC)0(1HC)0(0HC)0(0HC

)0(1HC

Table VII. Configuration Register Bit Designations

02GIFNOC02GIFNOC91GIFNOC91GIFNOC

02GIFNOC

)0(0NE3I)0(0NE3I)0(1NE2I)0(1NE2I

)0(0NE3I

4GIFNOC4GIFNOC3GIFNOC3GIFNOC

4GIFNOC

)0(0HC)0(0HC)0(INU)1(2NR)1(1NR)1(0NR

)0(0HC

91GIFNOC91GIFNOC81GIFNOC81GIFNOC

91GIFNOC

)0(1NE2I)0(1NE2I)0(0NE2I)0(0NE2I

)0(1NE2I

3GIFNOC3GIFNOC2GIFNOC2GIFNOC

3GIFNOC

filter before obtaining a fully settled output.

81GIFNOC81GIFNOC71GIFNOC71GIFNOC

81GIFNOC

)0(0NE2I)0(0NE2I)0(1NE1I)0(1NE1I

)0(0NE2I

2GIFNOC2GIFNOC1GIFNOC1GIFNOC

2GIFNOC

71GIFNOC71GIFNOC61GIFNOC61GIFNOC

71GIFNOC

)0(1NE1I)0(1NE1I)0(0NE1I)0(0NE1I

)0(1NE1I

1GIFNOC1GIFNOC0GIFNOC0GIFNOC

1GIFNOC

61GIFNOC61GIFNOC

61GIFNOC

)0(0NE1I)0(0NE1I

)0(0NE1I

0GIFNOC0GIFNOC

0GIFNOC

Bit Bit Location Name Description

CONFIG23 PSW2 Power Switch 2 Control Bit.

Set by user to enable power switch SW2/P2 to PWRGND. Cleared by user to enable use as a standard I/O pin. When the ADC is in standby mode, the power switches are open.

CONFIG22 PSW1 Power Switch 1 Control Bit.

Set by user to enable power switch SW1/P1 to PWRGND. Cleared by user to enable use as a standard I/O pin. When the ADC is in standby mode, the power switches are open.

CONFIG21 I3EN1 IEXC3 Current Source Enable Bit

CONFIG20 I3EN0 IEXC3 Current Source Enable Bit

I3EN1 I3EN0 Function

00IEXC3 Current Source OFF 01IEXC3 Current Source Routed to the IOUT1 Pin 10IEXC3 Current Source Routed to the IOUT2 Pin 11Reserved

CONFIG19 I2EN1 IEXC2 Current Source Enable Bit

CONFIG18 I2EN0 IEXC2 Current Source Enable Bit

I2EN1 I2EN0 Function

00IEXC2 Current Source OFF 01IEXC2 Current Source Routed to the IOUT1 Pin 10IEXC2 Current Source Routed to the IOUT2 Pin 11Reserved

CONFIG17 I1EN1 IEXC1 Current Source Enable Bit

–16–

REV. A

Page 17

AD7709

Table VII. Configuration Register Bit Designations (continued)

Bit Bit Location Name Description

CONFIG16 I1EN0 IEXC1 Current Source Enable Bit

I1EN1 I1EN0 Function

00IEXC1 Current Source OFF 01IEXC1 Current Source Routed to the IOUT1 Pin 10IEXC1 Current Source Routed to the IOUT2 Pin 11Reserved

CONFIG15 P4DIG Digital Input Enable.

Set by user to enable pin AIN4/P4 as a digital input. A weak pull-up resistor is activated in this state. Cleared by user to configure pin AIN4/P4 as an analog input.

CONFIG14 P3DIG Digital Input Enable.

Set by user to enable pin AIN3/P3 as a digital input. A weak pull-up resistor is activated in this state. Cleared by user to configure pin AIN3/P3 as an analog input.

CONFIG13 P2EN SW2/P2 Digital Output Enable Bit.

Set by user to enable P2 as a regular digital output pin. Cleared by user to three-state the P2 output. PSW2 takes precedence over P2EN.

CONFIG12 P1EN SW1/P1 Digital Output Enable Bit.

Set by user to enable P1 as a regular digital output pin. Cleared by user to three-state the P1 output. PSW1 takes precedence over P1EN.

CONFIG11 P4DAT Digital Input Port Data Bit.

P4DAT is read only and will return a zero if P4DIG equals zero. If P4 is enabled as a digital input, the readback value indicates the status of pin P4.

CONFIG10 P3DAT Digital Input Port Data Bit.

P3DAT is read only and will return a zero if P3DIG equals zero. If P3 is enabled as a digital input, the readback value indicates the status of pin P3.

CONFIG9 P2DAT Digital Output Port Data Bit. P2 is a digital output only. When the port is active as an output (P2EN = 1),

the value written to this data bit appears at the output port. Reading P2DAT will return the last value written to the P2DAT bit.

CONFIG8 P1DAT Digital Output Port Data Bit. P1 is a digital output only. When the port is active as an output (P1EN = 1),

the value written to this data bit appears at the output port. Reading P1DAT will return the last value written to the P1DAT bit.

CONFIG7 REFSEL ADC Reference Input Select.

Cleared by the user to select REFIN1(+) and REFIN1(–) as the ADC reference. Set by the user to select REFIN2(+) and REFIN2(–) as the ADC reference.

CONFIG6 CH2 ADC Input Channel Selection Bit. It is used in conjunction with CH1 and CH0 as shown below.

CONFIG5 CH1 ADC Input Channel Selection Bit. It is used in conjunction with CH2 and CH0 as shown below.

CONFIG4 CH0 ADC Input Channel Selection Bit. It is used in conjunction with CH2 and CH1 as shown below.

CH2 CH1 CH0 Positive Input Negative Input Buffer

0 00AIN1 AINCOM Positive Analog Input 0 01AIN2 AINCOM Positive Analog Input 0 10AIN3 AINCOM Positive Analog Input 0 11AIN4 AINCOM Positive Analog Input 1 00AIN1 AIN2 Positive and Negative Analog Inputs 1 01AIN3 AIN4 Positive and Negative Analog Inputs 1 10AINCOM AINCOM None 1 11AIN2 AIN2 Positive and Negative Analog Inputs

The Buffer column indicates if the analog inputs are buffered or unbuffered. This determines the common-mode input range on each input. If the input is unbuffered (AINCOM), the common-mode input includes ground.

REV. A

–17–

Page 18

AD7709

Table VII. Configuration Register Bit Designations (continued)

Bit Bit Location Name Description

CONFIG3 UNI Unipolar/Bipolar Operation Selection Bit.

Set by the user to enable unipolar operation. In this mode, the device uses straight binary output coding i.e., 0 differential input will generate a result of 0000h and a full-scale differential input will generate a code of FFFFh. Cleared by the user to enable pseudo-bipolar operation. The device uses offset binary coding, i.e., a negative full-scale differential input will result in a code of 0000h, a 0 differential input will generate a code of 8000h, while a positive full-scale differential input will result in a code of FFFFh.

CONFIG2 RN2 This bit is used in conjunction with RN1 and RN0 to select the analog input range as shown below.

CONFIG1 RN1 This bit is used in conjunction with RN2 and RN0 to select the analog input range as shown below.

CONFIG0 RN0 This bit is used in conjunction with RN2 and RN1 to select the analog input range as shown below.

RN2 RN1 RN0 Selected ADC Input Range (V

00 0 ± 20 mV 00 1 ± 40 mV 01 0 ± 80 mV 01 1 ± 160 mV 10 0 ± 320 mV 10 1 ± 640 mV 11 0 ± 1.28 V 11 1 ± 2.56 V

= 2.5 V)

REF

Table VIII. Filter Register Bit Designations

7RF6RF5RF4RF3RF2RF1RF0RF

)0(7FS)1(6FS)0(5FS)0(4FS)0(3FS)1(2FS)0(1FS)1(0FS

Table IX. Update Rate vs. SF WORD

SF (Dec) SF (Hex) f

13 0D 105.3 9.52 69 45 19.79 50.34 255 FF 5.35 186.77

Filter Register (A1, A0 = 1, 0; Power-On-Reset = 45h)

The Filter Register is an 8-bit register from which data can be read or to which data can be written. This register determines the amount of averaging performed by the sinc filter. Table VIII outlines the bit designations for the Filter Register. FR7 through FR0 indicate the bit location, FR denoting the bits are in the Filter Register. FR7 denotes the first bit of the data stream. The number in brackets indicates the power-on/reset default status of that bit. The number in this register is used to set the decimation factor and thus the output update rate for the ADC. The Filter Register cannot be written to by the user while the ADC is active. The update rate is calculated as follows:

=¥

ADC MOD

318

where:

is the ADC output update rate.

ADC

is the Modulator Clock Frequency = 32.768 kHz.

MOD

SF is the decimal value written to the SF Register.

(Hz) t

ADC

(ms)

The allowable range for SF is 13dec to 255dec. Examples of SF values and corresponding conversion rate (f

ADC

) and time (t

ADC

) are shown in Table IX. It should also be noted that the ADC input channel is chopped to minimize offset errors. This means that the time for a single conversion or the time to the first conversion result is 2 ⫻ t

ADC Data Result Register (A1, A0 = 1, 1; Power-On-Reset = 0000h)

ADC

The conversion result is stored in the ADC Data Register (DATA). This register is 16-bits wide. This is a read-only register. On completion of a read from this register, the RDY bit in the Status Register is cleared.

–18–

REV. A

Page 19

AD7709

CONFIGURING THE AD7709

The four user-accessible registers on the AD7709 are accessed via the serial interface. Communication with any of these registers is initiated by first writing to the Communications Register. The AD7709 begins converting on power-up without the need to write to

the registers. The default conditions are used, i.e., the AD7709 operates at a 19.79 Hz update rate that offers 50 Hz and 60 Hz rejection.

Figure 10 outlines a flow diagram of the sequence used to configure all registers after a power-up or reset on the AD7709. The flowchart shows two methods of determining when it is valid to read the data register. The first method is hardware polling of the RDY pin and the second method involves software interrogation of the RDY bit in the status register. The flowchart details all the necessary programming steps required to initialize the ADC and read data from the ADC channel following a power-on or reset. The steps can be broken down as follows:

1. Configure and initialize the microcontroller or microproces-

sor serial port.

START

HARDWARE

POLLING

2. Initialize the AD7709 by configuring the following registers:

Filter Register to configure the update rate for the channel. The AD7709 must be placed in standby mode before the Filter Register can be written to.

b)Configuration Register to select the input channel to be

converted, its input range, and reference. This register is also

used to configure internal current sources, power switches, and I/O port.

Both of these operations consist of a write to the Communications Register to specify the next operation as a write to a specified register. Data is then written to this register. When each sequence is complete, the ADC defaults to waiting for another write to the Communications Register to specify the next operation.

3. When configuration is complete, the user needs to determine when it is valid to read the data from the data register. This is accomplished either by polling the RDY pin (hardware polling) or by interrogating the RDY bit in the STATUS register (software

polling). Both are shown in Figure 10.

SOFTWARE

POLLING

POWER-ON-RESET FOR AD7709

CONFIGURE AND INITIALIZE C/P SERIAL PORT

WRITE TO COMMUNICATIONS REGISTER SETTING

UP NEXT OPERATION TO BE A WRITE TO THE FILTER REGISTER (WRITE 22H TO REGISTER)

WRITE TO FILTER REGISTER CONFIRMING

THE REQUIRED UPDATE RATE

WRITE TO COMMUNICATIONS REGISTER SETTING

UP NEXT OPERATION TO BE A WRITE TO THE

CONFIGURATION REGISTER

(WRITE 01H TO REGISTER)

WRITE TO CONFIGURATION REGISTER TO SELECT

THE INPUT CHANNEL, INPUT RANGE, AND

REFERENCE. CURRENT SOURCES AND I/O PORT

CAN ALSO BE CONFIGURED

READ DATA FROM OUTPUT REGISTER

HARDWARE

POLLING

SOFTWARE

POLLING

POLL RDY PIN

WRITE TO COMMUNICATIONS REGISTER SETTING

UP NEXT OPERATION TO BE A READ FROM THE

DATA REGISTER (WRITE 43H TO REGISTER)

READ 16-BIT DATA RESULT

YES

RDY

LOW?

YES

ANOTHER

READ

CHANNEL

CHANGE

END

YES

WRITE TO COMMUNICATIONS REGISTER SETTING

UP NEXT OPERATION TO BE A READ FROM THE

STATUS REGISTER (WRITE 40H TO REGISTER)

READ STATUS REGISTER

RDY = 1

YES

WRITE TO COMMUNICATIONS REGISTER SETTING

UP NEXT OPERATION TO BE A READ FROM THE

DATA REGISTER (WRITE 43H TO REGISTER)

READ 16-BIT DATA RESULT

YES

ANOTHER

READ

CHANNEL

CHANGE

REV. A

END

Figure 10. Flowchart for Initializing and Reading Data from the AD7709

–19–

Page 20

AD7709

DIGITAL INTERFACE

As previously outlined, AD7709 programmable functions are controlled using a set of on-chip registers. Data is written to these registers via the part’s serial interface and read access to the on-chip registers is also provided by this interface. All communications to the part must start with a write operation to the

reset

Communications Register. After power-on or expects a write to its Communications Register. The data written to this register determines whether the next operation to the part is a read or a write operation and also determines to which register this read or write operation occurs. Therefore, write access to any of the other registers on the part starts with a write operation to the Communications Register followed by a write to the selected register. A read operation from any other register on the part (including the output data register) starts with a write operation to the Communications Register followed by a read operation from the selected register.

The AD7709 serial interface consists of five signals: CS, SCLK, DIN, DOUT, and RDY. The DIN line is used for transferring data into the on-chip registers, while the DOUT line is used for accessing data from the on-chip registers. SCLK is the serial clock input for the device, and all data transfers (either on DIN or DOUT) take place with respect to this SCLK signal. The RDY line is used as a status signal to indicate when data is ready to be read from the AD7709 data register. RDY goes low when a new data-word is available in the output register. It is reset high when a read operation from the data register is complete. It also goes high prior to the updating when not to read from the device attempted while the register is being updated. CS is used to select the device. It can be used to decode the AD7709 in systems where a number of parts are connected to the serial bus.

Figures 2 and 3 show timing diagrams for interfacing to the AD7709 with CS used to decode the part. Figure 3 is for a read operation from the AD7709 output shift register while Figure 2 shows a write operation to the input shift register. It is possible to read the same data twice from the output register even though the RDY line returns high after the first read operation. Care must be taken, however, to ensure that the read operations have been completed before the next output update is about to take place.

The AD7709 serial interface can operate in 3-wire mode by tying the CS input low. In this case, the SCLK, DIN, and DOUT lines are used to communicate with the AD7709, and the status of the RDY bit can be obtained by interrogating the Status Register. This scheme is suitable for interfacing to microcontrollers. If CS is required as a decoding signal, it can be generated from a port bit. For microcontroller interfaces, it is recommended that the SCLK idles high between data transfers.

The AD7709 can also be operated with CS used as a frame synchronization signal. This scheme is suitable for DSP interfaces. In this case, the first bit (MSB) is effectively clocked out by CS since CS would normally occur after the falling edge of SCLK in DSPs. The SCLK can continue to run between data transfers provided the timing numbers are obeyed.

of the output register to indicate

to ensure that a data read is not

, the device

The serial interface can be reset by exercising the RESET input on the part. It can also be reset by writing a series of 1s on the DIN input. If a Logic 1 is written to the AD7709 DIN line for at least 32 serial clock cycles, the serial interface is reset. This ensures that in 3-wire systems, if the interface gets lost either via a software error or by some glitch in the system, it can be reset back to a known state. This state returns the interface to where the AD7709 is expecting a write operation to its Communications Register. This operation resets the contents of all registers to their power-on reset values.

Some microprocessor or microcontroller serial interfaces have a single serial data line. In this case, it is possible to connect the AD7709 DOUT and DIN lines together and connect them to the single data line of the processor. A 10 kW pull-up resistor should be used on this single data line. In this case, if the interface gets lost, because the read and write operations share the same line, the procedure to reset it back to a known state is somewhat different than previously described. It requires a read operation of 24 serial clocks followed by a write operation where a Logic 1 is written for at least 32 serial clock cycles to ensure that the serial interface is back into a known state.

MICROCOMPUTER/MICROPROCESSOR INTERFACING

The AD7709 flexible serial interface allows for easy interface to most microcomputers and microprocessors. The flowchart of Figure 10 outlines the sequence that should be followed when interfacing a microcontroller or microprocessor to the AD7709. Figures 11, 12, and 13 show some typical interface circuits. The serial interface on the AD7709 is capable of operating from just three wires and is compatible with SPI interface protocols. The 3-wire operation makes the part ideal for isolated systems where minimizing the number of interface lines minimizes the number of opto-isolators required in the system. The serial clock input is a Schmitt-triggered input to accommodate slow edges from opto-couplers. The rise and fall times of other digital inputs to the AD7709 should be no longer than 1 ms.

Some of the registers on the AD7709 are 8-bit registers, which facilitates easy interfacing to the 8-bit serial ports of microcontrollers. The Data Register on the AD7709 is 16 bits and the Configuration Register is 24 bits, but data transfers to these registers can consist of multiple 8-bit transfers to the serial port of the microcontroller. DSP processors and microprocessors generally transfer 16 bits of data in a serial data operation. Some of these processors, such as the ADSP-2105, have the facility to program the amount of cycles in a serial transfer. This allows the user to tailor the number of bits in any transfer to match the register length of the required register in the AD7709.

Even though some of the registers on the AD7709 are only 8 bits in length, communicating with two of these registers in successive write operations can be handled as a single 16-bit data transfer if required. For example, if the Filter Register is to be updated, the processor must first write to the Communications Register (saying that the next operation is a write to the Filter Register), and then write 8 bits to the Filter Register. If required, this can all be done in a single 16-bit transfer because once the eight serial clocks of the write operation to the Communications Register have been completed, the part immediately sets itself up for a write operation to the Filter Register.

–20–

REV. A

Page 21

AD7709

AD7709-to-68HC11 Interface

Figure 11 shows an interface between the AD7709 and the 68HC11 microcontroller. The diagram shows the minimum (3-wire) interface with CS on the AD7709 hardwired low. In this scheme, the RDY bit of the Status Register is monitored to determine when the Data Register is updated. An alternative scheme, which increases the number of interface lines to four, is to monitor the RDY output line from the AD7709. The monitoring of the RDY line can be done in two ways. First, RDY can be connected to one of the 68HC11 port bits (such as PC0), which is configured as an input. This port bit is then polled to determine the status of RDY. The second scheme is to use an interrupt driven system, in which case the RDY output is connected to the IRQ input of the 68HC11. For interfaces that require control of the CS input on the AD7709, one of the port bits of the 68HC11 (such as PC1), which is configured as an output, can be used to drive the CS input.

The 68HC11 is configured in the master mode with its CPOL bit set to a Logic 1 and its CPHA bit set to a Logic 1. When the 68HC11 is configured like this, its SCLK line idles high between data transfers. The AD7709 is not capable of full-duplex operation. If the AD7709 is configured for a write operation, no data appears on the DOUT lines even when the SCLK input is active. Similarly, if the AD7709 is configured for a read operation, data presented to the part on the DIN line is ignored even when SCLK is active.

68HC11

SCK

MISO

AD7709

RESET

SCLK

DOUT

MOSI

DIN

8XC51

P3.0

P3.1

10k

AD7709

RESET

DOUT

DIN

SCLK

Figure 12. AD7709-to-8XC51 Interface

The second scheme is to use an interrupt-driven system, in which case the RDY output is connected to the INT1 input of the 8XC51. For interfaces that require control of the CS input on the AD7709, one of the port bits of the 8XC51 (such as P1.1), which is configured as an output, can be used to drive the CS input. The 8XC51 is configured in its Mode 0 serial interface mode. Its serial interface contains a single data line. As a result, the DOUT and DIN pins of the AD7709 should be connected together with a 10 kW pull-up resistor. The serial clock on the 8XC51 idles high between data transfers. The 8XC51 outputs the LSB first in a write operation, while the AD7709 expects the MSB first so the data to be transmitted has to be rearranged before being written to the output serial register. Similarly, the AD7709 outputs the MSB first during a read operation while the 8XC51 expects the LSB first. Therefore, the data read into the serial buffer needs to be rearranged before the correct data word from the AD7709 is available in the accumulator.

ADSP-2103/

ADSP-2105

RFS

TFS

AD7709

RESET

Figure 11. AD7709-to-68HC11 Interface

AD7709-to-8051 Interface

An interface circuit between the AD7709 and the 8XC51 microcontroller is shown in Figure 12. The diagram shows the minimum number of interface connections with CS on the AD7709 hardwired low. In the case of the 8XC51 interface, the minimum number of interconnects is just two. In this scheme, the RDY bit of the Status Register is monitored to determine when the Data Register is updated. The alternative scheme, which increases the number of interface lines to three, is to monitor the RDY output line from the AD7709. The monitoring of the RDY line can be done in two ways. First, RDY can be connected to one of the 8XC51 port bits (such as P1.0) which is configured as an input. This port bit is then polled to determine the status of RDY.

REV. A

–21–

SCLK

DOUT

DIN

SCLK

Figure 13. AD7709-to-ADSP-2103/ADSP-2105 Interface

AD7709-to-ADSP-2103/ADSP-2105 Interface

Figure 13 shows an interface between the AD7709 and the ADSP-2103/ADSP-2105 DSP processor. In the interface shown, the RDY bit of the Status Register is again monitored to determine when the Data Register is updated. The alternative scheme is to use an interrupt-driven system, in which case the

Page 22

IOUT1

AIN3/P3

AINCOM

AIN1

IOUT2

AIN4/P4

REFIN1(–)

AIN2

REFIN1(+)

REFIN2(–)

REFIN2(+)

RESET

DOUT

DIN

SCLK

P2/SW2

P1/SW1

XTAL1

XTAL2

CHIP SELECT

RECEIVE (READ)

SERIAL CLOCK

32.768kHz CRYSTAL

PWRGND

GND

AD780/

REF195

VINV

OUT

GND

ANALOG 5V

SUPPLY

0.1F

10F

0.1F

10F

ANALOG 5V

SUPPLY

AD7709

SERIAL DATA (WRITE)

AD7709

RDY output is connected to the IRQ2 input of the ADSP-2103/ ADSP-2105. The serial interface of the ADSP-2103/ADSP-2105 is set up for alternate framing mode. The RFS and TFS pins of the ADSP-2103/ADSP-2105 are configured as active low outputs and the ADSP-2103/ADSP-2105 serial clock line, SCLK, is also configured as an output. The CS for the AD7709 is active when either the RFS or TFS outputs from the ADSP-2103/ ADSP-2105 are active. The serial clock rate on the ADSP-2103/ ADSP-2105 should be limited to 3 MHz to ensure correct operation with the AD7709.

CIRCUIT DESCRIPTION

The AD7709 is a ⌺-⌬ A/D converter with on-chip digital filtering, intended for the measurement of wide dynamic range, low frequency signals such as those in weigh scale, pressure, temperature, industrial control, or process control applications. It employs a ⌺-⌬ conversion technique to realize up to 16 bits of no-missingcodes performance. The ⌺-⌬ modulator converts the sampled input signal into a digital pulse train whose duty cycle contains the digital information. A Sinc then employed to decimate the modulator output data stream to give a valid data conversion result at programmable output rates from 5.35 Hz (186.77 ms) to 105.03 Hz (9.52 ms). A chopping scheme is also employed to minimize ADC offset and offset and gain drift errors. The channel is buffered and can be programmed for one of eight input ranges from ± 20 mV to ±2.56 V. The input channels can be configured for either fully differential inputs or pseudo-differential input channels via the CH2, CH1, and CH0 bits in the Configuration Register. Buffering the input channel allows the part to handle significant source impedances on the analog input, allowing R/C filtering (for noise rejection or RFI reduction) to be placed on the analog inputs if required. These input channels are intended for converting signals directly from sensors without the need for external signal conditioning. Other functions contained on-chip that augment the operation of the ADC include software configurable current sources, switchable reference inputs, and low-side power switches.

The basic connection diagram for the AD7709 is shown in Figure 14. An AD780/REF195, precision 2.5 V reference, provides the reference source for the part. A quartz crystal or ceramic resonator provides the 32.768 kHz master clock source for the part. In some cases, it will be necessary to connect capacitors on the crystal or resonator to ensure that it does not oscillate at overtones capacitors will vary depending on manufacturer specifications.

Analog Input Channels

The main ADC has five associated analog input pins (labeled AIN1 to AIN4 and AINCOM) that can be configured as two fully differential input channels (AIN1–AIN2 and AIN3–AIN4) or four pseudo-differential input channels (AIN1–AINCOM, AIN2–AINCOM, AIN3–AINCOM, and AIN4–AINCOM). Channel selection bits CH2, CHI, and CH0 in the Configuration Register detail the different configurations. When the analog channel is switched, the settling time of the part must elapse before a new valid word is available from the ADC.

of its fundamental operating frequency. The values of

programmable low-pass filter is

The output of the ADC multiplexer feeds into a high impedance input stage of the buffer amplifier. As a result, the ADC inputs can handle significant source impedances and are tailored for direct connection to external resistive-type sensors like strain gauges or Resistance Temperature Detectors (RTDs).

The absolute input voltage range on the ADC inputs when buffered (AIN1 to AIN4) is restricted to a range between GND + 100 mV and V the common-mode voltage and input voltage range so that these limits are not exceeded; otherwise, there will be a degradation in linearity and noise performance.

The absolute input voltage range on the ADC inputs when unbuffered (AINCOM) includes the range between GND – 30 mV V lute input voltage limit does allow the possibility of monitoring small true bipolar signals with respect to GND.

input

Figure 14. Basic Connection Diagram

– 100 mV. Care must be taken in setting up

+ 30 mV as a result of being unbuffered. The negative abso-

–22–

REV. A

Page 23

Programmable Gain Amplifier

AIN3AIN3

AIN4AIN4

AIN1/AINCOM

PSEUDO-DIFFERENTIAL

INPUT

AIN(–)

AIN(+)

AIN1

AIN2

AINCOM

ADC CHANNEL

MUX

AIN2/AINCOM

AIN3/AINCOM

AIN4/AINCOM

PSEUDO-DIFFERENTIAL

INPUT

The output from the buffer on the ADC is applied to the input of the on-chip programmable gain amplifier (PGA). The PGA can be programmed through eight different unipolar and bipolar

FULLY DIFFERENTIAL

ranges. The PGA gain range is programmed via the range bits in the Configuration Register. With an external 2.5 V reference applied, the unipolar ranges are 0 mV to 20 mV, 0 mV to 40 mV, 0 mV

to 80 mV, 0 mV to 160 mV, 0 mV to 320

640 mV, 0 V are ±20 mV, mV, ±1.28 V, and

to 1.28 V, and 0 to 2.56 V, while bipolar ranges

±40 mV, ± 80 mV, ±160 mV, ±320 mV, ±640

±2.56 V.

These are the ranges that should

, 0 mV to

FULLY DIFFERENTIAL

appear at the input to the on-chip PGA.

Typical matching across ranges is shown in Figure 15. Here, the ADC is configured in fully differential, bipolar mode with an external 2.5 V reference, while an analog input voltage of just greater than 19 mV is forced on its analog inputs. The ADC continuously converts the dc voltage at an update rate of 5.35 Hz, i.e., SF = FFh. A total of 800 conversion results are gathered. The first 100 results gathered with the ADC operating in the ±20 mV. The ADC range is then switched to ±40 mV and 100 more results are gathered, and so on, until the last 100 samples are gathered with the ADC configured in the ±2.5 V range. From Figure 15, the variation in the sample mean through each range, i.e., the range matching, is seen to be on the order of 2 µV.

AD7709

MUX

AIN1

AIN2

AIN3

AIN4

Figure 16. Fully Differential Mode of Operation

AIN1

AIN(+)

AIN2

ADC CHANNEL

AIN3

AIN(–)

AIN4

19.372

19.371

19.370

19.369

19.368

19.367

19.366

ADC INPUT VOLTAGE – mV

19.365

19.364

SAMPLE COUNT

ADC RANGE

0 100 200 300 400 500 600 700 800

ⴞ40mV

ⴞ20mV

ⴞ80mV

ⴞ160mV

ⴞ320mV

ⴞ640mV

Figure 15. ADC Range Matching

Bipolar/Unipolar Configuration

The analog inputs on the AD7709 can accept either unipolar or bipolar input voltage ranges. Bipolar input ranges do not imply that the part can handle negative voltages with respect to system GND. Unipolar and bipolar signals on the AIN(+) input on

ADC are referenced to the voltage on the respective AIN(–)

the input. AIN(+) and AIN(–) refer to the signals seen by the modulator that come from the output of the multiplexer, as in Figures 16 and 17.

REV. A

ⴞ1.28V

ⴞ2.56V

shown

Figure 17. Pseudo-Differential Mode of Operation

For example, if AIN(–) is 2.5 V and the ADC is configured for an analog input range of 0 mV to 20 mV, the input voltage range on the AIN(+) input is 2.5 V to 2.52 V. If AIN(–) is 2.5 V and the AD7709 is configured for an analog input range of ±1.28 V, the analog input range on the AIN(+) input is 1.22 V to 3.78 V (i.e., 2.5 V ±1.28 V). Bipolar or unipolar options are chosen by programming the UNI bit in the Configuration Register. This programs the ADC for either unipolar or bipolar operation. Programming for either unipolar or bipolar operation does not change any of the input signal conditioning; it simply changes the data output coding.

Data Output Coding

When the ADC is configured for unipolar operation, the output coding is natural (straight) binary with a zero differential input voltage resulting in a code of 000 . . . 000, a midscale voltage resulting in a code of 100 . . . 000, and a full-scale input voltage resulting in a code of 111 . . . 111. The output code for any analog input voltage on the ADC can be represented as follows:

REF

Code

AIN GAIN

××

()

1 024.

()

where:

AIN is the analog input voltage.

GAIN is the PGA gain, i.e., 1 on the 2.56 V range and 128 on

the 20 mV range.

N = 16.

–23–

Page 24

AD7709

When the ADC is configured for bipolar operation, the coding is offset binary with a negative full-scale voltage resulting in a code of 000 . . . 000, a zero differential voltage resulting in a code of 100 . . . 000, and a positive full-scale voltage resulting in a code of 111 . . . 111. The output code from the ADC for any analog input voltage can be represented as follows:

Code AIN GAIN V

=¥ ¥ ¥

21024 1

()

[]

()

REF

where:

AIN is the analog input voltage. GAIN in the PGA gain, i.e., 1 on the ± 2.56 V range and 128

on the ± 20 mV range.

N = 16.

Excitation Currents

The AD7709 also contains three software configurable constant current sources. IEXC1 and IEXC2 provide 200 mA of current while IEXC3 provides 25 mA of current. All source current from V

is directed to either the IOUT1 or IOUT2 pins of the

device. These current sources are controlled via bits in the Configuration Register. The configuration bits enable the current sources, and they can be configured to source current individually to both pins or a combination of currents, i.e., 400 mA, 225 mA, or 425 mA to either of the selected output pins. These current sources can be used to excite external resistive bridge or RTD sensors.

Crystal Oscillator

The AD7709 is intended for use with a 32.768 kHz watch crystal. A PLL internally locks onto a multiple of this frequency to provide a stable 4.194304 MHz clock for the ADC. The modulator sample rate is the same as the crystal oscillator frequency.

The start-up time associated with 32.768 kHz crystals is typically 300 ms. The OSCPD bit in the Communications Register can be used to prevent the oscillator from powering down when the AD7709 is placed in power-down mode. This avoids having to wait 300 ms after exiting power-down to start a conversion at the expense of raising the power-down current.

Reference Input

The AD7709 has a fully differential reference input capability for the channel. On the channel, the reference inputs can be REFIN1(+) and REFIN1(–) or REFIN2(+) and REFIN2(–). They provide a differential reference input capability. The common-mode range for these differential inputs is from GND

. The reference input is unbuffered and therefore

to V

excessive R-C source impedances will introduce gain errors. The nominal reference voltage, V

, ((REFIN1(+)

REF

– REFIN1(–) or (REFIN2(+) – REFIN2(–)), for specified operation is 2.5 V, but the AD7709 is functional with reference voltages from 1 V to V

. In applications where the excitation

(voltage or current) for the transducer on the analog input also drives the reference voltage for the part, the effect of the low frequency noise in the excitation source will be removed

because the application is ratiometric. If the AD7709 is used in a nonratiometric application, a low noise reference should be used. Recommended reference voltage sources for the AD7709 include the AD780, REF43, and REF192. It should also be noted that the reference inputs provide a high impedance, dynamic load. Because the input impedance of each reference input is dynamic, resistor/capacitor combinations on these inputs can cause dc gain errors, depending on the driving the reference inputs. recommended above (e.g., impedances and are therefore tors on the REFIN(+) Deriving the reference input

output impedance of the source that is

Reference voltage sources like those

AD780) will typically have low output

tolerant to having decoupling capaci-

without

introducing gain errors in the system.

voltage across an external resistor, as shown in Figure 18, will mean that the reference input sees a significant external source impedance. REFIN pins would not be recommended

External decoupling on the

in this type of circuit

configuration.

Reset Input

The RESET input on the AD7709 resets all the logic, the digital filter, and the analog modulator while all on-chip registers are reset to their default state. RDY is driven high and the AD7709 ignores all communications to any of its registers while the RESET input is low. When the RESET input returns high, the AD7709 operates with its default setup conditions and it is necessary to set up all registers after a RESET command.

Power-Down Mode

Loading 0 to the STBY bit in the ADC Communications Register places the AD7709 in device power-down mode. The AD7709 retains the contents of all its on-chip registers (including the data register) while in power-down mode.

The device power-down mode does not affect the digital interface, but it does affect the status of the RDY pin. Putting the AD7709 into power-down mode will reset the RDY line high. Placing the part in power-down mode reduces the total current to 26 mA typical when the part is operated at 5 V with the oscillator running during power-down mode. With the oscillator shut down, the total

is 1.5 mA typical at 3 V and 6.5 mA typical at 5 V.

Grounding and Layout

Since the analog inputs and reference inputs on the ADC are differential, most of the voltages in the analog modulator are common-mode voltages. The excellent common-mode rejection of the part will remove common-mode noise on these inputs. The digital filter will provide rejection of broadband noise on the power supply, except at integer multiples of the modulator sampling frequency. The digital filter also removes noise from the analog and reference inputs, provided these noise sources do not saturate the analog modulator. As a result, the AD7709 is more immune to noise interference than a conventional high resolution converter. However, because the resolution of the AD7709 is so high, and the noise levels from the AD7709 so low, care must be taken with regard to grounding and layout.

–24–

REV. A

Page 25

AD7709

The printed circuit board that houses the AD7709 should be designed such that the analog and digital sections are separated and confined to certain areas of the board. A minimum etch technique is generally best for ground planes as it gives the best shielding.

It is recommended that the AD7709 GND pin be tied to the AGND plane of the system. In any layout, it is important that the user keep in mind the flow of currents in the system ensuring that the return paths for all currents are as close as possible to the paths the currents took to reach their destinations. Avoid forcing digital currents to flow through the AGND sections of the layout.

The PWRGND pin is tied internally to GND on the AD7709. The PWRGND pad internally has a resistance of less than 50 mW to the PWRGND pin, while the resistance back to the GND pad is less than 3 W. This means that 19.5 mA of the maximum specified current (20 mA) will flow to PWRGND with the remaining

0.5 mA flowing to GND. PWRGND and GND should be tied together at the AD7709, and it is important to minimize the resistance on the ground return lines.

Avoid running digital lines under the device since these will couple noise onto the die. The analog ground plane should be allowed to run under the AD7709 to prevent noise coupling. The power supply lines to the AD7709 should use as wide a trace as possible to provide low impedance paths and reduce the effects of glitches on the power supply line. Fast switching signals like clocks should be shielded with digital ground to avoid radiating noise to other sections of the board, and clock signals should never be run near the analog inputs. Avoid crossover of digital and analog signals. Traces on opposite sides of the board should run at right angles to each other, which will reduce the effects of feedthrough through the board. A microstrip technique is by far the best, but is not always possible with a double-sided board. In this technique, the component side of the board is dedicated to ground planes while signals are placed on the solder side.

Good decoupling is important when using high resolution ADCs. The supply should be decoupled with 10 mF tantalum in parallel with 0.1 mF capacitors to GND. To achieve the best from these decoupling components, they have to be placed as close as possible; chips should be decoupled with 0.1 mF ceramic capacitors to DGND.

APPLICATIONS

The AD7709 provides a low cost, high resolution, analog-to-digital function. Because the analog-to-digital function is provided by a ⌺-⌬ architecture, it makes the part more immune to noisy environments, making it ideal for use in sensor measurement and industrial and process control applications. Given the architecture used in the AD7709, where the signal chain is chopped and the device is factory-calibrated at final test, field calibration is not needed due to the extremely low offset and gain drifts exhibited by this converter. It also provides a programmable gain amplifier and a digital filter. Thus, it provides far more system-level functionality than off-the-shelf integrating ADCs without the disadvantage of having to supply a high quality integrating capacitor. In addition, using the AD7709 in a system

allows the

system designer to achieve a much higher level of reso noise performance of the AD7709 is significantly

lution because

better than that

of integrating ADCs.

The on-chip PGA allows the AD7709 to handle an analog input voltage range as low as 10 mV full scale with V

= 1.25 V. The

REF

differential inputs of the part allow this analog input range to have an absolute value anywhere between GND + 100 mV and

– 100 mV. It allows the user to connect the transducer

directly to the input of the AD7709. The programmable gain front end on the AD7709 allows the part to handle unipolar analog input ranges from 0 mV to 20 mV and 0 V to 2.5 V and bipolar inputs of ± 20 mV to ± 2.5 V. Because the part operates from a single supply, these bipolar ranges are with respect to a biased-up differential input.

Pressure Measurement

One typical application of the AD7709 is pressure measurement. Figure 18 shows the AD7709 used with a pressure transducer, the BP01 from Sensym. The pressure transducer is arranged in a bridge network and gives a differential output voltage between its OUT(+) and OUT(–) terminals. With rated full-scale pressure (in this case 300 mmHg) on the transducer, the differential output voltage is 3 mV/V of the input voltage (i.e., the voltage between its IN(+) and IN(–) terminals).

Assuming a 5 V excitation voltage, the full-scale output range from the transducer is 15 mV. The excitation voltage for the bridge can be used to directly provide the reference for the ADC as the reference input range includes the supply. Alternatively, a suitable resistor divider can be implemented that allows the full dynamic range of the input to be utilized in this application. This implementation is fully ratiometric, so variations in the excitation voltage do not introduce errors in the system. Choosing resistor values of 10 kW and 6 kW as per Figure 18 gives a 1.875 V reference voltage for the AD7709 when the excitation voltage is 5 V.

EXCITATION VOLTAGE = 5V

IN+

OUT–

IN–

OUT+

10k

6k

AIN1

AIN2

REFIN1(+)

REFIN2(–)

GND

AD7709

PWRGND

Figure 18. Pressure Measurement Using the AD7709

Using the part with a programmed gain of 128 results in the full-scale input span of the AD7709 being 15 mV, which corresponds with the output span from the transducer.

REV. A

–25–

Page 26

AD7709

A second key advantage to using the AD7709 in transducer-based applications is that the on-chip low-side power switch can be fully utilized in low power applications. The low-side power switch is connected in series with the cold side of the bridge. In normal

Temperature Measurement

The AD7709 is also useful in temperature measurement applications. Figure 20 shows an RTD temperature measurement application.

operation, the switch is closed and measurements can be taken from the bridge. In applications where power is a concern, the AD7709 can be put into low power mode, substantially reducing the power burned in the application. In addition to this, the power switch can be opened while in low power mode, thus avoiding the unnecessary burning of power in the front end transducer. When taken back out of power-down, and the power switch is closed, the user should ensure that the front end circuitry is fully settled before attempting a read from the AD7709.

The circuit in Figure 19 shows a method that utilizes three pseudo-differential input channels on the AD7709 to temperaturecompensate a pressure transducer.

REFIN(+)

REFIN(–)

AIN2

AD7709

AIN1

AINCOM

AIN3

GND

In this application, the transducer is an RTD (Resistive Temperature Device), a PT100. The arrangement is a 4-lead RTD configuration. There are voltage drops across the lead resistances RL1 and RL4, but these simply shift the common-mode voltage.

XTAL1

There is no voltage drop across lead resistances RL2 and RL3 since the input current to the AD7709 is very low, looking into a high input impedance buffer. R

XTAL2

input voltage to ensure that it lies within the common-mode range (GND + 100 mV to V application shown, the on-chip 200 mA current source provides the excitation current for the PT100 and also generates the reference

OUT(–)

PRESSURE

BRIDGE

IOUT1

6.25k

IN(+)

OUT(+)

IN(–)

250

voltage for the AD7709 via the 6.25 kW resistor. Variations in the excitation current do not affect the circuit since both the

Figure 19. Temperature-Compensating a Pressure Transducer

In this application, pseudo-differential input channel AIN1/ AINCOM is used to measure the bridge output while pseuo-

input excitation temperature coefficient to avoid errors in the reference over temperature.

differential channels AIN2/AINCOM and AIN3/AINCOM measure the voltage across the bridge. The voltage measured across the bridge will vary proportionally with temperature, and the delta in this voltage can be used to temperaturecompensate the output of the pressure bridge.

200A

XTAL1

XTAL2

DRDY

SCLK

DIN

DOUT

CONTROLLER

RL1

RL2

RL4

RL3

RTD

REF

6.25k

AD7709

REFIN(–)

REFIN(+)

IOUT1

IOUT2

AIN1

AIN2

GND PWRGND

Figure 20. 4-Wire RTD Temperature Measurement Using the AD7709

is included to shift the analog

– 100 mV) of the ADC. In the

voltage and the reference voltage vary ratiometrically with the

current. However, the 6.25 kW resistor must

have a low voltage

–26–

REV. A

Page 27

AD7709

Figure 21 shows a further enhancement to the circuit shown in Figure 20. Generally, dc excitation has been accepted as the normal method of exciting resistive based sensors like RTDs in temperature measurement applications.

3-Wire RTD Configurations

To fully optimize a 3-wire RTD configuration, two identically matched current sources are required. The AD7709, which contains two well matched 200 mA current sources, is ideally suited to these applications. One possible 3-wire configuration

MUX1

200A

AD7709

BUF AND PGA

RESISTIVE

RANSDUCER

EMF1

EMF2

A A

REF

IOUT1

IOUT2

AIN1

AIN2

AIN3

AIN4

REFIN(+)

REFIN(–)

Figure 21. Low Resistance Measurement

With dc excitation, the excitation current through the sensor must be large enough so that the smallest temperature/resis-

using the AD7709 is shown in Figure 22.

IOUT1

REFIN(+)

6.25k

RL1

RTD

RL2

RL3

REFIN(–)

AIN1

AIN2

IOUT2

GND

200A

AD7709

XTAL1

XTAL2

DRDY

SCLK

DIN

DOUT

CONTROLLER

tance change to be measured results in a voltage change that is larger than the system noise, offset, and drift of the system. The purpose of switching the excitation source is to eliminate dc-induced errors. DC errors (EMF1 and EMF2) due to parasitic thermocouples produced by differential metal connections (solder and copper track) within the circuit are also eliminated when using this switching arrangement. This excitation is a form of synchronous detection where the sensor is excited with an alternating excitation source and the ADC measures information only in the same phase as the excitation source.

The switched polarity current source is developed using the on-chip current sources and external phase control switches (A and A) driven by AD7709 logic outputs P1 and P2. During the conversion process, the AD7709 takes two conversion results, one on each phase. During Phase 1, the on-chip current source is directed to IOUT1 and flows top to bottom through the sensor and switch controlled by A. In Phase 2, the current source is directed to IOUT2 the sensor and through

and flows in the opposite direction through

switch controlled by A. In all cases, the

current flows in the same direction through the reference resistor to develop the reference voltage for the ADC. All measurements are ratiometrically derived. The results of both conversions are combined within the microcontroller to produce one output measurement representing the resistance or temperature of the transducer. For example, if the RTD output during Phase 1 is 10 mV, a 1 mV circuit-induced dc error exists due to parasitic thermocouples, the ADC measures 11 mV. During the second phase, the excitation current is reversed and the ADC measures –10 mV from the RTD and again sees 1 mV dc error, giving an ADC output of –9 mV during this phase. These measurements are processed in the controller (11 mV – (–9 mV)/2 = 10 mV), thus removing the dc-induced errors within the system.

Figure 22. 3-Wire RTD Configuration Using the AD7709

In this 3-wire configuration, the lead resistances will result in errors if only one current source is used since the 200 mA will flow through RL1, developing a voltage error between AIN1 and AIN2. In the scheme outlined below, the second RTD current source is used to compensate for the error introduced by the 200 mA flowing through RL1. The second RTD current flows through RL2. Assuming that RL1 and RL2 are equal (the leads would normally be of the same material and of equal length) and that IOUT1 and IOUT2 match, the error voltage across RL2 equals the error voltage across RL1 and no error voltage is between AIN1 and AIN2. Twice the voltage is developed but, since this is a common-mode voltage, it will not errors. R combination of RL3 and R

is included so the current flowing through the

develops enough voltage that the

analog input voltage seen by the AD7709 is within the common

developed

across RL3

introduce

mode range of the ADC. The reference voltage for the AD7709 is also generated using one of these matched current sources.

This reference voltage is developed across the 6.25 kW resistor as

shown, and applied to the differential reference inputs of the

AD7709.

This scheme ensures that the analog input voltage span remains ratiometric to the reference voltage. Any errors in the analog input voltage due to the temperature drift of the RTD current

source is compensated for by the variation in the reference

voltage.

The typical drift matching between the two RTD current sources is less than 20 ppm/∞C. The voltage on either I can go to within 0.6 V of the V

supply.

OUT

The AD7709 also includes a 25 mA current source that can be used along with the two 200 mA current sources for VBE measurement where a 17:1 ratio is required from the current sources.

In the circuit shown in Figure 20, the resistance measurement is made using ratiometric techniques. Resistor R

, which develops

REF

the ADC reference, must be stable over temperature to prevent reference-induced errors in the measurement output.

REV. A

–27–

Page 28

AD7709

Smart Transmitters

Smart transmitters are another key design-in area for the AD7709. The ⌺-⌬ converter, single-supply operation, 3-wire interface capabilities, and small package size are all of benefit in smart transmitters. Here, the entire smart transmitter must operate from the 4–20 mA loop. Tolerances in the loop mean that the

10␮F

VARIABLES

0.1␮F

AIN1

AIN2

AIN3

AIN4

AD7709

GND

REFIN(+)

REFIN(–)

DOUT

SCLK

DIN

0.1␮F

MICROCONTROLLER

GND

amount of current available to power the transmitter is as low

3.5 mA. Figure 23 shows a block diagram of a smart transmitter that includes the AD7709.

Not shown in Figure 23 is the isolated power source required to power the front end.

DN25D

4.7␮F

3.3V

1.25V

10␮F

REF OUT1

REF OUT2

REF IN

CLOCK

LATCH

DATA

COM

C1 C2 C3

BOOST

AD421

0.01␮F

COMP

DRIVE

LOOP

RTN

0.01␮F

1k⍀

1000pF

POWER

LOOP

Figure 23. Smart Transmitter Employing the AD7709

–28–

REV. A

Page 29

OUTLINE DIMENSIONS

24-Lead Thin Shrink Small Outline Package [TSSOP]

(RU-24)

Dimensions shown in millimeters

7.90

7.80

7.70

AD7709

PIN 1

0.15

0.05

0.10 COPLANARITY

4.50

4.40

4.30

121

0.65 BSC

0.30

0.19

COMPLIANT TO JEDEC STANDARDS MO-153AD

1.20

MAX

SEATING PLANE

6.40 BSC

0.20

0.09

8 0

0.75

0.60

0.45

REV. A

–29–

Page 30

AD7709

Revision History

Location Page

3/03—Data Sheet changed from REV. 0 to REV. A.

Changes to SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Change to Communications Register map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Changes to Table VIII. Filter Register Bit Designations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Updated OUTLINE DIMENSIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

–30–

REV. A

Page 31

–31–

Page 32

C02700–0–3/03(A)

–32–

PRINTED IN U.S.A.

Datasheet AD7709 Datasheet (Analog Devices)

Specifications and Main Features

Frequently Asked Questions

User Manual

GENERAL DESCRIPTION

FUNCTIONAL BLOCK DIAGRAM

INTERFACE

TABLE OF CONTENTS

SPECIFICATIONS

TIMING CHARACTERISTICS

ABSOLUTE MAXIMUM RATINGS*

ORDERING GUIDE

PIN CONFIGURATION

PIN FUNCTION DESCRIPTIONS

NOISE PERFORMANCE

ON-CHIP REGISTERS

Communications Register (A1, A0 = 0, 0)

Status Register (A1, A0 = 0, 0; Power-On-Reset = 00H)

Configuration Register (A1, A0 = 0, 1; Power-On-Reset = 000007H)

Filter Register (A1, A0 = 1, 0; Power-On-Reset = 45h)

CONFIGURING THE AD7709

DIGITAL INTERFACE

MICROCOMPUTER/MICROPROCESSOR INTERFACING

AD7709-to-68HC11 Interface

AD7709-to-8051 Interface

AD7709-to-ADSP-2103/ADSP-2105 Interface

CIRCUIT DESCRIPTION

Analog Input Channels

Programmable Gain Amplifier

Bipolar/Unipolar Configuration

Data Output Coding

Excitation Currents

Crystal Oscillator

Reference Input

Reset Input

Power-Down Mode

Grounding and Layout

APPLICATIONS

Pressure Measurement

Temperature Measurement

3-Wire RTD Configurations

Smart Transmitters

OUTLINE DIMENSIONS

Revision History