Datasheet AD7665 Datasheet (Analog Devices)

a

16-Bit, 570 kSPS CMOS ADC

FEATURES
Throughput

570 kSPS (Warp Mode)

500 kSPS (Normal Mode)
INL: 2.5 LSB Max (0.0038% of Full Scale)
16-Bit Resolution with No Missing Codes
S/(N+D): 90 dB Typ @ 180 kHz
THD: –100 dB Typ @ 180 kHz
Analog Input Voltage Ranges

Bipolar: 10 V, 5 V, 2.5 V

Unipolar: 0 V to 10 V, 0 V to 5 V, 0 V to 2.5 V
Both AC and DC Specifications
No Pipeline Delay
Parallel (8/16 Bits) and Serial 5 V/3 V Interface

®

/QSPI™/MICROWIRE™/DSP Compatible

SPI
Single 5 V Supply Operation
Power Dissipation

64 mW Typical

15 W @ 100 SPS
Power-Down Mode: 7 W Max
Package: 48-Lead Quad Flatpack (LQFP)
Package: 48-Lead Chip Scale (LFCSP)
Pin-to-Pin Compatible Upgrade of the AD7664/AD7663

APPLICATIONS
Data Acquisition
Communication
Instrumentation
Spectrum Analysis
Medical Instruments
Process Control

AD7665

*

FUNCTIONAL BLOCK DIAGRAM

DGNDDVDDAVDD AGND REF REFGND

PD

4R

4R

2R

R

SWITCHED

CAP DAC

CONTROL LOGIC AND

CALIBRATION CIRCUITRY

AD7665

CLOCK

CNVSTIMPULSEWARP

SERIAL

PORT

PARALLEL

INTERFACE

16

OVDD

OGND

SER/PAR

BUSY

D[15:0]

CS

RD

OB/2C

BYTESWAP

IND(4R)

INC(4R)

INB(2R)

INA(R)

INGND

RESET

PulSAR Selection

Type/kSPS 100–250 500–570 800–1000

Pseudo AD7660 AD7650
Differential AD7664

True Bipolar AD7663 AD7665 AD7671

True Differential AD7675 AD7676 AD7677

18-Bit AD7678 AD7673 AD7674

Simultaneous/ AD7654 AD7665
Multichannel

GENERAL DESCRIPTION

The AD7665 is a 16-bit, 570 kSPS, charge redistribution SAR,
analog-to-digital converter that operates from a single 5 V power
supply. It contains a high speed 16-bit sampling ADC, a resistor
input scaler that allows various input ranges, an internal conver­sion clock, error correction circuits, and both serial and parallel
system interface ports.

The AD7665 is hardware factory-calibrated and is comprehen­sively tested to ensure such ac parameters as signal-to-noise ratio
(SNR) and total harmonic distortion (THD), in addition to the
more traditional dc parameters of gain, offset, and linearity.

It features a very high sampling rate mode (Warp), a fast mode
(Normal) for asynchronous conversion rate applications, and for
low power applications, a reduced power mode (Impulse) where
the power is scaled with the throughput.

*Patent pending

REV. B

Information furnished by Analog Devices is believed to be accurate and
reliable. However, no responsibility is assumed by Analog Devices for its
use, nor for any infringements of patents or other rights of third parties that
may result from its use. No license is granted by implication or otherwise
under any patent or patent rights of Analog Devices. Trademarks and
registered trademarks are the property of their respective companies.

It is fabricated using Analog Devices’ high performance, 0.6 micron
CMOS process and is available in a 48-lead LQFP and a tiny
48-lead LFCSP with operation specified from –40°C to +85°C.

PRODUCT HIGHLIGHTS

1. Fast Throughput
The AD7665 is a very high speed (570 kSPS in Warp Mode
and 500 kSPS in Normal Mode), charge redistribution, 16-bit
SAR ADC.

2. Single-Supply Operation
The AD7665 operates from a single 5 V supply, dissipates
only 64 mW typical, even lower when a reduced throughput
is used with the reduced power mode (Impulse) and a power­down mode.

3. Superior INL
The AD7665 has a maximum integral nonlinearity of 2.5 LSB
with no missing 16-bit code.

4. Serial or Parallel Interface
Versatile parallel (8 bits or 16 bits) or 2-wire serial interface
arrangement compatible with both 3 V or 5 V logic.

One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: [phone] www.analog.com
Fax: [phone] © 2003 Analog Devices, Inc. All rights reserved.

AD7665–SPECIFICATIONS

(–40C to +85C, AVDD = DVDD = 5 V, OVDD = 2.7 V to 5.25 V, unless otherwise noted.)

Parameter Conditions Min Typ Max Unit

RESOLUTION 16 Bits

ANALOG INPUT

Voltage Range V
Common-Mode Input Voltage V
Analog Input CMRR f

– V

IND

INGND

INGND

= 180 kHz 62 dB

IN

±4 REF, 0 V to 4 REF, ±2 REF (See Table I)
–0.1 +0.5 V

Input Impedance See Table I

THROUGHPUT SPEED

Complete Cycle In Warp Mode 1.75 µs
Throughput Rate In Warp Mode 1 570 kSPS
Time between Conversions In Warp Mode 1 ms
Complete Cycle In Normal Mode 2 µs
Throughput Rate In Normal Mode 0 500 kSPS
Complete Cycle In Impulse Mode 2.25 µs
Throughput Rate In Impulse Mode 0 444 kSPS

DC ACCURACY

Integral Linearity Error –2.5 +2.5 LSB

1

No Missing Codes 16 Bits
Transition Noise 0.7 LSB
Bipolar Zero Error

2

, T

MIN

to T

MAX

±5 V Range, Normal or –25 +25 LSB
Impulse Modes

2

Bipolar Full-Scale Error
Unipolar Zero Error

2

, T

, T

MIN

Unipolar Full-Scale Error

2

, T

MIN

to T

MIN

to T

MAX

to T

MAX

Other Range or Mode –0.06 +0.06 % of FSR

–0.25 +0.25 % of FSR
–0.18 +0.18 % of FSR

MAX

–0.38 +0.38 % of FSR

Power Supply Sensitivity AVDD = 5 V ±5% ±9.5 LSB

AC ACCURACY

Signal-to-Noise f

= 10 kHz 89 90 dB

IN

3

fIN = 180 kHz 90 dB
Spurious-Free Dynamic Range fIN = 180 kHz 100 dB
Total Harmonic Distortion f

= 180 kHz –100 dB

IN

Signal-to-(Noise+Distortion) fIN = 10 kHz 88.5 90 dB

= 180 kHz, –60 dB Input 30 dB

f

IN

–3 dB Input Bandwidth 3.6 MHz

SAMPLING DYNAMICS

Aperture Delay 2ns
Aperture Jitter 5 ps rms
Transient Response Full-Scale Step 1 µs

REFERENCE

External Reference Voltage Range 2.3 2.5 AVDD – 1.85 V
External Reference Current Drain 570 kSPS Throughput 114 µA

DIGITAL INPUTS

Logic Levels

V

IL

V

IH

I

IL

I

IH

–0.3 +0.8 V
+2.0 DVDD + 0.3 V
–1 +1 µA
–1 +1 µA

DIGITAL OUTPUTS

Data Format Parallel or Serial 16-Bit
Pipeline Delay Conversion Results Available Immediately

after Completed Conversion

I

V

OL

V

OH

= 1.6 mA 0.4 V

SINK

I

= –570 µA OVDD – 0.6 V

SOURCE

POWER SUPPLIES

Specified Performance

AVDD 4.75 5 5.25 V
DVDD 4.75 5 5.25 V
OVDD 2.7 5.25

Operating Current

AVDD 14 mA

6

DVDD

6

OVDD

5

570 kSPS Throughput

4.5 mA
20 µA

4

V

–2–

REV. B

AD7665

Parameter Conditions Min Typ Max Unit

POWER SUPPLIES (Continued)

Power Dissipation

In Power-Down Mode

TEMPERATURE RANGE

Specified Performance T

NOTES

1

LSB means least significant bit. With the ±5 V input range, one LSB is 152.588 µV.

2

See Definition of Specifications section. These specifications do not include the error contribution from the external reference.

3

All specifications in dB are referred to a full-scale input FS. Tested with an input signal at 0.5 dB below full scale, unless otherwise specified.

4

The max should be the minimum of 5.25 V and DVDD + 0.3 V.

5

In Warp Mode.

6

Tested in Parallel Reading Mode.

7

Tested with the 0 V to 5 V range and VIN – V

8

In Impulse Mode.

9

With OVDD below DVDD + 0.3 V and all digital inputs forced to DVDD or DGND, respectively.

10

Contact factory for extended temperature range.

Specifications subject to change without notice.

6, 7

444 kSPS Throughput
100 SPS Throughput

9

10

570 kSPS Throughput

to T

MIN

INGND

MAX

= 0 V. See Power Dissipation section.

8

8

5

64 74 mW
15 µW
93 107 mW

7µW

–40 +85 °C

Table I. Analog Input Configuration

Input Voltage Input
Range IND(4R) INC(4R) INB(2R) INA(R) Impedance

±4 REF
±2 REF V
±REF V
0 V to 4 REF V
0 V to 2 REF V
0 V to REF V

NOTES

1

2

3

TIMING SPECIFICATIONS

Parameter

2

Typical analog input impedance.
With REF = 3 V, in this range, the input should be limited to –11 V to +12 V.
For this range the input is high impedance.

V

IN

IN

IN

IN

IN

IN

INGND INGND REF 5.85 kW
V

IN

V

IN

V

IN

V

IN

V

IN

(–40C to +85C, AVDD = DVDD = 5 V, OVDD = 2.7 V to 5.25 V, unless otherwise noted.)

INGND REF 3.41 kW
V

IN

REF 2.56 kW

INGND INGND 3.41 kW
V

IN

V

IN

INGND 2.56 kW
V

IN

Note 3

Symbol Min Typ Max Unit

Refer to Figures 11 and 12

Convert Pulsewidth t
Time between Conversions t

1

2

5ns

1.75/2/2.25 Note 1 µs

(Warp Mode/Normal Mode/Impulse Mode)

CNVST LOW to BUSY HIGH Delay t
BUSY HIGH All Modes Except in Master Serial Read after t

3

4

30 ns

0.75/1/1.25 µs

Convert Mode (Warp Mode/Normal Mode/Impulse Mode)
Aperture Delay t
End of Conversion to BUSY LOW Delay t
Conversion Time (Warp Mode/Normal Mode/Impulse Mode) t
Acquisition Time t
RESET Pulsewidth t

5

6

7

8

9

10 ns

1µs
10 ns

2ns

0.75/1/1.25 µs

Refer to Figures 13, 14, 15, and 16 (Parallel Interface Modes)

CNVST LOW to DATA Valid Delay t

10

0.75/1/1.25 µs

(Warp Mode/Normal Mode/Impulse Mode)
DATA Valid to BUSY LOW Delay t
Bus Access Request to DATA Valid t
Bus Relinquish Time t

11

12

13

20 ns

40 ns

515ns

1

REV. B

–3–

AD7665

TIMING SPECIFICATIONS

Parameter

Refer to Figures 17 and 18 (Master Serial Interface Modes)

CS LOW to SYNC Valid Delay t
CS LOW to Internal SCLK Valid Delay t
CS LOW to SDOUT Delay t
CNVST LOW to SYNC Delay (Read during Convert) t

(Warp Mode/Normal Mode/Impulse Mode)
SYNC Asserted to SCLK First Edge Delay
Internal SCLK Period
Internal SCLK HIGH
Internal SCLK LOW
SDOUT Valid Setup Time
SDOUT Valid Hold Time
SCLK Last Edge to SYNC Delay

CS HIGH to SYNC HI-Z t
CS HIGH to Internal SCLK HI-Z t
CS HIGH to SDOUT HI-Z t

BUSY HIGH in Master Serial Read after Convert
CNVST LOW to SYNC Asserted Delay t

3

3

3

3

3

(continued)

3

Symbol Min Typ Max Unit

2

14

15

16

17

3

3

t

18

t

19

t

20

t

21

t

22

t

23

t

24

25

26

27

t

28

29

4ns
25 40 ns
15 ns

9.5 ns

4.5 ns
2ns
3

(Warp Mode/Normal Mode/Impulse Mode)

Master Serial Read after Convert
SYNC Deasserted to BUSY LOW Delay t

30

Refer to Figures 19 and 21 (Slave Serial Interface Modes)

External SCLK Setup Time t
External SCLK Active Edge to SDOUT Delay t
SDIN Setup Time t
SDIN Hold Time t
External SCLK Period t
External SCLK HIGH t
External SCLK LOW t

NOTES

1

In Warp Mode only, the maximum time between conversions is 1 ms, otherwise, there is no required maximum time.

2

In Serial Interface Modes, the SYNC, SCLK, and SDOUT timings are defined with a maximum load C

3

In Serial Master Read During Convert Mode. See Table II for Master Read after Convert Mode.

Specifications subject to change without notice.

31

32

33

34

35

36

37

5ns
316ns
5ns
5ns
25 ns
10 ns
10 ns

of 10 pF; otherwise, the load is 60 pF maximum.

L

10 ns
10 ns
10 ns

25/275/525 ns

10 ns
10 ns
10 ns

See Table II µs

0.75/1/1.25 µs

25 ns

Table II. Serial Clock Timings in Master Read after Convert

DIVSCLK[1] 0011
DIVSCLK[0] 0101 Unit

SYNC to SCLK First Edge Delay Minimum t
Internal SCLK Period Minimum t
Internal SCLK Period Maximum t
Internal SCLK HIGH Minimum t
Internal SCLK LOW Minimum t
SDOUT Valid Setup Time Minimum t
SDOUT Valid Hold Time Minimum t
SCLK Last Edge to SYNC Delay Minimum t
BUSY HIGH Width Maximum (Warp) t
BUSY HIGH Width Maximum (Normal) t
BUSY HIGH Width Maximum (Impulse) t

18

19

19

20

21

22

23

24

28

28

28

4202020 ns
25 50 100 200 ns
40 70 140 280 ns
15 25 50 100 ns

9.5 24 49 99 ns

4.5 22 22 22 ns
243090 ns
360140 300 ns

1.5 2 3 5.25 µs

1.75 2.25 3.25 5.5 µs
2 2.5 3.5 5.75 µs

–4–

REV. B

AD7665

36

35

34

33

32

31

30

29

28

27

26

25

13 14

15 16 17 18 19 20 21 22 23 24

1

2

3

4

5

6

7

8

9

10

11

12

48

47 46 45 44 39 38 3743 42 41 40

PIN 1
IDENTIFIER

TOP VIEW

(Not to Scale)

AGND

CNVST

PD

RESET

CS
RD

DGND

AGND
AVDD

NC

BYTESWAP

OB/2C
WARP

IMPULSE

NC = NO CONNECT

SER/PAR

D0

D1

D2/DIVSCLK[0]

BUSY

D15

D14

D13

AD7665

D3/DIVSCLK[1]

D12

D4/EXT/INT

D5/INVSYNC

D6/INVSCLK

D7/RDC/SDIN

OGND

OVDD

DVDD

DGND

D8/SDOUT

D9/SCLK

D10/SYNC

D11/RDERROR

NCNCNCNCNC

IND(4R)

INC(4R)

INB(2R)

INA(R)

INGND

REFGND

REF

ABSOLUTE MAXIMUM RATINGS

Analog Inputs

2

, INC2, INB2 . . . . . . . . . . . . . . . . . . . . –11 V to +30 V

IND

1

INA, REF, INGND, REFGND

. . . . . . . . . . . . . . . . . . . . . AGND – 0.3 V to AVDD + 0.3 V

Ground Voltage Differences

AGND, DGND, OGND . . . . . . . . . . . . . . . . . . . . . ±0.3 V

Supply Voltages

AVDD, DVDD, OVDD . . . . . . . . . . . . . . . . –0.3 V to + 7 V

AVDD to DVDD,

AVDD to OVDD . . . . . . . . . . . . . . ±7 V

DVDD to OVDD . . . . . . . . . . . . . . . . . . . . . –0.3 V to + 7 V

Digital Inputs . . . . . . . . . . . . . . . . –0.3 V to DVDD + 0.3 V

Internal Power Dissipation

3

. . . . . . . . . . . . . . . . . . . . 700 mW

Internal Power Dissipation4 . . . . . . . . . . . . . . . . . . . . . . 2.5 W

Junction Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . 150°C

Storage Temperature Range . . . . . . . . . . . . –65°C to +150°C

Lead Temperature Range

(Soldering 10 sec) . . . . . . . . . . . . . . . . . . . . . . . . . . . 300°C

1

Stresses above those listed under Absolute Maximum Ratings may cause perma­nent damage to the device. This is a stress rating only; functional operation of the
device at these or any other conditions above those indicated in the operational
section of this specification is not implied. Exposure to absolute maximum rating
conditions for extended periods may affect device reliability.

2

See Analog Inputs section.

3

Specification is for device in free air: 48-Lead LQFP: qJA = 91°C/W, qJC = 30°C/W.

4

Specification is for device in free air: 48-Lead LFCSP: qJC = 26°C/W.

PIN CONFIGURATION

ST-48 and CP-48

1.6mA I

TO OUTPUT

PIN

*

IN SERIAL INTERFACE MODES, THE SYNC, SCLK, AND

SDOUT TIMINGS ARE DEFINED WITH A MAXIMUM LOAD

OF 10pF; OTHERWISE, THE LOAD IS 60pF MAXIMUM.

C

L

C

L

60pF

*

500A

Figure 1. Load Circuit for Digital Interface Timing, SDOUT,
SYNC, SCLK Outputs, C

= 10 pF

L

OL

1.4V

I

OH

0.8V

t

DELAY

0.8V 0.8V

2V

t

DELAY

2V2V

Figure 2. Voltage Reference Levels for Timing

ORDERING GUIDE

Model Temperature Range Package Description Package Option

AD7665AST –40°C to +85°C Quad Flatpack (LQFP) ST-48
AD7665ASTRL –40°C to +85°C Quad Flatpack (LQFP) ST-48
AD7665ACP –40°C to +85°C Chip Scale (LFCSP) CP-48
AD7665ACPRL –40°C to +85°C Chip Scale (LFCSP) CP-48
EVAL-AD7665CB
EVAL-CONTROL BRD2

NOTES

1

This board can be used as a standalone evaluation board or in conjunction with the EVAL-CONTROL BRD2 for evaluation/demonstration purposes.

2

This board allows a PC to control and communicate with all Analog Devices evaluation boards ending in the CB designators.

CAUTION

ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily
accumulate on the human body and test equipment and can discharge without detection. Although
the AD7665 features proprietary ESD protection circuitry, permanent damage may occur on
devices subjected to high energy electrostatic discharges. Therefore, proper ESD precautions are
recommended to avoid performance degradation or loss of functionality.

REV. B

1

2

Evaluation Board
Controller Board

–5–

AD7665

PIN FUNCTION DESCRIPTION

Pin
No. Mnemonic Type Description

1 AGND P Analog Power Ground Pin.
2 AVDD P Input Analog Power Pin. Nominally 5 V.
3, 44–48 NC No Connect.
4 BYTESWAP Parallel Mode Selection (8/16 Bit). When LOW, the LSB is output on D[7:0] and the MSB is

output on D[15:8]. When HIGH, the LSB is output on D[15:8] and the MSB is output on D[7:0].

5OB/2C DI Straight Binary/Binary Twos Complement. When OB/2C is HIGH, the digital output is straight

binary; when LOW, the MSB is inverted, resulting in a twos complement output from its internal
shift register.

6 WARP DI Mode Selection. When HIGH and IMPULSE LOW, this input selects the fastest mode, the

maximum throughput is achievable, and a minimum conversion rate must be applied in order
to guarantee full specified accuracy. When LOW, full accuracy is maintained independent of
the minimum conversion rate.

7 IMPULSE DI Mode Selection. When HIGH and WARP LOW, this input selects a reduced Power Mode.

In this mode, the power dissipation is approximately proportional to the sampling rate.

8 SER/PAR DI Serial/Parallel Selection Input. When LOW, the Parallel Port is selected; when HIGH, the

Serial Interface Mode is selected and some bits of the data bus are used as a Serial Port.

9, 10 D[0:1] DO Bit 0 and Bit 1 of the Parallel Port Data Output Bus. When SER/PAR is HIGH, these outputs

are in high impedance.

11, 12 D[2:3] or DI/O When SER/PAR is LOW, these outputs are used as Bit 2 and Bit 3 of the Parallel Port Data

Output Bus.

DIVSCLK[0:1] When SER/PAR is HIGH, EXT/INT is LOW and RDC/SDIN is LOW, which is the Serial

Master Read after Convert Mode. These inputs, part of the Serial Port, are used to slow down,
if desired, the internal serial clock that clocks the data output. In the other serial modes, these
pins are high impedance outputs.

13 D[4] DI/O When SER/PAR is LOW, this output is used as Bit 4 of the Parallel Port Data Output Bus.

or EXT/INT When SER/PAR is HIGH, this input, part of the Serial Port, is used as a digital select input for

choosing the internal or an external data clock, called respectively, Master and Slave Modes.
With EXT/INT tied LOW, the internal clock is selected on SCLK output. With EXT/INT set to a
logic HIGH, output data is synchronized to an external clock signal connected to the SCLK
input and the external clock is gated by CS.

14 D[5] DI/O When SER/PAR is LOW, this output is used as Bit 5 of the Parallel Port Data Output Bus.

or INVSYNC When SER/PAR is HIGH, this input, part of the Serial Port, is used to select the active state

of the SYNC signal. When LOW, SYNC is active HIGH. When HIGH, SYNC is active LOW.

15 D[6] DI/O When SER/PAR is LOW, this output is used as Bit 6 of the Parallel Port Data Output Bus.

or INVSCLK When SER/PAR is HIGH, this input, part of the Serial Port, is used to invert the SCLK signal.

It is active in both master and slave mode.

16 D[7] DI/O When SER/PAR is LOW, this output is used as Bit 7 of the Parallel Port Data Output Bus.

or RDC/SDIN When SER/PAR is HIGH, this input, part of the Serial Port, is used as either an external data

input or a read mode selection input, depending on the state of EXT/INT.
When EXT/INT is HIGH, RDC/SDIN could be used as a data input to daisy-chain the conversion
results from two or more ADCs onto a single SDOUT line. The digital data level on SDIN is
output on DATA with a delay of 16 SCLK periods after the initiation of the read sequence.

When EXT/INT is LOW, RDC/SDIN is used to select the Read Mode. When RDC/SDIN is
HIGH, the previous data is output on SDOUT during conversion. When RDC/SDIN is LOW,
the data can be output on SDOUT only when the conversion is complete.

17 OGND P Input/Output Interface Digital Power Ground.

18 OVDD P Input/Output Interface Digital Power. Nominally at the same supply as the supply of the host

interface (5 V or 3 V).
19 DVDD P Digital Power. Nominally at 5 V.
20 DGND P Digital Power Ground.

–6–

REV. B

AD7665

PIN FUNCTION DESCRIPTION (continued)

Pin
No. Mnemonic Type Description

21 D[8] DO When SER/PAR is LOW, this output is used as Bit 8 of the Parallel Port Data Output Bus.

or SDOUT When SER/PAR is HIGH, this output, part of the Serial Port, is used as a serial data output

synchronized to SCLK. Conversion results are stored in an on-chip register. The AD7665
provides the conversion result, MSB first, from its internal shift register. The data format is
determined by the logic level of OB/2C. In Serial Mode, when EXT/INT is LOW, SDOUT is
valid on both edges of SCLK.

In serial mode, when EXT/INT is HIGH:
If INVSCLK is LOW, SDOUT is updated on the SCLK rising edge and valid on the next

falling edge.
If INVSCLK is HIGH, SDOUT is updated on the SCLK falling edge and valid on the next

rising edge.

22 D[9] DI/O When SER/PAR is LOW, this output is used as Bit 9 of the Parallel Port Data Output Bus.

or SCLK When SER/PAR is HIGH, this pin, part of the Serial Port, is used as a serial data clock input

or output, dependent upon the logic state of the EXT/INT pin. The active edge where the data
SDOUT is updated depends upon the logic state of the INVSCLK pin.

23 D[10] DO When SER/PAR is LOW, this output is used as Bit 10 of the Parallel Port Data Output Bus.

or SYNC When SER/PAR is HIGH, this output, part of the Serial Port, is used as a digital output frame

synchronization for use with the internal data clock (EXT/INT = Logic LOW). When a read
sequence is initiated and INVSYNC is LOW, SYNC is driven HIGH and remains HIGH
while SDOUT output is valid. When a read sequence is initiated and INVSYNC is HIGH,
SYNC is driven LOW and remains LOW while SDOUT output is valid.

24 D[11] DO When SER/PAR is LOW, this output is used as Bit 11 of the Parallel Port Data Output Bus.

or RDERROR When SER/PAR is HIGH and EXT/INT is HIGH, this output, part of the Serial Port, is used as

an incomplete read error flag. In Slave Mode, when a data read is started and not complete when
the following conversion is complete, the current data is lost and RDERROR is pulsed HIGH.

25–28 D[12:15] DO Bit 12 to Bit 15 of the Parallel Port Data Output Bus. When SER/PAR is HIGH, these outputs

are in high impedance.

29 BUSY DO Busy Output. Transitions HIGH when a conversion is started and remains HIGH until the

conversion is complete and the data is latched into the on-chip shift register. The falling edge
of BUSY could be used as a data-ready clock signal.

30 DGND P Must Be Tied to Digital Ground.
31 RD DI Read Data. When CS and RD are both LOW, the Interface Parallel or Serial Output Bus is enabled.
32 CS DI Chip Select. When CS and RD are both LOW, the Interface Parallel or Serial Output Bus is

enabled. CS is also used to gate the external serial clock.

33 RESET DI Reset Input. When set to a logic HIGH, reset the AD7665. Current conversion, if any, is aborted.

If not used, this pin could be tied to DGND.

34 PD DI Power-Down Input. When set to a logic HIGH, power consumption is reduced and conversions

are inhibited after the current one is completed.

35 CNVST DI Start Conversion. A falling edge on CNVST puts the internal sample-and-hold into the hold state

and initiates a conversion. In Impulse Mode (IMPULSE HIGH and WARP LOW), if CNVST
is held LOW when the acquisition phase (t

into the hold state and a conversion is immediately started.
36 AGND P Must Be Tied to Analog Ground.
37 REF AI Reference Input Voltage.
38 REFGND AI Reference Input Analog Ground.
39 INGND AI Analog Input Ground.
40, 41, INA, INB, AI Analog Inputs. Refer to Table I for input range configuration.

42, 43 INC, IND

NOTES
AI = Analog Input
DI = Digital Input
DI/O = Bidirectional Digital
DO = Digital Output
P = Power

) is complete, the internal sample-and-hold is put

8

REV. B

–7–

AD7665

DEFINITION OF SPECIFICATIONS
Internal Nonlinearity Error (INL)

Linearity error refers to the deviation of each individual code
from a line drawn from “negative full scale” through “positive
full scale.” The point used as negative full scale occurs 1/2 LSB
before the first code transition. Positive full scale is defined as a
level 1 1/2 LSB beyond the last code transition. The deviation is
measured from the middle of each code to the true straight line.

Differential Nonlinearity Error (DNL)

In an ideal ADC, code transitions are 1 LSB apart. Differential
nonlinearity is the maximum deviation from this ideal value. It is
often specified in terms of resolution for which no missing codes
are guaranteed.

Full-Scale Error

The last transition (from 011 . . . 10 to 011 ...11 in twos
complement coding) should occur for an analog voltage 1 1/2 LSB
below the nominal full scale (2.499886 V for the ±2.5 V range).
The full-scale error is the deviation of the actual level of the last
transition from the ideal level.

Bipolar Zero Error

The difference between the ideal midscale input voltage (0 V) and
the actual voltage producing the midscale output code.

Unipolar Zero Error

In Unipolar Mode, the first transition should occur at a level
1/2 LSB above analog ground. The unipolar zero error is the
deviation of the actual transition from that point.

Spurious-Free Dynamic Range (SFDR)

The difference, in decibels (dB), between the rms amplitude of
the input signal and the peak spurious signal.

Effective Number of Bits (ENOB)

A measurement of the resolution with a sine wave input. It is
related to S/(N+D) by the following formula:

ENOB S N D

and is expressed in bits.

Total Harmonic Distortion (THD)

The rms sum of the first five harmonic components to the rms
value of a full-scale input signal, expressed in decibels.

Signal-To-Noise Ratio (SNR)

The ratio of the rms value of the actual input signal to the
rms sum of all other spectral components below the Nyquist
frequency, excluding harmonics and dc. The value for SNR is
expressed in decibels.

Signal To (Noise + Distortion) Ratio (S/[N+D])

The ratio of the rms value of the actual input signal to the rms sum
of all other spectral components below the Nyquist frequency,
including harmonics but excluding dc. The value for S/(N+D) is
expressed in decibels.

Aperture Delay

A measure of the acquisition performance measured from the
falling edge of the CNVST input to when the input signal is
held for a conversion.

Transient Response

The time required for the AD7665 to achieve its rated accuracy
after a full-scale step function is applied to its input.

=+

[]

()

-

176 602..

dB

)

–8–

REV. B

Typical Performance Characteristics–AD7665

80

70

60

50

40

30

20

10

0

–3.0 –2.7 –2.4 –2.1 –1.8 –1.5 –1.2 –0.9 –0.6 –0.3

NUMBER OF UNITS

NEGATIVE INL – LSB

0019

932

7337

7204

870

22 0 0

0

1000

2000

3000

4000

5000

6000

7000

8000

7FFD 7FFE 7FFF 8000 8001 8002 8003 8004 8005 8005

CODE IN HEXA

COUNTS

001

214

3310

9468

3259

131

100

0

1000

2000

3000

4000

5000

6000

7000

8000

9000

10000

7FFC 7FFD 7FFE 7FFF 8000 8001 8002 8003 8004 8005 8006

CODE IN HEXA

COUNTS

TPC 1. Integral Nonlinearity vs. Code

TPC 2. Differential Nonlinearity vs. Code

70

60

TPC 4. Typical Negative INL Distribution (446 Units)

TPC 5. Histogram of 16,384 Conversions of a DC Input
at the Code Transition

50

40

30

NUMBER OF UNITS

20

REV. B

10

0

0 0.3 0.6 0.9 1.2 1.5 1.8 2.1 2.4 2.7 3.0

TPC 3. Typical Positive INL Distribution (446 Units)

POSITIVE INL – LSB

TPC 6. Histogram of 16,384 Conversions of a DC Input
at the Code Center

–9–

AD7665

96

93

90

87

84

–98

–100

–102

–104

–55 –35 –15 5 25 45 65 85 105 125

SNR – dB

THD – dB

TEMPERATURE – C

THD

SNR

–0

–20

–40

–60

–80

–100

–120

–140

AMPLITUDE – dB OF FULL SCALE

–160

–180

0 57 114 171 228 285

FREQUENCY – kHz

4096 POINT FFT
FS = 571kHz

= 45kHz, –0.5dB

f

IN

SNR = 90.1 dB
SINAD = 89.7dB
THD = –100.1dB
SFDR = 102.3dB

TPC 7. FFT Plot

100

95

90

85

80

SNR AND S/[N +D] – dB

75

70

SNR

SINAD

ENOB

1 10 100 1000

FREQUENCY – kHz

TPC 8. SNR, S/(N+D), and ENOB vs. Frequency

16.0

15.5

15.0

14.5

14.0

13.5

13.0

ENOB – Bits

TPC 10. SNR, THD vs. Temperature

–60

–65

–70

–75

–80

–85

–90

–95

THD, HARMONICS – dB

–100

–105

–110

–115

SFDR

SECOND HARMONIC

THD

THIRD HARMONIC

1 10 100 1000

FREQUENCY – kHz

TPC 11. THD, Harmonics, and SFDR vs. Frequency

110

105

100

95

90

85

80

75

70

65

60

SFDR – dB

92

90

88

SNR – (REFERRED TO FULL SCALE) – dB

86

–80 –70 –60 –50 –40 –30 –20 –10 0

INPUT LEVEL – dB

TPC 9. SNR vs. Input Level

–10–

–60

–70

–80

–90

–100

SECOND HARMONIC

–110

–120

THD, HARMONICS – dB

–130

–140

–150

THIRD HARMONIC

–60 –50 –40 –30 –20 –10 0

INPUT LEVEL – dB

THD

TPC 12. THD, Harmonics vs. Input Level

REV. B

AD7665

TEMPERATURE – C

10

–10

–55 125–35

LSB

–15 5 25 456585105

8

0

–4

–6

–8

6

4

–2

2

OFFSET

–FS

+FS

50

40

30

DELAY – ns

20

12

t

10

0

0 50 100 150 200

CL – pF

TPC 13. Typical Delay vs. Load Capacitance CL

100000

DVDD, WARP/NORMAL

10

1

AV DD, WARP/NORMAL

AV DD , IMPULSE

DVD D, IMPULSE

10000

1000

100

1000

900

800

700

600

500

400

300

200

100

POWER-DOWN OPERATING CURRENTS – nA

0
–55 –35 –15 5 25 45 65 85 105

TEMPERATURE – C

DVD D

OVD D

AV DD

TPC 15. Power-Down Operating Currents vs. Temperature

0.1

OPERATING CURRENTS – A

0.01

0.001
1 10 100 1000 10000 100000 1000000

SAMPLING RATE – SPS

TPC 14. Operating Currents vs. Sample Rate

REV. B

OVD D, ALL MODES

TPC 16. +FS, Offset, and –FS vs. Temperature

–11–

AD7665

IND

INC

INB

INA

4R

4R

2R

R

REF

REFGND

INGND

32,768C

MSB

16,384C

SWITCHES

A

COMP

CONTROL

CONTROL

CNVST

LOGIC

BUSY

OUTPUT

CODE

SW

LSB

4C

2C

CC

65,536C

SW

B

Figure 3. ADC Simplified Schematic

CIRCUIT INFORMATION

The AD7665 is a fast, low power, single-supply, precise 16-bit
analog-to-digital converter (ADC). The AD7665 features different
modes to optimize performances according to the applications.
In Warp Mode, the AD7665 is capable of converting 570,000
samples per second (570 kSPS).

The AD7665 provides the user with an on-chip track-and-hold,
successive approximation ADC that does not exhibit any pipeline
or latency, making it ideal for multiple multiplexed channel
applications.

It is specified to operate with both bipolar and unipolar input
ranges by changing the connection of its input resistive scaler.

The AD7665 can be operated from a single 5 V supply and be
interfaced to either 5 V or 3 V digital logic. It is housed in a
48-lead LQFP package or a 48-lead LFCSP package that com­bines space savings and flexible configurations as either serial
or parallel interface. The AD7665 is a pin-to-pin compatible
upgrade of the AD7663 and AD7664.

CONVERTER OPERATION

The AD7665 is a successive approximation analog-to-digital
converter based on a charge redistribution DAC. Figure 3 shows
the simplified schematic of the ADC. The input analog signal is
first scaled down and level shifted by the internal input resistive
scaler, which allows both unipolar ranges (0 V to 2.5 V, 0 V to 5 V,
and 0 V to 10 V) and bipolar ranges (±2.5 V, ±5 V, and ±10 V). The
output voltage range of the resistive scaler is always 0 V to 2.5 V.
The capacitive DAC consists of an array of 16 binary weighted
capacitors and an additional “LSB” capacitor. The comparator’s
negative input is connected to a “dummy” capacitor of the same
value as the capacitive DAC array.

During the acquisition phase, the common terminal of the array
tied to the comparator’s positive input is connected to AGND
via SW

. All independent switches are connected to the output

A

of the resistive scaler. Thus, the capacitor array is used as a
sampling capacitor and acquires the analog signal. Similarly, the
dummy capacitor acquires the analog signal on INGND input.

When the acquisition phase is complete, and the CNVST input goes
or is LOW, a conversion phase is initiated. When the conversion
phase begins, SW

and SWB are opened first. The capacitor array

A

and the dummy capacitor are then disconnected from the inputs
and connected to the REFGND input. Therefore, the differential
voltage between the output of the resistive scaler and INGND
captured at the end of the acquisition phase is applied to the
comparator inputs, causing the comparator to become unbalanced.

By switching each element of the capacitor array between REFGND
or REF, the comparator input varies by binary weighted voltage

–12–

steps (V

REF

/2, V

/4 ...V

REF

/65,536). The control logic toggles

REF

these switches, starting with the MSB first, in order to bring the
comparator back into a balanced condition. After the completion
of this process, the control logic generates the ADC output code
and brings BUSY output LOW.

Modes of Operation

The AD7665 features three modes of operation, Warp, Normal,
and Impulse. Each of these modes is more suitable for specific
applications.

The Warp Mode allows the fastest conversion rate up to 570 kSPS.
However, in this mode and this mode only, the full specified accu­racy is guaranteed only when the time between conversion does
not exceed 1 ms. If the time between two consecutive conversions
is longer than 1 ms, for instance, after power-up, the first con­version result should be ignored. This mode makes the AD7665
ideal for applications where both high accuracy and fast sample
rate are required.

The Normal Mode is the fastest mode (500 kSPS) without any
limitation about the time between conversions. This mode makes
the AD7665 ideal for asynchronous applications such as data
acquisition systems, where both high accuracy and fast sample
rate are required.

The Impulse Mode, the lowest power dissipation mode, allows
power saving between conversions. The maximum throughput in
this mode is 444 kSPS. When operating at 100 SPS, for example,
it typically consumes only 15 µW. This feature makes the AD7665
ideal for battery-powered applications.

Transfer Functions

Using the OB/2C digital input, the AD7665 offers two output
codings: straight binary and twos complement. The ideal transfer
characteristic for the AD7665 is shown in Figure 4 and Table III.

111...111

111...110

111...101

ADC CODE – Straight Binary

000...010

000...001

000...000

FS  1 LSBFS

FS  0.5 LSB

FS  1.5 LSB

FS  1 LSB

ANALOG INPUT

Figure 4. ADC Ideal Transfer Function

REV. B

AD7665

Table III. Output Codes and Ideal Input Voltages

Digital Output
Code (Hexa)
Straight Twos

Description Analog Input Binary Complement

Full-Scale Range1±10 V ±5 V ±2.5 V 0 V to 10 V 0 V to 5 V 0 V to 2.5 V
Least Significant Bit 305.2 µV 152.6 µV 76.3 µV 152.6 µV 76.3 µV 38.15 µV
FSR – 1 LSB 9.999695 V 4.999847 V 2.499924 V 9.999847 V 4.999924 V 2.499962 V FFFF
Midscale + 1 LSB 305.2 µV 152.6 µV 76.3 µV 5.000153 V 2.570076 V 1.257038 V 8001 0001
Midscale 0 V 0 V 0 V 5 V 2.5 V 1.25 V 8000 0000
Midscale – 1 LSB –305.2 µV –152.6 µV –76.3 µV 4.999847 V 2.499924 V 1.249962 V 7FFF FFFF
–FSR + 1 LSB –9.999695 V –4.999847 V –2.499924 V 152.6 µV 76.3 µV 38.15 µV 0001 8001
–FSR –10 V –5 V –2.5 V 0 V 0 V 0 V 000038000

NOTES

1

Values with REF = 2.5 V; with REF = 3 V, all values will scale linearly.

2

This is also the code for an overrange analog input.

3

This is also the code for an underrange analog input.

TYPICAL CONNECTION DIAGRAM

Figure 5 shows a typical connection diagram for the AD7665. Different circuitry shown on this diagram is optional and is discussed below.

2

7FFF

2

3

ADR421

2.5V REF
NOTE 1

ANALOG

INPUT

(10V)

ANALOG

SUPPLY

(5V)

100nF

NOTE 3

1M

++

+

+

10F

50k

U2

+

10F

C

REF

NOTE 2

100nF

100nF

50

NOTE 7

AVDD

AGND DGND DVDD OVDD OGND

REF

REFGND

INA

10F

AD7665

100nF

AD8031

NOTE 4

50

U1

NOTE 5

+

AD8021

NOTES

1. SEE VOLTAGE REFERENCE INPUT SECTION.

2. WITH THE RECOMMENDED VOLTAGE REFERENCES, C

3. OPTIONAL CIRCUITRY FOR HARDWARE GAIN CALIBRATION.

4. FOR BIPOLAR RANGE ONLY. SEE SCALER REFERENCE INPUT SECTION.

5. THE AD8021 IS RECOMMENDED. SEE DRIVER AMPLIFIER CHOICE SECTION.

6. WITH 0V TO 2.5V RANGE ONLY. SEE ANALOG INPUTS SECTION.

7. OPTION. SEE POWER SUPPLY SECTION.

8. OPTIONAL LOW JITTER CNVST. SEE CONVERSION CONTROL SECTION.

15

2.7nF

NOTE 6

C

C

IND

INGND

INB

INC

IS 47F. SEE VOLTAGE REFERENCE INPUT SECTION.

REF

DVDD

SCLK

SDOUT

BUSY

CNVST

OB/2C

SER/PAR

WARP

IMPULSE

CS

RD

BYTESWAP

RESET

PD

100nF

+

50

NOTE 8

DVDD

10F

DIGITAL SUPPLY
(3.3V OR 5V)

SERIAL

PORT

D

C/P/DSP

CLOCK

REV. B

Figure 5. Typical Connection Diagram (±10 V Range Shown)

–13–

AD7665

Analog Inputs

The AD7665 is specified to operate with six full-scale analog input
ranges. Connections required for each of the four analog inputs,
IND, INC, INB, and INA, and the resulting full-scale ranges are
shown in Table I. The typical input impedance for each analog
input range is also shown.

Figure 6 shows a simplified analog input section of the AD7665.

The four resistors connected to the four analog inputs form a
resistive scaler that scales down and shifts the analog input range
to a common input range of 0 V to 2.5 V at the input of the
switched capacitive ADC.

AVDD

IND

INC

INB

INA

AGND

4R

4R

2R

R

R = 1.28k

R1

C

S

Figure 6. Simplified Analog Input

By connecting the four inputs INA, INB, INC, and IND to the
input signal itself, the ground, or a 2.5 V reference, other analog
input ranges can be obtained.

The diodes shown in Figure 6 provide ESD protection for the
four analog inputs. The inputs INB, INC, and IND have a high
voltage protection (–11 V to +30 V) to allow a wide input voltage
range. Care must be taken to ensure that the analog input signal
never exceeds the absolute ratings on these inputs, including
INA (0 V to 5 V). This will cause these diodes to become forward­biased and start conducting current. These diodes can handle a
forward-biased current of 120 mA maximum. For instance, when
using the 0 V to 2.5 V input range, these conditions could eventu­ally occur on the input INA when the input buffer’s (U1) supplies
are different from AVDD. In such cases, an input buffer with a
short circuit current limitation can be used to protect the part.

75

70

65

This analog input structure allows the sampling of the differential
signal between the output of the resistive scaler and INGND.
Unlike other converters, the INGND input is sampled at the same
time as the inputs. By using this differential input, small signals
common to both inputs are rejected as shown in Figure 7, which
represents the typical CMRR over frequency. For instance, by using
INGND to sense a remote signal ground, the difference of ground
potentials between the sensor and the local ADC ground is eliminated.

During the acquisition phase for ac signals, the AD7665 behaves
like a one-pole RC filter consisting of the equivalent resistance
of the resistive scaler R/2 in series with R1 and C

. The resistor

S

R1 is typically 100 W and is a lumped component made up of
some serial resistors and the on resistance of the switches. The
capacitor C

is typically 60 pF and is mainly the ADC sampling

S

capacitor. This one-pole filter with a typical –3 dB cutoff frequency
of 3.6 MHz reduces undesirable aliasing effects and limits the
noise coming from the inputs.

Except when using the 0 V to 2.5 V analog input voltage range, the
AD7665 has to be driven by a very low impedance source to avoid
gain errors. That can be done by using a driver amplifier whose
choice is eased by the primarily resistive analog input circuitry of
the AD7665.

When using the 0 V to 2.5 V analog input voltage range, the input
impedance of the AD7665 is very high so the AD7665 can be
driven directly by a low impedance source without gain error.
That allows, as shown in Figure 5, putting an external one-pole
RC filter between the output of the amplifier output and the ADC
analog inputs to even further improve the noise filtering done by
the AD7665 analog input circuit. However, the source impedance
has to be kept low because it affects the ac performances, especially
the total harmonic distortion (THD). The maximum source
impedance depends on the amount of total THD that can be
tolerated. The THD degradation is a function of the source imped­ance and the maximum input frequency as shown in Figure 8.

–70

THD

–100

–80

–90

R = 50

R = 100





R = 11



60

55

CMRR – dB

50

45

40

35

1 10 100 1000 10000

FREQUENCY – kHz

Figure 7. Analog Input CMRR vs. Frequency

–14–

–110

0 100

FREQUENCY – kHz

1000

Figure 8. THD vs. Analog Input Frequency and Input
Resistance (0 V to 2.5 V Only)

REV. B

AD7665

Driver Amplifier Choice

Although the AD7665 is easy to drive, the driver amplifier needs
to meet at least the following requirements:

∑ The driver amplifier and the AD7665 analog input circuit

must be able, together, to settle for a full-scale step the capacitor
array at a 16-bit level (0.0015%). In the amplifier’s data sheet,
the settling at 0.1% to 0.01% is more commonly specified.
It could significantly differ from the settling time at a 16-bit
level and it should therefore be verified prior to the driver
selection. The tiny op amp AD8021, which combines ultralow
noise and a high gain bandwidth, meets this settling time
requirement even when used with a high gain up to 13.

∑ The noise generated by the driver amplifier needs to be kept

as low as possible in order to preserve the SNR and transi­tion noise performance of the AD7665. The noise coming
from the driver is first scaled down by the resistive scaler
according to the analog input voltage range used and is then
filtered by the AD7665 analog input circuit one-pole, low-pass
filter made by (R/2 + R1) and C

. The SNR degradation due

S

to the amplifier is

SNR

LOSS

Ê
Á

20

log

Á
Á
Á

784

Á
Ë

=

28

.

Ne

25

Ê

p

f

+

Á

dB

3

–

2

FSR

Ë

ˆ
˜

˜
˜

2

ˆ

˜

N

˜

˜

¯

¯

where:

is the –3 dB input bandwidth in MHz of the AD7665

f

–3 dB

(3.6 MHz) or the cutoff frequency of the input filter
if any used (0 V to 2.5 V range).

N is the noise factor of the amplifier (1 if in buffer

configuration).

e

is the equivalent input noise voltage of the op amp

N

in nV/Hz

1/2

.

FSR is the full-scale span (i.e., 5 V for ±2.5 V range).

For instance, when using the 0 V to 2.5 V range, a driver
like the AD8021, with an equivalent input noise of 2 nV/÷Hz
and configured as a buffer, thus with a noise gain of 1, the
SNR degrades by only 0.12 dB.

∑ The driver needs to have a THD performance suitable to

that of the AD7665. TPC 11 gives the THD versus frequency
that the driver should preferably exceed.

The AD8021 meets these requirements and is usually appropriate
for almost all applications. The AD8021 needs an external com­pensation capacitor of 10 pF. This capacitor should have good
linearity as an NPO ceramic or mica type.

The AD8022 could also be used where a dual version is needed
and a gain of 1 is used.

The AD829 is another alternative where high frequency (above
100 kHz) performance is not required. In a gain of 1, it requires
an 82 pF compensation capacitor.

The AD8610 is another option where low bias current is needed
in low frequency applications.

Voltage Reference Input

The AD7665 uses an external 2.5 V voltage reference.

The voltage reference input REF of the AD7665 has a dynamic
input impedance; it should therefore be driven by a low impedance
source with an efficient decoupling between REF and REFGND
inputs. This decoupling depends on the choice of the voltage
reference but usually consists of a 1 µF ceramic capacitor and a
low ESR tantalum capacitor connected to the REF and REFGND
inputs with minimum parasitic inductance. 47 µF is an appropriate
value for the tantalum capacitor when used with one of the
recommended reference voltages:

∑ The low noise, low temperature drift ADR421 and AD780

voltage references

∑ The low power ADR291 voltage reference

∑ The low cost AD1582 voltage reference

For applications using multiple AD7665s, it is more effective to
buffer the reference voltage with a low noise, very stable op amp
like the AD8031.

Care should also be taken with the reference temperature coeffi­cient of the voltage reference that directly affects the full-scale
accuracy if this parameter matters. For instance, a ±15 ppm/°C
tempco of the reference changes the full scale by ±1 LSB/°C.

Note that V

, as mentioned in the Specification tables, could

REF

be increased to AVDD – 1.85 V. The benefit here is the increased
SNR obtained as a result of this increase. Since the input range
is defined in terms of V

, this would essentially increase the

REF

±REF range from ±2.5 V to ±3 V and so on with an AVDD above

4.85 V. The theoretical improvement as a result of this increase
in reference is 1.58 dB (20 log [3/2.5]). Due to the theoretical
quantization noise, however, the observed improvement is approxi­mately 1 dB. The AD780 can be selected with a 3 V reference
voltage.

Scaler Reference Input (Bipolar Input Ranges)

When using the AD7665 with bipolar input ranges, the connection
diagram in Figure 5 shows a reference buffer amplifier. This
buffer amplifier is required to isolate the REF pin from the signal
dependent current in the INx pin. A high speed op amp such as
the AD8031 can be used with a single 5 V power supply without
degrading the performance of the AD7665. The buffer must have
good settling characteristics and provide low total noise within
the input bandwidth of the AD7665.

Power Supply

The AD7665 uses three sets of power supply pins: an analog
5V supply AVDD, a digital 5 V core supply DVDD, and a digital
input/output interface supply OVDD. The OVDD supply allows
direct interface with any logic working between 2.7 V and DVDD
+ 0.3 V. To reduce the number of supplies needed, the digital
core (DVDD) can be supplied through a simple RC filter from
the analog supply as shown in Figure 5. The AD7665 is indepen­dent of power supply sequencing, once OVDD does not exceed
DVDD by more than 0.3 V, and thus free from supply voltage
induced latch-up. Additionally, it is very insensitive to power
supply variations over a wide frequency range as shown in Figure 9.

REV. B

–15–

AD7665

75

70

65

60

55

PSRR – dB

50

45

40

35

1 10 100 1000

FREQUENCY – kHz

Figure 9. PSRR vs. Frequency

POWER DISSIPATION

In Impulse Mode, the AD7665 automatically reduces its power
consumption at the end of each conversion phase. During the
acquisition phase, the operating currents are very low, which
allows significant power savings when the conversion rate is
reduced, as shown in Figure 10. This feature makes the AD7665
ideal for very low power battery applications.

100000

WARP/NORMAL

10000

W



1000

100

10

POWER DISSIPATION –

1

IMPULSE

0.1
1 10 100 1000 10000 100000 1000000

SAMPLING RATE – SPS

Figure 10. Power Dissipation vs. Sample Rate

This does not take into account the power, if any, dissipated by
the input resistive scaler, which depends on the input voltage
range used and the analog input voltage even in Power-Down
Mode. There is no power dissipated when the 0 V to 2.5 V is
used or when both the analog input voltage is 0 V and a unipolar
range, 0 V to 5 V or 0 V to 10 V, is used.

It should be noted that the digital interface remains active even
during the acquisition phase. To reduce the operating digital
supply currents even further, the digital inputs need to be driven
close to the power rails (i.e., DVDD and DGND) and OVDD
should not exceed DVDD by more than 0.3 V.

CONVERSION CONTROL

Figure 11 shows the detailed timing diagrams of the conversion
process. The AD7665 is controlled by the signal CNVST, which
initiates conversion. Once initiated, it cannot be restarted or
aborted, even by the power-down input PD, until the conversion
is complete. The CNVST signal operates independently of CS
and RD signals.

t

2

t

1

CNVST

BUSY

t

3

t

5

MODE

ACQUIRE CONVERT ACQUIRE CONVERT

t

4

t

6

t

7

t

8

Figure 11. Basic Conversion Timing

In Impulse Mode, conversions can be automatically initiated. If
CNVST is held LOW when BUSY is LOW, the AD7665 controls
the acquisition phase and then automatically initiates a new
conversion. By keeping CNVST LOW, the AD7665 keeps the
conversion process running by itself. It should be noted that the
analog input has to be settled when BUSY goes LOW. Also,
at power-up, CNVST should be brought LOW once to initiate
the conversion process. In this mode, the AD7665 could some­times run slightly faster than the guaranteed limits in the Impulse
Mode of 444 kSPS. This feature does not exist in Warp or
Normal Modes.

Although CNVST is a digital signal, it should be designed with
special care with fast, clean edges, and levels with minimum
overshoot and undershoot or ringing. It is a good thing to shield
the CNVST trace with ground and also to add a low value serial
resistor (i.e., 50 V) termination close to the output of the com­ponent that drives this line.

For applications where the SNR is critical, the CNVST signal
should have a very low jitter. To achieve this, some use a
dedicated oscillator for CNVST generation, or at least to clock
it with a high frequency low jitter clock as shown in Figure 5.

t

9

RESET

BUSY

DATA BUS

–16–

CNVST

t

8

Figure 12. RESET Timing

REV. B

AD7665

CS

BYTE

PINS D[15:8]

HI-Z

HIGH BYTE LOW BYTE

HI-Z

HI-Z

HIGH BYTE

LOW BYTE

HI-Z

t

12

t

12

t

13

RD

PINS D[7:0]

DIGITAL INTERFACE

The AD7665 has a versatile digital interface; it can be interfaced
with the host system by using either a serial or parallel interface.
The serial interface is multiplexed on the parallel data bus. The
AD7665 digital interface also accommodates both 3 V or 5 V
logic by simply connecting the OVDD supply pin of the AD7665
to the host system interface digital supply. Finally, by using the
OB/2C input pin, twos complement and straight binary coding
can be used.

The two signals CS and RD control the interface. When at least
one of these signals is HIGH, the interface outputs are in high
impedance. Usually, CS allows the selection of each AD7665 in
multicircuit applications and is held LOW in a single AD7665
design. RD is generally used to enable the conversion result on
the data bus.

CS

= RD = 0

t

1

CNVST

t

10

BUSY

DATA BUS

t

3

PREVIOUS CONVERSION DATA NEW DATA

t

4

t

11

CS = 0

t

CNVST,

RD

BUSY

DATA BUS

t

3

t

12

1

PREVIOUS

CONVERSION

t

t

4

13

Figure 15. Slave Parallel Data Timing for Reading (Read
during Convert)

The BYTESWAP pin allows a glueless interface to an 8-bit bus.
As shown in Figure 16, the LSB is output on D[7:0] and the
MSB is output on D[15:8] when BYTESWAP is LOW. When
BYTESWAP is HIGH, the LSB and MSB are swapped and the
LSB is output on D[15:8] and the MSB is output on D[7:0].
By connecting BYTESWAP to an address line, the 16 data bits
can be read in two bytes on either D[15:8] or D[7:0].

Figure 13. Master Parallel Data Timing for Reading
(Continuous Read)

PARALLEL INTERFACE

The AD7665 is configured to use the parallel interface when the
SER/PAR is held LOW. The data can be read either after each
conversion, which is during the next acquisition phase, or during
the following conversion as shown in Figures 14 and 15, respec­tively. When the data is read during the conversion, however,
it is recommended that it be read-only during the first half of the
conversion phase. That avoids any potential feedthrough between
voltage transients on the digital interface and the most critical
analog conversion circuitry.

CS

RD

BUSY

DATA BUS

t

12

CURRENT

CONVERSION

t

13

Figure 14. Slave Parallel Data Timing for Reading (Read
after Convert)

Figure 16. 8-Bit Parallel Interface

SERIAL INTERFACE

The AD7665 is configured to use the serial interface when the
SER/PAR is held HIGH. The AD7665 outputs 16 bits of data,
MSB first, on the SDOUT pin. This data is synchronized with
the 16 clock pulses provided on the SCLK pin. The output data
is valid on both the rising and falling edge of the data clock.

MASTER SERIAL INTERFACE
Internal Clock

The AD7665 is configured to generate and provide the serial data
clock SCLK when the EXT/INT pin is held LOW. It also gener­ates a SYNC signal to indicate to the host when the serial data is
valid. The serial clock SCLK and the SYNC signal can be inverted
if desired. Depending on RDC/SDIN input, the data can be
read after each conversion or during conversion. Figures 17
and 18 show the detailed timing diagrams of these two modes.

Usually, because the AD7665 is used with a fast throughput, the
mode master, read during conversion, is the most recommended
Serial Mode when it can be used.

REV. B

–17–

AD7665

CS, RD

CNVST

EXT/

= 0

INT

t

3

RDC/SDIN = 0 INVSCLK = INVSYNC = 0

BUSY

SYNC

SCLK

SDOUT

CS, RD

CNVST

BUSY

t

28

t

29

t

14

t

18

t

19

t

20

t

21

t

30

t

24

123 141516

t

15

D2 D1 D0

22

D15 D14

t

23

X

t

16

t

Figure 17. Master Serial Data Timing for Reading (Read after Convert)

EXT/

t

= 0

INT

1

t

3

RDC/SDIN = 1 INVSCLK = INVSYNC = 0

t

25

t

26

t

27

t

SYNC

SCLK

SDOUT

17

t

14

t

15

t

18

t

19

t20t

21

12 3 141516

t

24

D15 D14 D2 D1 D0X

t

16

t

22

t

23

t

25

t

26

t

27

Figure 18. Master Serial Data Timing for Reading (Read Previous Conversion during Convert)

–18–

REV. B

AD7665

CNVST

CS

SCLK

SDOUTRDC/SDIN

BUSYBUSY

DATA
OUT

AD7665

#1

(DOWNSTREAM)

BUSY
OUT

CNVST

CS

SCLK

AD7665

#2

(UPSTREAM)

RDC/SDIN SDOUT

SCLK IN

CS IN

CNVST IN

In Read-during-Conversion Mode, the serial clock and data toggle
at appropriate instants, which minimizes potential feedthrough
between digital activity and the critical conversion decisions.

In Read-after-Conversion Mode, it should be noted that unlike
in other modes, the signal BUSY returns LOW after the 16 data
bits are pulsed out and not at the end of the conversion phase,
which results in a longer BUSY width.

SLAVE SERIAL INTERFACE
External Clock

The AD7665 is configured to accept an externally supplied serial
data clock on the SCLK pin when the EXT/INT pin is held
HIGH. In this mode, several methods can be used to read the
data. The external serial clock is gated by CS and the data are
output when both CS and RD are LOW. Thus, depending on CS,
the data can be read after each conversion or during the follow­ing conversion. The external clock can be either a continuous or
discontinuous clock. A discontinuous clock can be either normally
HIGH or normally LOW when inactive. Figures 19 and 21 show
the detailed timing diagrams of these methods.

While the AD7665 is performing a bit decision, it is important
that voltage transients not occur on digital input/output pins or
degradation of the conversion result could occur. This is particu­larly important during the second half of the conversion phase
because the AD7665 provides error correction circuitry that can
correct for an improper bit decision made during the first half of
the conversion phase. For this reason, it is recommended that
when an external clock is being provided, it is a discontinuous clock
that is toggling only when BUSY is LOW or, more importantly,
that does not transition during the latter half of BUSY HIGH.

External Discontinuous Clock Data Read after Conversion

Though the maximum throughput cannot be achieved using this
mode, it is the most recommended of the serial slave modes.
Figure 19 shows the detailed timing diagrams of this method.
After a conversion is complete, indicated by BUSY returning
LOW, the result of this conversion can be read while both CS
and RD are LOW. The data is shifted out, MSB first, with

CS

BUSY

SCLK

SDOUT

SDIN

Figure 19. Slave Serial Data Timing for Reading (Read after Convert)

EXT/INT = 1

t

35

t36 t

37

123 1415161718

t

31

X

D15 D14 D1

t

16

t

33

t

32

D13

t

34

X15 X14 X13 X1 X0 Y15 Y14

INVSCLK = 0

RD = 0

D0

X15 X14

16 clock pulses and is valid on both the rising and falling edge
of the clock.

Among the advantages of this method, the conversion performance
is not degraded because there are no voltage transients on the
digital interface during the conversion process.

Another advantage is to be able to read the data at any speed up
to 40 MHz, which accommodates both slow digital host interface
and the fastest serial reading.

Finally, in this mode only, the AD7665 provides a “daisy-chain”
feature using the RDC/SDIN input pin for cascading multiple
converters together. This feature is useful for reducing component
count and wiring connections when desired as, for instance, in
isolated multiconverter applications.

An example of the concatenation of two devices is shown in
Figure 20. Simultaneous sampling is possible by using a com­mon CNVST signal. It should be noted that the RDC/SDIN
input is latched on the opposite edge of SCLK of the one used
to shift out the data on SDOUT. Therefore, the MSB of the
“upstream” converter just follows the LSB of the “downstream”
converter on the next SCLK cycle.

Figure 20. Two AD7665s in a Daisy-Chain Configuration

REV. B

–19–

AD7665

INVSCLK = 0

CS, RD

CNVST

BUSY

SCLK

SDOUT

EXT/INT = 1

t

3

t

16

t

35

t

t

36

37

12 3 141516

t

31

t

32

Figure 21. Slave Serial Data Timing for Reading (Read Previous Conversion during Convert)

External Clock Data Read during Conversion

Figure 21 shows the detailed timing diagrams of this method. Dur­ing a conversion, while both CS and RD are LOW, the result of
the previous conversion can be read. The data is shifted out, MSB
first, with 16 clock pulses and is valid on both the rising and
falling edge of the clock. The 16 bits have to be read before the
current conversion is complete. If that is not done, RDERROR
is pulsed HIGH and can be used to interrupt the host interface to
prevent incomplete data reading. There is no daisy-chain feature
in this mode, and RDC/SDIN input should always be tied either
HIGH or LOW.

To reduce performance degradation due to digital activity, a fast
discontinuous clock, at least 25 MHz when Impulse Mode is
used or 40 MHz when Normal or Warp Mode is used, is recom­mended to ensure that all the bits are read during the first half
of the conversion phase. It is also possible to begin to read the
data after conversion and continue to read the last bits even after
a new conversion has been initiated. That allows the use of a slower
clock speed like 10 MHz in Impulse Mode, 12 MHz in Normal
Mode, and 15 MHz in Warp Mode.

RD = 0

D1 D0X D15 D14 D13

necessary, could be initiated in response to the end-of-conversion
signal (BUSY going LOW) using an interrupt line of the micro­controller. The serial peripheral interface (SPI) on the MC68HC11
is configured for Master Mode (MSTR) = 1, Clock Polarity Bit
(CPOL) = 0, Clock Phase Bit (CPHA) = 1, and SPI interrupt
enable (SPIE) = 1 by writing to the SPI Control Register (SPCR).
The IRQ is configured for edge-sensitive-only operation
(IRQE = 1 in OPTION register).

DVDD

AD7665

*

SER/PAR
EXT/INT

CS
RD

INVSCLK

*ADDITIONAL PINS OMITTED FOR CLARITY

BUSY

SDOUT

SCLK

CNVST

MC68HC11*

IRQ

MISO/SDI

SCK

I/O PORT

Figure 22. Interfacing the AD7665 to SPI Interface

MICROPROCESSOR INTERFACING

The AD7665 is ideally suited for traditional dc measurement
applications supporting a microprocessor and ac signal processing
applications interfacing to a digital signal processor. The AD7665
is designed to interface with either a parallel 8-bit or 16-bit wide
interface or with a general-purpose Serial Port or I/O Ports on a
microcontroller. A variety of external buffers can be used with
the AD7665 to prevent digital noise from coupling into the ADC.
The following sections illustrate the use of the AD7665 with
an SPI-equipped microcontroller, the ADSP-21065L and
ADSP-218x signal processors.

SPI Interface (MC68HC11)

Figure 22 shows an interface diagram between the AD7665 and
an SPI-equipped microcontroller, such as the MC68HC11. To
accommodate the slower speed of the microcontroller, the
AD7665 acts as a slave device and data must be read after conver­sion. This mode also allows the daisy-chain feature. The convert
command could be initiated in response to an internal timer
interrupt. The reading of output data, one byte at a time, if

–20–

ADSP-21065L in Master Serial Interface

As shown in Figure 23, the AD7665 can be interfaced to the
ADSP-21065L using the serial interface in Master Mode without
any glue logic required. This mode combines the advantages of
reducing the wire connections and the ability to read the data during
or after conversion at maximum speed transfer (DIVSCLK[0:1]
both low).

The AD7665 is configured for the Internal Clock Mode
(EXT/INT LOW) and acts therefore as the master device. The
convert command can be generated by either an external low jitter
oscillator or, as shown, by a FLAG output of the ADSP-21065L
or by a frame output TFS of one Serial Port of the ADSP-21065L
that can be used like a timer. The Serial Port on the ADSP­21065L is configured for external clock (IRFS = 0), rising edge
active (CKRE = 1), external late framed sync signals (IRFS = 0,
LAFS = 1, RFSR = 1), and active HIGH (LRFS = 0). The Serial
Port of the ADSP-21065L is configured by writing to its receive
control register (SRCTL)—see ADSP-2106x SHARC User’s
Manual. Because the Serial Port within the ADSP-21065L will

REV. B

AD7665

be seeing a discontinuous clock, an initial word reading has to be
done after the ADSP-21065L has been reset to ensure that the
Serial Port is properly synchronized to this clock during each
following data read operation.

DVDD

AD7665

*

SER/PAR

RDC/SDIN

RD
EXT/INT
CS

INVSYNC

INVSCLK

*ADDITIONAL PINS OMITTED FOR CLARITY

SYNC

SDOUT

SCLK

CNVST

ADSP-21065L*

SHARC

RFS

DR

RCLK

FLAG OR TFS

Figure 23. Interfacing to the ADSP-21065L Using the
Serial Master Mode

APPLICATION HINTS
Layout

The AD7665 has very good immunity to noise on the power
supplies as can be seen in Figure 9. However, care should still
be taken with regard to grounding layout.

The printed circuit board that houses the AD7665 should be
designed so the analog and digital sections are separated and con­fined to certain areas of the board. This facilitates the use of ground
planes that can be easily separated. Digital and analog ground
planes should be joined in only one place, preferably underneath
the AD7665, or at least as close as possible to the AD7665. If the
AD7665 is in a system where multiple devices require analog-to­digital ground connections, the connection should still be made
at one point only, a star ground point that should be established
as close as possible to the AD7665.

It is recommended to avoid running digital lines under the device
as these will couple noise onto the die. The analog ground plane
should be allowed to run under the AD7665 to avoid noise
coupling. Fast switching signals like CNVST or clocks should
be shielded with digital ground to avoid radiating noise to other
sections of the board and should never run near analog signal
paths. Crossover of digital and analog signals should be avoided.
Traces on different but close layers of the board should run at right

angles to each other. This will reduce the effect of feedthrough
through the board.

The power supply lines to the AD7665 should use as large a trace
as possible to provide low impedance paths and reduce the effect
of glitches on the power supply lines. Good decoupling is also
important to lower the supplies impedance presented to the
AD7665 and to reduce the magnitude of the supply spikes. Decou­pling ceramic capacitors, typically 100 nF, should be placed on all
of the power supply pins AVDD, DVDD, and OVDD close to and
ideally right up against these pins and their corresponding ground
pins. Additionally, low ESR 10 µF capacitors should be located
in the vicinity of the ADC to further reduce low frequency ripple.

The DVDD supply of the AD7665 can be either a separate supply
or come from the analog supply, AVDD, or from the digital inter­face supply, OVDD. When the system digital supply is noisy, or
fast switching digital signals are present, it is recommended, if
no separate supply is available, to connect the DVDD digital
supply to the analog supply AVDD through an RC filter as shown
in Figure 5 and to connect the system supply to the interface
digital supply OVDD and the remaining digital circuitry. When
DVDD is powered from the system supply, it is useful to insert
a bead to further reduce high frequency spikes.

The AD7665 has five different ground pins: INGND, REFGND,
AGND, DGND, and OGND. INGND is used to sense the analog
input signal. REFGND senses the reference voltage and should
be a low impedance return to the reference because it carries
pulsed currents. AGND is the ground to which most internal ADC
analog signals are referenced. This ground must be connected
with the least resistance to the analog ground plane. DGND must
be tied to the analog or digital ground plane depending on the
configuration. OGND is connected to the digital system ground.

The layout of the decoupling of the reference voltage is important.
The decoupling capacitor should be close to the ADC and
connected with short and large traces to minimize parasitic
inductances.

Evaluating the AD7665 Performance

A recommended layout for the AD7665 is outlined in the evalua­tion board for the AD7665. The evaluation board package includes
a fully assembled and tested evaluation board, documentation,
and software for controlling the board from a PC via the Eval­Control Board.

REV. B

–21–

AD7665

OUTLINE DIMENSIONS

48-Lead Low Profile Quad Flat Package [LQFP]

(ST-48)

Dimensions shown in millimeters

1.45

1.40

1.35

0.15

0.05

PIN 1
INDICATOR

10

6
2

SEATING
PLANE

ROTATED 90 CCW

VIEW A

0.10 MAX
COPLANARITY

0.75

0.60

0.45

SEATING

PLANE

0.20

0.09

7

3.5
0

COMPLIANT TO JEDEC STANDARDS MS-026BBC

1.60
MAX

VIEW A

1

12

0.50

BSC

48

13

9.00 BSC

PIN 1

TOP VIEW

(PINS DOWN)

48-Lead Lead Frame Chip Scale Package [LFCSP]

(CP-48)

Dimensions shown in millimeters

7.00

BSC SQ

0.60 MAX

37

36

0.60 MAX

SQ

0.30

0.23

0.18

37

36

7.00

BSC SQ

25

24

0.27

0.22

0.17

PIN 1

48

INDICATOR

1

1.00

0.90

0.80

0.20
REF

12 MAX

SEATING
PLANE

TOP

VIEW

0.80 MAX

0.65 NOM

0.50 BSC

COMPLIANT TO JEDEC STANDARDS MO-220-VKKD-2

6.75

BSC SQ

0.50

0.40

0.30

0.05 MAX

0.02 NOM

COPLANARITY

0.08

BOTTOM

VIEW

25

24

5.50
REF

13

5.25
SQ

5.10

4.95

12

PADDLE CONNECTED TO AGND.
THIS CONNECTION IS NOT
REQUIRED TO MEET THE
ELECTRICAL PERFORMANCES

–22–

REV. B

AD7665

Revision History

Location Page

4/03—Data Sheet changed from REV. A to REV. B.

Changes to PulSAR Selection table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Changes to ORDERING GUIDE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Change to Figure 5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Updated OUTLINE DIMENSIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

5/02—Data Sheet changed from REV. 0 to REV. A.

Edits to FEATURES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Edit to GENERAL DESCRIPTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Chart added to PRODUCT HIGHLIGHTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Edits to SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2–3

Edits to Table I . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Edits to ABSOLUTE MAXIMUM RATINGS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Edits to ORDERING GUIDE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Edits to PIN FUNCTION DESCRIPTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Addition of TPC I6 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Edits to CIRCUIT INFORMATION section . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Edits to Table III . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

New Voltage Reference Input section . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Edits to ADSP-21065L in Master Serial Interface section . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

New ST-48 Package Outline . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

REV. B

–23–

C01846–0–5/03(B)

–24–