Datasheet AD73411 Datasheet (Analog Devices)

Page 1

Low-Power

Analog Front End with DSP Microcomputer

FEATURES

AFE PERFORMANCE 16-Bit A/D Converter 16-Bit D/A Converter Programmable Input/Output Sample Rates 76 dB ADC SNR 77 dB DAC SNR 64 kS/s Maximum Sample Rate –90 dB Crosstalk Low Group Delay (25 ␮s Typ per ADC Channel,

50 ␮s Typ per DAC Channel) Programmable Input/Output Gain On-Chip Reference

DSP PERFORMANCE 19 ns Instruction Cycle Time @ 3.3 V, 52 MIPS

Sustained Performance AD73411-80

80K Bytes of On-Chip RAM, Conﬁgured as 16K Words

Program Memory RAM and 16K Words

Data Memory RAM AD73411-40

40K Bytes of On-Chip RAM, Conﬁgured as 8K Words

Program Memory RAM and 8K Words

Data Memory RAM

DATA

ADDRESS

GENERATORS

DAG 2

DAG 1

ARITHMETIC UNITS

ADSP-2100 BASE

ARCHITECTURE

AD73411

FUNCTIONAL BLOCK DIAGRAM

POWER-DOWN

CONTROL

PROGRAM

SEQUENCER

PROGRAM MEMORY ADDRESS

DATA MEMORY ADDRESS

PROGRAM MEMORY DATA

DATA MEMORY DATA

SHIFTERMACALU

REF

MEMORY

16K PM

(OPTIONAL

8K)

SERIAL PORTS

SPORT 0

SPORT 1

SERIAL PORT

SPORT 2

ADC DAC

ANALOG FRONT END

SECTION

16K DM

8K)

PROGRAMMABLE

I/O

AND

FLAGS

TIMER

FULL MEMORY

MODE

EXTERNAL

ADDRESS

BUS

EXTERNAL

DATA

BUS

BYTE DMA

CONTROLLER

EXTERNAL

DATA

BUS

INTERNAL

DMA

PORT

HOST MODE

GENERAL DESCRIPTION

The AD73411 is a single device incorporating a single analog front end (AFE) and a microcomputer optimized for digital signal processing (DSP) and other high-speed numeric processing applications.

The AD73411’s analog front end (AFE) section is suitable for general-purpose applications including speech and telephony. The AFE section features a 16-bit A/D converter and a 16-bit D/A converter. Each converter provides 76 dB signal-to-noise ratio over a voiceband signal bandwidth.

The AD73411 is particularly suitable for a variety of applications in the speech and telephony area, including low bit rate, highquality compression, speech enhancement, recognition, and synthesis. The low group delay characteristic of the AFE makes it suitable for single or multichannel active control applications. The A/D and D/A conversion channels feature programmable input/output gains with ranges of 38 dB and 21 dB respectively. An on-chip reference voltage is included to allow single supply operation.

REV. 0

Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Analog Devices.

The sampling rate of the AFE is programmable with four separate settings offering 64, 32, 16, and 8 kHz sampling rates (from a master clock of 16.384 MHz) while the serial port (SPORT2) allows easy expansion of the number of I/O channels by cascading extra AFEs external to the AD73411.

The AD73411’s DSP engine combines the ADSP-2100 family base architecture (three computational units, data address generators, and a program sequencer) with two serial ports, a 16-bit internal DMA port, a byte DMA port, a programmable timer, Flag I/O, extensive interrupt capabilities, and on-chip program and data memory.

The AD73411-80 integrates 80K bytes of on-chip memory conﬁgured as 16K words (24-bit) of program RAM, and 16K words (16-bit) of data RAM. The AD73411-40 integrates 40K bytes of on-chip memory conﬁgured as 8K words (24bit) of program RAM, and 8K words (16-bit) of data RAM. Power-down circuitry is also provided to meet the low power needs of battery-operated portable equipment. The AD73411 is available in a 119-ball PBGA package.

One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A. Tel: 781/329-4700 World Wide Web Site: http://www.analog.com Fax: 781/326-8703 © Analog Devices, Inc., 2000

Page 2

AD73411–SPECIFICATIONS

(AVDD = DVDD = 3.0 V to 3.6 V; DGND = AGND = 0 V, f

= 64 kHz; TA = T

SAMP

MIN

to T

, unless otherwise noted.)

MAX

= 16.384 MHz,

MCLK

Parameter Min Typ Max Unit Test Conditions/Comments

AFE SECTION

REFERENCE

REFCAP

Absolute Voltage, V

REFCAP

1.08 1.2 1.32 V

REFCAP TC 50 ppm/°C 0.1 µF Capacitor Required from

REFOUT REFCAP to AGND2

Typical Output Impedance 145 Ω

Absolute Voltage, V

REFOUT

ADC SPECIFICATIONS

Maximum Input Range at VIN

2, 3

1.08 1.2 1.32 V Unloaded

1.578 V p-p Measured Differentially –2.85 dBm Max Input = (1.578/1.2) × V

REFCAP

Nominal Reference Level at VIN 1.0954 V p-p Measured Differentially

(0 dBm0) –6.02 dBm

Absolute Gain

PGA = 0 dB –2.2 –0.6 +1.0 dB 1.0 kHz, 0 dBm0

PGA = 38 dB –1.0 dB 1.0 kHz, 0 dBm0 Gain Tracking Error ± 0.1 dB 1.0 kHz, +3 dBm0 to –50 dBm0 Signal to (Noise + Distortion) Refer to Figure ?

PGA = 0 dB 71 76 dB 300 Hz to 3400 Hz;

70 74 dB 0 Hz to f

72 dB 300 Hz to 3400 Hz; f 56 dB 0 Hz to f

SAMP

/2; f

SAMP

= 64 kHz

PGA = 38 dB 60 dB 300 Hz to 3400 Hz;

59 dB 0 Hz to f

SAMP

Total Harmonic Distortion

PGA = 0 dB –85 –75 dB 300 Hz to 3400 Hz

PGA = 38 dB –85 dB 300 Hz to 3400 Hz Intermodulation Distortion –82 dB PGA = 0 dB Idle Channel Noise –76 dBm0 PGA = 0 dB Crosstalk –100 dB ADC Input Signal Level: 1.0 kHz, 0 dBm0

DAC Input at Idle DC Offset –20 +2 +25 mV PGA = 0 dB Power Supply Rejection –84 dB Input Signal Level at AVDD and DVDD

Group Delay Input Resistance at PGA

4, 5

2, 4, 6

DAC SPECIFICATIONS

Maximum Voltage Output Swing

25 µsf 45 kΩ DMCLK = 16.384 MHz

Pins 1.0 kHz, 100 mV p-p Sine Wave

= 64 kHz

SAMP

Single-Ended 1.578 V p-p PGA = 6 dB

–2.85 dBm Max Output = (1.578/1.2) × V

REFCAP

Differential 3.156 V p-p PGA = 6 dB

3.17 dBm Max Output = 2 × ((1.578/1.2) × V

REFCAP

Nominal Voltage Output Swing (0 dBm0)

Single-Ended 1.0954 V p-p PGA = 6 dB

–6.02 dBm

Differential 2.1909 V p-p PGA = 6 dB

0 dBm

Output Bias Voltage

1.08 1.2 1.32 V REFOUT Unloaded Absolute Gain –1.8 –0.7 +0.4 dB 1.0 kHz, 0 dBm0; Unloaded Gain Tracking Error ± 0.1 dB 1.0 kHz, +3 dBm0 to –50 dBm0 Signal to (Noise + Distortion)

PGA = 0 dB 70 77 dB 300 Hz to 3400 Hz

76 dB 300 Hz to 3400 Hz; f

SAMP

= 64 kHz

PGA = 6 dB 77 dB 300 Hz to 3400 Hz

77 dB 300 Hz to 3400 Hz; f

SAMP

= 64 kHz

Total Harmonic Distortion at 0 dBm0

PGA = 0 dB –80 –70 dB

PGA = 6 dB –80 dB Intermodulation Distortion –76 dB PGA = 0 dB Idle Channel Noise –82 dBm0 PGA = 0 dB Crosstalk –100 dB ADC Input Signal Level: AGND; DAC

Output Signal Level: 1.0 kHz, 0 dBm0

–2–

REV. 0

Page 3

AD73411

Parameter Min Typ Max Unit Test Conditions/Comments

DAC SPECIFICATIONS (Continued)

Power Supply Rejection –81 dB Input Signal Level at AVDD and DVDD

Group Delay

Output DC Offset

4, 5

2, 7

25 µsf 50 µsf

–30 +5 +50 mV PGA = 6 dB

LOGIC INPUTS

, Input High Voltage DVDD – 0.8 DVDD V

INH

, Input Low Voltage 0 0.8 V

INL

IIH, Input Current –10 +10 µA

LOGIC OUTPUT

VOH, Output High Voltage DVDD – 0.4 DVDD V |IOUT| ≤ 100 µA

, Output Low Voltage 0 0.4 V |IOUT| ≤ 100 µA

Three-State Leakage Current –10 +10 µA

POWER SUPPLIES

AVDD 3.0 3.6 V DVDD 3.0 3.6 V

NOTES

Operating temperature range is as follows: –20°C to +85°C. Therefore, T

Test conditions: Input PGA set for 0 dB gain, Output PGA set for 6 dB gain, no load on analog outputs (unless otherwise noted).

At input to sigma-delta modulator of ADC.

Guaranteed by design.

Overall group delay will be affected by the sample rate and the external digital ﬁltering.

The ADC’s input impedance is inversely proportional to DMCLK and is approximated by: (3.3 × 1011)/DMCLK.

Between VOUTP and VOUTN.

At VOUT output.

Test Conditions: no load on digital inputs, analog inputs ac-coupled to ground, no load on analog outputs.

Speciﬁcations subject to change without notice.

= –20°C and T

MIN

= +85°C.

MAX

Pins: 1.0 kHz, 100 mV p-p Sine Wave

= 64 kHz; Interpolator Bypassed

SAMP

= 64 kHz

SAMP

See Table I

REV. 0

–3–

Page 4

AD73411–SPECIFICATIONS

(AVDD = DVDD = VDD = 3.0 V to 3.6 V; DGND = AGND = 0 V, f f

= 64 kHz; TA = T

SAMP

MIN

to T

, unless otherwise noted.)

MAX

= 16.384 MHz,

MCLK

Parameter Test Conditions Min Typ Max Unit

DSP SECTION V

OZH

OZL

NOTES

Bidirectional pins: D0–D23, RFS0, RFS1, SCLK0, SCLK1, TFS0, TFS1, A1–A13, PF0–PF7.

Input only pins: RESET, BR, DR0, DR1, PWD.

Input only pins: CLKIN, RESET, BR, DR0, DR1, PWD.

Output pins: BG, PMS, DMS, BMS, IOMS, CMS, RD, WR, PWDACK, A0, DT0, DT1, CLKOUT, FL2–0, BGH.

Although speciﬁed for TTL outputs, all AD73411 outputs are CMOS-compatible and will drive to VDD and GND, assuming no dc loads.

Guaranteed but not tested.

Three-statable pins: A0–A13, D0–D23, PMS, DMS, BMS, IOMS, CMS, RD, WR, DT0, DT1, SCLK0, SCLK1, TFS0, TFS1, RFS0, RFS1, PF0–PF7.

0 V on BR.

Idle refers to AD73411 state of operation during execution of IDLE instruction. Deasserted pins are driven to either VDD or GND.

VIN = 0 V and 3 V. For typical ﬁgures for supply currents, refer to Power Dissipation section.

IDD measurement taken with all instructions executing from internal memory. 50% of the instructions are multifunction (Types 1, 4, 5, 12, 13, 14), 30% are Type 2 and Type 6, and 20% are idle instructions.

Applies to PBGA package type.

Output pin capacitance is the capacitive load for any three-stated output pin.

Speciﬁcations subject to change without notice.

Hi-Level Input Voltage Hi-Level CLKIN Voltage @ VDD = max 2.2 V Lo-Level Input Voltage Hi-Level Output Voltage

Lo-Level Output Voltage

Hi-Level Input Current

Lo-Level Input Current

Three-State Leakage Current

Supply Current (Idle)

Supply Current (Dynamic)

Input Pin Capacitance

Output Pin Capacitance

1, 2

1, 3

1, 4, 5

3, 6, 12

6, 7, 12, 13

@ VDD = max 2.0 V

@ VDD = min 0.8 V @ VDD = min I

= –0.5 mA 2.4 V

@ VDD = min

= –100 µA

VDD – 0.3 V @ VDD = min I

= 2 mA 0.4 V

@ VDD = max V

= VDD max 10 µA

@ VDD = max

= 0 V 10 µA

@ VDD = max V

= VDD max

@ VDD = max V

@ VDD = 3.3 t

= 0 V

= 19 ns = 25 ns = 30 ns

@ VDD = 3.3 T

= 25°C

AMB

= 19 ns

= 25 ns

= 30 ns

10 µA

12 mA 11 mA 10 mA

45 mA 43 mA 36 mA

@ VIN = 2.5 V

= 1.0 MHz

= 25°C8pF

AMB

@ VIN = 2.5 V

= 1.0 MHz

= 25°C8pF

AMB

–4–

REV. 0

Page 5

AD73411

POWER CONSUMPTION

Parameter Typ Max SE MCLK On Test Conditions

AFE SECTION

ADC Only On 7 8 1 Yes REFOUT Disabled ADC and DAC On 11 12.5 1 Yes REFOUT Disabled REFCAP Only On 0.65 1.00 0 No REFOUT Disabled REFCAP and 2.7 3.8 0 No

REFOUT Only On All AFE Sections Off 0.6 0.75 0 Yes MCLK Active Levels Equal to 0 V and DVDD All AFE Sections Off 5 µA 30 µA 0 No Digital Inputs Static and Equal to 0 V or DVDD

DSP SECTION

Idle Mode 6.4 Dynamic 43

NOTES The above values are in mA and are typical values unless otherwise noted. Speciﬁcations subject to change without notice.

TIMING CHARACTERISTICS–AFE SECTION

Parameter Limit Unit Description

Clock Signals See Figure 1

Serial Port See Figures ? and ?

Speciﬁcations subject to change without notice.

61 ns min 16.384 MHz AMCLK Period

24.4 ns min MCLK Width High

24.4 ns min MCLK Width Low

0.4 × t

ns min SCLK Period (SCLK = AMCLK) ns min SCLK Width High

ns min SCLK Width Low 20 ns min SDI/SDIFS Setup Before SCLK Low 0 ns min SDI/SDIFS Hold After SCLK Low 10 ns max SDOFS Delay from SCLK High 10 ns min SDOFS Hold After SCLK High 10 ns min SDO Hold After SCLK High 10 ns max SDO Delay from SCLK High 30 ns max SCLK Delay from MCLK

REV. 0

–5–

Page 6

AD73411

WARNING!

ESD SENSITIVE DEVICE

ABSOLUTE MAXIMUM RATINGS*

(TA = +25°C unless otherwise noted)

AVDD, DVDD to GND . . . . . . . . . . . . . . . . –0.3 V to +4.6 V

AGND to DGND . . . . . . . . . . . . . . . . . . . . . –0.3 V to +0.3 V

Digital I/O Voltage to DGND . . . . . –0.3 V to DVDD + 0.3 V

Analog I/O Voltage to AGND . . . . . –0.3 V to AVDD + 0.3 V

Operating Temperature Range

Industrial (B Version) . . . . . . . . . . . . . . . . –20°C to +85°C

Reflow Soldering

Maximum Temperature . . . . . . . . . . . . . . . . . . . . . . . 225°C

Time at Maximum Temperature . . . . . . . . . . . . . . . . .15 sec

Maximum Temperature Ramp Rate . . . . . . . . . . . . 1.3°C/sec

*Stresses above those listed under Absolute Maximum Ratings may cause perma-

nent damage to the device. This is a stress rating only; functional operation of the device at these or any other conditions above those listed in the operational sections of this speciﬁcation is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability.

Storage Temperature Range . . . . . . . . . . . . –40°C to +125°C

Maximum Junction Temperature . . . . . . . . . . . . . . . . . 150°C

PBGA, θ

Thermal Impedance . . . . . . . . . . . . . . . . . 25°C/W

ORDERING GUIDE

Temperature Package Package

Model Range Description Option

AD73411BB-80 –20°C to +85°C 119-Ball Plastic Ball Grid Array B-119 AD73411BB-40 –20°C to +85°C 119-Ball Plastic Ball Grid Array B-119

CAUTION

ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily accumulate on the human body and test equipment and can discharge without detection. Although the AD73411 features proprietary ESD protection circuitry, permanent damage may occur on devices subjected to high energy electrostatic discharges. Therefore, proper ESD precautions are recommended to avoid performance degradation or loss of functionality.

PBGA BALL CONFIGURATION

IRQE/ PF4

IRQL0/ PF5 PMS WR

IRQL1/ PF6 IOMS RD

IRQ2/ PF7 CMS BMS

DT0 TFS0 RFS0 A3/ IAD2 A2/ IAD1 A1/IAD0 A0

DR0 SCLK0 DT1/F0 PWDACK

TFS1/IRQ1 RFS1/IRQ0

SCLK1

EMS

ELOUT ELIN

BG D3 /IACK

EBG

EBR

SDO SDOFS SDIFS SDI SE REFCAP REFOUT

VINP NC

AGND

NOTES: VDD (INT) – DSP CORE SUPPLY VDD (EXT) – DSP I/O DRIVER SUPPLY BOTH VDD (INT) AND VDD (EXT) SHOULD BE POWERED FROM THE SAME SUPPLY.

DMS

ERESET RESET

EE ECLK D23 D22 D21 D20

D2/ IAD15

D1/IAD14 VDD (INT)

D0/ IAD13 DVDD DGND

AVDD NC NC VOUTP VOUTN NC

VDD (INT) CLKIN A11/IAD10 A7/ IAD6 A4/ IAD3

DR1/FI GND

EINT

D5/ IAL D8 D9 D12 D15

D4/ IS D7/ IWR

VINN NC NC NC NC

XTAL A12/ IAD11 A8/IAD7 A5 /IAD4

VDD (EXT) A13/ IAD12 A9/ IAD8 GND

CLKOUT GND A10 /IAD9 A6/ IAD5

PF3 FL0 FL1 FL2

D19 D18 D17 D16

D6/ IRD

TOP VIEW

BGH

PWD

VDD (EXT) D11 D14

GND D10 D13

ARESET

MODE A /PF0 MODE B /PF1

VDD (EXT) MODE C /PF2

SCLK2 AMCLK

–6–

REV. 0

Page 7

AD73411

PBGA BALL FUNCTION DESCRIPTIONS

BGA

Mnemonic Location Function

VINP T1 This pin allows direct access to the positive input of the sigma-delta modulator. VINN T3 This pin allows direct access to the negative input of the sigma-delta modulator. REFOUT R7 Buffered Reference Output, which has a nominal value of 1.2 V. REFCAP R6 A Bypass Capacitor to AGND of 0.1 µF is required for the on-chip reference. The capacitor should be

ﬁxed to this pin. DGND P4 AFE Digital Ground/Substrate Connection. DVDD P3 AFE Digital Power Supply Connection. ARESET P5 Active Low Reset Signal. This input resets the entire analog front end, resetting the control registers and

clearing the digital circuitry. SCLK2 P6 Output Serial Clock whose rate determines the serial transfer rate to/from the codec. It is used to clock data

or control information to and from the serial port (SPORT2). The frequency of SCLK is equal to the

frequency of the master clock (AMCLK) divided by an integer number—this integer number being the product

of the external master clock rate divider and the serial clock rate divider. AMCLK P7 AFE Master Clock Input. AMCLK is driven from an external clock signal. If it is required to run the DSP

and AFE sections from a common clock crystal, AMCLK should be connected to the XTAL pin of the

DSP section. SDO R1 Serial Data Output of the Codec. Both data and control information may be output on this pin and is clocked on

the positive edge of SCLK. SDO is in three-state when no information is being transmitted and when SE is low. SDOFS R2 Framing Signal Output for SDO Serial Transfers. The frame sync is one bit wide and is active one SCLK

period before the ﬁrst bit (MSB) of each output word. SDOFS is referenced to the positive edge of SCLK.

SDOFS is in three-state when SE is low. SDIFS R3 Framing Signal Input for SDI Serial Transfers. The frame sync is one bit wide and is valid one SCLK

period before the ﬁrst bit (MSB) of each input word. SDIFS is sampled on the negative edge of SCLK and

is ignored when SE is low. SDI R4 Serial Data Input of the Codec. Both data and control information may be input on this pin and are clocked

on the negative edge of SCLK. SDI is ignored when SE is low. SE R5 SPORT2 Enable. Asynchronous input enable pin for SPORT2. When SE is set low by the DSP, the output

pins of SPORT2 are three-stated and the input pins are ignored. SCLK2 is also disabled internally in order

to decrease power dissipation. When SE is brought high, the control and data registers of SPORT2 are at

their original values (before SE was brought low), however the timing counters and other internal regis-

ters are at their reset values. AGND U1 AFE Analog Ground/Substrate Connection. AVDD U2 AFE Analog Power Supply Connection. VOUTP U5 Analog Output from the Positive Terminal of the Output. VOUTN U6 Analog Output from the Negative Terminal of the Output.

RESET H3 (Input) Processor Reset Input. BR N1 (Input) Bus Request Input. BG L1 (Output) Bus Grant Output. BGH F5 (Output) Bus Grant Hung Output. DMS A2 (Output) Data Memory Select Output. PMS B2 (Output) Program Memory Select Output. IOMS C2 (Output) Memory Select Output. BMS D3 (Output) Byte Memory Select Output. CMS D2 (Output) Combined Memory Select Output. RD C3 (Output) Memory Read Enable Output. WR B3 (Output) Memory Write Enable Output. IRQ2/ (Input) Edge- or Level-Sensitive Interrupt Request

PF7 D1 (Input/Output)

IRQL1/ (Input) Level-Sensitive Interrupt Requests

PF6 C1 (Input/Output) Programmable I/O Pin.

Programmable I/O Pin.

REV. 0

–7–

Page 8

AD73411

PBGA BALL FUNCTION DESCRIPTIONS (Continued)

Mnemonic Location Function

BGA

IRQL0/ (Input) Level-Sensitive Interrupt Requests PF5 B1 (Input/Output) Programmable I/O Pin. IRQE/ (Input) Edge-Sensitive Interrupt Requests

PF4 A1 (Input/Output) Programmable I/O Pin. PF3 H4 (Input/Output) Programmable I/O Pin During Normal Operation.

Mode C/ (Input) Mode Select Input—Checked Only During RESET. PF2 G7 (Input/Output) Programmable I/O Pin During Normal Operation. Mode B/ (Input) Mode Select Input—Checked Only During RESET . PF1 F7 (Input/Output) Programmable I/O Pin During Normal Operation. Mode A/ (Input) Mode Select Input—Checked Only During RESET. PF0 F6 (Input/Output) Programmable I/O Pin During Normal Operation. CLKIN A4 (Inputs) Clock or Quartz Crystal Input. The CLKIN input cannot be halted or changed during operation XTAL B4 nor operated below 10 MHz during normal operation. CLKOUT D4 (Output) Processor Clock Output. SPORT0

TFS0 E2 (Input/Output) SPORT0 Transmit Frame Sync. RFS0 E3 (Input/Output) SPORT0 Receive Frame Sync. DT0 E1 (Output) SPORT0 Transmit Data. DR0 F1 (Input) SPORT0 Receive Data. SCLK0 F2 (Input/Output) SPORT0 Serial Clock.

SPORT1

TFS1/ (Input/Output) SPORT1 Transmit Frame Sync. IRQ1 G1 (Input) Edge or Level Sensitive Interrupt. RFS1 (Input/Output) SPORT1 Receive Frame Sync. IRQ0 G2 (Input) Edge or Level Sensitive Interrupt. DT1/ (Output) SPORT1 Transmit Data. FO F3 (Output) Flag Out DR1/ (Input) SPORT1 Receive Data. FI G3 (Input) Flag In

SCLK1 H1 (Input/Output) SPORT1 Serial Clock. FL0 H5 (Output) Flag 0. FL1 H6 (Output) Flag 1. FL2 H7 (Output) Flag 2. VDD(INT) A3 (Input) DSP Core Supply.

VDD(EXT) C4 (Input) DSP I/O Interface Supply.

G6 M5

GND C7 DSP Ground.

D5 G4 N5

EZ-ICE Port

ERESET H2

EMS J1

EE J2

ECLK J3

ELOUT K1

ELIN K2

EINT K3

EBR P1

EBG M1

ddress Bus A0–E7; A1/IAD0–E6; A2/IAD1–E5; A3/IAD2–E4; A4/IAD3–A7; A5/IAD4–B7; A6/IAD5–D7; A7/IAD6–A6;

A8/IAD7–B6; A9/IAD8–C6; A10/IAD9–D6; A11/IAD10–A5; A12/IAD11–B5; A13/IAD12–C5

Data Bus D0/IAD13–P2; D1/IAD14–N2; D2/IAD15–M2; D3/IACK–L2; D4/IS–M3; D5/IAL–L3; D6/IRD–N4; D7/IWR–M4;

D8–L4; D9–L5; D10–N6; D11–M6; D12–L6; D13–N7; D14–M7; D15–L7; D16–K7; D17–K6; D18–K5; D19–K4; D20–J7; D21–J6; D22–J5; D23–J4

NOTES

Interrupt/Flag pins retain both functions concurrently. If IMASK is set to enable the corresponding interrupts, then the DSP will vector to the appropriate interrupt

vector address when the pin is asserted, either by external devices, or set as a programmable flag.

SPORT conﬁguration determined by the DSP System Control Register. Software conﬁgurable.

–8–

REV. 0

Page 9

AD73411

ARCHITECTURE OVERVIEW

The AD73411 instruction set provides flexible data moves and multifunction (one or two data moves with a computation) instructions. Every instruction can be executed in a single processor cycle. The AD73411 assembly language uses an algebraic syntax for ease of coding and readability. A comprehensive set of development tools supports program development.

DATA

ADDRESS

GENERATORS

DAG 2

DAG 1

ARITHMETIC UNITS

ADSP-2100 BASE

ARCHITECTURE

PROGRAM

SEQUENCER

PROGRAM MEMORY ADDRESS

DATA MEMORY ADDRESS

PROGRAM MEMORY DATA

DATA MEMORY DATA

SHIFTERMACALU

REF

POWER-DOWN

CONTROL

MEMORY

16K DM

16K PM

(OPTIONAL

SPORT 0

ANALOG FRONT END

8K)

SERIAL PORTS

SPORT 1

SERIAL PORT

SPORT 2

ADC DAC

SECTION

8K)

PROGRAMMABLE

I/O

AND

FLAGS

TIMER

FULL MEMORY

MODE

EXTERNAL

ADDRESS

BUS

EXTERNAL

DATA

BUS

BYTE DMA

CONTROLLER

EXTERNAL

DATA

BUS

INTERNAL

DMA

PORT

HOST MODE

Figure 1. Functional Block Diagram

Figure 1 is an overall block diagram of the AD73411. The processor section contains three independent computational units: the ALU, the multiplier/accumulator (MAC) and the shifter. The computational units directly process 16-bit data and have provisions to support multiprecision computations. The ALU performs a standard set of arithmetic and logic operations; division primitives are also supported. The MAC performs single-cycle multiply, multiply/add and multiply/subtract operations with 40 bits of accumulation. The shifter performs logical and arithmetic shifts, normalization, denormalization, and derive exponent operations.

The internal result (R) bus connects the computational units so that the output of any unit may be the input of any unit on the next cycle.

A powerful program sequencer and two dedicated data address generators ensure efﬁcient delivery of operands to these computational units. The sequencer supports conditional jumps, subroutine calls and returns in a single cycle. With internal loop counters and loop stacks, the AD73411 executes looped code with zero overhead; no explicit jump instructions are required to maintain loops.

Two data address generators (DAGs) provide addresses for simultaneous dual operand fetches (from data memory and program memory). Each DAG maintains and updates four address pointers. Whenever the pointer is used to access data (indirect addressing), it is post-modiﬁed by the value of one of four possible modify registers. A length value may be associated with each pointer to implement automatic modulo addressing for circular buffers.

The two address buses (PMA and DMA) share a single external address bus, allowing memory to be expanded off-chip, and the two data buses (PMD and DMD) share a single external data bus. Byte memory space and I/O memory space also share the external buses.

An interface to low-cost byte-wide memory is provided by the Byte DMA port (BDMA port). The BDMA port is bidirectional and can directly address up to four megabytes of external RAM or ROM for off-chip storage of program overlays or data tables.

The AD73411 can respond to eleven interrupts. There can be up to six external interrupts (one edge-sensitive, two level-sensitive, and three conﬁgurable), and seven internal interrupts generated by the timer, the serial ports (SPORTs), the Byte DMA port and the power-down circuitry. There is also a master RESET signal. The two serial ports provide a complete synchronous serial interface with optional companding in hardware and a wide variety of framed or frameless data transmit and receive modes of operation.

Each port can generate an internal programmable serial clock or accept an external serial clock.

The AD73411 provides up to 13 general-purpose flag pins. The data input and output pins on SPORT1 can be alternatively conﬁgured as an input flag and an output flag. In addition, eight flags are programmable as inputs or outputs and three flags are always outputs.

A programmable interval timer generates periodic interrupts. A 16-bit count register (TCOUNT) is decremented every n processor cycle, where n is a scaling value stored in an 8-bit register (TSCALE). When the value of the count register reaches zero, an interrupt is generated and the count register is reloaded from a 16-bit period register (TPERIOD).

Analog Front End

The AFE section is conﬁgured as a separate block that is normally connected to either SPORT0 or SPORT1 of the DSP section. As it is not hardwired to either SPORT, users have total flexibility in how they wish to allocate system resources to support the AFE. It is also possible to further expand the number of analog I/O channels connected to the SPORT by cascading other single or dual channel AFEs (AD73311 or AD73322) external to the AD73411.

REV. 0

–9–

Page 10

AD73411

DVDDAVDD2AVDD1

VINP

VINN

VOUTP

VOUTN

REFCAP

REFOUT

ANALOG

LOOPBACK/

SINGLE-ENDED

ENABLE

+6/–15dB

PGA

0/38dB

PGA

CONTINUOUS

TIME

LOW-PASS FILTER

REFERENCE

AGND1

AGND2

ANALOG

SIGMA-DELTA

MODULATOR

SWITCHEDCAPACITOR

LOW-PASS FILTER

Figure 2. Functional Block Diagram of Analog Front End Section

The AFE is conﬁgured as a single I/O channel (similar to that of the discrete AD73311L; refer to the AD73311L data sheet for more details) having a 16-bit sigma-delta-based ADC and DAC. Both ADC and DAC share a common reference whose nominal value is 1.2 V. Figure 2 shows a block diagram of the AFE section of the AD73411. It shows an ADC and DAC as well as a common reference. Communication to both channels is handled by the SPORT2 block which interfaces to either SPORT0 or SPORT1 of the DSP section.

The I/O channel features fully differential inputs and outputs. The input section allows direct connection to the internal Programmable Gain Ampliﬁer at the input of the sigma-delta ADC section. The input section also features programmable differential channel inversion and conﬁguration of the differential input as two separate single-ended inputs. The ADC features a second order sigma-delta modulator which samples at MCLK/8. Its bitstream output is ﬁltered and decimated by a Sinc-cubed decimator to provide a sample rate selectable from 64 kHz, 32 kHz, 16 kHz or 8 kHz (based on an MCLK of 16.384 MHz).

The DAC channel features a Sinc-cubed interpolator which increases the sample rate from the selected rate to the digital sigma-delta modulator rate of MCLK/8. The digital sigma-delta modulator’s output bitstream is fed to a single-bit DAC whose output is reconstructed/ﬁltered by two stages of low-pass ﬁltering (switched capacitor and continuous time) before being applied to the differential output driver.

FUNCTIONAL DESCRIPTION Encoder Channel

The encoder channel consists of an input conﬁguration block, a switched capacitor PGA and a sigma-delta analog-to-digital converter (ADC). An on-board digital ﬁlter, which forms part of the sigma-delta ADC, also performs critical system-level ﬁltering. Due to the high level of oversampling, the input antialias requirements are reduced such that a simple single pole RC stage is sufﬁcient to give adequate attenuation in the band of interest.

Input Conﬁguration Block

The input conﬁguration block consists of a multiplexing arrangement that allows selection of various input conﬁgurations. This includes ADC input selection from either the VINP, VINN pins

SDI

1-BIT

DAC

AD73411

DIGITAL

SIGMA-DELTA

MODULATOR

DECIMATOR

INTERPOLATOR

DGND

SERIAL

I/O

PORT

SDIFS

SCLK

SDO

SDOFS

MCLK

RESET

or from the DAC output via the Analog Loop-Back (ALB) arrangement. Differential inputs can be inverted and it is also possible to use the device in single-ended mode, which allows the option of using the VINP, VINN pins as two separate single-ended inputs, either of which can be selected under software control.

Programmable Gain Ampliﬁer

The encoder section’s analog front end comprises a switched capacitor PGA that also forms part of the sigma-delta modulator. The SC sampling frequency is DMCLK/8. The PGA, whose programmable gain settings are shown in Table I, may be used to increase the signal level applied to the ADC from low output sources such as microphones, and can be used to avoid placing external ampliﬁers in the circuit. The input signal level to the sigma-delta modulator should not exceed the maximum input voltage permitted.

The PGA gain is set by bits IGS0, IGS1 and IGS2 (CRD:0–2) in Control Register D.

Table I. PGA Settings for the Encoder Channel

IGS2 IGS1 IGS0 Gain (dB)

00 0 0 00 1 6 01 0 12 01 1 18 10 0 20 10 1 26 11 0 32 11 1 38

ADC

The ADC consists of an analog sigma-delta modulator and a digital antialiasing decimation ﬁlter. The sigma-delta modulator noise-shapes the signal and produces 1-bit samples at a DMCLK/8 rate. This bitstream, representing the analog input signal, is input to the antialiasing decimation ﬁlter. The decimation ﬁlter reduces the sample rate and increases the resolution.

–10–

REV. 0

Page 11

AD73411

Analog Sigma-Delta Modulator

The AD73411 input channel employs a sigma-delta conversion technique, which provides a high resolution 16-bit output with system ﬁltering being implemented on-chip.

Sigma-delta converters employ a technique known as oversampling, where the sampling rate is many times the highest frequency of interest. In the case of the AD73411, the initial sampling rate of the sigma-delta modulator is DMCLK/8. The main effect of oversampling is that the quantization noise is spread over a very wide bandwidth, up to f

/2 = DMCLK/16

(Figure 3a). This means that the noise in the band of interest is much reduced. Another complementary feature of sigma-delta converters is the use of a technique called noise-shaping. This technique has the effect of pushing the noise from the band of interest to an out-of-band position (Figure 3b). The combination of these techniques, followed by the application of a digital ﬁlter, sufﬁciently reduces the noise in band to ensure good dynamic performance from the part (Figure 3c).

BAND

INTEREST

fS/2

DMCLK/16

multiple of DMCLK/256, which is the decimation ﬁlter update rate. The ﬁnal detail in Figure 4d shows the application of a ﬁnal antialias ﬁlter in the DSP engine. This has the advantage of being implemented according to the user’s requirements and available MIPS. The ﬁltering in Figures 4a through 4c is implemented in the AD73411.

FB = 4kHz F

SINIT

= DMCLK/8

a. Analog Antialias Filter Transfer Function

SIGNAL TRANSFER FUNCTION

NOISE TRANSFER FUNCTION

FB = 4kHz

SINIT

= DMCLK/8

b. Analog Sigma-Delta Modulator Transfer Function

NOISE-SHAPING

BAND

INTEREST

DMCLK/16

DIGITAL FILTER

BAND

INTEREST

DMCLK/16

Figure 3. Sigma-Delta Noise Reduction

Figure 4 shows the various stages of ﬁltering that are employed in a typical AD73411 application. In Figure 4a we see the transfer function of the external analog antialias ﬁlter. Even though it is a single RC pole, its cutoff frequency is sufﬁciently far away from the initial sampling frequency (DMCLK/8) that it takes care of any signals that could be aliased by the sampling frequency. This also shows the major difference between the initial oversampling rate and the bandwidth of interest. In Figure 4b, the signal and noise-shaping responses of the sigma-delta modulator are shown. The signal response provides further rejection of any high frequency signals while the noise-shaping will push the inherent quantization noise to an out-of-band position. The detail of Figure 4c shows the response of the digital decimation ﬁlter (Sinc-cubed response) with nulls every

REV. 0

–11–

FB = 4kHz F

SINTER

= DMCLK/256

c. Digital Decimator Transfer Function

FB = 4kHz

SFINAL

= 8kHz

SINTER

= DMCLK/256

d. Final Filter LPF (HPF) Transfer Function

Figure 4. AD73411 ADC Frequency Responses

Decimation Filter

The digital ﬁlter used in the AD73411 carries out two important functions. Firstly, it removes the out-of-band quantization noise, which is shaped by the analog modulator and secondly, it decimates the high-frequency bitstream to a lower rate 15-bit word.

The antialiasing decimation ﬁlter is a sinc-cubed digital ﬁlter that reduces the sampling rate from DMCLK/8 at the modulator to an output rate at the SPORT of DMCLK/M (where M depends on the sample rate setting—M = 256 @ 64 kHz; M = 512 @ 32 kHz, M = 1024 @ 16 kHz, M = 2048 @ 8 kHz), and increases the resolution from a single bit to 15 bits. Its Z transform is given as: [(1–Z–N)/(1–Z–1)]3 where N is determined by the sampling rate (N = 32 @ 64 kHz, N = 64 @ 32 kHz, N = 128 @ 16 kHz, N = 256 @ 8 kHz). This ensures a minimal group delay of 25 µs at the 64 kHz sampling rate.

Page 12

AD73411

ADC Coding

The ADC coding scheme is in twos complement format (see Figure 5). The output words are formed by the decimation ﬁlter, which grows the word length from the single-bit output of the sigma-delta modulator to a 15-bit word, which is the 16-bit transfer being used as a flag bit to indicate either control or data in the frame.

INN

INP

ADC CODE DIFFERENTIAL

INN

INP

ADC CODE SINGLE-ENDED

ANALOG

INPUT

ANALOG

INPUT

+ (V

REF

– (V

+ (V

– (V

ⴛ 0.32875)

REF

ⴛ 0.32875)

REF

ⴛ 0.6575)

REF

10...00 00...00 01...11

ⴛ 0.6575)

REF

10...00 00...00 01...11

REF

Figure 5. ADC Transfer Function

Decoder Channel

The decoder channel consists of a digital interpolator, digital sigma-delta modulator, a single bit digital-to-analog converter (DAC), an analog smoothing ﬁlter and a programmable gain ampliﬁer with differential output.

DAC Coding

The DAC coding scheme is in twos complement format with 0x7FFF being full-scale positive and 0x8000 being full-scale negative.

Interpolation Filter

The anti-imaging interpolation ﬁlter is a sinc-cubed digital ﬁlter which upsamples the 16-bit input words from the SPORT input rate of DMCLK/M (where M depends on the sample rate setting (M = 256 @ 64 kHz; M = 512 @ 32 kHz, M = 1024 @ 16 kHz, M = 2048 @ 8 kHz), to a rate of DMCLK/8 while ﬁltering to attenuate images produced by the interpolation process. Its Z transform is given as: [(1–Z

–N

)/(1–Z–1)]3 where N is determined by the sampling rate (N = 32 @ 64 kHz, N = 64 @ 32 kHz, N = 128 @ 16 kHz, N = 256 @ 8 kHz). The DAC receives 16-bit samples from the host DSP processor at a rate of DMCLK/M. If the host processor fails to write a new value to the serial port, the existing (previous) data is read again. The data stream is ﬁltered by the anti-imaging interpolation ﬁlter, but there is an option to bypass the interpolator for the minimum group delay conﬁguration by setting the IBYP bit (CRE:5) of Control Register E. The interpolation ﬁlter has the same characteristics as the ADC’s antialiasing decimation ﬁlter.

The output of the interpolation ﬁlter is fed to the DAC’s digital sigma-delta modulator, which converts the 16-bit data to 1-bit samples at a rate of DMCLK/8. The modulator noise-shapes the signal so that errors inherent to the process are minimized in the passband of the converter. The bitstream output of the sigma-delta modulator is fed to the single bit DAC where it is converted to an analog voltage.

Analog Smoothing Filter and PGA

The output of the single-bit DAC is sampled at DMCLK/8, therefore it is necessary to ﬁlter the output to reconstruct the low frequency signal. The decoder’s analog smoothing ﬁlter consists of a continuous-time ﬁlter preceded by a third-order switched-capacitor ﬁlter. The continuous-time ﬁlter forms part of the output programmable gain ampliﬁer (PGA). The PGA can be used to adjust the output signal level from –15 dB to +6 dB in 3 dB steps, as shown in Table II. The PGA gain is set by bits OGS0, OGS1 and OGS2 (CRD:4-6) in Control Register D.

Table II. PGA Settings for the Decoder Channel

OGS2 OGS1 OGS0 Gain (dB)

00 06 00 13 01 00 01 1–3 10 0–6 10 1–9 1 1 0 –12 1 1 1 –15

Differential Output Ampliﬁers

The decoder has a differential analog output pair (VOUTP and VOUTN). The output channel can be muted by setting the MUTE bit (CRD:7) in Control Register D. The output signal is dc-biased to the codec’s on-chip voltage reference.

Voltage Reference

The AD73411 reference, REFCAP, is a bandgap reference that provides a low noise, temperature-compensated reference to the DAC and ADC. A buffered version of the reference is also made available on the REFOUT pin and can be used to bias other external analog circuitry. The reference has a default nominal value of 1.2 V.

The reference output (REFOUT) can be enabled for biasing external circuitry by setting the RU bit (CRC:6) of CRC.

AFE Serial Port (SPORT2)

The AFE section communicates with the DSP section via its bidirectional synchronous serial port (SPORT2), which interfaces to either SPORT0 or SPORT1 of the DSP section. SPORT2 is used to transmit and receive digital data and control information. This allows other single or dual codec devices to be cascaded together (up to a limit of eight codec units).

In both transmit and receive modes, data is transferred at the serial clock (SCLK2) rate with the MSB being transferred first. Communications between the AFE section and the DSP section must always be initiated by the AFE section (AFE is in master mode—DSP SPORT is in slave mode). This ensures that there is no collision between input data and output samples.

–12–

REV. 0

Page 13

AD73411

SPORT2 Overview

SPORT2 is a flexible, full-duplex, synchronous serial port whose protocol has been designed to allow extra AFE devices (AD733xx series), up to a maximum of eight I/O channels, to be connected in cascade to a DSP SPORT (0 or 1). It has a very flexible architecture that can be configured by programming two of the internal control registers. SPORT2 has three distinct modes of operation: Control Mode, Data Mode and Mixed Control/Data Mode.

In Control Mode (CRA:0 = 0), the device’s internal conﬁguration can be programmed by writing to the ﬁve internal control registers. In this mode, control information can be written to or read from the codec. In Data Mode (CRA:0 = 1), information that is sent to the device is used to update the decoder section (DAC), while the encoder section (ADC) data is read from the device. In this mode, only DAC and ADC data is written to or read from the device. Mixed mode (CRA:0 = 1 and CRA:1 = 1) allows the user to choose whether the information being sent to the device contains either control information or DAC data. This is achieved by using the MSB of the 16-bit frame as a flag bit. Mixed mode reduces the resolution to 15 bits, with the MSB being used to indicate whether the information in the 16-bit frame is control information or DAC/ADC data.

The SPORT features a single 16-bit serial register that is used for both input and output data transfers. As the input and output data must share the same register some precautions must be observed. The primary precaution is that no information be written to the SPORT without reference to an output sample event, which is when the serial register will be overwritten with the latest ADC sample word. Once the SPORT starts to output the latest ADC word, it is safe for the DSP to write new control or data words to the codec. In certain conﬁgurations, data can be written to the device to coincide with the output sample being shifted out of the serial register—see section on interfacing devices. The serial clock rate (CRB:2–3) deﬁnes how many 16-bit words can be written to a device before the next output sample event will happen.

The SPORT block diagram, shown in Figure 6, details the six control registers (A–F), external MCLK to internal DMCLK divider, and serial clock divider. The divider rates are controlled by the setting of Control Register B. The AD73411 features a master clock divider that allows users the flexibility of dividing externally available high-frequency DSP or CPU clocks to generate a lower frequency master clock internally in the codec which may be more suitable for either serial transfer or sampling rate requirements. The master clock divider has ﬁve divider options (÷ 1 default condition, ÷ 2, ÷ 3, ÷ 4, ÷ 5) that are set by loading the master clock divider ﬁeld in Register B with the appropriate code. Once the internal device master clock (DMCLK) has been set using the master clock divider, the sample rate and serial clock settings are derived from DMCLK.

The SPORT can work at four different serial clock (SCLK) rates: chosen from DMCLK, DMCLK/2, DMCLK/4, or DMCLK/8, where DMCLK is the internal or device master clock resulting from the external or pin master clock being divided by the

master clock divider. When working at the lower SCLK rate of DMCLK/8, which is intended for interfacing with slower DSPs, the SPORT will support a maximum of two devices in cascade with the sample rate of DMCLK/256.

SPORT2 Register Maps

There are two register banks for the AD73411: the control register bank and the data register bank. The control register bank consists of six read/write registers, each eight bits wide. Table VII shows the control register map for the AD73411. The ﬁrst two control registers, CRA and CRB, are reserved for controlling the SPORT. They hold settings for parameters such as bit rate, internal master clock rate, and device count (used when more than one AFE is connected in cascade from a single SPORT). The other three registers; CRC, CRD, and CRE are used to hold control settings for the ADC, DAC, Reference, and Power Control sections of the device. Control registers are written to on the negative edge of SCLK. The data register bank consists of two 16-bit registers that are the DAC and ADC registers.

Master Clock Divider

The AD73411 features a programmable master clock divider that allows the user to reduce an externally available master clock, at pin MCLK, by one of the ratios 1, 2, 3, 4, or 5, to produce an internal master clock signal (DMCLK) that is used to calculate the sampling and serial clock rates. The master clock divider is programmable by setting CRB:4–6. Table III shows the division ratio corresponding to the various bit settings. The default divider ratio is divide-by-one.

Table III. DMCLK (Internal) Rate Divider Settings

MCD2 MCD1 MCD0 DMCLK Rate

0 0 0 MCLK 0 0 1 MCLK/2 0 1 0 MCLK/3 0 1 1 MCLK/4 1 0 0 MCLK/5 1 0 1 MCLK 1 1 0 MCLK 1 1 1 MCLK

Serial Clock Rate Divider

The AD73411 features a programmable serial clock divider that allows users to match the serial clock (SCLK) rate of the data to that of the DSP engine or host processor. The maximum SCLK rate available is DMCLK and the other available rates are: DMCLK/2, DMCLK/4, and DMCLK/8. The slowest rate (DMCLK/8) is the default SCLK rate. The serial clock divider is programmable by setting bits CRB:2–3. Table IV shows the serial clock rate corresponding to the various bit settings.

Table IV. SCLK Rate Divider Settings

SCD1 SCD0 SCLK Rate

0 0 DMCLK/8 0 1 DMCLK/4 1 0 DMCLK/2 1 1 DMCLK

REV. 0

–13–

Page 14

AD73411

MCLK (EXTERNAL)

RESET

SDIFS

SDI

CONTROL

MCLK

DIVIDER

CONTROL

DMCLK (INTERNAL)

CONTROL

SERIAL PORT

(SPORT)

SERIAL REGISTER

Figure 6. SPORT Block Diagram

Sample Rate Divider

The AD73411 features a programmable sample rate divider that allows users flexibility in matching the codec’s ADC and DAC sample rates to the needs of the DSP software. The maximum sample rate available is DMCLK/256, which offers the lowest conversion group delay, while the other available rates are: DMCLK/512, DMCLK/1024, and DMCLK/2048. The slowest rate (DMCLK/2048) is the default sample rate. The sample rate divider is programmable by setting bits CRB:0–1. Table V shows the sample rate corresponding to the various bit settings.

Table V. Sample Rate Divider Settings

DIR1 DIR0 SCLK Rate

0 0 DMCLK/2048 0 1 DMCLK/1024 1 0 DMCLK/512 1 1 DMCLK/256

DAC Advance Register

The loading of the DAC is internally synchronized with the unloading of the ADC data in each sampling interval. The default DAC load event happens one SCLK cycle before the SDOFS flag is raised by the ADC data being ready. However, this DAC load position can be advanced before this time by modifying the contents of the DAC Advance ﬁeld in Control Register E (CRE:0–4). The ﬁeld is ﬁve bits wide, allowing 31 increments of weight 1/(DMCLK/8); see Table VI. In certain circumstances this can reduce the group delay when the ADC and DAC are used to process data in series.

Note: The DAC advance register should be changed before the DAC section is powered up.

Table VI. DAC Timing Control

SCLK

SDOFS

CONTROL

SDO

CONTROL

SCLK

DIVIDER

OPERATION Resetting the AFE Section of the AD73411

The RESET pin resets all the control registers. All registers are reset to zero, indicating that the default SCLK rate (DMCLK/8) and sample rate (DMCLK/2048) are at a minimum to ensure that slow speed DSP engines can communicate effectively. As well as resetting the control registers using the RESET pin, the device can be reset using the RESET bit (CRA:7) in Control Register A. Both hardware and software resets require four DMCLK cycles. On reset, DATA/PGM (CRA:0) is set to 0 (default condition) thus enabling Program Mode. The reset conditions ensure that the device must be programmed to the correct settings after power-up or reset. Following a reset, the SDOFS will be asserted 2048 DMCLK cycles after RESET going high. The data that is output following RESET and during Program Mode is random and contains no valid information until either Data or Mixed Mode is set.

Power Management

The individual functional blocks of the AFE can be enabled separately by programming the power control register CRC. It allows certain sections to be powered down if not required, which adds to the device’s flexibility in that the user need not incur the penalty of having to provide power for a certain section if it is not necessary to their design. The power control register provides individual control settings for the major functional blocks and also a global override that allows all sections to be powered up by setting the bit. Using this method the user could, for example, individually enable a certain section, such as the reference (CRC:5), and disable all others. The global power-up (CRC:0) can be used to enable all sections but if power-down is required using the global control, the reference will still be enabled, in this case, because its individual bit is set. Refer to Table XI for details of the settings of CRC.

DA4 DA3 DA2 DA1 DA0 Time Advance*

000000 ns

00001488.2 ns

00010976.5 ns ——————

1111014.64 µs

1111115.13 µs

*DMCLK = 16.384 MHz.

–14–

REV. 0

Page 15

AD73411

Table VII. Control Register Map

Address (Binary) Name Description Type Width Reset Setting (Hex)

000 CRA Control Register A R/W 8 0x00 001 CRB Control Register B R/W 8 0x00 010 CRC Control Register C R/W 8 0x00 011 CRD Control Register D R/W 8 0x00 100 CRE Control Register E R/W 8 0x00 101 CRF Control Register F R/W 8 0x00 110 to 111 Reserved

Table VIII. Control Word Description

514131211101 9876543210

/C D /R W sserddAeciveDsserddAretsigeRataDretsigeR

Control Frame Description

Bit 15 Control/Data When set high, it signiﬁes a control word in Program or Mixed Program/Data Modes. When

set low, it signiﬁes a data word in Mixed Program/Data Mode or an invalid control word in Program Mode.

Bit 14 Read/Write When set low, it tells the device that the data ﬁeld is to be written to the register selected by

the register ﬁeld setting provided the address ﬁeld is zero. When set high, it tells the device that the selected register is to be written to the data ﬁeld in the input serial register and that the new control word is to be output from the device via the serial output.

Bits 13–11 Device Address This 3-bit ﬁeld holds the address information. Only when this ﬁeld is zero is a device selected.

If the address is not zero, it is decremented and the control word is passed out of the device via the serial output.

Bits 10–8 Register Address This 3-bit ﬁeld is used to select one of the ﬁve control registers on the AD73411.

Bits 7–0 Register Data This 8-bit ﬁeld holds the data that is to be written to or read from the selected register provided

the address ﬁeld is zero.

CONTROL REGISTER A

REV. 0

Table IX. Control Register A Description

7654321 0

RESET DC2 DC1 DC0 SLB DLB MM DATA/PGM

Bit Name Description

0 DATA/PGM Operating Mode (0 = Program; 1 = Data Mode) 1 MM Mixed Mode (0 = Off; 1 = Enabled) 2 DLB Digital Loop-Back Mode (0 = Off; 1 = Enabled) 3 SLB SPORT Loop-Back Mode (0 = Off; 1 = Enabled) 4 DC0 Device Count (Bit 0) 5 DC1 Device Count (Bit 1) 6 DC2 Device Count (Bit 2) 7 RESET Software Reset (0 = Off; 1 = Initiates Reset)

–15–

Page 16

AD73411

CONTROL REGISTER B

CONTROL REGISTER C

Table X. Control Register B Description

76543210

CEE MCD2 MCD1 MCD0 SCD1 SCD0 DIR1 DIR0

Bit Name Description

0 DIR0 Decimation/Interpolation Rate (Bit 0) 1 DIR1 Decimation/Interpolation Rate (Bit 1) 2 SCD0 Serial Clock Divider (Bit 0) 3 SCD1 Serial Clock Divider (Bit 1) 4 MCD0 Master Clock Divider (Bit 0) 5 MCD1 Master Clock Divider (Bit 1) 6 MCD2 Master Clock Divider (Bit 2) 7 CEE Control Echo Enable (0 = Off; 1 = Enabled)

Table XI. Control Register C Description

76543210

RES RU PUREF PUDAC PUADC RES RES PU

CONTROL REGISTER D

Bit Name Description

0 PU Power-Up Device (0 = Power Down; 1 = Power-On) 1 Reserved Must Be Programmed to Zero (0) 2 Reserved Must Be Programmed to Zero (0) 3 PUADC ADC Power (0 = Power Down; 1 = Power On) 4 PUDAC DAC Power (0 = Power Down; 1 = Power On) 5 PUREF REF Power (0 = Power Down; 1 = Power On) 6 RU REFOUT Use (0 = Disable REFOUT; 1 = Enable

REFOUT)

7 Reserved Must Be Programmed to Zero (0)

Table XII. Control Register D Description

76543210

MUTE OGS2 OGS1 OGS0 RMOD IGS2 IGS1 IGS0

Bit Name Description

0 IGS0 Input Gain Select (Bit 0) 1 IGS1 Input Gain Select (Bit 1) 2 IGS2 Input Gain Select (Bit 2) 3 RMOD Reset ADC Modulator (0 = Off; 1 = Reset Enabled) 4 OGS0 Output Gain Select (Bit 0) 5 OGS1 Output Gain Select (Bit 1) 6 OGS2 Output Gain Select (Bit 2) 7 MUTE Output Mute (0 = Mute Off; 1 = Mute Enabled)

–16–

REV. 0

Page 17

CONTROL REGISTER E

CONTROL REGISTER F

AD73411

Table XIII. Control Register E Description

76543210

RES RES IBYP DA4 DA3 DA2 DA1 DA0

Bit Name Description

0 DA0 DAC Advance Setting (Bit 0) 1 DA1 DAC Advance Setting (Bit 1) 2 DA2 DAC Advance Setting (Bit 2) 3 DA3 DAC Advance Setting (Bit 3) 4 DA4 DAC Advance Setting (Bit 4) 5 IBYP Interpolator Bypass (0 = Bypass Disabled;

1 = Bypass Enabled) 6 Reserved Must Be Programmed to Zero (0) 7 Reserved Must Be Programmed to Zero (0)

Table XIV. Control Register F Description

76543210

ALB INV SEEN RES RES RES RES RES

Bit Name Description

0 Reserved Must Be Programmed to Zero (0) 1 Reserved Must Be Programmed to Zero (0) 2 Reserved Must Be Programmed to Zero (0) 3 Reserved Must Be Programmed to Zero (0) 4 Reserved Must Be Programmed to Zero (0) 5 SEEN Single-Ended Enable (0 = Disabled; 1 = Enabled) 6 INV Input Invert (0 = Disabled; 1 = Enabled) 7 ALB Analog Loopback of Output to Input (0 = Disabled; 1 = Enabled)

REV. 0

–17–

Page 18

AD73411

AFE Operating Modes

Five operating modes are available on the AFE. Two of these— Digital Loop-Back and Sport Loop-Back—are provided as diagnostic modes with the other three, Program, Data and Mixed Program/Data, being available for general-purpose use. The device conﬁguration—register settings—can be changed only in Program, and Mixed Program/Data Modes. In all modes, transfers of information to or from the device occur in 16-bit packets, therefore the DSP engine’s SPORT will be programmed for 16-bit transfers.

Program (Control) Mode

In Program Mode, CRA:0 = 0, the user writes to the control registers to set up the device for desired operation—SPORT operation, cascade length, power management, input/output gain, etc. In this mode, the 16-bit information packet sent to the device by the DSP engine is interpreted as a control word whose format is shown in Table VIII. In this mode, the user must address the device to be programmed using the address ﬁeld of the control word. This ﬁeld is read by the device and if it is zero (000 bin), the device recognizes the word as being addressed to it. If the address ﬁeld is not zero, it is then decremented and the control word is passed out of the device—either to the next device in a cascade or back to the DSP engine. This 3-bit address format allows the user to uniquely address any one of up to eight devices in a cascade; please note that this addressing scheme is valid only in sending control information to the device—a different format is used to send DAC data to the device(s). In a single codec conﬁguration, all control word addresses must be zero, otherwise they will not be recognized; in a multicodec conﬁguration all addresses from zero to N-1 (where N = number of devices in cascade) are valid.

Following reset, when the SE pin is enabled, the codec responds by raising the SDOFS pin to indicate that an output sample event has occurred. Control words can be written to the device to coincide with the data being sent out of the SPORT, as shown in Figure 7, or they can lag the output words by a time interval that should not exceed the sample interval. After reset, output frame sync pulses will occur at a slower default sample rate, which is DMCLK/2048, until Control Register B is programmed, after which the SDOFS pulses will occur at a rate set by the DIR0–1 bits of CRB. This is to allow slow controller devices to establish communication with the AFE. During Program Mode, the data output by the device is random and should not be interpreted as ADC data.

Data Mode

Once the device has been conﬁgured by programming the correct settings to the various control registers, the device may exit Program Mode and enter Data Mode. This is done by programming the DATA/PGM (CRA:0) bit to a 1 and MM (CRA:1) to

0. Once the device is in Data Mode, the 16-bit input data frame is now interpreted as DAC data rather than a control frame. This data is therefore loaded directly to the DAC register. In Data Mode, as the entire input data frame contains DAC data, the device relies on counting the number of input frame syncs

received at the SDIFS pin. When that number equals the device count stored in the device count ﬁeld of CRA, the device knows that the present data frame being received is its own DAC update data. When the device is in normal Data Mode (i.e., mixed mode disabled), it must receive a hardware reset to reprogram any of the control register settings. In a single codec conﬁguration, each 16-bit data frame sent from the DSP to the device is interpreted as DAC data. The default device count is 1, therefore each input frame sync will cause the 16-bit data frame to be loaded to the DAC register.

Mixed Program/Data Mode

This mode allows the user to send control words to the device along with the DAC data. This permits adaptive control of the device whereby control of the input/output gains can be affected by interleaving control words along with the normal flow of DAC data. The standard data frame remains 16 bits, but now the MSB is used as a flag bit to indicate whether the remaining 15 bits of the frame represent DAC data or control information. In the case of DAC data, the 15 bits are loaded with MSB justiﬁcation and LSB set to 0 to the DAC register. Mixed Mode is enabled by setting the MM bit (CRA:1) to 1 and the DATA/PGM bit (CRA:0) to 1. In the case where control setting changes will be required during normal operation, this mode allows the ability to load both control and data information with the slight inconvenience of formatting the data. Note that the output samples from the ADC will also have the MSB set to zero to indicate it is a data word.

Digital Loop-Back

This mode can be used for diagnostic purposes and allows the user to feed the ADC samples from the ADC register directly to the DAC register. This forms a loop-back of the analog input to the analog output by reconstructing the encoded signal using the decoder channel. The serial interface will continue to work, which allows the user to control gain settings, etc. Only when DLB is enabled with Mixed Mode operation can the user disable the DLB, otherwise the device must be reset.

Sport Loop-Back

This mode allows the user to verify the DSP interfacing and connection by writing words to the SPORT of the device and have them returned back unchanged at the next sample interval. The frame sync and data word that are sent to the device are returned via the output port. Again, SLB mode can only be disabled when used in conjunction with mixed mode, otherwise the device must be reset.

Analog Loop-Back

In Analog Loop-Back mode, the differential DAC output is connected, via a loop-back switch, to the ADC input (see Figure

9). This mode allows the ADC channel to check functionality of the DAC channel as the reconstructed output signal can be monitored using the ADC as a sampler. Analog Loop-Back is enabled by setting the ALB bit (CRF:7).

–18–

REV. 0

Page 19

SCLK

SDOFS

AD73411

SDO

SDIFS

SDI

SCLK

SDOFS(2)

SAMPLE WORD (DEVICE 1) SAMPLE WORD (DEVICE 1)

DATA (CONTROL) WORD (DEVICE 1) DATA (CONTROL) WORD (DEVICE 1)

Figure 7. Interface Signal Timing for Single Device Operation

REV. 0

SDO(2)

SDOFS(1)

SDIFS(2)

SDO(1)

SDI(2)

SDIFS(1)

SDI(1)

SAMPLE WORD (DEVICE 2) SAMPLE WORD (DEVICE 1)

SAMPLE WORD (DEVICE 1)

DATA (CONTROL) WORD (DEVICE 2) DATA (CONTROL) WORD (DEVICE 1)

DATA (CONTROL) WORD (DEVICE 2)

Figure 8. Interface Signal Timing for Cascade of Two Devices

–19–

Page 20

AD73411

ANALOG

VINP

VINN

VOUTP

VOUTN

REFOUT

REFCAP

LOOP-BACK

SELECT

+6/–15dB

PGA

REFERENCE

INVERT

CONTINUOUS

TIME

LOW-PASS

FILTER

SINGLE-ENDED

ENABLE

0/38dB

PGA

REF

AD73411

Figure 9. Analog Loop-Back Connectivity

AFE Interfacing

The AFE section SPORT (SPORT2) can be interfaced to either SPORT0 or SPORT1 of the DSP section. Both serial input and output data use an accompanying frame synchronization signal which is active high one clock cycle before the start of the 16-bit word or during the last bit of the previous word if transmission is continuous. The serial clock (SCLK) is an output from the codec and is used to define the serial transfer rate to the DSP’s Tx and Rx ports. Two primary configurations can be used: the first is shown in Figure 10 where the DSP’s Tx data, Tx Frame Sync, Rx data and Rx Frame Sync are connected to the codec’s SDI, SDIFS, SDO and SDOFS respectively. This configuration, referred to as indirectly coupled or nonframe sync loop-back, has the effect of decoupling the transmission of input data from the receipt of output data. The delay between receipt of codec output data and transmission of input data for the codec is determined by the DSP’s software latency. When programming the DSP serial port for this configuration, it is necessary to set the Rx Frame Sync as an input and the Tx Frame Sync as an output generated by the DSP. This configuration is most useful when operating in mixed mode, as the DSP has the ability to decide how many words (either DAC or control) can be sent to the codecs. This means that full control can be implemented over the device configuration as well as updating the DAC in a given sample interval. The second configuration (shown in Figure 11) has the DSP’s Tx data and Rx data connected to the codec’s SDI and SDO, respectively while the DSP’s Tx and Rx frame syncs are connected to the codec’s SDIFS and SDOFS. In this configuration, referred to as directly coupled or frame sync loop-back, the frame sync signals are connected together and the input data to the codec is forced to be synchronous with the output data from the codec. The DSP must be programmed so that both the Tx Frame Sync and Rx Frame Sync are inputs as the codec SDOFS will be input to both. This configuration guarantees that input and output events occur simultaneously and is the simplest configuration for operation in normal Data Mode. Note that when programming the DSP in this configuration it is advisable to preload the Tx register with the first control word to be sent before the codec is taken out of reset. This ensures that this word will be transmitted to coincide with the first output word from the device(s).

SDIFS

SDI

SCLK

SDO

SDOFS

AFE

SECTION

DSP

SECTION

TFS

SCLK

RFS

Figure 10. Indirectly Coupled or Nonframe Sync Loop-

Back Conﬁguration

Cascade Operation

The AD73411 has been designed to support up to eight codecs in a cascade connected to a single serial port. The SPORT interface protocol has been designed so that device addressing is built into the packet of information sent to the device. This allows the cascade to be formed with no extra hardware overhead for control signals or addressing. A cascade can be formed in either of the two modes previously discussed.

There may be some restrictions in cascade operation due to the number of devices conﬁgured in the cascade and the serial clock rate chosen. Table XV details the requirements for SCLK rate for cascade lengths from 1 to 8 devices. This assumes a directly coupled frame sync arrangement as shown in Figure 11.

Table XV. Cascade Options

Number of Devices in Cascade

SCLK 12345678

DMCLK ✓✓✓✓✓✓✓✓ DMCLK/2 ✓✓✓✓✓✓✓✓ DMCLK/4 ✓✓✓✓XXXX DMCLK/8 ✓✓XXXXXX

SDIFS

SDI

SCLK

SDO

SDOFS

AFE

SECTION

DSP

SECTION

TFS

SCLK

RFS

Figure 11. Directly Coupled or Frame Sync LoopBack Conﬁguration

When using the indirectly coupled frame sync conﬁguration in cascaded operation it is necessary to be aware of the restrictions in sending data to all devices in the cascade. Effectively, the time allowed is given by the sampling interval (256/DMCLK) which is 15.625 µs for a sample rate of 64 kHz. In this interval, the DSP must transfer N × 16 bits of information where N is the number of devices in the cascade. Each bit will take 1/SCLK and, allowing for any latency between the receipt of the Rx interrupt and the transmission of the Tx data, the relationship for successful operation is given by:

256/DMCLK > ((N × 16/SCLK) + T

INTERRUPT LATENCY

)

The interrupt latency will include the time between the ADC sampling event and the Rx interrupt being generated in the DSP—this should be 16 SCLK cycles.

–20–

REV. 0

Page 21

AD73411

In Cascade Mode, each device must know the number of devices in the cascade because the Data and Mixed modes use a method of counting input frame sync pulses to decide when they should update the DAC register from the serial input register. Control Register A contains a 3-bit ﬁeld (DC0–2) that is programmed by the DSP during the programming phase. The default condition is that the ﬁeld contains 000b, which is equivalent to a single device in cascade (see Table XVI). For cascade operation, however this ﬁeld must contain a binary value that is one less than the number of devices in the cascade.

Table XVI. Device Count Settings

DC2 DC1 DC0 Cascade Length

000 1 001 2 010 3 011 4 100 5 101 6 110 7 111 8

FUNCTIONAL DESCRIPTION—DSP

DATA

ADDRESS

GENERATORS

DAG 2

DAG 1

ARITHMETIC UNITS

ADSP-2100 BASE

ARCHITECTURE

PROGRAM

SEQUENCER

PROGRAM MEMORY ADDRESS

DATA MEMORY ADDRESS

PROGRAM MEMORY DATA

DATA MEMORY DATA

SHIFTERMACALU

REF

POWER-DOWN

CONTROL

MEMORY

16K DM

16K PM

(OPTIONAL

SPORT 0

ANALOG FRONT END

8K)

SERIAL PORTS

SPORT 1

SERIAL PORT

SPORT 2

ADC1 DAC1

SECTION

8K)

PROGRAMMABLE

I/O

AND

FLAGS

TIMER

FULL MEMORY

MODE

EXTERNAL

ADDRESS

BUS

EXTERNAL

DATA

BUS

BYTE DMA

CONTROLLER

EXTERNAL

DATA

BUS

INTERNAL

DMA

PORT

HOST MODE

Figure 12. Functional Block Diagram

Figure 12 is an overall block diagram of the AD73411. The processor contains three independent computational units: the ALU, the multiplier/accumulator (MAC) and the shifter. The computational units process 16-bit data directly and have provisions to support multiprecision computations. The ALU performs a standard set of arithmetic and logic operations; division primitives are also supported. The MAC performs single-cycle multiply, multiply/add and multiply/subtract operations with 40 bits of

accumulation. The shifter performs logical and arithmetic shifts, normalization, denormalization and derive exponent operations.

The shifter can be used to efﬁciently implement numeric format control including multiword and block floating-point representations.

The internal result (R) bus connects the computational units so that the output of any unit may be the input of any unit on the next cycle.

Efﬁcient data transfer is achieved with the use of ﬁve internal buses:

• Program Memory Address (PMA) Bus

• Program Memory Data (PMD) Bus

• Data Memory Address (DMA) Bus

• Data Memory Data (DMD) Bus

• Result (R) Bus

Program memory can store both instructions and data, permitting the AD73411 to fetch two operands in a single cycle, one from program memory and one from data memory. The AD73411 can fetch an operand from program memory and the next instruction in the same cycle.

In lieu of the address and data bus for external memory connection, the AD73411 may be conﬁgured for 16-bit Internal DMA port (IDMA port) connection to external systems. The IDMA port is made up of 16 data/address pins and ﬁve control pins. The IDMA port provides transparent, direct access to the DSPs on-chip program and data RAM.

The byte memory and I/O memory space interface supports slow memories and I/O memory-mapped peripherals with programmable wait state generation. External devices can gain control of external buses with bus request/grant signals (BR, BGH, and BG). One execution mode (Go Mode) allows the AD73411 to continue running from on-chip memory. Normal execution mode requires the processor to halt while buses are granted.

REV. 0

–21–

Page 22

AD73411

The AD73411 can respond to eleven interrupts. There can be up to six external interrupts (one edge-sensitive, two levelsensitive and three conﬁgurable) and seven internal interrupts generated by the timer, the serial ports (SPORTs), the Byte DMA port and the power-down circuitry. There is also a master RESET signal. The two serial ports provide a complete synchronous serial interface with optional companding in hardware and a wide variety of framed or frameless data transmit and receive modes of operation.

Each port can generate an internal programmable serial clock or accept an external serial clock.

Serial Ports

The DSP section incorporates two complete synchronous serial ports (SPORT0 and SPORT1) for serial communications and multiprocessor communication.

Following is a brief list of the capabilities of the SPORTs. For additional information on Serial Ports, refer to the ADSP-2100 Family User’s Manual, Third Edition.

• SPORTs are bidirectional and have a separate, doublebuffered transmit and receive section.

• SPORTs can use an external serial clock or generate their own serial clock internally.

• SPORTs have independent framing for the receive and transmit sections. Sections run in a frameless mode or with frame synchronization signals internally or externally generated. Frame sync signals are active high or inverted, with either of two pulsewidths and timings.

• SPORTs support serial data word lengths from 3 to 16 bits and provide optional A-law and µ-law companding according to CCITT recommendation G.711.

• SPORT receive and transmit sections can generate unique interrupts on completing a data word transfer.

• SPORTs can receive and transmit an entire circular buffer of data with only one overhead cycle per data word. An interrupt is generated after a data buffer transfer.

• SPORT0 has a multichannel interface to selectively receive and transmit a 24- or 32-word, time-division multiplexed, serial bitstream.

• SPORT1 can be conﬁgured to have two external interrupts (IRQ0 and IRQ1) and the Flag In and Flag Out signals. The internally generated serial clock may still be used in this conﬁguration.

DSP SECTION PIN DESCRIPTIONS

The AD73411 is available in a 119-ball PBGA package. In order to maintain maximum functionality and reduce package size and pin count, some serial port, programmable flag, interrupt, and external bus pins have dual, multiplexed functionality. The external bus pins are conﬁgured during RESET only, while serial port pins are software conﬁgurable during program execution. Flag and interrupt functionality is retained concurrently on multiplexed pins. In cases where pin functionality is reconﬁgurable, the default state is shown in plain text; alternate functionality is shown in italics. See Pin Function Descriptions section.

Memory Interface Pins

The AD73411 processor can be used in one of two modes, Full Memory Mode, which allows BDMA operation with full external overlay memory and I/O capability, or Host Mode, which allows IDMA operation with limited external addressing capabilities. The operating mode is determined by the state of the Mode C pin during RESET and cannot be changed while the processor is running. See Full Memory Mode Pins and Host Mode Pins charts for descriptions.

Full Memory Mode Pins (Mode C = 0)

Pin # of Input/ Name(s) Pins Output Function

A13:0 14 O Address Output Pins for Program,

Data, Byte, and I/O Spaces

D23:0 24 I/O Data I/O Pins for Program, Data,

Byte, and I/O Spaces (8 MSBs are also used as Byte Memory addresses)

Host Mode Pins (Mode C = 1)

Pin # of Input/ Name(s) Pins Output Function

IAD15:0 16 I/O IDMA Port Address/Data Bus A0 1 O Address Pin for External I/O,

Program, Data, or Byte Access

D23:8 16 I/O Data I/O Pins for Program, Data

Byte and I/O Spaces

IWR 1 I IDMA Write Enable IRD 1 I IDMA Read Enable

IAL 1 I IDMA Address Latch Pin

IS 1 I IDMA Select IACK 1 O IDMA Port Acknowledge

NOTE In Host Mode, external peripheral addresses can be decoded using the A0, CMS, PMS, DMS, and IOMS signals.

–22–

REV. 0

Page 23

AD73411

Terminating Unused Pin

The following chart shows the recommendations for terminating unused pins.

Pin Terminations

I/O Hi-Z*

Pin 3-State Reset Caused Unused Name (Z) State By Conﬁguration

XTAL I I Float CLKOUT O O Float A13:1 or O (Z) Hi-Z BR, EBR Float IAD12:0 I/O (Z) Hi-Z IS Float A0 O (Z) Hi-Z BR, EBR Float D23:8 I/O (Z) Hi-Z BR, EBR Float D7 or I/O (Z) Hi-Z BR, EBR Float IWR I I High (Inactive) D6 or I/O (Z) Hi-Z BR, EBR Float IRD IIBR , EBR High (Inactive) D5 or I/O (Z) Hi-Z Float IAL I I Low (Inactive) D4 or I/O (Z) Hi-Z BR, EBR Float IS I I High (Inactive) D3 or I/O (Z) Hi-Z BR, EBR Float IACK Float D2:0 or I/O (Z) Hi-Z BR, EBR Float IAD15:13 I/O (Z) Hi-Z IS Float

PMS O (Z) O BR, EBR Float DMS O (Z) O BR, EBR Float BMS O (Z) O BR, EBR Float

IOMS O (Z) O BR, EBR Float

CMS O (Z) O BR, EBR Float RD O (Z) O BR, EBR Float WR O (Z) O BR, EBR Float BR I I High (Inactive) BG O (Z) O EE Float BGH O O Float IRQ2/PF7 I/O (Z) I Input = High (Inactive)

or Program as Output, Set to 1, Let Float

IRQL1/PF6 I/O (Z) I Input = High (Inactive)

or Program as Output, Set to 1, Let Float

IRQL0/PF5 I/O (Z) I Input = High (Inactive)

or Program as Output, Set to 1, Let Float

IRQE/PF4 I/O (Z) I Input = High (Inactive)

or Program as Output, Set to 1, Let Float

SCLK0 I/O I Input = High or Low,

Output = Float RFS0 I/O I High or Low DR0 I I High or Low TFS0 I/O O High or Low DT0 O O Float SCLK1 I/O I Input = High or Low,

Output = Float RFS1/IRQ0 I/O I High or Low DR1/FI I I High or Low TFS1/IRQ1 I/O O High or Low DT1/FO O O Float EE I I

EBR II EBG OO ERESET II EMS OO EINT II

ECLK I I ELIN I I ELOUT O O

NOTES *Hi-Z = High Impedance.

1. If the CLKOUT pin is not used, turn it OFF.

2. If the Interrupt/Programmable Flag pins are not used, there are two options: Option 1: When these pins are conﬁgured as INPUTS at reset and function as interrupts and input flag pins, pull the pins High (inactive). Option 2: Program the unused pins as OUTPUTS, set them to 1, and let them float.

3. All bidirectional pins have three-stated outputs. When the pins is conﬁgured as an output, the output is Hi-Z (high impedance) when inactive.

4. CLKIN, RESET, and PF3:0 are not included in the table because these pins must be used.

Interrupts

The interrupt controller allows the processor to respond to the eleven possible interrupts and RESET with minimum overhead. The AD73411 provides four dedicated external interrupt input pins, IRQ2, IRQL0, IRQL1, and IRQE. In addition, SPORT1 may be reconﬁgured for IRQ0, IRQ1, FLAG_IN, and FLAG_OUT, for a total of six external interrupts. The AD73411 also supports internal interrupts from the timer, the byte DMA port, the two serial ports, software, and the powerdown control circuit. The interrupt levels are internally prioritized and individually maskable (except power-down and reset). The IRQ2, IRQ0, and IRQ1 input pins can be programmed to be either level- or edge-sensitive. IRQL0 and IRQL1 are levelsensitive and IRQE is edge-sensitive. The priorities and vector addresses of all interrupts are shown in Table XVII.

Table XVII. Interrupt Priority and Interrupt Vector Addresses

Interrupt Vector

Source of Interrupt Address (Hex)

RESET (or Power-Up with PUCR = 1) 0000 (Highest Priority) Power-Down (Nonmaskable) 002C

IRQ2 0004 IRQL1 0008 IRQL0 000C

SPORT0 Transmit 0010 SPORT0 Receive 0014 IRQE 0018 BDMA Interrupt 001C SPORT1 Transmit or IRQ1 0020 SPORT1 Receive or IRQ0 0024 Timer 0028 (Lowest Priority)

Interrupt routines can either be nested, with higher priority interrupts taking precedence, or processed sequentially. Interrupts can be masked or unmasked with the IMASK register. Individual interrupt requests are logically ANDed with the bits in IMASK; the highest priority unmasked interrupt is then selected. The power-down interrupt is nonmaskable.

The AD73411 masks all interrupts for one instruction cycle following the execution of an instruction that modiﬁes the IMASK register. This does not affect serial port autobuffering or DMA transfers.

The interrupt control register, ICNTL, controls interrupt nesting and deﬁnes the IRQ0, IRQ1, and IRQ2 external interrupts to be either edge- or level-sensitive. The IRQE pin is an external edge-sensitive interrupt and can be forced and cleared. The IRQL0 and IRQL1 pins are external level-sensitive interrupts.

The IFC register is a write-only register used to force and clear interrupts. On-chip stacks preserve the processor status and are automatically maintained during interrupt handling. The stacks

REV. 0

–23–

Page 24

AD73411

are twelve levels deep to allow interrupt, loop, and subroutine nesting. The following instructions allow global enable or disable servicing of the interrupts (including power-down), regardless of the state of IMASK. Disabling the interrupts does not affect serial port autobuffering or DMA.

ENA INTS; DIS INTS;

When the processor is reset, interrupt servicing is enabled.

LOW-POWER OPERATION

The AD73411 has three low-power modes that signiﬁcantly reduce the power dissipation when the device operates under standby conditions. These modes are:

• Power-Down

• Idle

• Slow Idle

The CLKOUT pin may also be disabled to reduce external power dissipation.

Power-Down

The AD73411 processor has a low-power feature that lets the processor enter a very low-power dormant state through hardware or software control. Here is a brief list of power-down features. Refer to the ADSP-2100 Family User’s Manual, Third Edition, “System Interface” chapter, for detailed information about the power-down feature.

• Quick recovery from power-down. The processor begins executing instructions in as few as 400 CLKIN cycles.

• Support for an externally generated TTL or CMOS processor clock. The external clock can continue running during power-down without affecting the 400 CLKIN cycle recovery.

• Support for crystal operation includes disabling the oscillator to save power (the processor automatically waits 4096 CLKIN cycles for the crystal oscillator to start and stabilize), and letting the oscillator run to allow 400 CLKIN cycle startup.

• Power-down is initiated by either the power-down pin (PWD) or the software power-down force bit. Interrupt support allows an unlimited number of instructions to be executed before optionally powering down. The power-down interrupt also can be used as a nonmaskable, edge-sensitive interrupt.

• Context clear/save control allows the processor to continue where it left off or start with a clean context when leaving the power-down state.

• The RESET pin also can be used to terminate power-down.

• Power-down acknowledge pin indicates when the processor has entered power-down.

Idle

When the AD73411 is in the Idle Mode, the processor waits indeﬁnitely in a low power state until an interrupt occurs. When an unmasked interrupt occurs, it is serviced; execution then continues with the instruction following the IDLE instruction. In Idle Mode IDMA, BDMA, and Autobuffer Cycle steals still occur.

Slow Idle

The IDLE instruction on the AD73411 slows the processor’s internal clock signal, further reducing power consumption. The reduced clock frequency, a programmable fraction of the normal

clock rate, is speciﬁed by a selectable divisor given in the IDLE instruction. The format of the instruction is

IDLE (n);

where n = 16, 32, 64, or 128. This instruction keeps the processor fully functional, but operating at the slower clock rate. While it is in this state, the processor’s other internal clock signals, such as SCLK, CLKOUT, and Timer Clock, are reduced by the same ratio. The default form of the instruction, when no clock divisor is given, is the standard IDLE instruction.

When the IDLE (n) instruction is used, it effectively slows down the processor’s internal clock and thus its response time to incoming interrupts. The one-cycle response time of the standard idle state is increased by n, the clock divisor. When an enabled interrupt is received, the AD73411 will remain in the idle state for up to a maximum of n processor cycles (n = 16, 32, 64, or 128) before resuming normal operation.

When the IDLE (n) instruction is used in systems that have an externally generated serial clock (SCLK), the serial clock rate may be faster than the processor’s reduced internal clock rate. Under these conditions, interrupts must not be generated at a rate faster than can be serviced, due to the additional time the processor takes to come out of the idle state (a maximum of n processor cycles).

SYSTEM INTERFACE

Figure 13 shows a typical basic system conﬁguration with the AD73411, two serial devices, a byte-wide EPROM, and optional external program and data overlay memories (mode selectable). Programmable wait state generation allows the processor to connect easily to slow peripheral devices. The AD73411 also provides four external interrupts and two serial ports or six external interrupts and one serial port. Host Memory Mode allows access to the full external data bus, but limits addressing to a single address bit (A0). Additional system peripherals can be added in this mode through the use of external hardware to generate and latch address signals.

Clock Signals

The AD73411 can be clocked by either a crystal or a TTLcompatible clock signal.

The CLKIN input cannot be halted, changed during operation, or operated below the speciﬁed frequency during normal operation. The only exception is while the processor is in the power-down state. For detailed information on this power-down feature, refer to Chapter 9, ADSP-2100 Family User’s Manual, Third Edition.

If an external clock is used, it should be a TTL-compatible signal running at half the instruction rate. The signal is connected to the processor’s CLKIN input. When an external clock is used, the XTAL input must be left unconnected.

The AD73411 uses an input clock with a frequency equal to half the instruction rate; a 26.00 MHz input clock yields a 19 ns processor cycle (which is equivalent to 52 MHz). Normally, instructions are executed in a single processor cycle. All device timing is relative to the internal instruction clock rate, which is indicated by the CLKOUT signal when enabled.

–24–

REV. 0

Page 25

AD73411

FULL MEMORY MODE

1/2x CLOCK

CRYSTAL

AFE*

SECTION

OR SERIAL DEVICE

AFE*

SECTION

OR SERIAL DEVICE

1/2x CLOCK

CRYSTAL

AFE*

SECTION

SERIAL DEVICE

AFE*

SECTION

SERIAL DEVICE

SYSTEM

INTERFACE

␮CONTROLLER

AD73411

CLKIN XTAL

FL0–2 PF3

IRQ2/PF7 IRQE/PF4 IRQL0/PF5 IRQL1/PF6

MODE C/PF2 MODE B/PF1 MODE A/PF0

SPORT1

SCLK1 RFS1 OR IRQ0 TFS1 OR IRQ1 DT1 OR FO DR1 OR FI

SPORT0

SCLK0 RFS0 TFS0 DT0 DR0

HOST MEMORY MODE

AD73411

CLKIN

XTAL

FL0–2 PF3

IRQ2/PF7 IRQE/PF4 IRQL0/PF5 IRQL1/PF6

MODE C/PF2 MODE B/PF1 MODE A/PF0

SPORT1

SCLK1 RFS1 OR IRQ0 TFS1 OR IRQ1 DT1 OR FO DR1 OR FI

SPORT0

SCLK0 RFS0 TFS0 DT0 DR0

IDMA PORT

IRD/D6 IWR/D7 IS/D4

IAL/D5 IACK/D3

IAD15-0

ADDR13–0

DATA23–0

PWDACK

DATA23–8

PWDACK

BMS

IOMS

PMS DMS CMS

BR BG

BGH

PWD

BMS

IOMS

PMS DMS CMS

BR BG

BGH

PWD

23–16

*AFE SECTION CAN BE CONNECTED TO EITHER SPORT0 OR SPORT1

13–0

15–8

10–0

23–8

13–0

23–0

A0–A21

MEMORY

DATA

ADDR

I/O SPACE

(PERIPHERALS)

DATA

LOCATIONS

OVERLAY

ADDR

MEMORY

DATA

TWO 8K

PM SEGMENTS

TWO 8K

DM SEGMENTS

BYTE

2048

Figure 13. Basic System Conﬁguration

CLKIN CLKOUTXTAL

DSP

Figure 14. External Crystal Connections

Because the AD73411 includes an on-chip oscillator circuit, an external crystal may be used. The crystal should be connected across the CLKIN and XTAL pins, with two capacitors connected as shown in Figure 14. Capacitor values are dependent on crystal type and should be speciﬁed by the crystal manufacturer. A parallel-resonant, fundamental frequency, microprocessor-grade crystal should be used.

A clock output (CLKOUT) signal is generated by the processor at the processor’s cycle rate. This can be enabled and disabled by the CLK0DIS bit in the SPORT0 Autobuffer Control Register.

Reset

The RESET signal initiates a master reset of the DSP section of the AD73411. The RESET signal must be asserted during the power-up sequence to assure proper initialization. RESET during initial power-up must be held long enough to allow the internal clock to stabilize. If RESET is activated any time after power-up, the clock continues to run and does not require stabilization time.

The power-up sequence is deﬁned as the total time required for the crystal oscillator circuit to stabilize after a valid V

is applied

to the processor, and for the internal phase-locked loop (PLL) to lock onto the speciﬁc crystal frequency. A minimum of 2000 CLKIN cycles ensures that the PLL has locked, but does not include the crystal oscillator start-up time. During this power-up sequence the RESET signal should be held low. On any subsequent resets, the RESET signal must meet the minimum pulsewidth speciﬁcation, t

RSP

The RESET input contains some hysteresis; however, if an RC circuit is used to generate the RESET signal, an external Schmitt trigger is recommended.

The master reset sets all internal stack pointers to the empty stack condition, masks all interrupts, and clears the MSTAT register. When RESET is released, if there is no pending bus request and the chip is conﬁgured for booting, the boot-loading sequence is performed. Once boot loading completes, the ﬁrst instruction is fetched from on-chip program memory location 0x0000.

MODES OF OPERATION

Table XVII summarizes the AD73411 memory modes.

Setting Memory Mode

Memory Mode selection for the AD73411 is made during chip reset through the use of the Mode C pin. This pin is multiplexed with the DSP’s PF2 pin, so care must be taken in how the mode selection is made. The two methods for selecting the value of Mode C are active and passive.

Passive Conﬁguration involves the use a pull-up or pull-down resistor connected to the Mode C pin. To minimize power consumption, or if the PF2 pin is to be used as an output in the DSP application, a weak pull-up or pull-down, on the order of 100 kΩ, can be used. This value should be sufﬁcient to pull the pin to the desired level and still allow the pin to operate as a programmable flag output without undue strain on the processor’s output driver. For minimum power consumption during power-down, reconﬁgure PF2 to be an input, as the pull-up or pull-down will hold the pin in a known state and will not switch.

Active Conﬁguration involves the use of a three-statable external driver connected to the Mode C pin. A driver’s output enable should be connected to the DSP’s RESET signal such that it only drives the PF2 pin when RESET is active (low). When RESET is deasserted, the driver should three-state, thus allowing full use of the PF2 pin as either an input or output. To minimize power consumption during power-down, conﬁgure the programmable flag as an output when connected to a three-stated buffer. This ensures that the pin will be held at a constant level and not oscillate should the three-state driver’s level hover around the logic switching point.

REV. 0

–25–

Page 26

AD73411

Table XVIII. Modes of Operations

MODE C2MODE B3MODE A4Booting Method

0 0 0 BDMA feature is used to load the ﬁrst 32 program memory words from the byte memory

space. Program execution is held off until all 32 words have been loaded. Chip is conﬁgured in Full Memory Mode.

0 1 0 No automatic boot operations occur. Program execution starts at external memory location

0. Chip is conﬁgured in Full Memory Mode. BDMA can still be used, but the processor does not automatically use or wait for these operations.

1 0 0 BDMA feature is used to load the ﬁrst 32 program memory words from the byte memory

space. Program execution is held off until all 32 words have been loaded. Chip is conﬁgured in Host Mode.

1 0 1 IDMA feature is used to load any internal memory as desired. Program execution is held off

until internal program memory location 0 is written to. Chip is conﬁgured in Host Mode.

NOTES

All mode pins are recognized while RESET is active (low).

When Mode C = 0, Full Memory enabled. When Mode C = 1, Host Memory Mode enabled.

When Mode B = 0, Autobooting enabled. When Mode B = 1, no Autobooting.

When Mode A = 0, BDMA enabled. When Mode A = 1, IDMA enabled.

Considered as standard operating settings. Using these conﬁgurations allows for easier design and better memory management.

Requires additional hardware.

MEMORY ARCHITECTURE

The AD73411 provides a variety of memory and peripheral interface options. The key functional groups are Program Memory, Data Memory, Byte Memory, and I/O. Refer to the following ﬁgures and tables for PM and DM memory allocations in the AD73411.

PROGRAM MEMORY

Program Memory (Full Memory Mode) is a 24-bit-wide

space for storing both instruction op codes and data. The AD73411-80 has 16K words of Program Memory RAM on chip (the AD73411-40 has 8K words of Program Memory RAM on chip), and the capability of accessing up to two 8K external memory overlay spaces using the external data bus.

Program Memory (Host Mode) allows access to all internal memory. External overlay access is limited by a single external address line (A0). External program execution is not available in host mode due to a restricted data bus that is only 16 bits wide.

Table XIX. PMOVLAY Bits

0x2000– 0x3FFF

RESERVED

ADDRESS

0x3FFF

0x2000 0x1FFF

0x0000– 0x1FFF

INTERNAL MEMORY

EXTERNAL MEMORY

PM (MODE B = 0)

ALWAYS ACCESSIBLE AT ADDRESS

0x0000 – 0x1FFF

ACCESSIBLE

WHEN

PMOVLAY = 0

ACCESSIBLE WHEN PMOVLAY = 1

ACCESSIBLE WHEN PMOVLAY = 2

PROGRAM MEMORY

MODE B = 0

8K INTERNAL PMOVLAY = 0

8K EXTERNAL

PMOVLAY = 1 OR 2

8K INTERNAL

0x2000– 0x3FFF

ADDRESS

0x3FFF

0x2000 0x1FFF

PM (MODE B = 1)

RESERVED

INTERNAL MEMORY

0x2000–

0x3FFF

WHEN MODE B = 1, PMOVLAY MUST BE

SET TO 0

SEE TABLE XIX FOR PMOVLAY BITS

ACCESSIBLE

WHEN

PMOVLAY = 0

ACCESSIBLE WHEN PMOVLAY = 0

EXTERNAL MEMORY

PROGRAM MEMORY

MODE B = 1

8K INTERNAL PMOVLAY = 0

8K EXTERNAL

PMOVLAY Memory A13 A12:0

0 Internal Not Applicable Not Applicable 1 External 0 13 LSBs of Address

Overlay 1 Between 0x2000

and 0x3FFF

2 External 1 13 LSBs of Address

Overlay 2 Between 0x2000

and 0x3FFF

0x0000

Figure 15. Program Memory Map

DATA MEMORY

Data Memory (Full Memory Mode) is a 16-bit-wide space

used for the storage of data variables and for memory-mapped control registers. The AD73411-80 has 16K words on Data Memory RAM on-chip (the AD73411-40 has 8K words on Data Memory RAM on-chip), consisting of 16,352 user-accessible locations in the case of the AD73411-80 (8,160 user-accessible locations in the case of the AD73411-40) and 32 memorymapped registers. Support also exists for up to two 8K external memory overlay spaces through the external data bus. All internal accesses complete in one cycle. Accesses to external memory are timed using the wait states speciﬁed by the DWAIT register.

–26–

REV. 0

Page 27

AD73411

BDMA CONTROL

BMPAGE

BTYPE

BCR

0 = RUN DURING BDMA 1 = HALT DURING BDMA

00000000000 01000

1514131211109876543210

DM (0x3FE3)

BDIR

0 = LOAD FROM BM 1 = STORE TO BM

INTERNAL MEMORY

DATA MEMORY

ALWAYS ACCESSIBLE AT ADDRESS

0x2000 – 0x3FFF

ACCESSIBLE WHEN

DMOVLAY = 0

ACCESSIBLE WHEN

DMOVLAY = 1

EXTERNAL MEMORY

0x0000– 0

1FFF

ACCESSIBLE WHEN DMOVLAY = 2

0 0

0000–

1FFF

0 0

x x

0000– 1FFF

DATA MEMORY

32 MEMORY

MAPPED

REGISTERS

INTERNAL

8160

WORDS

8K INTERNAL DMOVLAY = 0

EXTERNAL 8K

DMOVLAY = 1, 2

ADDRESS

0x3FFF

0x3FE0 0

3FDF

0x2000

1FFF

0x0000

Figure 16. Data Memory Map

Data Memory (Host Mode) allows access to all internal memory. External overlay access is limited by a single external address line (A0). The DMOVLAY bits are deﬁned in Table XX.

Table XX. DMOVLAY Bits

DMOVLAY Memory A13 A12:0

0 Internal Not Applicable Not Applicable 1 External 0 13 LSBs of Address

Overlay 1 Between 0x2000

and 0x3FFF

2 External 1 13 LSBs of Address

Overlay 2 Between 0x2000

and 0x3FFF

I/O Space (Full Memory Mode)

The AD73411 supports an additional external memory space called I/O space. This space is designed to support simple connections to peripherals (such as data converters and external registers) or to bus interface ASIC data registers. I/O space supports 2048 locations of 16-bit-wide data. The lower 11-bits of the external address bus are used; the upper three bits are undeﬁned. Two instructions were added to the core ADSP-2100 Family Instruction Set to read from and write to I/O memory space. The I/O space also has four dedicated 3-bit wait state registers, IOWAIT03, that specify up to seven wait states to be automatically generated for each of four regions. The wait states act on address ranges as shown in Table XXI.

Table XXI. Wait States

Address Range Wait State Register

0x000–0x1FF IOWAIT0 0x200–0x3FF IOWAIT1 0x400–0x5FF IOWAIT2 0x600–0x7FF IOWAIT3

The CMS pin functions like the other memory select signals, with the same timing and bus request logic. A 1 in the enable bit causes the assertion of the CMS signal at the same time as the selected memory select signal. All enable bits default to 1 at reset, except the BMS bit.

Boot Memory Select (BMS) Disable

The AD73411 also lets you boot the processor from one external memory space while using a different external memory space for BDMA transfers during normal operation. You can use the CMS to select the ﬁrst external memory space for BDMA transfers and BMS to select the second external memory space for booting. The BMS signal can be disabled by setting Bit 3 of the System Control Register to 1. The System Control Register is illustrated in Figure 17.

1514131211109876543210

00000100000 00111

SPORT0 ENABLE

1 = ENABLED 0 = DISABLED

SPORT1 ENABLE

1 = ENABLED 0 = DISABLED

SPORT1 CONFIGURE

1 = SERIAL PORT 0 = FI, FO, IRQ0, IRQ1, SCLK

SYSTEM CONTROL REGISTER

DM (0x3FFF)

PWAIT PROGRAM MEMORY WAIT STATES

BMS ENABLE

0 = ENABLED 1 = DISABLED

Figure 17. System Control Register

Byte Memory

The byte memory space is a bidirectional, 8-bit-wide, external memory space used to store programs and data. Byte memory is accessed using the BDMA feature. The BDMA Control Register is shown in Figure 18. The byte memory space consists of 256 pages, each of which is 16K × 8.

The byte memory space on the AD73411 supports read and write operations as well as four different data formats. The byte memory uses data bits 15:8 for data. The byte memory uses data bits 23:16 and address bits 13:0 to create a 22-bit address. This allows up to a 4 meg × 8 (32 megabit) ROM or RAM to be used without glue logic. All byte memory accesses are timed by the BMWAIT register.

Byte Memory DMA (BDMA, Full Memory Mode)

The Byte memory DMA controller allows loading and storing of program instructions and data using the byte memory space. The BDMA circuit is able to access the byte memory space while the processor is operating normally, and steals only one DSP cycle per 8-, 16-, or 24-bit word transferred.

Composite Memory Select (CMS)

The AD73411 has a programmable memory select signal that is useful for generating memory select signals for memories mapped to more than one space. The CMS signal is generated to have the same timing as each of the individual memory select signals (PMS, DMS, BMS, IOMS) but can combine their functionality.

Each bit in the CMSSEL register, when set, causes the CMS signal to be asserted when the selected memory select is asserted. For example, to use a 32K word memory to act as both program and data memory, set the PMS and DMS bits in the CMSSEL register and use the CMS pin to drive the chip select of the memory; use either DMS or PMS as the additional address bit.

REV. 0

Figure 18. BDMA Control Register

The BDMA circuit supports four different data formats that are selected by the BTYPE register ﬁeld. The appropriate number of 8-bit accesses are done from the byte memory space to build the word size selected. Table XXII shows the data formats supported by the BDMA circuit.

–27–

Page 28

AD73411

Table XXII. Data Formats

Internal

BTYPE Memory Space Word Size Alignment

00 Program Memory 24 Full Word 01 Data Memory 16 Full Word 10 Data Memory 8 MSBs 11 Data Memory 8 LSBs

Unused bits in the 8-bit data memory formats are ﬁlled with 0s. The BIAD register ﬁeld is used to specify the starting address for the on-chip memory involved with the transfer. The 14-bit BEAD register speciﬁes the starting address for the external byte memory space. The 8-bit BMPAGE register speciﬁes the starting page for the external byte memory space. The BDIR register ﬁeld selects the direction of the transfer. Finally the 14-bit BWCOUNT register speciﬁes the number of DSP words to transfer and initiates the BDMA circuit transfers.

BDMA accesses can cross page boundaries during sequential addressing. A BDMA interrupt is generated on the completion of the number of transfers speciﬁed by the BWCOUNT register.

The BWCOUNT register is updated after each transfer so it can be used to check the status of the transfers. When it reaches zero, the transfers have ﬁnished and a BDMA interrupt is generated. The BMPAGE and BEAD registers must not be accessed by the DSP during BDMA operations.

The source or destination of a BDMA transfer will always be on-chip program or data memory.

When the BWCOUNT register is written with a nonzero value, the BDMA circuit starts executing byte memory accesses with wait states set by BMWAIT. These accesses continue until the count reaches zero. When enough accesses have occurred to create a destination word, it is transferred to or from on-chip memory. The transfer takes one DSP cycle. DSP accesses to external memory have priority over BDMA byte memory accesses.

The BDMA Context Reset bit (BCR) controls whether or not the processor is held off while the BDMA accesses are occurring. Setting the BCR bit to 0 allows the processor to continue operations. Setting the BCR bit to 1 causes the processor to stop execution while the BDMA accesses are occurring, to clear the context of the processor and start execution at address 0 when the BDMA accesses have completed.

The BDMA overlay bits specify the OVLAY memory blocks to be accessed for internal memory.

Internal Memory DMA Port (IDMA Port; Host Memory Mode)

The IDMA Port provides an efficient means of communication between a host system and the AD73411. The port is used to access the on-chip program memory and data memory of the DSP with only one DSP cycle per word overhead. The IDMA port cannot be used, however, to write to the DSP’s memorymapped control registers. A typical IDMA transfer process is described as follows:

1. Host starts IDMA transfer.

2. Host checks IACK control line to see if the DSP is busy.

3. Host uses IS and IAL control lines to latch the DMA starting

address (IDMAA) into the DSP’s IDMA control registers. IAD[15] must be set = 0.

4. Host uses IS and IRD (or IWR) to read (or write) DSP inter-

nal memory (PM or DM).

5. Host checks IACK line to see if the DSP has completed the

previous IDMA operation.

6. Host ends IDMA transfer.

The IDMA port has a 16-bit multiplexed address and data bus and supports 24-bit program memory. The IDMA port is completely asynchronous and can be written to while the AD73411 is operating at full speed.

The DSP memory address is latched and then automatically incremented after each IDMA transaction. An external device can therefore access a block of sequentially addressed memory by specifying only the starting address of the block. This increases throughput as the address does not have to be sent for each memory access.

IDMA Port access occurs in two phases. The first is the IDMA Address Latch cycle. When the acknowledge is asserted, a 14-bit address and 1-bit destination type can be driven onto the bus by an external device. The address specifies an on-chip memory location; the destination type specifies whether it is a DM or PM access. The falling edge of the address latch signal latches this value into the IDMAA register.

Once the address is stored, data can either be read from or written to the AD73411’s on-chip memory. Asserting the select line (IS) and the appropriate read or write line (IRD and IWR respectively) signals the AD73411 that a particular transaction is required. In either case, there is a one-processor-cycle delay for synchronization. The memory access consumes one additional processor cycle.

Once an access has occurred, the latched address is automatically incremented and another access can occur.

Through the IDMAA register, the DSP can also specify the starting address and data format for DMA operation. Asserting the IDMA port select (IS) and address latch enable (IAL) directs the AD73411 to write the address onto the IAD0–14 bus into the IDMA Control Register. The IDMAA register, shown below, is memory mapped at address DM (0x3FE0). Note that the latched address (IDMAA) cannot be read back by the host. See Figure 19 for more information on IDMA and DMA memory maps.

IDMA CONTROL (U = UNDEFINED AT RESET)

1514131211109876543210

UUUUUUUUUUUUUUU

IDMAD DESTINATION MEMORY TYPE:

0 = PM 1 = DM

Figure 19. IDMA Control/OVLAY Registers

Bootstrap Loading (Booting)

IDMAA ADDRESS

DM(0x3FE0)

The AD73411 has two mechanisms to allow automatic loading of the internal program memory after reset. The method for booting after reset is controlled by the Mode A, B and C conﬁguration bits.

When the mode pins specify BDMA booting, the AD73411 initiates a BDMA boot sequence when reset is released.

–28–

REV. 0

Page 29

AD73411

When BDMA booting is speciﬁed, the BDMA interface is set up during reset to the following defaults: the BDIR, BMPAGE, BIAD and BEAD registers are set to 0, the BTYPE register is set to 0 to specify program memory 24-bit words, and the BWCOUNT register is set to 32. This causes 32 words of onchip program memory to be loaded from byte memory. These 32 words are used to set up the BDMA to load in the remaining program code. The BCR bit is also set to 1, which causes program execution to be held off until all 32 words are loaded into on-chip program memory. Execution then begins at address 0.

The ADSP-2100 Family Development Software (Revision 5.02 and later) fully supports the BDMA booting feature and can generate byte memory-space-compatible boot code.

The IDLE instruction can also be used to allow the processor to hold off execution while booting continues through the BDMA interface. For BDMA accesses while in Host Mode, the addresses to boot memory must be constructed externally to the AD73411. A0 is the only memory address bit provided by the processor.

IDMA Port Booting

The AD73411 can also boot programs through its Internal DMA port. If Mode C = 1, Mode B = 0 and Mode A = 1, the AD73411 boots from the IDMA port. IDMA feature can load as much onchip memory as desired. Program execution is held off until on-chip program memory location 0 is written to.

Bus Request and Bus Grant (Full Memory Mode)

The AD73411 can relinquish control of the data and address buses to an external device. When the external device requires access to memory, it asserts the bus request (BR) signal. If the AD73411 is not performing an external memory access, it responds to the active BR input in the following processor cycle by:

• Three-stating the data and address buses and the PMS, DMS, BMS, CMS, IOMS, RD, WR output drivers

• Asserting the bus grant (BG) signal

• Halting program execution

If Go Mode is enabled, the AD73411 will not halt program execution until it encounters an instruction that requires an external memory access.

If the AD73411 is performing an external memory access when the external device asserts the BR signal, it will not three-state the memory interfaces or assert the BG signal until the processor cycle after the access completes. The instruction does not need to be completed when the bus is granted. If a single instruction requires two external memory accesses, the bus will be granted between the two accesses.

When the BR signal is released, the processor releases the BG signal, reenables the output drivers and continues program execution from the point at which it stopped.

The bus request feature operates at all times, including when the processor is booting and when RESET is active.

The BGH pin is asserted when the AD73411 is ready to execute an instruction, but is stopped because the external bus is already granted to another device. The other device can release the bus by deasserting bus request. Once the bus is released, the AD73411 deasserts BG and BGH and executes the external memory access.

EZ-ICE® registered trademark of Analog Devices. EZ-Tools™ registered trademark of Analog Devices.

Flag I/O Pins

The AD73411 has eight general-purpose programmable input/ output flag pins. They are controlled by two memory-mapped registers. The PFTYPE register determines the direction, 1 = output and 0 = input. The PFDATA register is used to read and write the values on the pins. Data being read from a pin conﬁgured as an input is synchronized to the AD73411’s clock. Bits that are programmed as outputs will read the value being output. The PF pins default to input during reset.

In addition to the programmable flags, the AD73411 has ﬁve ﬁxed-mode flags, FLAG_IN, FLAG_OUT, FL0, FL1, and FL2. FL0–FL2 are dedicated output flags; FLAG_IN and FLAG_OUT are available as an alternate conﬁguration of SPORT1.

Note: Pins PF0, PF1, PF2, and PF3 are also used for device conﬁguration during reset.

INSTRUCTION SET DESCRIPTION

The AD73411 assembly language instruction set has an algebraic syntax that was designed for ease of coding and readability. The assembly language, which takes full advantage of the processor’s unique architecture, offers the following beneﬁts:

• The algebraic syntax eliminates the need to remember cryptic assembler mnemonics. For example, a typical arithmetic add instruction, such as AR = AX0 + AY0, resembles a simple equation.

• Every instruction assembles into a single, 24-bit word that can execute in a single instruction cycle.

• The syntax is a superset ADSP-2100 Family assembly language and is completely source-and object-code-compatible with other family members. Programs may need to be relocated to utilize on-chip memory and conform to the AD73411’s interrupt vector and reset vector map.

• Sixteen condition codes are available. For conditional jump, call, return, or arithmetic instructions, the condition can be checked and the operation executed in the same instruction cycle.

• Multifunction instructions allow parallel execution of an arithmetic instruction with up to two fetches or one write to processor memory space during a single instruction cycle.

DESIGNING AN EZ-ICE®-COMPATIBLE SYSTEM

The AD73411 has on-chip emulation support and an ICE-Port, a special set of pins that interface to the EZ-ICE. These features allow in-circuit emulation without replacing the target system processor by using only a 14-pin connection from the target system to the EZ-ICE. Target systems must have a 14-pin connector to accept the EZ-ICE’s in-circuit probe, a 14-pin plug. See the ADSP-2100 Family EZ-Tools

™

data sheet for complete

information on ICE products.

Issuing the chip reset command during emulation causes the DSP to perform a full chip reset, including a reset of its memory mode. Therefore, it is vital that the mode pins are set correctly prior to issuing a chip reset command from the emulator user interface. If you are using a passive method of maintaining mode information (as discussed in Setting Memory Modes), it does not matter that the mode information is latched by an emulator reset. However, if using the RESET pin as a method

REV. 0

–29–

Page 30

AD73411

of setting the value of the mode pins, the effects of an emulator reset must be taken into consideration.

One method of ensuring that the values located on the mode pins are those desired, is to construct a circuit like the one shown in Figure 20. This circuit forces the value located on the Mode A pin to logic high; regardless if it is latched via the RESET or ERESET pin.

ERESET RESET

1k⍀

PROGRAMMABLE

I/O

AD73411

MODE A/PFO

Figure 20. Mode A Pin/EZ-ICE Circuit

The ICE-Port interface consists of the following AD73411 pins:

EBR EBG ERESET EMS EINT ECLK

ELIN ELOUT EE

These AD73411 pins must be connected only to the EZ-ICE connector in the target system. These pins have no function except during emulation, and do not require pull-up or pulldown resistors. The traces for these signals between the AD73411 and the connector must be kept as short as possible, no longer than three inches.

The following pins are also used by the EZ-ICE:

BR BG RESET GND

The EZ-ICE uses the EE (emulator enable) signal to take control of the AD73411 in the target system. This causes the processor to use its ERESET, EBR, and EBG pins instead of the RESET, BR, and BG pins. The BG output is three-stated. These signals do not need to be jumper-isolated in your system.

The EZ-ICE connects to your target system via a ribbon cable and a 14-pin female plug. The ribbon cable is 10 inches in length with one end ﬁxed to the EZ-ICE. The female plug is plugged onto the 14-pin connector (a pin strip header) on the target board.

Target Board Connector for EZ-ICE Probe

The EZ-ICE connector (a standard pin strip header) is shown in Figure 21. You must add this connector to your target board design if you intend to use the EZ-ICE. Be sure to allow enough room in your system to ﬁt the EZ-ICE probe onto the 14-pin connector.

The 14-pin, 2-row pin strip header is keyed at the Pin 7 location—you must remove Pin 7 from the header. The pins must be 0.025 inch square and at least 0.20 inch in length. Pin spac-

ing should be 0.1 × 0.1 inches. The pin strip header must have at least 0.15 inch clearance on all sides to accept the EZ-ICE probe plug.

Pin strip headers are available from vendors such as 3M, McKenzie, and Samtec.

GND

EBG

EBR

KEY (NO PIN)

ELOUT

RESET

ⴛ

11 12

13 14

TOP VIEW

EINT

ELIN

ECLK

EMS

ERESET

Figure 21. Target Board Connector for EZ-ICE

Target Memory Interface

For your target system to be compatible with the EZ-ICE emulator, it must comply with the memory interface guidelines listed below.

PM, DM, BM, IOM and CM

Design your Program Memory (PM), Data Memory (DM), Byte Memory (BM), I/O Memory (IOM) and Composite Memory (CM) external interfaces to comply with worst-case device timing requirements and switching characteristics as speciﬁed in the DSP’s data sheet. The performance of the EZ-ICE may approach published worst case speciﬁcation for some memory access timing requirements and switching characteristics.

Note: If your target does not meet the worst-case chip speciﬁcation for memory access parameters, you may not be able to emulate your circuitry at the desired CLKIN frequency. Depending on the severity of the speciﬁcation violation, you may have trouble manufacturing your system as DSP components statistically vary in switching characteristic and timing requirements within published limits.

Restriction: All memory strobe signals on the AD73411 (RD, WR, PMS, DMS, BMS, CMS, and IOMS) used in your target

system must have 10 kΩ pull-up resistors connected when the EZ-ICE is being used. The pull-up resistors are necessary because there are no internal pull-ups to guarantee their state during prolonged three-state conditions resulting from typical EZ-ICE debugging sessions. These resistors may be removed at your option when the EZ-ICE is not being used.

–30–

REV. 0

Page 31

AD73411

Target System Interface Signals

When the EZ-ICE board is installed, the performance on some system signals changes. Design your system to be compatible with the following system interface signal changes introduced by the EZ-ICE board:

• EZ-ICE emulation introduces an 8 ns propagation delay be-

tween your target circuitry and the DSP on the RESET signal.

• EZ-ICE emulation introduces an 8 ns propagation delay

between your target circuitry and the DSP on the BR signal.

• EZ-ICE emulation ignores RESET and BR when single-

stepping.

• EZ-ICE emulation ignores RESET and BR when in Emula-

tor Space (DSP halted).

• EZ-ICE emulation ignores the state of target BR in certain

modes. As a result, the target system may take control of the DSP’s external memory bus only if bus grant (BG) is asserted by the EZ-ICE board’s DSP.

ANALOG FRONT END (AFE) INTERFACING

The AFE section of the AD73411 features a voiceband input/ output channel, each with 16-bit linear resolution. Connectivity to the AFE section from the DSP is uncommitted, thus allowing the user the flexibility of connecting in the mode or conﬁguration of their choice. This section will detail several conﬁgurations— with no extra AFE channels conﬁgured and with two extra AFE channels conﬁgured (using an external AD73322 dual AFE).

DSP SPORT to AFE Interfacing

The SCLK, SDO, SDOFS, SDI and SDIFS pins of SPORT2 must be connected to the Serial Clock, Receive Data, Receive Data Frame Sync, Transmit Data, and Transmit Data Frame Sync pins respectively of either SPORT0 or SPORT1. The SE pin may be controlled from a parallel output pin or flag pin such as FL0–2 or, where SPORT2 power-down is not required, it can be permanently strapped high using a suitable pull-up resistor. The ARESET pin may be connected to the system hardware reset structure or it may also be controlled using a dedicated control line. In the event of tying it to the global system reset, it is advisable to operate the device in mixed mode, which allows a software reset, otherwise there is no convenient way of resetting the AFE section.

of the SE and ARESET signals is synchronized at each device in the cascade. A simple D-type flip-flop is sufﬁcient to sync each signal to the master clock AMCLK, as in Figure 23.

DSP

CONTROL

TO SE

AMCLK

DSP

CONTROL

TO ARESET

AMCLK

Figure 23. SE and

1/2

74HC74

CLK

1/2

74HC74

CLK

ARESET

Sync Circuit for Cascaded

SE SIGNAL SYNCHRONIZED TO AMCLK

ARESET SIGNAL SYNCHRONIZED TO AMCLK

Operation

Connection of a cascade of devices to a DSP, as shown in Figure 24, is no more complicated than connecting a single device. Instead of connecting the SDO and SDOFS to the DSP’s Rx port, these are now daisy-chained to the SDI and SDIFS of the next device in the cascade. The SDO and SDOFS of the ﬁnal device in the cascade are connected to the DSP section’s Rx port to complete the cascade. SE and ARESET on all devices are fed from the signals that were synchronized with the AMCLK using the circuit as described above. The SCLK from only one device need be connected to the DSP section’s SCLK input(s) as all devices will be running at the same SCLK frequency and phase.

AD73411

AMCLK

ARESET

AMCLK

ARESET

DSP

SECTION

FL0

FL1

74HC74

TFS

SCLK

RFS

SDIFS

SDI

SCLK

SDO

SDOFS

SDIFS

SDI

SCLK

SDO

SDOFS

AFE

SECTION

DEVICE 1

ADDITIONAL

AD73322

CODEC

DEVICE 2

SDIFS

SDI

SCLK

SDO

SDOFS

ARESET

AFE

SECTION

DSP

SECTION

TFS

SCLK

RFS

FL0

FL1

Figure 22. AD73411 AFE to DSP Connection

Cascade Operation

Where it is required to conﬁgure extra analog I/O channels to the existing two channels on the AD73411, it is possible to cascade up to seven more channels (using single channel AD73311 or dual channel AD73322 AFEs) by using the scheme described in Figure 24. It is necessary, however, to ensure that the timing

REV. 0

–31–

Figure 24. Connection of an AD73322 Cascaded to AD73411

Interfacing to the AFE’s Analog Inputs and Outputs

The AFE section of the AD73411 offers a flexible interface for microphone pickups, line level signals, or PSTN line interfaces. This section will detail some of the conﬁgurations that can be used with the input and output sections.

The AD73411 features both differential inputs and outputs to provide optimal performance and avoid common-mode noise. It is also possible to interface either inputs or outputs in single-ended mode. This section details the choice of input and output conﬁgurations and also gives some tips toward successful conﬁguration of the analog interface sections.

Page 32

AD73411

ANTIALIAS

FILTER

100⍀

0.047␮F

Analog Inputs

The analog input (encoder) section of the AD73411 can be interfaced to external circuitry in either ac-coupled or dc-coupled modes.

It is also possible to drive the ADC in either differential or single-ended modes. If the single-ended mode is chosen it is possible, using software control, to multiplex between two singleended inputs connected to the positive and negative input pins.

The primary concerns in interfacing to the ADC are to provide adequate antialias ﬁltering and to ensure that the signal source will drive the switched-capacitor input of the ADC correctly. The sigma-delta design of the ADC and its oversampling characteristics simplify the antialias requirements, but it must be remembered that the single-pole RC ﬁlter is primarily intended to eliminate aliasing of frequencies above the Nyquist frequency of the sigma-delta modulator’s sampling rate (typically 2.048 MHz). It may still require a more speciﬁc digital ﬁlter implementation in the DSP to provide the ﬁnal signal frequency response characteristics. It is recommended that for optimum performance the capacitors used for the antialiasing ﬁlter be of high quality dielectric (NPO). The second issue mentioned above is interfacing the signal source to the ADC’s switched capacitor input load. The SC input presents a complex dynamic load to a signal source, therefore, it is important to understand that the slew rate characteristic is an important consideration when choosing external buffers for use with the AD73411.

The AD73411’s on-chip 38 dB preampliﬁer can be enabled when there is not enough gain in the input circuit; the preampliﬁer is conﬁgured by bits IGS0–2 of CRD. The total gain must be conﬁgured to ensure that a full-scale input signal produces a signal level at the input to the sigma-delta modulator of the ADC that does not exceed the maximum input range.

The dc biasing of the analog input signal is accomplished with an on-chip voltage reference. If the input signal is not biased at the internal reference level (via REFOUT), it must be ac-coupled with external coupling capacitors. C The dc biasing of the input can then be accomplished using resistors to REFOUT as in Figures 27 through 29.

VINP

VINN

100⍀

VOUTP

VOUTN

REFOUT

REFCAP

0.1␮F

+6/–15dB

PGA

CONTINUOUS

LOW-PASS

REFERENCE

TIME

FILTER

AD73411

Figure 25. Analog Input (DC-Coupled)

should be 0.1 µF or larger.

0/38dB

PGA

REF

VINP

0/38dB

PGA

REF

AD73411

OPTIONAL

BUFFER

VINN

VOUTP

VOUTN

REFOUT

REFCAP

0.1␮F

+6/–15dB

PGA

CONTINUOUS

LOW-PASS

FILTER

REFERENCE

TIME

Figure 26. Analog Input (DC-Coupled) Using External Ampliﬁers

The AD73411’s ADC inputs are biased about the internal reference level (REFCAP level), therefore, it may be necessary to bias external signals to this level using the buffered REFOUT level as the reference. This is applicable in either dc- or ac-coupled conﬁgurations. In the case of dc coupling, the signal (biased to REFOUT) may be applied directly to the inputs as shown in Figure 25, or it may be conditioned in an external op amp where it can also be biased to the reference level using the buffered REFOUT signal as shown in Figure 26.

In the case of ac-coupling, a capacitor is used to couple the signal to the input of the ADC. The ADC input must be biased to the internal reference (REFCAP) level, which is done by connecting the input to the REFOUT pin through a 10 kΩ resistor as shown in Figure 27.

0.1␮F

10k⍀

100⍀

10k⍀

100⍀

0.047␮F

VOUTP

VOUTN

REFOUT

REFCAP

0.1␮F

VINP

VINN

+6/–15dB

PGA

CONTINUOUS

LOW-PASS

FILTER

REFERENCE

TIME

REF

AD73411

0/38dB

PGA

Figure 27. Analog Input (AC-Coupled) Differential

If the ADC is being connected in single-ended mode, the AD73411 should be programmed for single-ended mode using the SEEN and INV bits of CRF, and the inputs connected as shown in Figure 28. When operated in single-ended input mode, the AD73411 can multiplex one of the two inputs to the ADC input, as shown in Figures 28 and 29.

–32–

REV. 0

Page 33

AD73411

CONTINUOUS

TIME

LOW-PASS

FILTER

REFCAP

REFOUT

REFERENCE

REFCAP

OUT

LOAD

OUT

VINN

VINP

VOUTP

VOUTN

AD73411

+6/–15dB

PGA

0.1␮F

10k⍀

100⍀

0.047 ␮F

VINP

VINN

VOUTP

VOUTN

REFOUT

REFCAP

0.1␮F

+6/–15dB

PGA

CONTINUOUS

LOW-PASS

FILTER

REFERENCE

TIME

0/38dB

PGA

REF

AD73411

Figure 28. Analog Input (AC-Coupled) Single-Ended

VINP

0/38dB

0.1␮F

10k⍀

100⍀

0.047 ␮F

VINN

VOUTP

VOUTN

REFOUT

REFCAP

0.1␮F

+6/–15dB

PGA

CONTINUOUS

LOW-PASS

FILTER

REFERENCE

TIME

PGA

REF

AD73411

Figure 29. Analog Input (AC-Coupled) Single-Ended (Alternate Input)

Interfacing to an Electret Microphone

Figure 30 details an interface for an electret microphone which may be used in some voice applications. Electret microphones typically feature a FET ampliﬁer whose output is accessed on the same lead that supplies power to the microphone; therefore, this output signal must be capacitively coupled to remove the power supply (dc) component. In this circuit the AD73411 input channel is being used in single-ended mode where the inverting ampliﬁer provides suitable gain to scale the input signal relative to the ADC’s full-scale input range. The buffered internal reference level at REFOUT is used via an external buffer to provide power to the electret microphone. This provides a quiet, stable supply for the microphone. If this is not a concern, the microphone can be powered from the system power supply.

VINP

VINN

VOUTP

VOUTN

REFOUT

REFCAP

+6/–15dB

PGA

CONTINUOUS

LOW-PASS

REFERENCE

TIME

FILTER

0/38dB

PGA

REF

MICROPHONE

10␮F

ELECTRET

Analog Output

The AD73411’s differential analog output (VOUT) is produced by an on-chip differential ampliﬁer. The differential output can be ac-coupled or dc-coupled directly to a load that can be a headset or the input of an external ampliﬁer. It is possible to connect the outputs in either a differential or a single-ended conﬁguration, but please note that the effective maximum output voltage swing (peak-to-peak) is halved in the case of single-ended connection. Figure 31 shows a simple circuit providing a differential output with ac coupling. The capacitors in this circuit

) are optional; if used, their value can be chosen as follows:

OUT

2 π

C LOAD

where fC = desired cutoff frequency.

Figure 31. Example Circuit for Differential Output

Figure 32 shows an example circuit for providing a single-ended output with ac coupling. The capacitor of this circuit (C

OUT

) is

not optional if dc current drain is to be avoided.

VINP

VINN

OUT

VOUTP

LOAD

VOUTN

REFOUT

REFCAP

+6/–15dB

PGA

CONTINUOUS

LOW-PASS

FILTER

REFERENCE

TIME

AD73411

Figure 32. Example Circuit for Single-Ended Output

Figure 30. Electret Microphone Interface Circuit

REV. 0

–33–

Page 34

AD73411

Differential-to-Single-Ended Output

In some applications it may be desirable to convert the full differential output of the decoder channel to a single-ended signal. The circuit of Figure 33 shows a scheme for doing this.

VINP

VINN

LOAD

Figure 33. Example Circuit for Differential-to-SingleEnded Output Conversion

Grounding and Layout

As the analog inputs to the AD73411’s AFE section are differential, most of the voltages in the analog modulator are commonmode voltages. The excellent common-mode rejection of the part will remove common-mode noise on these inputs. The analog and digital supplies of the AD73411 are independent and separately pinned out to minimize coupling between analog and digital sections of the device. The digital ﬁlters on the encoder section will provide rejection of broadband noise on the power supplies, except at integer multiples of the modulator sampling frequency. The digital ﬁlters also remove noise from the analog inputs provided the noise source does not saturate the analog modulator. However, because the resolution of the AD73411’s ADC is high, and the noise levels from the AD73411 are so low, care must be taken with regard to grounding and layout.

The printed circuit board that houses the AD73411 should be designed so the analog and digital sections are separated and conﬁned to certain sections of the board. The AD73411 ballout conﬁguration offers a major advantage in that its analog interfaces are conﬁned to the last three rows of the package. This facilitates the use of ground planes that can be easily separated, as shown in Figure 34. A minimum etch technique is generally best for ground planes as it gives the best shielding. Digital and analog ground planes should be joined in only one place. If this connection is close to the device, it is recommended to use a ferrite bead inductor.

REFCAP

VOUTP

VOUTN

REFOUT

REFCAP

+6/–15dB

PGA

CONTINUOUS

LOW-PASS

FILTER

REFERENCE

TIME

AD73411

AFE DIGITAL

DSP

A B C D E F G H J K L M N P R T U

DIGITAL

GROUND PLANE

AFE ANALOG

7 6 5 4 3 2 1

ANALOG

GROUND PLANE

Figure 34. Ground Plane Layout

Avoid running digital lines under the AFE section of the device for they will couple noise onto the die. The analog ground plane should be allowed to run under the AD73411’s AFE section to avoid noise coupling (see Figure 34). The power supply lines to the AD73411 should use as large a trace as possible to provide low impedance paths and reduce the effects of glitches on the power supply lines. Fast switching signals such as clocks should be shielded with digital ground to avoid radiating noise to other sections of the board, and clock signals should never be run near

the analog inputs. Traces on opposite sides of the board should run at right angles to each other. This will reduce the effects of feedthrough through the board. A microstrip technique is by far the best but is not always possible with a double-sided board. In this technique, the component side of the board is dedicated to ground planes while signals are placed on the other side.

Good decoupling is important when using high-speed devices. On the AD73411 both the reference (REFCAP) and supplies need to be decoupled. It is recommended that the decoupling capacitors used on both REFCAP and the supplies, be placed as close as possible to their respective ball connections to ensure high performance from the device. All analog and digital supplies should be decoupled to AGND and DGND respectively, with 0.1 µF ceramic capacitors in parallel with 10 µF tantalum capacitors. The AFE’s digital section supply (DVDD) should be connected to the digital supply that feeds the DSP’s VDD(Ext) connections while the AFE’s digital ground DGND should be returned to the digital ground plane.

–34–

REV. 0

Page 35

TABLE OF CONTENTS

AD73411

Topic Page

FEATURES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

FUNCTIONAL BLOCK DIAGRAM . . . . . . . . . . . . . . . . . 1

GENERAL DESCRIPTION . . . . . . . . . . . . . . . . . . . . . . . . . 1

SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

POWER CONSUMPTION . . . . . . . . . . . . . . . . . . . . . . . . . 5

TIMING CHARACTERISTICS—AFE SECTION . . . . . . . 5

ABSOLUTE MAXIMUM RATINGS . . . . . . . . . . . . . . . . . 6

ORDERING GUIDE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

PBGA BALL CONFIGURATIONS . . . . . . . . . . . . . . . . . . . 6

PBGA BALL FUNCTION DESCRIPTIONS . . . . . . . . . . . 7

ARCHITECTURE OVERVIEW . . . . . . . . . . . . . . . . . . . . . 9

Analog Front End . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

FUNCTIONAL DESCRIPTION . . . . . . . . . . . . . . . . . . . . 10

Encoder Channel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Input Configuration Block . . . . . . . . . . . . . . . . . . . . . . . . 10

Programmable Gain Amplifier . . . . . . . . . . . . . . . . . . . . . 10

ADC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Analog Sigma-Delta Modulator . . . . . . . . . . . . . . . . . . . . 11

Decimation Filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

ADC Coding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Decoder Channel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

DAC Coding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Interpolation Filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Analog Smoothing Filter and PGA . . . . . . . . . . . . . . . . . 12

Differential Output Amplifiers . . . . . . . . . . . . . . . . . . . . . 12

Voltage Reference . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

AFE Serial Port (SPORT2) . . . . . . . . . . . . . . . . . . . . . . . 12

SPORT2 Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

SPORT2 Register Maps . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Master Clock Divider . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Serial Clock Rate Divider . . . . . . . . . . . . . . . . . . . . . . . . . 13

Sample Rate Divider . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

DAC Advance Register . . . . . . . . . . . . . . . . . . . . . . . . . . 14

OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Resetting the AFE Section of the AD73411 . . . . . . . . . . . 14

Power Management . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

AFE Operating Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Program (Control) Mode . . . . . . . . . . . . . . . . . . . . . . . . . 18

Data Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Mixed Program/Data Mode . . . . . . . . . . . . . . . . . . . . . . . 18

Digital Loop-Back . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Sport Loop-Back . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Analog Loop-Back . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

AFE Interfacing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Cascade Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

FUNCTIONAL DESCRIPTION—DSP . . . . . . . . . . . . . . 21

Serial Ports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

DSP SECTION PIN DESCRIPTIONS . . . . . . . . . . . . . . . 22

Memory Interface Pins . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Terminating Unused Pin . . . . . . . . . . . . . . . . . . . . . . . . . 23

Interrupts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Topic Page

LOW-POWER OPERATION . . . . . . . . . . . . . . . . . . . . . . . 24

Power-Down . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Idle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Slow Idle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

SYSTEM INTERFACE . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Clock Signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

MODES OF OPERATION . . . . . . . . . . . . . . . . . . . . . . . . 25

Setting Memory Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

MEMORY ARCHITECTURE . . . . . . . . . . . . . . . . . . . . . . 26

PROGRAM MEMORY . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

Program Memory (Full Memory Mode) . . . . . . . . . . . . . 26

Program Memory (Host Mode) . . . . . . . . . . . . . . . . . . . . 26

DATA MEMORY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

Data Memory (Full Memory Mode) . . . . . . . . . . . . . . . . 26

I/O Space (Full Memory Mode) . . . . . . . . . . . . . . . . . . . . 27

Composite Memory Select (CMS) . . . . . . . . . . . . . . . . . . 27

Boot Memory Select (BMS) Disable . . . . . . . . . . . . . . . . 27

Byte Memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

Byte Memory DMA (BDMA, Full Memory Mode) . . . . . 27

Internal Memory DMA Port (IDMA Port; Host Memory

Mode) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

Bootstrap Loading (Booting) . . . . . . . . . . . . . . . . . . . . . . 29

IDMA Port Booting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

Bus Request and Bus Grant (Full Memory Mode) . . . . . . 29

Flag I/O Pins . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

INSTRUCTION SET DESCRIPTION . . . . . . . . . . . . . . . 29

DESIGNING AN EZ-ICE

Target Board Connector for EZ-ICE Probe . . . . . . . . . . . 30

Target Memory Interface . . . . . . . . . . . . . . . . . . . . . . . . . 30

PM, DM, BM, IOM, and CM . . . . . . . . . . . . . . . . . . . . . 30

Target Systems Interface Signals . . . . . . . . . . . . . . . . . . . 30

ANALOG FRONT END (AFE) INTERFACING . . . . . . . 31

DSP SPORT to AFE Interfacing . . . . . . . . . . . . . . . . . . . 31

Cascade Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

Interfacing to the AFE’s Analog Inputs and Outputs . . . . 31

Analog Inputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

Interfacing to an Electret Microphone . . . . . . . . . . . . . . . 33

Analog Output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

Differential-to-Single-Ended Output . . . . . . . . . . . . . . . . 34

Grounding and Layout . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

OUTLINE DIMENSIONS . . . . . . . . . . . . . . . . . . . . . . . . . 36

-COMPATIBLE SYSTEM . . . 29

REV. 0

–35–

Page 36

AD73411

OUTLINE DIMENSIONS

Dimensions shown in inches and (mm).

119-Ball Plastic Ball Grid Array (PBGA)

B-119

0.089 (2.27)

0.073 (1.85)

0.559 (14.20)

0.543 (13.80)

TOP VIEW

0.874 (22.20)

0.858 (21.80)

DETAIL A

BOTTOM

VIEW

0.050

(1.27)

BSC

0.033

(0.84)

REF

0.028 (0.70)

0.020 (0.50)

SEATING

PLANE

0.300 (7.62) BSC

7 6 5 4 3 2 1

0.126 (3.19) REF

DETAIL A

0.035 (0.90)

0.024 (0.60)

BALL DIAMETER

0.050 (1.27) BSC

A B C D E F G

0.800

H J

(20.32)

BSC

L M N P R T U

0.037 (0.95)

0.033 (0.85)

0.022 (0.56) REF

C01031–5–7/00 (rev. 0)

–36–

PRINTED IN U.S.A.

REV. 0

Datasheet AD73411 Datasheet (Analog Devices)

Specifications and Main Features

Frequently Asked Questions

User Manual