Datasheet AD584 Datasheet (ANALOG DEVICES)

Precision Voltage Reference

AD584

Rev. C

Trademarks and registered trademarks are the property of their respective owners.

1

2 6

7

3 5

8

V+

TAB

4

AD584

TOP VIEW

(Not to S cale)

COMMON

STROBE

V

BG

CAP

2.5V

5.0V

10.0V

00527-001

10.0V

1

5.0V

2

2.5V

3

COMMON

4

V+

8

CAP

7

V

BG

6

STROBE

5

AD584

TOP VIEW

(Not to S cale)

00527-002

Data Sheet

FEATURES

Four programmable output voltages

10.000 V, 7.500 V, 5.000 V, and 2.500 V Laser-trimmed to high accuracies No external components required Trimmed temperature coefficient

15 ppm/°C maximum, 0°C to 70°C (AD584K)

15 ppm/°C maximum, −55°C to +125°C (AD584T) Zero output strobe terminal provided 2-terminal negative reference: capability (5 V and above) Output sources or sinks current Low quiescent current: 1.0 mA maximum 10 mA current output capability MIL-STD-883 compliant versions available

GENERAL DESCRIPTION

The AD584 is an 8-terminal precision voltage reference offering pin programmable selection of four popular output voltages:

10.000 V, 7.500 V, 5.000 V and 2.500 V. Other output voltages, above, below, or between the four standard outputs, are available by the addition of external resistors. The input voltage can vary between 4.5 V and 30 V.

Laser wafer trimming (LWT) is used to adjust the pin programmable output levels and temperature coefficients, resulting in the most flexible high precision voltage reference available in monolithic form.

In addition to the programmable output voltages, the AD584 offers a unique strobe terminal that permits the device to be turned on or off. When the AD584 is used as a power supply reference, the supply can be switched off with a single, low power signal. In the off state, the current drained by the AD584 is reduced to approximately 100 µA. In the on state, the total supply current is typically 750 µA, including the output buffer amplifier.

The AD584 is recommended for use as a reference for 8-, 10-, or 12-bit digital-to-analog converters (DACs) that require an external precision reference. In addition, the device is ideal for analog-to-digital converters (ADCs) of up to 14-bit accuracy, either successive approximation or integrating designs, and in general, it can offer better performance than that provided by standard self-contained references.

Pin Programmable,

PIN CONFIGURATIONS

Figure 1. 8-Pin TO-99

Figure 2. 8-Lead PDIP

The AD584J and AD584K are specified for operation from 0°C to +70°C, and the AD584S and AD584T are specified for the

−55°C to +125°C range. All grades are packaged in a hermetically sealed, eight-terminal TO-99 metal can, and the AD584J and

AD584K are also available in an 8-lead PDI P.

PRODUCT HIGHLIGHTS

1. The flexibility of the AD584 eliminates the need to design-

in and inventory several different voltage references. Furthermore, one AD584 can serve as several references simultaneously when buffered properly.

2. Laser trimming of both initial accuracy and temperature

coefficient results in very low errors overtemperature without the use of external components.

3. The AD584 can be operated in a 2-terminal Zener mode at

a 5 V output and above. By connecting the input and the output, the AD584 can be used in this Zener configuration as a negative reference.

4. The output of the AD584 is configured to sink or source

currents. This means that small reverse currents can be tolerated in circuits using the AD584 without damage to the reference and without disturbing the output voltage (10 V, 7.5 V, and 5 V outputs).

5. The AD584 is available in versions compliant with MIL-STD-

883. Refer to the Analog Devices current AD584/883B data sheet for detailed specifications. This can be found under the Additional Data Sheets section of the AD584 product page.

Information furnishe d by Analog Devices is be lieved to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other rights of third parties that may result from its use. Specifications subject to change without notice. No licen se is granted by implication or otherwise under any patent or patent rights of Analog Devices.

One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A. Tel: 781.329.4700

www.analog.com

AD584 Data Sheet

SPECIFICATIONS

VIN = 15 V and 25°C, unless otherwise noted.

Specifications shown in boldface are tested on all production units at final electrical test. Results from those tests are used to calculate outgoing quality levels. All minimum and maximum specifications are guaranteed; although, only those shown in boldface are tested on all production units.

Table 1.

AD584J AD584K Model Min Typ Max Min Typ Max Unit

OUTPUT VOLTAGE TOLERANCE

Maximum Error at Pin 1 for Nominal

Outputs of

10.000 V

7.500 V

5.000 V

2.500 V

±30 ±20 ±15 ±7.5

±10 ±8 ±6 ±3.5

mV mV mV mV

Maximum Deviation from 25°C Value, T

MIN

10.000 V, 7.500 V, and 5.000 V Outputs

2.500 V Output

1

to T

MAX

30 30

15 15

ppm/°C ppm/°C

Differential Temperature Coefficients Between Outputs 5 3 ppm/°C QUIESCENT CURRENT 0.75

1.0

0.75

1.0

mA

TURN-ON SETTLING TIME TO 0.1% 200 200 µs NOISE (0.1 Hz TO 10 Hz) 50 50 µV p-p LONG-TERM STABILITY 25 25 ppm/1000 Hrs SHORT-CIRCUIT CURRENT 30 30 mA LINE REGULATION (NO LOAD)

15 V ≤ VIN ≤ 30 V

(V

+ 2.5 V) ≤ VIN ≤ 15 V

OUT

0.002

0.005

0.002

0.005

%/V %/V

LOAD REGULATION

0 ≤ I

≤ 5 mA, All Outputs 20

OUT

OUTPUT CURRENT

OUT

Source at 25°C 10 Source T

MIN

to T

5

MAX

50

20

10 5

50

ppm/mA

mA mA

TEMPERATURE RANGE

Operating 0 70 0 70 °C

Storage −65 +175 −65 +175 °C PACKAGE OPTION

8-Lead Plastic Dual In-Line Package (PDIP, N-8) AD584JN AD584KN

1

Calculated as average over the operating temperature range.

Rev. C | Page 3 of 12

AD584 Data Sheet

Specifications shown in boldface are tested on all production units at final electrical test. Results from those tests are used to calculate outgoing quality levels. All minimum and maximum specifications are guaranteed; although, only those shown in boldface are tested on all production units.

Table 2.

AD584S AD584T Model Min Typ Max Min Typ Max Unit

OUTPUT VOLTAGE TOLERANCE

Maximum Error at Pin 1 for Nominal

Outputs of

10.000 V

7.500 V

5.000 V

2.500 V

±30 ±20 ±15 ±7.5

OUTPUT VOLTAGE CHANGE

Maximum Deviation from 25°C Value, T

MIN

10.000 V, 7.500 V, and 5.000 V Outputs

2.500 V Output

1

to T

MAX

30 30

Differential Temperature Coefficients Between Outputs 5 3 ppm/°C

QUIESCENT CURRENT 0.75

1.0

Temperature Variation 1.5 1.5 µA/°C TURN-ON SETTLING TIME TO 0.1% 200 200 µs NOISE (0.1 Hz TO 10 Hz) 50 50 µV p-p LONG-TERM STABILITY 25 25 ppm/1000 Hrs SHORT-CIRCUIT CURRENT 30 30 mA LINE REGULATION (NO LOAD)

15 V ≤ VIN ≤ 30 V

(V

+ 2.5 V) ≤ VIN ≤ 15 V

OUT

0.002

0.005

LOAD REGULATION

0 ≤ I

≤ 5 mA, All Outputs 20

OUT

50

OUTPUT CURRENT

VIN ≥ V

+ 2.5 V

OUT

Source at 25°C 10 10 mA

Source T

Sink T

MIN

to T

MIN

to T

5 5 mA

MAX

5 5 mA

MAX

TEMPERATURE RANGE

Operating −55 +125 −55 +125 °C

Storage −65 +175 −65 +175 °C PACKAGE OPTION

8-Pin Metal Header (TO-99, H-08) AD584SH AD584TH

1

Calculated as average over the operating temperature range.

0.75

20

±10 ±8 ±6 ±3.5

15 20

1.0

0.002

0.005

50

mV mV mV mV

ppm/°C ppm/°C

mA

%/V %/V

ppm/mA

Rev. C | Page 4 of 12

Data Sheet AD584

ABSOLUTE MAXIMUM RATINGS

Table 3.

Parameter Rating

Input Voltage VIN to Ground 40 V Power Dissipation at 25°C 600 mW Operating Junction Temperature Range −55°C to +125°C Lead Temperature (Soldering 10 sec) 300°C Thermal Resistance

Junction-to-Ambient (H-08A) 150°C/W

Stresses above those listed under Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating only; functional operation of the device at these or any other conditions above those indicated in the operational section of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability.

ESD CAUTION

Rev. C | Page 5 of 12

AD584 Data Sheet

AD584

V

SUPPLY

V

OUT

8

1

2

3

6

1.215V

10V

5V

*

2.5V

12kΩ

6kΩ

V

BG

R4

4COMMON

R1

R2

R3

6kΩ

24kΩ

*THE 2.5V TAP IS USED INTE RNALLY AS A BIAS P OINT

AND SHOULD NOT BE CHANGED BY MO RE THAN 100mV IN ANY TRIM CONFIGURAT ION.

00527-004

AD584

V

OUT

1

10.0V

8

V+

4

COMMON

2

5.0V

3

2.5V

6

V

BG

R1

10kΩ

R2

300kΩ

00527-005

R38

R40

Q10

Q16

Q13

Q11

Q14

Q12

Q15

SUB

CAP

R41

R42

R34

R37

R35

R30

R31 R36

Q6

Q8

Q5

C51

C52

C50

Q20

Q7

STROBE

V+

OUT 10V

5V TAP

2.5V TAP

V

BG

V–

R32R33

Q3 Q4

Q2

Q1

R39

00527-006

THEORY OF OPERATION

APPLYING THE AD584

With power applied to Pin 8 and Pin 4 and all other pins open, the AD584 produces a buffered nominal 10.0 V output between Pin 1 and Pin 4 (see Figure 3). The stabilized output voltage can be reduced to 7.5 V, 5.0 V, or 2.5 V by connecting the programming pins as shown in Tab l e 4.

Table 4.

Output Voltage (V) Pin Programming

7.5 Join the 2.5 V (Pin 3) and 5.0 V (Pin 2) pins.

5.0 Connect the 5.0 V pin (Pin 2) to the output pin (Pin 1).

2.5 Connect the 2.5 V pin (Pin 3) to the output pin (Pin 1).

The options shown in Table 4 are available without the use of any additional components. Multiple outputs using only one AD584 can be provided by buffering each voltage programming pin with a unity-gain, noninverting op amp.

approximately 20 V, even for the large values of R1. Do not omit R2; choose its value to limit the output to a value that can be tolerated by the load circuits. If R2 is zero, adjusting R1 to its lower limit results in a loss of control over the output voltage. When precision voltages are set at levels other than the standard outputs, account for the 20% absolute tolerance in the internal resistor ladder.

Alternatively, the output voltage can be raised by loading the

2.5 V tap with R3 alone. The output voltage can be lowered by connecting R4 alone. Either of these resistors can be a fixed resistor selected by test or an adjustable resistor. In all cases, the resistors should have a low temperature coefficient to match the

AD584 internal resistors, which have a negative temperature

coefficient less than 60 ppm/°C. If both R3 and R4 are used, these resistors should have matching temperature coefficients.

When only small adjustments or trims are required, the circuit in Figure 4 offers better resolution over a limited trim range. The circuit can be programmed to 5.0 V, 7.5 V, or 10 V, and it can be adjusted by means of R1 over a range of about ±200 mV. To trim the 2.5 V output option, R2 (see Figure 4) can be reconnected to the band gap reference (Pin 6). In this configuration, limit the adjustment to ±100 mV to avoid affecting the performance of the AD584.

Figure 3. Variable Output Options

The AD584 can also be programmed over a wide range of output voltages, including voltages greater than 10 V, by the addition of one or more external resistors. Figure 3 illustrates the general adjustment procedure, with approximate values given for the internal resistors of the AD584. The AD584 may be modeled as an op amp with a noninverting feedback connection, driven by a high stability 1.215 V band gap reference (see Figure 5 for schematic).

When the feedback ratio is adjusted with external resistors, the output amplifier can be made to multiply the reference voltage by almost any convenient amount, making popular outputs of

10.24 V, 5.12 V, 2.56 V, or 6.3 V easy to obtain. The most general adjustment (which gives the greatest range and poorest resolution) uses R1 and R2 alone (see Figure 3). As R1 is adjusted to its upper limit, the 2.5V pin (Pin 3) is connected to the output, which reduces to 2.5 V. As R1 is adjusted to its lower limit, the output voltage rises to a value limited by R2. For example, if R2 is approximately 6 kΩ, the upper limit of the output range is

Figure 4. Output Trimming

Figure 5. Schematic Diagram

Rev. C | Page 6 of 12

Data Sheet AD584

10.005

10.000

9.995 –55 0 25 70 125

V

OUT

(V)

TEMPERATURE (°C)

00527-007

OUTPUT CURRE NT (mA)

OUTPUT VOLTAGE (V)

0 5 10 15 20–5–10–15

SINKSOURCE

–20

14

12

10

8

6

4

2

0

+VS = 15V T

A

= 25°C

00527-008

SETTLING TIME (µs)

100 150 200 250500

10.03V

10.02V

12V

11V

10V

20V

10V

0V

10.01V

10.00V

OUTPUT

POWER

SUPPLY

INPUT

00527-009

PERFORMANCE OVER TEMPERATURE

Each AD584 is tested at three temperatures over the −55°C to +125°C range to ensure that each device falls within the maximum error band (see Figure 6) specified for a particular grade (that is, S and T grades); three-point measurement guarantees performance within the error band from 0°C to 70°C (that is, J and K grades). The error band guaranteed for the AD584 is the maximum deviation from the initial value at 25°C. Thus, given the grade of the AD584, the maximum total error from the initial tolerance plus the temperature variation can easily be determined. For example, for the AD584T, the initial tolerance is ±10 mV, and the error band is ±15 mV. Therefore, the unit is guaranteed to be 10.000 V ± 25 mV from −55°C to +125°C.

supply or ground. Figure 7 shows the output voltage vs. the output current characteristics of the device. Source current is displayed as negative current in the figure, and sink current is displayed as positive current. The short-circuit current (that is, 0 V output) is about 28 mA; however, when shorted to 15 V, the sink current goes to approximately 20 mA.

Figure 6. Typical Temperature Characteristic

OUTPUT CURRENT CHARACTERISTICS

The AD584 has the capability to either source or sink current and provide good load regulation in either direction; although, it has better characteristics in the source mode (positive current into the load). The circuit is protected for shorts to either positive

Figure 7. Output Voltage vs. Output Current (Sink and Source)

DYNAMIC PERFORMANCE

Many low power instrument manufacturers are becoming increasingly concerned with the turn-on characteristics of the components being used in their systems. Fast turn-on components often enable the end user to keep power off when not needed and yet respond quickly when the power is turned on. Figure 8 displays the turn-on characteristic of the AD584. Figure 8 is generated from cold-start operation and represents the true turn-on waveform after an extended period with the supplies off. Figure 8 shows both the coarse and fine transient characteristics of the device; the total settling time to within ±10 mV is about 180 µs, and there is no long thermal tail appearing after the point.

Figure 8. Output Settling Characteristic

Rev. C | Page 7 of 12

AD584 Data Sheet

AD584

1

10.0V

8

SUPPLY

V+

4

COMMON

7

CAP

6

V

BG

0.01µF* TO

0.1µF

*INCREASES T URN- ON TIME

00527-010

1000

100

1

10

10 100 1k 10k 100k 1M

FREQUENCY ( Hz )

NOISE SPECTRAL DENSITY (nV/ Hz)

TOTAL NOISE (µV rms) UP TO

SPECIFIED FREQUENCY

NO CAP

100pF

1000pF

0.01µF

00527-011

AD584

1

10.0V

2

3

8

V+

4

COMMON

5

STROBE

10kΩ

20kΩ

2N2222

100Ω

LOGIC

INPUT

HI = OFF LO = ON

00527-012

AD584

1

10.0V

V

OUT

10V @ 4A

8

V+

4

COMMON

470Ω

0.1µF

VIN ≥ 15V

2N6040

00527-013

NOISE FILTERING

The bandwidth of the output amplifier in the AD584 can be reduced to filter output noise. A capacitor ranging between 0.01 µF and 0.1 µF connected between the CAP and V reduces the wideband and feedthrough noise in the output of the AD584, as shown in Figure 9 and Figure 10. However, this tends to increase the turn-on settling time of the device; therefore, allow for ample warm-up time.

terminals further

BG

USING THE STROBE TERMINAL

The AD584 has a strobe input that can be used to zero the output. This unique feature permits a variety of new applications in signal and power conditioning circuits.

Figure 11 illustrates the strobe connection. A simple NPN switch can be used to translate a TTL logic signal into a strobe of the output. The AD584 operates normally when there is no current drawn from Pin 5. Bringing this terminal low, to less than 200 mV, allows the output voltage to go to zero. In this mode, the AD584 is not required to source or sink current (unless a 0.7 V residual output is permissible). If the AD584 is required to sink a transient current while strobe is off, limit the strobe terminal input current by a 100 Ω resistor, as shown in Figure 11.

Figure 9. Additional Noise Filtering wit h an External Capacitor

Figure 10. Spectral Noise Density and Total RMS Noise vs. Frequency

Figure 11. Use of the Strobe Terminal

The strobe terminal tolerates up to 5 µA leakage, and its driver should be capable of sinking 500 µA continuous. A low leakage, open collector gate can be used to drive the strobe terminal d ire c t ly, provided the gate can withstand the AD584 output voltage plus 1 V.

PERCISION HIGH CURRENT SUPPLY

The AD584 can be easily connected to a power PNP or power PNP Darlington device to provide much greater output current capability. The circuit shown in Figure 12 delivers a precision 10 V output with up to 4 A supplied to the load. If the load has a

Rev. C | Page 8 of 12

significant capacitive component, the 0.1 µF capacitor is required. If the load is purely resistive, improved high frequency, supply rejection results from removing the capacitor.

Figure 12. High Current Precision Supply

Data Sheet AD584

AD584

1

10.0V

5.0V

2.5V

2

3

8

V+

4

COMMON

DARLINGTON NPN 2N6057

V

OUT

(5V, 12A AS SHOWN)

1kΩ

RAW SUPPLY (≈5V > V

OUT

)

00527-014

AD584

1

V

OUT

= 2.5V

2.5V TAP

3

8

V+

4

COMMON

=

i

+ 0.75mA

2.5V R

R

LOAD

00527-015

AD584

1

V

OUT

V

REF

–5V

5.0V TAP

2

8

V+

4

COMMON

–15V

R

S

2.4kΩ

5%

ANALOG GND

1µF

00527-016

AD584

10.0V

V+

1

8

4

COMMON

+15V

AD7533

4

BIT 1 (MSB)

5

DIGITAL

INPUT

13

16

1

2

BIT 10 (LS B)

15314

V

REF

+15V

–15V

V

OUT

0V TO –10V

R

FB

I

OUT

1

I

OUT

2

COMMON

00527-017

The AD584 can also use an NPN or NPN Darlington transistor to boost its output current. Simply connect the 10 V output terminal of the AD584 to the base of the NPN booster and take the output from the booster emitter, as shown in Figure 13. The

5.0V pin or the 2.5V pin must connect to the actual output in this configuration. Variable or adjustable outputs (as shown in Figure 3 and Figure 4) can be combined with a 5.0 V connection to obtain outputs above 5.0 V.

The temperature characteristics and long-term stability of the device is essentially the same as that of a unit used in standard 3-terminal mode.

Figure 13. NPN Output Current Booster

THE AD584 AS A CURRENT LIMITER

The AD584 represents an alternative to current limiter diodes that require factory selection to achieve a desired current. Use of current limiting diodes often results in temperature coefficients of 1%/°C. Use of the AD584 in this mode is not limited to a set current limit; it can be programmed from 0.75 mA to 5 mA with the insertion of a single external resistor (see Figure 14). The minimum voltage required to drive the connection is 5 V.

Figure 14. A Two-Component Precision Current Limiter

Figure 15. 2-Terminal, −5 V Reference

The AD584 can also be used in 2-terminal mode to develop a positive reference. V

and V

IN

are tied together and to the

OUT

positive supply through an appropriate supply resistor. The performance characteristics are similar to those of a negative 2-terminal connection. The only advantage of this connection over the standard 3-terminal connection is that a lower primary supply can be used, as low as 0.5 V above the desired output voltage. This type of operation requires considerable attention to load and to the primary supply regulation to ensure that the

AD584 always remains within its regulating range of 1 mA to

5 mA (2 mA to 5 mA for operation beyond 85°C).

10 V REFERENCE WITH MULTIPLYING CMOS DACs OR ADCs

The AD584 is ideal for application with the AD7533 10-bit multiplying CMOS DAC, especially for low power applications. It is equally suitable for the

AD7574 8-bit ADC.

hook-up, as shown in Figure 16, the standard output voltages are inverted by the amplifier/DAC configuration to produce converted voltage ranges. For example, a +10 V reference produces a 0 V to

−10 V range. If an OP1177 amplifier is used, total quiescent supply current is typically 2 mA.

In the standard

NEGATIVE REFERENCE VOLTAGES FROM AN AD584

The AD584 can also be used in a 2-terminal Zener mode to provide a precision −1 0 V, −7.5 V, or −5.0 V reference. As shown in Figure 15, the V the positive supply (in this case, ground). The AD584 COMMON pin is connected through a resistor to the negative supply. The output is now taken from the COMMON pin instead of V 1 mA flowing through the AD584 in this mode, a typical unit shows a 2 mV increase in the output level over that produced in 3-terminal mode. Also, note that the effective output impedance in this connection increases from 0.2 Ω typical to 2 Ω. It is essential to arrange the output load and the supply resistor, R the net current through the AD584 is always between 1 mA and 5 mA (between 2 mA and 5 mA for operation beyond 85°C).

and V

IN

terminals are connected together to

OUT

, so that

S

. With

Figure 16. Low Power 10-Bit CMOS DAC Application

Rev. C | Page 9 of 12

AD584 Data Sheet

–10V REF

AD584

4

1

8

–15V

V+

10.0V

COMMON

R3

1.2kΩ

5%

0.1µF

+15V

1 18 2 3 4 5

AD7574

(TOP VIEW)

SIGNAL

INPUT

0V TO +10V

ANALOG

GROUND

GROUND INTERTIE

DIGITAL SUPPLY RETURN

R1

2kΩ 10%*

*R1 AND R2 CAN BE OMITT E D IF

GAIN TRIM IS NOT REQUIRED.

GAIN TRIM

R2 2kΩ*

00527-019

C

A1 (MSB) 5

14

A2 6

15

A3 7 A4 8 A5 9 A6 10 A7 11

4

I

O

A8 (LSB) 12

COMP 16

1 V

LC

R

L

R15

R14 = R15

V+

13

V–

3

2

AD

DAC08

V

REF

(+)

V

REF

(–)

AD584

4

8

1

3

COMMON

V+

2.5V

10.0V

R14

00527-020

I

OUT

00527-018

0.5mA I

REF

DAC

AD565A

5kΩ

20V SPAN

10V SPAN

DAC OUT

–V

EE

REF

GND

BIPOLAR OFF

5kΩ

8kΩI

O

CODE INPUT

LSBMSB

10V

V

CC

REF OUT

REF

IN

POWER

GND

19.95kΩ

20kΩ

9.95kΩ

I

OUT

=

4 × I

REF

× CODE

0.1µF

OP1177

+15V

–15V

2

3

6

OP AMP OUTPUT ±10V

+15V

1

4

8

AD584

R2

100Ω

15T

GAIN

ADJUST

R1

100Ω

15T

BIPOLAR OFFSET

ADJUST

–15V

The AD584 is normally used in the −10 V mode with the AD7574 to give a 0 V to +10 V ADC range. This is shown in Figure 17. Bipolar output applications and other operating details can be found in the data sheets for the CMOS products.

scale temperature coefficient of 18 ppm/°C more than the commercial range. The 10 V reference also supplies the normal 1 mA bipolar offset current through the 9.95 kΩ bipolar offset resistor. The bipolar offset temperature coefficient thus depends only on the temperature coefficient matching of the bipolar offset resistor to the input reference resistor and is guaranteed to 3 ppm/°C. Figure 18 demonstrates the flexibility of the AD584 applied to another popular digital-to-analog configuration.

Figure 17. AD584 as −10 V Reference for CMOS ADC

PRECISION DAC REFERENCE

The AD565A, like many DACs, can operate with an external 10 V reference element (see Figure 19). This 10 V reference voltage is converted into a reference current of approximately

0.5 mA via the internal 19.95 kΩ resistor (in series with the external 100 Ω trimmer). The gain temperature coefficient of the AD565A is primarily governed by the temperature tracking of the 19.95 kΩ resistor and the 5 kΩ/10 kΩ span resistors; this gain temperature coefficient is guaranteed to 3 ppm/°C. Therefore, using the AD584K (at 5 ppm/°C) as the 10 V reference guarantees a maximum full-

Figure 18. Current Output, 8-Bit Digital-to-Analog Configuration

Figure 19. Precision 12-Bit DAC

Rev. C | Page 10 of 12

Data Sheet AD584

CONTROLLING DIMENSIONSARE IN INCHES; MILLIMETER DIMENSIONS (IN PARENTHESES) ARE ROUNDED-OFF INCH EQUIVALENTS FOR REFERENCE O NLYAND ARE NOT APPROPRIATE FOR USE IN DESIGN.

COMPLI ANT TO JE DE C S TANDARDS MO-002- AK

0.2500 (6.35) MIN

0.5000 (12.70) MIN

0.1850 (4.70)

0.1650 (4.19)

REFERENCE PLANE

0.0500 (1.27) MAX

0.0190 (0.48)

0.0160 (0.41)

0.0210 (0.53)

0.0160 (0.41)

0.0400 (1.02)

0.0100 (0.25)

0.0400 (1.02) MAX

0.0340 (0.86)

0.0280 (0.71)

0.0450 (1.14)

0.0270 (0.69)

0.1600 (4.06)

0.1400 (3.56)

0.1000 (2.54) BSC

6

2

8

7

5

4

3

1

0.2000 (5.08)

BSC

0.1000 (2.54)

BSC

0.3700 (9.40)

0.3350 (8.51)

0.3050 (7.75)

45° BSC

BASE & SEATING PLANE

022306-A

COMPLIANT TO JEDEC STANDARDS MS-001

CONTROLLING DIMENSIONSARE IN INCHES; MILLIMETER DIMENSIONS (IN PARENTHESES) ARE ROUNDED-OFF INCH EQUIVALENTS FOR REFERENCE O NLYAND ARE NOT APPROPRIATE FOR USE IN DESIGN. CORNER LEADS MAY BE CONFIGURED AS WHOLE OR HALF LEADS .

070606-A

0.022 (0.56)

0.018 (0.46)

0.014 (0.36)

SEATING PLANE

0.015 (0.38) MIN

0.210 (5.33) MAX

0.150 (3.81)

0.130 (3.30)

0.115 (2.92)

0.070 (1.78)

0.060 (1.52)

0.045 (1.14)

8

1

4

5

0.280 (7.11)

0.250 (6.35)

0.240 (6.10)

0.100 (2.54) BSC

0.400 (10.16)

0.365 (9.27)

0.355 (9.02)

0.060 (1.52) MAX

0.430 (10.92) MAX

0.014 (0.36)

0.010 (0.25)

0.008 (0.20)

0.325 (8.26)

0.310 (7.87)

0.300 (7.62)

0.195 (4.95)

0.130 (3.30)

0.115 (2.92)

0.015 (0.38) GAUGE

PLANE

0.005 (0.13) MIN

OUTLINE DIMENSIONS

Figure 20. 8-Pin Metal Header [TO-99]

(H-08)

Dimensions shown in inches and (millimeters)

Figure 21. 8-Lead Plastic Dual In-Line Package [PDIP]

Narrow Body (N-8)

Dimensions shown in inches and (millimeters)

Rev. C | Page 11 of 12

AD584 Data Sheet

Initial Accuracy

AD584KH

5.0

±6.0

0.12

15

0 to 70

8-Pin TO-99

H-08

100

ORDERING GUIDE

Output

Model1

Voltage (VO)

mV %

AD584JH 2.5 ±7.5 0.30 30 0 to 70 8-Pin TO-99 H-08 100 AD584JNZ 2.5 ±7.5 0.30 30 0 to 70 8-Lead PDIP N-8 50 AD584KH 2.5 ±3.5 0.14 15 0 to 70 8-Pin TO-99 H-08 100 AD584KNZ 2.5 ±3.5 0.14 15 0 to 70 8-Lead PDIP N-8 50 AD584SH 2.5 ±7.5 0.30 30 −55 to +125 8-Pin TO-99 H-08 100 AD584SH/883B 2.5 ±7.5 0.30 30 −55 to +125 8-Pin TO-99 H-08 100 AD584TH 2.5 ±3.5 0.14 20 −55 to +125 8-Pin TO-99 H-08 100 AD584TH/883B 2.5 ±3.5 0.14 20 −55 to +125 8-Pin TO-99 H-08 100 AD584JH 5.0 ±15.0 0.30 30 0 to 70 8-Pin TO-99 H-08 100 AD584JNZ 5.0 ±15.0 0.30 30 0 to 70 8-Lead PDIP N-8 50

AD584KNZ 5.0 ±6.0 0.12 15 0 to 70 8-Lead PDIP N-8 50 AD584SH 5.0 ±15.0 0.14 30 −55 to +125 8-Pin TO-99 H-08 100 AD584SH/883B 5.0 ±15.0 0.30 30 −55 to +125 8-Pin TO-99 H-08 100 AD584TH 5.0 ±6.0 0.30 15 −55 to +125 8-Pin TO-99 H-08 100 AD584TH/883B 5.0 ±6.0 0.12 15 −55 to +125 8-Pin TO-99 H-08 100 AD584JH 7.5 ±20.0 0.27 30 0 to 70 8-Pin TO-99 H-08 100 AD584JNZ 7.5 ±20.0 0.27 30 0 to 70 8-Lead PDIP N-8 50 AD584KH 7.5 ±8.0 0.11 15 0 to 70 8-Pin TO-99 H-08 100 AD584KNZ 7.5 ±8.0 0.11 15 0 to 70 8-Lead PDIP N-8 50 AD584SH 7.5 ±20.0 0.27 30 −55 to +125 8-Pin TO-99 H-08 100 AD584SH/883B 7.5 ±20.0 0.27 30 −55 to +125 8-Pin TO-99 H-08 100 AD584TH 7.5 ±8.0 0.11 15 −55 to +125 8-Pin TO-99 H-08 100 AD584TH/883B 7.5 ±8.0 0.11 15 −55 to +125 8-Pin TO-99 H-08 100 AD584JH 10.0 ±30.0 0.30 30 0 to 70 8-Pin TO-99 H-08 100 AD584JNZ 10.0 ±30.0 0.30 30 0 to 70 8-Lead PDIP N-8 50 AD584KH 10.0 ±10.0 0.10 15 0 to 70 8-Pin TO-99 H-08 100 AD584KNZ 10.0 ±10.0 0.10 15 0 to 70 8-Lead PDIP N-8 50 AD584SH 10.0 ±30.0 0.30 30 −55 to +125 8-Pin TO-99 H-08 100 AD584SH/883B 10.0 ±30.0 0.30 30 −55 to +125 8-Pin TO-99 H-08 100 AD584TH 10.0 ±10.0 0.10 15 −55 to +125 8-Pin TO-99 H-08 100 AD584TH/883B 10.0 ±10.0 0.10 15 −55 to +125 8-Pin TO-99 H-08 100

1

Z = RoHS Compliant Part.

Temperature Coefficient (ppm/°C)

Temperature Range (°C)

Package Description

Package Option

Ordering Quantity

registered trademarks are the property of their respective owners. D00527-0-5/12(C)

Rev. C | Page 12 of 12

Datasheet AD584 Datasheet (ANALOG DEVICES)

Specifications and Main Features

Frequently Asked Questions

User Manual

FEATURES

GENERAL DESCRIPTION

PIN CONFIGURATIONS

PRODUCT HIGHLIGHTS

TABLE OF CONTENTS

REVISION HISTORY

SPECIFICATIONS

ABSOLUTE MAXIMUM RATINGS

ESD CAUTION

THEORY OF OPERATION

APPLYING THE AD584

PERFORMANCE OVER TEMPERATURE

OUTPUT CURRENT CHARACTERISTICS

DYNAMIC PERFORMANCE

NOISE FILTERING

USING THE STROBE TERMINAL

PERCISION HIGH CURRENT SUPPLY

THE AD584 AS A CURRENT LIMITER

10 V REFERENCE WITH MULTIPLYING CMOS DACs OR ADCs

NEGATIVE REFERENCE VOLTAGES FROM AN AD584

PRECISION DAC REFERENCE

OUTLINE DIMENSIONS

ORDERING GUIDE