Page 1
Multiplying DACs with Serial Interface
AD5444/AD5446
Rev. D
Trademarks and registered trademarks are the property of their respective owners.
04588-001
POWER-ON
RESET
GND
V
REF
R
FB
I
OUT
1
I
OUT
2
R
SDO
CONTROL LOGIC AND
INPUT SHIFT REGISTER
DAC REGIST E R
12-BIT
R-2R DAC
INPUT LATCH
SCLK
SDIN
SYNC
V
DD
AD5444/
AD5446
Data Sheet
FEATURES
12 MHz multiplying bandwidth
INL of ± 0.5 LSB at 12 bits
Pin-compatible 12-/14-bit current output DAC
2.5 V to 5.5 V supply operation
10-lead MSOP package
±10 V reference input
50 MHz serial interface
2.7 MSPS update rate
Extended temperature range: −40°C to +125°C
4-quadrant multiplication
Power-on reset with brownout detection
0.4 µA typical current consumption
Guaranteed monotonic
APPLICATIONS
Portable, battery-powered applications
Waveform generators
Analog processing
Instrumentation applications
Programmable amplifiers and attenuators
Digitally controlled calibration
Programmable filters and oscillators
Composite video
Ultrasound
Gain, offset, and voltage trimming
Automotive radar
12-/14-Bit High Bandwidth
GENERAL DESCRIPTION
The AD5444/AD54461 are CMOS 12-bit and 14-bit, current
output, digital-to-analog converters (DACs). Operating from a
single 2.5 V to 5.5 V power supply, these devices are suited for
battery-powered and other applications.
As a result of the CMOS submicron manufacturing process,
these parts offer excellent 4-quadrant multiplication characteristics of up to 12 MHz.
These DACs use a double-buffered, 3-wire serial interface that
is compatible with SPI®, QSPI™, MICROWIRE™, and most DSP
interface standards. On power-up, the internal shift register and
latches are filled with 0s, and the DAC output is at zero scale.
The applied external reference input voltage (V
the full-scale output current. These parts can handle ±10 V
inputs on the reference, despite operating from a single-supply
power supply of 2.5 V to 5.5 V. An integrated feedback resistor
(R
) provides temperature tracking and full-scale voltage output
FB
when combined with an external current-to-voltage precision
amplifier. The AD5444/AD5446 DACs are available in small
10-lead MSOP packages, which are pin-compatible with the
AD5425/AD5426/AD5432/AD5443 family of DACs.
The E VA L-AD5446SDZ board is available for evaluating DAC
performance. For more information, see the UG-327 evaluation
board user guide.
1
US Patent Number 5,689,257.
) determines
REF
FUNCTIONAL BLOCK DIAGRAM
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Figure 1.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781.329.4700
Fax: 781.461.3113 ©2004–2012 A
nalog Devices, Inc. All rights reserved.
www.analog.com
Page 2
AD5444/AD5446 Data Sheet
TABLE OF CONTENTS
Features .............................................................................................. 1
Applications ....................................................................................... 1
General Description ......................................................................... 1
Functional Block Diagram .............................................................. 1
Revision History ............................................................................... 2
Specifications ..................................................................................... 3
Timing Characteristics ................................................................ 5
Absolute Maximum Ratings ............................................................ 6
ESD Caution .................................................................................. 6
Pin Configuration and Function Descriptions ............................. 7
Typical Performance Characteristics ............................................. 8
Terminology .................................................................................... 14
General Description ....................................................................... 15
REVISION HISTORY
4/12—Rev. C to Rev. D
Changes to General Description Section ...................................... 1
Deleted Evaluation Board for the DAC Section ......................... 23
Deleted Power Supplies for the Evaluation Board Section ....... 23
Deleted Figure 54; Renumbered Sequentially............................. 24
Deleted Figure 55 and Figure 56 ................................................... 25
Updated Outline Dimensions ....................................................... 25
Changes to Ordering Guide .......................................................... 25
Deleted Figure 57 ............................................................................ 26
4/07—Rev. B to Rev. C
Changes to Table 9 ................................
Changes to Ordering Guide .......................................................... 28
Changes to Features .......................................................................... 1
Changes to General Description .................................................... 1
Changes to Table 1 ............................................................................ 3
Changes to Figure 22 ...................................................................... 10
Changes to Figure 23 ...................................................................... 10
Changes to Table 9 .......................................................................... 19
Changes to Table 1 2 ........................................................................ 27
Updated Outline Dimensions ....................................................... 28
Changes to Ordering Guide .......................................................... 28
.......................................... 19
DAC Section................................................................................ 15
Circuit Operation ....................................................................... 15
Single-Supply Applications ....................................................... 17
Adding Gain ................................................................................ 17
Divider or Programmable Gain Element ................................ 17
Amplifier Selection .................................................................... 18
Reference Selection .................................................................... 18
Serial Interface ................................................................................ 20
Microprocessor Interfacing ....................................................... 21
PCB Layout and Power Supply Decoupling ................................ 23
Overview of AD54xx and AD55xx Current Output Devices ... 24
Outline Dimensions ....................................................................... 25
Ordering Guide .......................................................................... 25
4/05—Rev. 0 to Rev. A
Added AD5446 ................................................................... Universal
Changes to Features .......................................................................... 1
Changes to General Description ..................................................... 1
Changes to Specifications ................................................................. 3
Inserted Figure 7; Renumbered Sequentially................................. 9
Inserted Figure 9; Renumbered Sequentially................................. 9
Inserted Figure 13; Renumbered Sequentially ........................... 10
Changes to Figure 22 ...................................................................... 11
Changes to Figure 23 ...................................................................... 11
Changes to Serial Interface ............................................................ 20
Changes to Figure 44 ...................................................................... 20
Changes to Figure 45 ...................................................................... 20
Updated Outline Dimensions ....................................................... 28
Changes to Ordering Guide .......................................................... 28
10/04—Revision 0: Initial Version
Rev. D | Page 2 of 28
Page 3
Data Sheet AD5444/AD5446
STATIC PERFORMANCE
Total Unadjusted Error (TUE)
±1
LSB
OUT
OUT
REF
RFB Feedback Resistance
7 9 11
kΩ
Input resistance TC = −50 ppm/°C
Output High Voltage, VOH
VDD − 1
V
VDD = 4.5 V to 5 V, I
SOURCE
= 200 µA
SOURCE
SINK
SINK
±10
nA
TA = −40°C to +125°C
SPECIFICATIONS
VDD = 2.5 V to 5.5 V, V
unless otherwise noted. DC performance measured with OP177, and ac performance measured with AD8038, unless otherwise noted.
Table 1.
Parameter Min Typ Max Unit Conditions
AD5444
Resolution 12 Bits
Relative Accuracy ±0.5 LSB
Differential Nonlinearity ±1 LSB Guaranteed monotonic
Gain Error ±0.5 LSB
AD5446
Resolution 14 Bits
Relative Accuracy ±2 LSB
Differential Nonlinearity −1/+2 LSB Guaranteed monotonic
Total Unadjusted Error (TUE) ±4 LSB
Gain Error ±2.5 LSB
Gain Error Temperature Coefficient1 ±2 ppm FSR/°C
Output Leakage Current ±1 nA Data = 0x0000, TA = 25°C, I
±10 nA Data = 0x0000, TA = −40°C to +125°C, I
REFERENCE INPUT1
Reference Input Range ±10 V
V
Input Resistance 7 9 11 kΩ Input resistance TC = −50 ppm/°C
= 10 V, I
REF
2 = 0 V. Temperature range for Y version: −40°C to +125°C. All specifications T
OUT
1
MIN
to T
MAX
,
1
Input Capacitance
Zero-Scale Code 18 22 pF
Full-Scale Code 18 22 pF
DIGITAL INPUTS/OUTPUTS1
Input High Voltage, VIH 2.0 V VDD = 3.6 V to 5 V
1.7 V VDD = 2.5 V to 3.6 V
Input Low Voltage, VIL 0.8 V VDD = 2.7 V to 5.5 V
0.7 V VDD = 2.5 V to 2.7 V
VDD − 0.5 V VDD = 2.5 V to 3.6 V, I
Output Low Voltage, VOL 0.4 V VDD = 4.5 V to 5 V, I
0.4 V VDD = 2.5 V to 3.6 V, I
Input Leakage Current, IIL ±1 nA TA = 25°C
Input Capacitance 10 pF
= 200 µA
= 200 µA
= 200 µA
Rev. D | Page 3 of 28
Page 4
AD5444/AD5446 Data Sheet
REF
REF
64
dB
1 MHz
Measured to ±16 mV of FS
16
33
ns
REF
LOAD
REF
OUT
OUT
alternate loading of all 0s and all 1s
REF
REF
OUT
OUT
REF
OUT
OUT
REF
OUT
OUT
Intermodulation Distortion
79 dB
f1 = 20 kHz, f2 = 25 kHz, clock = 1 MHz, V
REF
= 3.5 V
Power Supply Range, VDD
2.5 5.5 V
Parameter Min Typ Max Unit Conditions
DYNAMIC PERFORMANCE1
Reference Multiplying Bandwidth 12 MHz V
Multiplying Feedthrough Error V
72 dB 100 kHz
44 dB 10 MHz
Output Voltage Settling Time V
Measured to ±1 mV of FS 100 110 ns
Measured to ±4 mV of FS 24 40 ns
Digital Delay 20 40 ns Interface delay time
10%-to-90% Settling Time 10 30 ns Rise and fall time, V
Digital-to-Analog Glitch Impulse 2 nV-s 1 LSB change around major carry, V
Output Capacitance
I
1 13 pF DAC latches loaded with all 0s
28 pF DAC latches loaded with all 1s
I
2 18 pF DAC latches loaded with all 0s
5 pF DAC latches loaded with all 1s
Digital Feedthrough 0.5 nV-s Feedthrough to DAC output with CS high and
= ±3.5 V, DAC loaded with all 1s
= ±3.5 V, DAC loaded with all 0s
= 10 V, R
REF
= 100 Ω, DAC latch alternately
LOAD
loaded with 0s and 1s
= 10 V, R
= 100 Ω
= 0 V
Analog THD 83 dB V
Digital THD Clock = 1 MHz, V
50 kHz f
20 kHz f
71 dB
77 dB
= 3.5 V p-p, all 1s loaded, f = 1 kHz
= 3.5 V
Output Noise Spectral Density 25 nV/√Hz @ 1 kHz
SFDR Performance (Wide Band) Clock = 10 MHz, V
50 kHz f
20 kHz f
78 dB
74 dB
SFDR Performance (Narrow Band) Clock = 1 MHz, V
50 kHz f
20 kHz f
87 dB
85 dB
= 3.5 V
= 3.5 V
POWER REQUIREMENTS
Supply Current, IDD 0.4 10 µA TA = −40°C to +125°C, logic inputs = 0 V or VDD
0.6 µA TA = 25°C, logic inputs = 0 V or VDD
Power Supply Sensitivity1 0.001 %/% ∆VDD = ±5%
1
Guaranteed by design and characterization; not subject to production test.
Rev. D | Page 4 of 28
Page 5
Data Sheet AD5444/AD5446
S
TIMING CHARACTERISTICS
All input signals are specified with tr = tf = 1 ns (10% to 90% of VDD) and timed from a voltage level of (VIL + VIH)/2. VDD = 2.5 V to 5.5 V,
V
= 10 V, I
REF
Table 2.
Parameter1
f
50 50 MHz max Maximum clock frequency.
SCLK
t1 20 20 ns min SCLK cycle time.
t2 8 8 ns min SCLK high time.
t3 8 8 ns min SCLK low time.
t4 8 8 ns min
t5 5 5 ns min Data setup time.
t6 4.5 4.5 ns min Data hold time.
t7 5 5 ns min
t8 30 30 ns min
t9 23 30 ns min SCLK active edge to SDO valid.
Update Rate 2.7 2.7 MSPS
1
Guaranteed by design and characterization; not subject to production test.
2 = 0 V, temperature range for Y version: −40°C to +125°C; all specifications T
OUT
V
= 4.5 V to
DD
5.5 V
VDD = 2.5 V to
5.5 V Unit Conditions/Comments
falling edge to SCLK active edge setup time.
SYNC
rising edge to SCLK active edge setup time
SYNC
Minimum SYNC
high time.
Consists of cycle time, SYNC
voltage settling time.
t
1
SCLK
t
SYNC
SDIN
t
4
t
8
DB15 DB0
t
6
t
5
2
Figure 2. Standalone Timing Diagram
t
3
t
7
to T
MIN
, unless otherwise noted.
MAX
high time, data setup time and output
4588-002
t
1
SCLK
t
t
4
YNC
t
6
t
5
SDIN
SDO
NOTES
ALTERNATIVELY, DATA CAN BE CLOCKED INTO INPUT SHIF T REGIS TER ON RISI NG EDGE OF SCLK AS
DETERMINED BY CO NTROL BITS. IN THIS CASE, DATA I S CLOCKED OUT OF SDO O N FALLI NG
EDGE OF SCLK. TIMING AS ABOVE, WITH SCLK INVERTED.
DB15 (N) DB0 (N)
2
t
3
DB15
(N + 1)
t
9
DB15 (N)
Figure 3. Daisy-Chain Timing Diagram
Rev. D | Page 5 of 28
DB0
(N + 1)
DB0 (N)
t
7
t
8
04588-003
Page 6
AD5444/AD5446 Data Sheet
REF
OUT
OUT
Extended (Y Version)
I
OL
200µA
TO
OUTPUT
PIN
200µA
I
OH
C
L
20pF
V
OH (MIN)
+V
OL (MAX)
2
04588-004
ABSOLUTE MAXIMUM RATINGS
TA = 25°C, unless otherwise noted. Transient currents of up to
100 mA do not cause SCR latch-up.
Table 3.
Parameter Rating
VDD to GND −0.3 V to +7 V
V
, RFB to GND −12 V to +12 V
I
1, I
2 to GND −0.3 V to +7 V
Logic Inputs and Outputs1 −0.3 V to VDD + 0.3 V
Input Current (All Pins Except Supplies) ±10 mA
Operating Temperature Range −40°C to +125°C
Storage Temperature Range −65°C to +150°C
Junction Temperature 150°C
10-lead MSOP θJA Thermal Impedance 206°C/W
Lead Temperature, Soldering (10 sec) 300°C
IR Reflow, Peak Temperature (<20 sec) 235°C
1
Overvoltages at SCLK,
SYNC
, and SDIN are clamped by internal diodes.
Stresses above those listed under Absolute Maximum Ratings
may cause permanent damage to the device. This is a stress
rating only; functional operation of the device at these or any
other conditions above those indicated in the operational
section of this specification is not implied. Exposure to absolute
maximum rating conditions for extended periods may affect
device reliability.
Only one absolute maximum rating can be applied at any one
time.
Figure 4. Load Circuit for SDO Timing Specifications
ESD CAUTION
Rev. D | Page 6 of 28
Page 7
Data Sheet AD5444/AD5446
04588-005
10
9
8
7
6
1
2
3
4
5
I
OUT
1
I
OUT
2
GND
SCLK
SDIN
R
FB
V
REF
V
DD
SDO
AD5444/
AD5446
TOP VIEW
(Not to Scale)
SYNC
Pin No.
Mnemonic
Description
OUT
OUT
REF
PIN CONFIGURATION AND FUNCTION DESCRIPTIONS
Figure 5. Pin Configuration
Table 4. Pin Function Descriptions
1 I
2 I
1 DAC Current Output.
2 DAC Analog Ground. This pin should normally be tied to the analog ground of the system.
3 GND Ground Pin.
4 SCLK Serial Clock Input. By default, data is clocked into the input shift register on the falling edge of the serial clock
input. Alternatively, by means of the serial control bits, the device can be configured such that data is clocked
into the shift register on the rising edge of SCLK.
5 SDIN Serial Data Input. Data is clocked into the 16-bit input register on the active edge of the serial clock input.
By default on power-up, data is clocked into the shift register on the falling edge of SCLK. The control bits allow
the user to change the active edge to the rising edge.
6
Active Low Control Input. This is the frame synchronization signal for the input data. When
SYNC
is taken low,
SYNC
data is loaded to the shift register on the active edge of the following clocks. The output updates on the rising
edge of
SYNC
.
7 SDO Serial Data Output. This pin allows a number of parts to be daisy-chained. By default, data is clocked into the shift
register on the falling edge and out via SDO on the rising edge of SCLK. Data is always clocked out on the
alternate edge to data loaded to the shift register.
8 VDD Positive Power Supply Input. This part can be operated from a supply of 2.5 V to 5.5 V.
9 V
DAC Reference Voltage Input.
10 RFB DAC Feedback Resistor. Establishes voltage output for the DAC by connecting to an external amplifier output.
Rev. D | Page 7 of 28
Page 8
AD5444/AD5446 Data Sheet
–0.5
–0.4
–0.3
–0.2
–0.1
0
0.1
0.2
0.3
0.4
0.5
0 512 1024 1536 2048 2560 3072 3584 4096
CO
DE
INL (LSB)
TA = 25°C
V
REF
= 10V
V
DD
= 5V
04588-006
2.0
–2.0
–1.6
–1.2
–0.8
–0.4
0
0.4
0.8
1.2
1.6
0 2048 4096 6144 8192 10240 12288 14336 16384
04588-076
CODE
INL (LSB)
T
A
= 25°C
V
REF
= 10V
V
DD
= 5V
–1.0
–0.8
–0.6
–0.4
–0.2
0
0.2
0.4
0.6
0.8
1.0
0 512 1024 1536 2048 2560 3072 3584 4096
CODE
DNL (LSB)
T
A
= 25°C
V
REF
= 10V
V
DD
= 5V
04588-008
2.0
–2.0
–1.6
–1.2
–0.8
–0.4
0
0.4
0.8
1.2
1.6
0 2048 4096 6144 8192 10240 12288 14336 16384
04588-077
CODE
DNL (LSB)
TA = 25°C
V
REF
= 10V
V
DD
= 5V
–1.00
–0.75
–0.50
–0.25
0
0.25
0.50
0.75
1.00
2 3 4 5 6 7 8 9 10
REFERENCE VOLTAGE (V)
INL (L
SB)
TA = 25°C
V
DD
= 5V
AD5444
04588-047
MAX INL
MIN INL
–2.0
–1.5
–1.0
–0.5
0
0.5
1.0
1.5
2.0
2 3 4 5 6 7 8 9 10
REFERENCE VOLTAGE (V)
DNL (LSB)
TA = 25°C
V
DD
= 5V
AD5444
04588-048
MAX DNL
MIN DNL
TYPICAL PERFORMANCE CHARACTERISTICS
Figure 6. INL vs. Code (12-Bit DAC)
Figure 7. INL vs. Code (14-Bit DAC)
Figure 9. DNL vs. Code (14-Bit DAC)
Figure 10. INL vs. Reference Voltage
Figure 8. DNL vs. Code (12-Bit DAC)
Figure 11. DNL vs. Reference Voltage
Rev. D | Page 8 of 28
Page 9
Data Sheet AD5444/AD5446
–1.0
–0.8
–0.6
–0.4
–0.2
0
0.2
0.4
0.6
0.8
1.0
0 512 1024 1536 2048 2560 3072 3584 4096
CODE
TUE (LSB)
T
A
= 25°C
V
REF
= 10V
V
DD
= 5V
04588-013
2.0
–2.0
–1.6
–1.2
–0.8
–0.4
0
0.4
0.8
1.2
1.6
0 2048 4096 6144 8192 10240 12288 14336 16384
04588-078
CODE
INL (LSB)
T
A
= 25°C
V
REF
= 10V
V
DD
= 5V
–2.0
–1.5
–1.0
0
1.0
1.5
2.0
2 3 4 5 8 9 10
R
EFERENCE VOLTAGE (V)
TUE (LSB)
04588-052
76
MAX TUE
–0.5
0.5
TA = 25°C
V
DD
= 5V
AD5444
MIN TUE
–0.3
–0.2
–0.1
0
0.1
0.2
0.3
–60 –40 –20 0 60 80 100 120 140
TEMPERATURE (°C)
GAIN ERROR (LSB)
V
REF
= 10V
04588-049
4020
VDD = 5V
VDD = 3V
–2.0
–1.5
–1.0
0
1.0
1.5
2.0
2 3 4 5 8 9 10
REFERENCE VOLTAGE (V)
GAIN ERROR ( LSB)
04588-051
76
–0.5
0.5
T
A
= 25°C
V
DD
= 5V
AD5444
I
OUT
1, VDD = 3V
I
OUT
1, VDD = 5V
–40 –20 0 20 40 60 80 100 120
TEMPERATURE (°C)
2.0
1.6
1.2
0.8
0.4
0
I
OUT
1 LEAKAGE (nA)
04588-017
Figure 12. TUE vs. Code (12-Bit DAC)
Figure 13. TUE vs. Code (14-Bit DAC)
Figure 15. Gain Error vs. Temperature
Figure 16. Gain Error vs. Reference Voltage
Figure 14. TUE vs. Reference Voltage
Figure 17. I
1 Leakage Current vs. Temperature
OUT
Rev. D | Page 9 of 28
Page 10
AD5444/AD5446 Data Sheet
0 1 2 3 4 5
INPUT VOLTAGE (V)
2.5
2.0
1.5
1.0
0.5
0
SUPPLY CURRENT (mA)
T
A
= 25°C
04588-018
V
DD
= 5V
V
DD
= 3V
ALL 1s
ALL 0s
0.7
0.6
0.5
0.4
0.3
0.2
0.1
0
SUPPLY CURRENT (µA)
–40 –20 0 20 40 60 80 100 120
TEMPERATURE (°C)
VDD = 5V
VDD = 3V
04588-019
04588-055
1 10 100 1k 10k 100k 1M 10M
FREQUENCY (Hz)
6
0
1
2
3
4
5
SUPPLYCURRENT (mA)
T
A
= 25°C
AD5444
LOADING 0101 0101 0101
VDD = 5V
VDD = 3V
2.5 5.5
SUPPLY VOLTAGE (V)
1.8
1.2
1.0
0.4
0.2
0
V
IH
04588-053
1.6
1.4
0.8
0.6
3.0 3.5 4.54.0 5.0
V
IL
THRESHOL D V OLTAGE (V)
TA = 25°C
10
–80
–70
–60
–50
–40
–30
–20
–10
0
10k 100k 1M 10M 100M
GAIN (dB)
FREQUENCY ( Hz )
04588-083
ALL ON
DB11
DB10
DB9
DB8
DB6
DB5
DB4
DB3
DB7
DB2
DB12
DB13
V
DD
= 5V
V
REF
= ±3.5V
C
COMP
= 1.8pF
AD8038 AMPLIF IER
T
A
= 25°C
LOADING
ZS TO FS
0.6
–1.2
–1.0
–0.8
–0.6
–0.4
–0.2
0
0.2
0.4
10k 100k 1M 10M 100M
GAIN (dB)
FREQUENCY ( Hz )
04588-084
T
A
= 25°C
V
DD
= 5V
V
REF
= ±3.5V
C
COMP
= 1.8pF
AD8038 AMPLIF IER
Figure 18. Supply Current vs. Logic Input Voltage
Figure 19. Supply Current vs. Temperature
Figure 21. Threshold Voltage vs. Supply Voltage
Figure 22. Reference Multiplying Bandwidth vs. Frequency and Code
Figure 20. Supply Current vs. Update Rate
Figure 23. Reference Multiplying Bandwidth vs. Frequency—All 1s Loaded
Rev. D | Page 10 of 28
Page 11
Data Sheet AD5444/AD5446
–
–
R
3
TA = 25°C
V
= 5V
DD
0
–3
GAIN(dB)
–6
–9
10k 100k 1M 10M 100M
= ±2V, AD8038 C
V
REF
V
= ±2V, AD8038 C
REF
V
= ±15V, AD8038 C
REF
V
= ±15V, AD8038 C
REF
V
= ±15V, AD8038 C
REF
= 1pF
COMP
= 1.5pF
COMP
= 1pF
COMP
= 1.5pF
COMP
= 1.8pF
COMP
FREQUENCY (Hz)
Figure 24. Reference Multiplying Bandwidth vs. Frequency
and Compensation Capacitor
0.08
0.06
0.04
0.02
0
–0.02
OUTPUT VOLTAGE (V)
–0.04
–0.06
50 200 225 250
Figure 25. Midscale Transition, V
1.66
–1.68
–1.70
–1.72
–1.74
–1.76
OUTPUT VOLTAGE (V)
–1.78
–1.80
50 200 225 250
Figure 26. Midscale Transition, V
VDD =5V
0x7FF TO 0x800
NRG = 2.154nV-s
VDD = 3V
0x7FF TO 0x800
NRG = 1.794nV-s
VDD =5V
0x800 T O 0x7FF
NRG = 0.694nV-s
VDD =5V
0x800 TO 0x7FF
NRG = 0.694nV-s
TIME (ns)
VDD =5V
0x7FF TO 0x800
NRG = 2.154nV-s
VDD = 3V
0x7FF TO 0x800
NRG = 1.794nV-s
VDD =5V
0x800 TO 0x7FF
NRG = 0.694nV-s
VDD =5V
0x800 TO 0x7FF
NRG = 0.694n V-s
TIME (ns)
175100 125 15075
175100 125 15075
TA = 25°C
V
AD8038 AMP
C
= 0 V
REF
TA = 25°C
V
AD8038 AMP
C
= 3.5 V
REF
REF
COMP
REF
COMP
= 0V
= 3.5V
04588-057
= 1.8pF
04588-058
= 1.8pF
04588-059
10
TA = 25°C
= 3V
V
0
DD
AD8038 AMPLIFIER
–10
–20
–30
–40
–50
PSRR (dB)
–60
–70
–80
–90
–100
1 10 100 1k 10k 100k 1M 10M
FULL SCALE
ZERO SCALE
04588-060
FREQUENCY ( Hz )
Figure 27. Power Supply Rejection Ratio vs. Frequency
60
TA = 25°C
= 5V
V
DD
V
=±3.5V
REF
–65
–70
–75
THD+ N (dB)
–80
–85
–90
100 1k 10k 100k
FREQUENCY (Hz)
04588-061
Figure 28. THD + Noise vs. Frequency
100
MCLK = 200kHz
Frequency
OUT
04588-062
= 3.5V
MCLK = 500kHz
20 30 4010
f
OUT
(kHz)
80
MCLK = 1MHz
60
(dB)
SFD
40
20
TA = 25°C
V
REF
AD8038 AMP
0
050
Figure 29. Wideband SFDR vs. f
Rev. D | Page 11 of 28
Page 12
AD5444/AD5446 Data Sheet
–120
–100
–80
–60
–40
–20
0
0 500k
T
A
= 25°C
V
DD
= 5V
V
REF
= 3.5V
AD8038 AMP
FREQUENCY (Hz)
400k300k200k100k
SFDR (dB)
04588-063
–120
–100
–80
–60
–40
–20
0
0 500k
TA = 25°C
V
DD
= 5V
V
REF
= 3.5V
AD8038 AMP
FREQUENCY (Hz)
400k300k200k100k
SFDR (dB)
04588-064
–120
–100
–80
–60
–40
–20
0
10k 30k
T
A
= 25°C
V
DD
= 5V
V
REF
= 3.5V
AD8038 AMP
FREQUENCY (Hz)
25k20k15k
SFDR (dB)
04588-065
–120
–100
–80
–60
–40
–20
0
30k 70k
TA = 25°C
V
DD
= 5V
V
REF
= 3.5V
AD8038 AMP
FREQUENCY (Hz)
60k50k40k
SFDR (dB)
04588-066
Figure 30. Wideband SFDR , f
Figure 31. Wideband SFDR, f
= 20 kHz, Clock = 1 MHz
OUT
= 50 kHz, Clock = 1 MHz
OUT
Figure 32. Narrow-Band SFDR, f
Figure 33. Narrow-Band SFDR, f
= 20 kHz, Clock = 1 MHz
OUT
= 50 kHz, Clock = 1 MHz
OUT
Rev. D | Page 12 of 28
Page 13
Data Sheet AD5444/AD5446
–100
–90
–80
–60
–40
–20
0
10k 35k
T
A
= 25°C
V
REF
= 3.5V
AD8038 AMP
FREQUENCY (Hz)
30k25k20k15k
IMD (dB)
04588-067
–70
–50
–30
–10
–100
–90
–80
–60
–40
–20
0
0 500k
T
A
= 25°C
V
REF
= 3.5V
AD8038 AMP
FREQUENCY (Hz)
400k300k200k100k
IMD (dB)
04588-068
–70
–50
–30
–10
04588-069
100 1k 10k 100k 1M
FREQUENCY (Hz)
80
0
70
OUTPUT NOISE (nV/ Hz)
T
A
= 25°C
AD8038 AMP
50
60
40
20
30
10
FULL SCALE
LOADED TO DAC
MIDSCALE
LOADED TO DAC
ZERO SCAL E
LOADED TO DAC
Figure 34. Narrow-Band IMD, f
Figure 35. Wideband IMD, f
= 20 kHz and 25 kHz, Clock = 1 MHz
OUT
= 20 kHz and 25 kHz, Clock = 1 MHz
OUT
Figure 36. Output Noise Spectral Density
Rev. D | Page 13 of 28
Page 14
AD5444/AD5446 Data Sheet
1
54
32
V
VVVV
THD
2222
log20
+++
=
TERMINOLOGY
Relative Accuracy or Integral Nonlinearity
Relative accuracy or integral nonlinearity is a measure of the
maximum deviation from a straight line passing through the
endpoints of the DAC transfer function. It is measured after
adjusting for zero scale and full scale and is normally expressed
in LSBs or as a percentage of full-scale reading.
Differential Nonlinearity
Differential nonlinearity is the difference between the measured
change and the ideal 1 LSB change between any two adjacent
codes. A specified differential nonlinearity of −1 LSB maximum
over the operating temperature range ensures monotonicity.
Gain Error
Gain error or full-scale error is a measure of the output error
between an ideal DAC and the actual device output. For this
DAC, ideal maximum output is V
− 1 LSB. Gain error of the
REF
DAC is adjustable to zero with external resistance.
Output Leakage Current
Output leakage current is current that flows in the DAC ladder
switches when the ladder is turned off. For the I
1 line, it can
OUT
be measured by loading all 0s to the DAC and measuring the
I
1 current. Minimum current flows in the I
OUT
2 line when
OUT
the DAC is loaded with all 1s.
Output Capacitance
Capacitance from I
OUT
1 or I
2 to AGND.
OUT
Output Current Settling Time
The amount of time it takes for the output to settle to a specified level for a full-scale input change. For this device, it is
specified with a 100 Ω resistor to ground. The settling time
specification includes the digital delay from the
SYNC
rising
edge to the full-scale output change.
Digital-to-Analog Glitch Impulse
The amount of charge injected from the digital inputs to the
analog output when the inputs change state. This is normally
specified as the area of the glitch in either picoamps per second
or nanovolts per second, depending upon whether the glitch is
measured as a current or voltage signal.
Digital Feedthrough
When the device is not selected, high frequency logic activity on the device’s digital inputs can be capacitively coupled
through the device to show up as noise on the I
OUT
1 and I
OUT
2
pins and, subsequently, into the following circuitry. This noise is
digital feedthrough.
Multiplying Feedthrough Error
Multiplying feedthrough error is due to capacitive feedthrough
from the DAC reference input to the DAC I
1 line, when all
OUT
0s are loaded to the DAC.
Total Harmonic Distortion (THD)
The DAC is driven by an ac reference. The ratio of the rms sum
of the harmonics of the DAC output to the fundamental value is
the THD. Usually only the lower-order harmonics, such as second
to fifth, are included.
Digital Intermodulation Distortion
Second-order intermodulation (IMD) measurements are the
relative magnitudes of the fa and fb tones digitally generated by
the DAC and the second-order products at 2fa − fb and 2fb − fa.
Compliance Voltage Range
The maximum range of (output) terminal voltage for which
the device provides the specified characteristics.
Spurious-Free Dynamic Range (SFDR)
The usable dynamic range of a DAC before spurious noise
interferes or distorts the fundamental signal. SFDR is the
measure of difference in amplitude between the fundamental
and the largest harmonically or nonharmonically related spur
from dc to full Nyquist bandwidth (half the DAC sampling
rate or f
/2). Narrow-band SFDR is a measure of SFDR over
S
an arbitrary window size, in this case 50% of the fundamental.
Digital SFDR is a measure of the usable dynamic range of the
DAC when the signal is a digitally generated sine wave.
Rev. D | Page 14 of 28
Page 15
Data Sheet AD5444/AD5446
V
V
GENERAL DESCRIPTION
DAC SECTION
The AD5444/AD5446 are 12-bit and 14-bit current output
DACs consisting of segmented (4 bits), inverting R– 2R ladder
configurations. A simplified diagram for the 12-bit AD5444
is shown in Figure 37.
REF
The feedback resistor (RFB) has a value of R. The value of R is
typically 9 kΩ (7 kΩ minimum, 11 kΩ maximum). If I
kept at the same potential as GND, a constant current flows in
each ladder leg, regardless of digital input code. Therefore, the
input resistance presented at V
nally of value R. The DAC output (I
producing various resistances and capacitances. The external
amplifier choice should take into account the variation in
impedance generated by the DAC on the amplifiers inverting
input node.
Access is provided to the V
the DAC, making the device extremely versatile and allowing it
to be configured in several different operating modes. For
example, the device provides unipolar output mode, 4-quadrant
multiplication in bipolar mode, and single-supply mode of
operation. Note that a matching switch is used in series with the
internal R
when measuring R
RR R
2R
2R
S1
DAC DATA LATCHES
2R
S2
S3
AND DRIVERS
2R
S12
2R
R
R
FB
I
1
OUT
I
2
OUT
Figure 37. Simplified Ladder
1 is
OUT
is always constant and nomi-
REF
1) is code-dependent,
OUT
, RFB, and both I
REF
. Power must be applied to VDD to achieve continuity
FB
.
FB
terminals of
OUT
DD
4464-029
CIRCUIT OPERATION
Unipolar Mode
Using a single op amp, the AD5444/AD5446 can easily be
configured to provide 2-quadrant multiplying operation or
a unipolar output voltage swing, as shown in Figure 38.
When an output amplifier is connected in unipolar mode, the
output voltage is given by
V
OUT
D
n
2
where:
D is the fractional representation of the digital word loaded to
the DAC:
D = 0 to 4095 (12-bit AD5444)
D = 0 to 16383 (14-bit AD5446)
n is the number of bits.
Note that the output voltage polarity is opposite to the V
polarity for dc reference voltages.
This DAC is designed to operate with either negative or positive
reference voltages. The V
digital logic only to drive the on and off states of the DAC
switches. The DAC is also designed to accommodate ac reference input signals in the range of −10 V to +10 V. With a xed
+10 V reference, the circuit shown in Figure 38 provides a
unipolar 0 V to −10 V output voltage swing. When V
ac signal, the circuit performs 2-quadrant multiplication.
Table 5 shows the relationship between digital code and
expected output voltage for unipolar operation.
Table 5. Unipolar Code
Digital Input Analog Output (V)
1111 1111 1111 −V
1000 0000 0000 −V
0000 0000 0001 −V
0000 0000 0000 −V
R2
V
REF
power pin is used by the internal
DD
(4095/4096)
REF
(2048/4096) = −V
REF
(1/4096)
REF
(0/4096) = 0
REF
REF
/2
is an
IN
REF
V
V
REF
R1
NOTES
1. R1 AND R2 USED ONLY IF GAI N ADJUSTMENT IS REQUIRED.
2. C1 PHASE COMPENSATION (1pF TO 2pF) MAY BE REQUIRED,
IF A1 IS A HIGH SPEEDAMPLIFIER.
AD5444/
V
REF
AD5446
SCLKSYNC
MICROCONTRO LLER
DD
SDIN
R
FB
I
OUT
I
OUT
C1
1
2
AGND
A1
V
= 0V TO –V
OUT
REF
04588-030
Figure 38. Unipolar Operation
Rev. D | Page 15 of 28
Page 16
AD5444/AD5446 Data Sheet
2
REF
0000 0000 0001
−V
REF
(2047/2048)
REF
04588-031
I
OUT
1
I
OUT
2
AD5444/
AD5446
V
REF
V
DD
C1
A1
V
OUT
= –V
REF
TO +V
REF
AGND
R2
V
DD
V
REF
±10V
SDIN
SCLKSYNC
MICROCONTROLLER
A2
R4
10kΩ
R5
20kΩ
NOTES
1. R1 AND R2 USED ONLY IF GAINADJUSTME NT IS REQUIRED.
ADJUST R1 FOR V
OUT
= 0V WITH CODE 10000000 LOADED TO DAC.
2. MATCHING AND TRACKING IS ESSENTIAL FOR RESISTOR PAIRS
3. C1 PHASE COM P E NSATION (1pF TO 2pF) MAY BE REQUIRED,
IFA1/A2 IS A HIGH SPEED AMPLIFIER.
R3 AND R4.
R3
20kΩ
R1
R
FB
Bipolar Operation
In some applications, it may be necessary to generate a full
4-quadrant multiplying operation, or a bipolar output swing.
This can easily be accomplished by using another external
amplifier and some external resistors, as shown in Figure 39.
In this circuit, the second amplifier (A2) provides a gain of 2.
Biasing the external amplifier with an offset from the reference
voltage results in a full 4-quadrant multiplying operation. The
transfer function of this circuit shows that both negative and
positive output voltages are created as the input data (D) is
incremented from code zero (V
(V
− 0 V) to full scale (V
OUT
D
OUT
VV −
REF
×=
−1
n
OUT
V
OUT
= +V
REF
= −V
REF
) to midscale
REF
)
where:
D is the fractional representation of the digital word loaded
to the DAC:
D = 0 to 4095 (12-bit AD5444)
D = 0 to 16383 (14-bit AD5446)
n is the resolution of the DAC.
When V
is an ac signal, the circuit performs 4-quadrant
IN
multiplication.
Table 6 shows the relationship between digital code and the
expected output voltage for bipolar operation.
Table 6. Bipolar Code
Digital Input Analog Output (V)
1111 1111 1111 +V
(2047/2048)
1000 0000 0000 0
0000 0000 0000 −V
(0/2048)
Stability
In the current-to-voltage (I-to-V) configuration, the I
OUT
1of the
DAC and the inverting node of the op amp must be connected
as closely as possible, and proper PCB layout techniques must
be employed. Because every code change corresponds to a step
function, gain peaking can occur if the op amp has limited GBP
and excessive parasitic capacitance exists at the inverting node.
This parasitic capacitance introduces a pole into the open-loop
response that can cause ringing or instability in the closed-loop
applications circuit.
An optional compensation capacitor (C1) can be added in
parallel with R
for stability, as shown in Figure 38 and
FB
Figure 39. Too small a value for C1 can produce ringing at
the output, while too large a value can adversely affect the
settling time. C1 should be found empirically, but 1 pF to
2 pF is generally adequate for the compensation.
Figure 39. Bipolar Operation (4-Quadrant Multiplication)
Rev. D | Page 16 of 28
Page 17
Data Sheet AD5444/AD5446
04588-032
NOTES
1. ADDITI ONAL PINS OMITTED FOR CLARITY.
2. C1 PHASE COM P E NSATION (1pF TO 2pF) MAY BE REQUIRED,
IFA1 IS A HIGH SPEED AMPLIFIER.
I
OUT
1
GND
V
OUT
R2
V
IN
R
FB
V
DD
V
REF
R1
V
DD
V
DD
R
FB
I
OUT
1
I
OUT
2
C1
V
OUT
= 0V TO +2.5V
GND
V
DD
= +5V
V
REF
NOTES
1. ADDITIONAL PINS OMITTED FOR CLARITY.
2. C1 PHASE COM P E NSATION (1pF TO 2pF) MAY BE REQUIRED,
IFA1 IS A HIGH SPEED AMPLIFIER.
ADR03
V
OUTVIN
GND
–5V
+5V
–2.5V
04588-033
NOTES
1. ADDITIONAL PINS OMITTED FOR CLARITY.
2. C1 PHASE COMPENSATION (1pFTO 2pF) MAY BE REQUIRED,
IFA1 IS A HIGH SPEED AMPLIFIER.
V
DD
R
FB
I
OUT
1
I
OUT
2
C1
V
OUT
GND
V
DD
V
REF
04588-034
GAIN =
R1 =
R2 + R3
R2
R2R3
R2 + R3
R1
V
IN
R3
R2
SINGLE-SUPPLY APPLICATIONS
Voltage Switching Mode of Operation
Figure 40 shows the AD5444/AD5446 DACs operating in the
voltage switching mode. The reference voltage (V
to the I
voltage is available at the V
a positive reference voltage results in a positive output voltage,
making single-supply operation possible. The output from
the DAC is voltage at a constant impedance (the DAC ladder
resistance). Therefore, an op amp is necessary to buffer the
output voltage. The reference input no longer sees a constant
input impedance but rather one that varies with code, so the
voltage input should be driven from a low impedance source.
It is important to note that, with this configuration, VIN is limited to low voltages, because the switches in the DAC ladder do
not have the same source-drain drive voltage. As a result, their
on resistance differs, which degrades the integral linearity of the
DAC. In addition, V
or an internal diode turns on, exceeding the maximum ratings
of the device. In this type of application, the full range of the
multiplying capability of the DAC is lost.
Positive Output Voltage
The output voltage polarity is opposite to the V
dc reference voltages. To achieve a positive voltage output, an
applied negative reference to the input of the DAC is preferred
over the output inversion through an inverting amplifier because
of the resistor’s tolerance errors. To generate a negative reference,
the reference can be level-shifted by an op amp such that the
V
OUT
and −2.5 V, respectively, as shown in Figure 41.
OUT
1 pin, I
2 is connected to AGND, and the output
OUT
terminal. In this configuration,
REF
Figure 40. Single-Supply Voltage Switching Mode Operation
must not go negative by more than 0.3 V,
IN
and GND pins of the reference become the virtual ground
) is applied
IN
polarity for
REF
ADDING GAIN
In applications in which the output voltage is required to be
greater than V
amplifier, or it can be achieved in a single stage. It is important
to take into consideration the effect of the temperature coefficients of the DAC’s thin film resistors. Simply placing a resistor
in series with the R
temperature coefficients and result in larger gain temperature
coefficient errors. Instead, increase the gain of the circuit by
using the recommended configuration shown in Figure 42.
R1, R2, and R3 should all have similar temperature coefficients,
but they need not match the temperature coefficients of the
DAC. This approach is recommended in circuits where gains
of greater than 1 are required.
DIVIDER OR PROGRAMMABLE GAIN ELEMENT
Current-steering DACs are very flexible and lend themselves to
many different applications. If this type of DAC is connected as
the feedback element of an op amp and R
resistor, as shown in Figure 43, then the output voltage is
inversely proportional to the digital input fraction, D.
For D = 1 − 2
Rev. D | Page 17 of 28
Figure 41. Positive Voltage Output with Minimum Components
, gain can be added with an additional external
IN
resistor can cause mismatches in the
FB
Figure 42. Increasing Gain of Current Output DAC
is used as the input
FB
−n
, the output voltage is
V
= −VIN/D = −VIN/(1 − 2−n)
OUT
Page 18
AD5444/AD5446 Data Sheet
04588-035
NOTES:
1. ADDITI ONAL PINS OMITTED FOR CLARITY.
I
OUT
1
GND
V
OUT
V
IN
R
FB
V
DD
V
REF
V
DD
The input bias current of an op amp also generates an offset
at the voltage output as a result of the bias current flowing
in the feedback resistor, R
currents low enough to prevent any significant errors in
12-bit applications.
Common-mode rejection of the op amp is important in voltage
switching circuits because it produces a code-dependent error
at the voltage output of the circuit. Most op amps have adequate
common-mode rejection for use at 8-bit, 10-bit, and 12-bit
resolutions.
Figure 43. Current-Steering DAC Used as a Divider
or Programmable Gain Element
As D is reduced, the output voltage increases. For small values
of the digital fraction (D), it is important to ensure that the
amplifier does not saturate and the required accuracy is met.
For example, an 8-bit DAC driven with the binary code 0x10
(0001 0000), that is, 16 decimal, in the circuit of Figure 43,
should cause the output voltage to be 16 × V
. However, if the
IN
DAC has a linearity specification of ±0.5 LSB, then D can, in
fact, have a weight in the range of 15.5/256 to 16.5/256, so the
possible output voltage is in the range 15.5 V
to 16.5 VIN. This
IN
is an error of 3%, even though the DAC itself has a maximum
error of 0.2%.
DAC leakage current is also a potential error source in divider
circuits. The leakage current must be counterbalanced by an
opposite current supplied from the op amp through the DAC.
Because only a fraction (D) of the current into the V
is routed to the I
1 terminal, the output voltage has to change,
OUT
terminal
REF
as follows:
Output Error Voltage due to DAC Leakage = (Leakage × R)/D
where R is the DAC resistance at the V
terminal.
REF
For a DAC leakage current of 10 nA, R equal to 10 kΩ, and a gain
(1/D) of 16, the error voltage is 1.6 mV.
AMPLIFIER SELECTION
The primary requirement for the current-steering mode is
an amplifier with low input bias currents and low input offset
voltage. The input offset voltage of an op amp is multiplied by
the variable gain (due to the code-dependent output resistance
of the DAC) of the circuit. A change in this noise gain between
two adjacent digital fractions produces a step change in the
Provided that the DAC switches are driven from true wideband
low impedance sources (V
Consequently, the slew rate and settling time of a voltage switching
DAC circuit is determined largely by the output op amp. To
obtain minimum settling time in this configuration, it is important to minimize capacitance at the V
node in this application) of the DAC. This is done by using low
input, capacitance buffer amplifiers and careful board design.
Most single-supply circuits include ground as part of the analog
signal range, which, in turn, requires an amplifier that can handle
rail-to-rail signals. A large range of single-supply amplifiers is
available from Analog Devices, Inc. (see Tabl e 8 and Table 9 for
suitable suggestions).
REFERENCE SELECTION
When selecting a reference for use with the AD5444/AD5446
current output DAC, pay attention to the output voltage temperature coefficient specification. This parameter affects not
only the full-scale error but can also affect the linearity (INL
and DNL) performance. The reference temperature coefficient
should be consistent with the system accuracy specifications.
For example, an 8-bit system required to hold its overall specification to within 1 LSB over the temperature range 0°C to 50°C
dictates that the maximum system drift with temperature
should be less than 78 ppm/°C.
A 12-bit system with the same temperature range to overall
specification within 2 LSBs requires a maximum drift of
10 ppm/°C. By choosing a precision reference with low output
temperature coefficient, this error source can be minimized.
Table 7 suggests some of the dc references available from
Analog Devices that are suitable for use with this range of
current output DACs.
output voltage due to the amplifier’s input offset voltage. This
output voltage change is superimposed upon the desired change
in output between the two codes and gives rise to a differential
linearity error, which, if large enough, can cause the DAC to be
nonmonotonic.
. Most op amps have input bias
FB
and AGND), they settle quickly.
IN
node (voltage output
REF
Rev. D | Page 18 of 28
Page 19
Data Sheet AD5444/AD5446
Part No.
Supply Voltage (V)
VOS (Max) (µV)
IB (Max) (nA)
0.1 Hz to 10 Hz Noise (µV p-p)
Supply Current (µA)
Package
AD8065
5 to 24
145
180
1500
0.006
SOIC-8, SOT-23, MSOP
Table 7. Suitable Analog Devices Precision References
Initial Tolerance
Part No. Output Voltage (V)
ADR01 10 0.05 3 1 20 SOIC-8
ADR01 10 0.05 9 1 20 TSOT-23, SC70
ADR02 5 0.06 3 1 10 SOIC-8
ADR02 5 0.06 9 1 10 TSOT-23, SC70
ADR03 2.5 0.10 3 1 6 SOIC-8
ADR03 2.5 0.10 9 1 6 TSOT-23, SC70
ADR06 3 0.10 3 1 10 SOIC-8
ADR06 3 0.10 9 1 10 TSOT-23, SC70
ADR431 2.5 0.04 3 0.8 3.5 SOIC-8
ADR435 5 0.04 3 0.8 8 SOIC-8
ADR391 2.5 0.16 9 0.12 5 TSOT-23
ADR395 5 0.10 9 0.12 8 TSOT-23
Accuracy (%)
Table 8. Suitable Analog Devices Precision Op Amps
OP97 ±2 to ±20 25 0.1 0.5 600 SOIC-8
OP1177 ±2.5 to ±15 60 2 0.4 500 MSOP, SOIC-8
AD8551 2.7 to 5 5 0.05 1 975 MSOP, SOIC-8
AD8603 1.8 to 6 50 0.001 2.3 50 TSOT
AD8628 2.7 to 6 5 0.1 0.5 850 TSOT, SOIC-8
Temperature Drift
Coefficient (ppm/°C) ISS (mA) Output Noise (µV p-p) Package
Table 9. Suitable Analog Devices High Speed Op Amps
BW @ ACL
Part No. Supply Voltage (V)
AD8021 ±2.25 to ±12 490 120 1000 10500 SOIC-8, MSOP
AD8038 3 to 12 350 425 3000 750 SOIC-8, SC70-5
AD9631 ±3 to ±6 320 1300 10,000 7000 SOIC-8
(Typ) (MHz)
Slew Rate
(Typ) (V/µs) VOS (Max) (µV) IB (Max) (nA) Package
Rev. D | Page 19 of 28
Page 20
AD5444/AD5446 Data Sheet
C1
C0
Function Implemented
04588-037
DB0 (LSB)
DB15 (MSB)
DB7 DB6 DB5 DB4
DB3 DB2
DB0
DB1
C1 C0
DB11 DB10
DB8
DB9
X
X
CONTROL BITS
DATA BITS
04588-038
DB0 (LSB)
DB15 (MSB)
DB9 DB8 DB7 DB6
DB5 DB4
DB2
DB3
C1 C0
DB13 DB12
DB10
DB11
DB0
DB1
CONTROL BITS
DATA BITS
SERIAL INTERFACE
The AD5444/AD5446 have an easy-to-use, 3-wire interface that
is compatible with SPI, QSPI, MICROWIRE, and DSP interface standards. Data is written to the device in 16-bit words.
This 16-bit word consists of two control bits, 12 data bits or
14 data bits, as shown in Figure 44 and Figure 45. The AD5446
uses all 14 bits of DAC data while AD5444 uses 12 bits and
ignores the 2 LSBs.
Control Bit C1 and Control Bit C0 allow the user to load and
update the new DAC code and to change the active clock edge.
By default, the shift register clocks data on the falling edge, but
this can be changed via the control bits. If changed, the DAC
core is inoperative until the next data frame. A power cycle
resets this back to the default condition. On-chip, power-on
reset circuitry ensures the device powers on with zero scale
loaded to the DAC register and the I
OUT
line.
Table 10. DAC Control Bits
0 0 Load and update (power-on default)
0 1 Disable SDO
1 0 No operation
1 1 Clock data to shift register on rising edge
SYNC
Function
SYNC
is an edge-triggered input that acts as a frame synchronization signal. Data can be transferred into the device only while
SYNC
is low. To start the serial data transfer,
taken low, observing the minimum
falling edge setup time, t
. To minimize the power consumption
4
SYNC
SYNC
should be
falling to the SCLK
of the device, the interface powers up fully only when the device
is being written to, that is, on the falling edge of
SYNC
.
The SCLK and DIN input buffers are powered down on the
rising edge of
SYNC
.
After the falling edge of the 16th SCLK pulse, bring
to transfer data from the input shift register to the DAC register.
Daisy-Chain Mode
Daisy-chain mode is the default power-on mode. To disable
the daisy-chain function, write 01 to the control word. In daisychain mode, the internal gating on the SCLK is disabled. The
SCLK is continuously applied to the input shift register when
SYNC
is low. If more than 16 clock pulses are applied, the data
ripples out of the shift register and appears on the SDO line.
This data is clocked out on the rising edge of the SCLK (this
is the default; use the control word to change the active edge)
and is valid for the next device on the falling edge (default).
By connecting this line to the SDIN input on the next device in
the chain, a multidevice interface is constructed. Sixteen clock
pulses are required for each device in the system. Therefore, the
total number of clock cycles must equal 16 N, where N is the
number of devices in the chain.
When the serial transfer to all devices is complete,
should be taken high. This prevents any further data from
being clocked into the shift register. A burst clock containing
the exact number of clock cycles can be used, and
taken high some time later. After the rising edge of
is automatically transferred from each device’s input register to
the addressed DAC.
When the control bits = 10, the device is in no operation mode.
This can be useful in daisy-chain applications where the user
does not want to change the settings of a particular DAC in the
chain. Simply write 10 to the control bits for that DAC and the
following data bits are ignored.
SYNC
SYNC
SYNC
SYNC
high
can be
, data
Figure 44. AD5444 12-Bit Input Shift Register Contents
Figure 45. AD5446 14-Bit Input Shift Register Contents
Rev. D | Page 20 of 28
Page 21
Data Sheet AD5444/AD5446
SCLK
SCK
SYNC
SPIxSEL
SDIN
MO
SI
ADSP-2191*
*ADDITIONAL PINS OMITTED FOR CLARITY.
AD5444/
AD5446*
04588-074
SCLK
SCLK
SYNC
TFS
SDIN
DT
ADSP-2101/
ADSP-2103/
ADSP-2191*
*ADDITIONAL PINS OMITTED FOR CLARITY.
04588-082
AD5444/AD5446*
SCLK
SCK
SYNC
SPIxSEL
SDIN
MOSI
ADSP-BF5xx*
*ADDITIONAL PINS OMITTED FOR CLARITY
AD5444/AD5446*
04588-039
SCLK
SCLK
SYNC
TFS
SDIN
DT
ADSP-BF5xx*
*ADDITIONAL PINS OMITTED FOR CLARITY
04588-040
AD5444/AD5446*
MICROPROCESSOR INTERFACING
Microprocessor interfacing to the AD5444/AD5446 DAC is
through a serial bus that uses standard protocol compatible
with microcontrollers and DSP processors. The communications channel is a 3-wire interface consisting of a clock signal, a
data signal, and a synchronization signal. The AD5444/AD5446
requires a 16-bit word, with the default being data valid on the
falling edge of SCLK, but this can be changed using the control
bits in the data-word.
ADSP-21xx to AD5444/AD5446 Interface
The ADSP-21xx family of DSPs is easily interfaced to the
AD5444/AD5446 DAC without the need for extra glue logic.
Figure 46 is an example of an SPI interface between the DAC
and the ADSP-2191M. SCK of the DSP drives the serial clock
SPIxSEL
SYNC
is driven from one of the port lines, in this
.
line, SCLK.
case
Table 11. SPORT Control Register Setup
Name Setting Description
TFSW 1 Alternate framing
INVTFS 1 Active low frame signal
DTYPE 00 Right-justify data
ISCLK 1 Internal serial clock
TFSR 1 Frame every word
ITFS 1 Internal framing signal
SLEN 1111 16-bit data-word
ADSP-BF5xx to AD5444/AD5446 Interface
The ADSP-BF5xx family of processors has an SPI-compatible
port that enables the processor to communicate with SPIcompatible devices. A serial interface between the ADSP-BF5xx
and the AD5444/AD5446 DAC is shown in Figure 48. In this
configuration, data is transferred through the MOSI (master
output/slave input) pin.
SYNC
is driven by the SPI chip select
pin, which is a reconfigured programmable flag pin.
Figure 46. ADSP-2191M SPI to AD5444/AD5446 Interface
A serial interface between the DAC and DSP SPORT is shown
in Figure 47. In this interface example, SPORT0 is used to transfer data to the DAC shift register. Transmission is initiated by
writing a word to the Tx register after the SPORT has been
enabled. In a write sequence, data is clocked out on each rising
edge of the DSP serial clock and clocked into the DAC input
shift register on the falling edge of its SCLK. The update of the
DAC output takes place on the rising edge of the
Figure 47. ADSP-2101/ADSP-2103/ADSP-2191 SPORT to
AD5444/AD5446 Interface
SYNC
signal.
Communication between two devices at a given clock speed
is possible when the following specifications are compatible:
frame sync delay and frame sync setup-and-hold, data delay
and data setup-and-hold, and SCLK width. The DAC interface expects a t
SYNC
(
4
falling edge to SCLK falling edge setup
time) of 13 ns minimum. See the ADSP-21xx User Manual for
information on clock and frame sync frequencies for the
SPORT register.
Table 11 shows the setup for the SPORT control register.
The ADSP-BF5xx processor incorporates channel synchronous
serial ports (SPORT). A serial interface between the DAC and
the DSP SPORT is shown in Figure 49. When the SPORT is
enabled, initiate transmission by writing a word to the Tx registe r.
The data is clocked out on each rising edge of the DSPs serial
clock and clocked into the DAC input shift register on the
falling edge of its SCLK. The DAC output is updated by using
the transmit frame synchronization (TFS) line to provide a
SYNC
Rev. D | Page 21 of 28
Figure 48. ADSP-BF5xx to AD5444/AD5446 Interface
signal.
Figure 49. ADSP-BF5xx to AD5444/AD5446 Interface
Page 22
AD5444/AD5446 Data Sheet
SCLK
TxD
8051*
SYNC
P1.1
SDIN
RxD
*ADDITIONAL PINS OMITTED FOR CLARITY
04588-041
AD5444/AD5446*
SCLK
SCK
AD5444/AD5446*
SYNC
PC7
SDIN
MOSI
MC68HC11*
*ADDITIONAL PINS OMITTED FOR CLARITY
04588-042
SCLK
SK
MICROWIRE*
SYNC
CS
SDIN
SO
*ADDITIONAL PINS OMITTED FOR CLARITY
04588-043
AD5444/AD5446*
SCLK
SCK/RC3
PIC16C6x/7x*
SYNC
RA1
SDIN
SDI/RC4
*ADDITIONAL PINS OMITTED FOR CLARITY
04588-044
AD5444/AD5446*
80C51/80L51 to AD5444/AD5446 Interface
A serial interface between the DAC and the 80C51/80L51 is
shown in Figure 50. TxD of the 80C51/80L51 drives SCLK of
the DAC serial interface, while RxD drives the serial data line,
SDIN. P1.1 is a bit-programmable pin on the serial port and
is used to drive
switch, P1.1 is taken low. The 80C51/80L51 transmits data only
in 8-bit bytes; therefore, only eight falling clock edges occur in
the transmit cycle. To load data correctly to the DAC, P1.1 is
left low after the first eight bits are transmitted, and a second
write cycle is initiated to transmit the second byte of data.
Data on RxD is clocked out of the microcontroller on the rising
edge of TxD and is valid on the falling edge. As a result, no glue
logic is required between the DAC and microcontroller interface. P1.1 is taken high following the completion of this cycle.
The 80C51/80L51 provides the LSB of its SBUF register as the
first bit in the data stream. The DAC input register requires its
data with the MSB as the first bit received. The transmit routine
should take this into account.
SYNC
. When data is to be transmitted to the
Figure 51. MC68HC11 to AD5444/AD5446 Interface
If the user wants to verify the data previously written to the
input shift register, the SDO line can be connected to MISO of
SYNC
the MC68HC11, and, with
low, the shift register clocks
data out on the rising edges of SCLK.
MICROWIRE to AD5444/AD5446 Interface
Figure 52 shows an interface between the DAC and any
MICROWIRE-compatible device. Serial data is shifted out
on the falling edge of the serial clock, SK, and is clocked into
the DAC input shift register on the rising edge of SK, which
corresponds to the falling edge of the DAC SCLK.
Figure 50. 80C51/80L51 to AD5444/AD5446 Interface
MC68HC11 Interface to AD5444/AD5446 Interface
Figure 51 is an example of a serial interface between the DAC
and the MC68HC11 microcontroller. The serial peripheral
interface (SPI) on the MC68HC11 is configured for master
mode (MSTR) = 1, clock polarity bit (CPOL) = 0, and the clock
phase bit (CPHA) = 1. The SPI is configured by writing to the
SPI control register (SPCR); see the 68HC11 User Manual. SCK
of the 68HC11 drives the SCLK of the DAC interface, the MOSI
output drives the serial data line (SDIN) of the AD5444/AD5446.
SYNC
The
is being transmitted to the AD5444/AD5446, the
signal is derived from a port line (PC7). When data
SYNC
line is
taken low (PC7). Data appearing on the MOSI output is valid
on the falling edge of SCK. Serial data from the 68HC11 is
transmitted in 8-bit bytes with only eight falling clock edges
occurring in the transmit cycle. Data is transmitted MSB first.
To load data to the DAC, PC7 is left low after the first eight bits
are transferred, and a second serial write operation is performed
to the DAC. PC7 is taken high at the end of this procedure.
Figure 52. MICROWIRE to AD5444/AD5446 Interface
PIC16C6x/7x to AD5444/AD5446 Interface
The PIC16C6x/7x synchronous serial port (SSP) is configured
as an SPI master with the clock polarity bit (CKP) = 0. This is
done by writing to the synchronous serial port control register
(SSPCON); see the PIC16/17 Microcontroller User Manual.
In this example, I/O port RA1 is used to provide a
SYNC
signal and enable the serial port of the DAC. This microcontroller transfers only eight bits of data during each serial
transfer operation; therefore, two consecutive write operations
are required. Figure 53 shows the connection diagram.
Figure 53. PIC16C6x/7x to AD5444/AD5446 Interface
Rev. D | Page 22 of 28
Page 23
Data Sheet AD5444/AD5446
PCB LAYOUT AND POWER SUPPLY DECOUPLING
In any circuit where accuracy is important, careful consideration of the power supply and ground return layout helps to
ensure the rated performance. The printed circuit boards on
which the AD5444/AD5446 are mounted should be designed
so the analog and digital sections are separated and confined to
certain areas of the board. If the DACs are in systems in which
multiple devices require a AGND-to-DGND connection, the
connection should be made at one point only. The star ground
point should be established as close as possible to the devices.
The DAC should have ample supply bypassing of 10 µF in
parallel with 0.1 µF on the supply located as close to the package as possible, ideally right up against the device. The 0.1 µF
capacitor should have low effective series resistance (ESR)
and effective series inductance (ESI), like the common ceramic
types that provide a low impedance path to ground at high
frequencies, to handle transient currents due to internal logic
switching. Low ESR, 1 µF to 10 µF tantalum or electrolytic
capacitors should also be applied at the supplies to minimize
transient disturbance and filter out low frequency ripple.
Fast switching signals such as clocks should be shielded with
digital ground to avoid radiating noise to other parts of the
board, and should never be run near the reference inputs.
Avoid crossover of digital and analog signals. Traces on opposite sides of the board should run at right angles to each other.
This reduces the effects of feedthrough throughout the board.
A microstrip technique, by far the best, is not always possible
with a double-sided board. In this technique, the component
side of the board is dedicated to the ground plane, while signal
traces are placed on the solder side.
It is good practice to employ compact, minimum lead-length
PCB layout design. Leads to the input should be as short as
possible to minimize IR drops and stray inductance.
The PCB metal traces between V
matched to minimize gain error. To maximize high frequency
performance, the I-to-V amplifier should be located as close
to the device as possible.
and RFB should also be
REF
Rev. D | Page 23 of 28
Page 24
AD5444/AD5446 Data Sheet
AD5426
8 1 ±0.25
Serial
RM-10
10 MHz BW, 50 MHz serial
AD5439
10 2 ±0.5
Serial
RU-16
10 MHz BW, 50 MHz serial
AD5446
14 1 ±1
Serial
RM-10
12 MHz BW, 50 MHz serial
AD5543
16 1 ±2
Serial
RM-8
4 MHz BW, 50 MHz serial clock
OVERVIEW OF AD54xx AND AD55xx CURRENT OUTPUT DEVICES
Table 12.
Part Number Resolution (Bits) Number of DACs INL (LSB) Interface Package1 Features
AD5424 8 1 ±0.25 Parallel RU-16, CP-20 10 MHz BW, 17 ns CS pulse width
AD5428 8 2 ±0.25 Parallel RU-20 10 MHz BW, 17 ns CS pulse width
AD5429 8 2 ±0.25 Serial RU-10 10 MHz BW, 50 MHz serial
AD5450 8 1 ±0.25 Serial UJ-8 12 MHz BW, 50 MHz serial
AD5432 10 1 ±0.5 Serial RM-10 10 MHz B W, 50 MH z serial
AD5433 10 1 ±0.5 Parallel RU-20, CP-20 10 MHz BW, 17 ns CS pulse width
AD5440 10 2 ±0.5 Parallel RU-24 10 MHz BW, 17 ns CS pulse width
AD5451 10 1 ±0.25 Serial UJ-8 12 MHz BW, 50 MHz serial
AD5443 12 1 ±1 Serial RM-10 10 MHz BW, 50 MHz serial
AD5444 12 1 ±0.5 Serial RM-10 12 MHz BW, 50 MH z serial interface
AD5415 12 2 ±1 Serial RU-24 10 MHz BW, 50 MHz serial
AD5405 12 2 ±1 Parallel CP-40 10 MHz BW, 17 ns CS pulse width
AD5445 12 2 ±1 Parallel RU-20, CP-20 10 MHz BW, 17 ns CS pulse width
AD5447 12 2 ±1 Parallel RU-24 10 MHz BW, 17 ns CS pulse width
AD5449 12 2 ±1 Serial RU-16 10 MHz BW, 50 MHz serial
AD5452 12 1 ±0.5 Serial UJ-8, RM-8 12 MHz BW, 50 MHz serial
AD5453 14 1 ±2 Serial UJ-8, RM-8 12 MHz BW, 50 MHz serial
AD5553 14 1 ±1 Serial RM-8 4 MHz BW, 50 MHz serial clock
AD5556 14 1 ±1 Parallel RU-28 4 MHz BW, 20 ns WR pulse width
AD5555 14 2 ±1 Serial RM-8 4 MHz BW, 50 MHz serial clock
AD5557 14 2 ±1 Parallel RU-38 4 MHz BW, 20 ns WR pulse width
AD5546 16 1 ±2 Parallel RU-28 4 MHz BW, 20 ns WR pulse width
AD5545 16 2 ±2 Serial RU-16 4 MHz BW, 50 MHz serial clock
AD5547 16 2 ±2 Parallel RU-38 4 MHz BW, 20 ns WR pulse width
1
RU = TSSOP, CP = LFCSP, RM = MSOP, UJ = TSOT.
Rev. D | Page 24 of 28
Page 25
Data Sheet AD5444/AD5446
COMPLIANT TO JEDEC STANDARDS MO-187-BA
091709-A
6°
0°
0.70
0.55
0.40
5
10
1
6
0.50 BSC
0.30
0.15
1.10 MAX
3.10
3.00
2.90
COPLANARITY
0.10
0.23
0.13
3.10
3.00
2.90
5.15
4.90
4.65
PIN 1
IDENTIFIER
15° MAX
0.95
0.85
0.75
0.15
0.05
OUTLINE DIMENSIONS
Figure 54. 10-Lead Mini Small Outline Package [MSOP]
(RM-10)
Dimensions shown in millimeters
ORDERING GUIDE
Model1 Resolution (Bits) INL (LSB) Temperature Range Package Description Package Option Branding
AD5444YRM 12 ±0.5 −40°C to +125°C 10-Lead MSOP RM-10 D27
AD5444YRM-REEL 12 ±0.5 −40°C to +125°C 10-Lead MSOP RM-10 D27
AD5444YRM-REEL7 12 ±0.5 −40°C to +125°C 10-Lead MSOP RM-10 D27
AD5444YRMZ 12 ±0.5 −40°C to +125°C 10-Lead MSOP RM-10 D6X
AD5444YRMZ-REEL 12 ±0.5 −40°C to +125°C 10-Lead MSOP RM-10 D6X
AD5444YRMZ-REEL7 12 ±0.5 −40°C to +125°C 10-Lead MSOP RM-10 D6X
AD5446YRM 14 ±2 −40°C to +125°C 10-Lead MSOP RM-10 D28
AD5446YRM-REEL 14 ±2 −40°C to +125°C 10-Lead MSOP RM-10 D28
AD5446YRM-REEL7 14 ±2 −40°C to +125°C 10-Lead MSOP RM-10 D28
AD5446YRMZ 14 ±2 −40°C to +125°C 10-Lead MSOP RM-10 D7Z
AD5446YRMZ-RL7 14 ±2 −40°C to +125°C 10-Lead MSOP RM-10 D7Z
EVAL-AD5446SDZ Evaluation Board
1
Z = RoHS Compliant Part.
Rev. D | Page 25 of 28
Page 26
AD5444/AD5446 Data Sheet
NOTES
Rev. D | Page 26 of 28
Page 27
Data Sheet AD5444/AD5446
NOTES
Rev. D | Page 27 of 28
Page 28
AD5444/AD5446 Data Sheet
NOTES
©2004–2012 Analog Devices, Inc. All rights reserved. Trademarks and
reg
istered trademarks are the property of their respective owners.
D04588-0-4/12(D)
Rev. D | Page 28 of 28
Loading...