Datasheet ACS103 Datasheet (Semtech Corporation)

Page 1
ACS103 - 3 Channel, Synchronous or Asynchronous Single Fiber Modem
3 Channel, Synchronous or Asynchronous Single Fiber Modem
ACS103Acapella Optical Modem IC
Main Features:
* Enables three full-duplex serial transmission
* Link lengths up to 5 km. * Uses a single Ping Pong LED (PPLED) to both
transmit and receive data.
* Supports 7 synchronous data rates up to 64 kbps
or asynchronous data rates from DC to 19.2/
9.6 kbps.
* Supports three additional low frequency
asynchronous channels or RS-232 handshake signals: RTS, CTS, DTR and DSR.
* BER 10-9. * Digital mode, allowing the user to add an
external amplifier. Also enables the ACS103 be used in non-fiber applications e.g. IR/RF.
* ACS101 emulation mode giving 100%
compatibility with the ACS101.
General Description:
The ACS103 is a complete synchronous optical­modem controller/driver IC, supporting various user-programmable, full-duplex data-rates to 256 kbps over a single fiber. Alternatively, up to 3 channels of 64 kbps each can be carried. In 'Standard' mode, the fiber may be up to 2.5 km long, or up to 5 km in 'Double' mode.
Communicating optical-modems automatically maintain synchronisation with each other such that the receive phase of one modem is lined-up with the transmit phase of the other, compensating for the propagation delay presented by the link. Link lengths from zero to maximum distance are catered for automatically.
The ACS103 incorporates ACS101 functionality, with additional logic to support 3 channels.
Inter-IC Encoding Technique
The 3B4B encoding method is used for communication between ACS103s, thus ensuring that there is no DC component in the signal. The encoding and decoding is transparent to the user.
2
TxD1 TxD2 TxD3
TxCL
RxD1 RxD2
RxD3
RxCL
VA+
VD+
GND
Block diagram of ACS103
Digital
Filter
Digital
Filter
RS-232 Interface
DCDBRTS CTS DTR DSR XI3 XO3 RSS DR(1:4) DM(1:3) CKC SEL
XI1 XO1 XI2 XO2
FIFO
Compress
FIFO
Decompress
3B4B
Encoder
3B4B
Decoder
4 3
LED Driver
LED Receiver
Control Logic
TRC
PPLED
LDP
LDN
CNT
GND
XTAL
1
ACS103 Issue 2.03 May 1996.
Page 2
2
ACS101 Emulation mode using "SEL" input
The "SEL" input pin is normally held Low in order to configure the device in ACS103 mode. If the "SEL" input pin is allowed to pull High via an internal resistor the device will be configured in ACS101 emulation mode. In ACS101 emulation mode the device is fully compatible with the ACS101. The TxD2, TxD3 and XI3 inputs are internally disabled with the RxD2, RxD3 and XO3 outputs forced into the high impedance state. A full-duplex path then exists between TxD1 and RxD1.
Transmitter and Receiver Functions
The TxD input data of the transmitting modem is compressed, filtered, and 3B4B encoded. In the receiving modem, 3B4B encoding ensures easy extraction of the bit-clock. The received data is filtered, decoded, then stored in an output memory. The memory provides time expansion, de-jittering and frequency compensation. The data is filtered again to improve BER then directed to the RxD output pin. Signals TxD and RxD in this specification refer to the set of signals TxD1/2/3 and RxD1/2/3 respectively.
Transmit Current
The transmit current to the LED can be defined by the Transmit Current pin (TRC). The current is set to the maximum value (~100 mA) when TRC is unconnected. The current is set to the minimum value (~10 mA) when TRC is connected directly to ground. To obtain current values between minimum and maximum, TRC is connected to ground through a resistor. The resistor value R is given by:
LED current drive (mA) = 100 * (110+R)
(1100 + R) Data-rate Selection ACS103 mode SEL = 0
DR4 DR3 DR2 DR1 Data-rate Distance
(kbps)
0000 n/a 0 0 0 1 9.6 Double 0 0 1 0 19.2 Double 0 0 1 1 38.4 Double 0100 n/a 0101 n/a 0 1 1 0 DC - 4.8 Double 0111 n/a 1 0 0 0 2.4 Standard 1 0 0 1 9.6 Standard 1 0 1 0 19.2 Standard 1 0 1 1 38.4 Standard 1 1 0 0 48.0 Standard 1 1 0 1 56.0 Standard 1 1 1 0 DC - 9.6 Standard 1 1 1 1 64.0 Standard
n/a = not available
The data rates given in the previous table apply to TxD1, TxD2 and TxD3.
ACS101 mode SEL = 1
DR4 DR3 DR2 DR1 Data-rate Distance
(kbps)
0 0 0 0 256.0 Standard 0 0 0 1 9.6 Double 0 0 1 0 19.2 Double 0 0 1 1 38.4 Double 0 1 0 0 48.0 Double 0 1 0 1 192.0 Standard 0 1 1 0 DC - 19.2 Double 0 1 1 1 64.0 Double 1 0 0 0 2.4 Standard 1 0 0 1 9.6 Standard 1 0 1 0 19.2 Standard 1 0 1 1 38.4 Standard 1 1 0 0 48.0 Standard 1 1 0 1 56.0 Standard 1 1 1 0 DC - 38.4 Standard 1 1 1 1 64.0 Standard
The ACS101 mode is a single channel mode configuration - the data rates given in the previous table apply to TxD1 only.
'Standard' mode of operation is up to 2.5 km and 'Double' mode is up to 5 km. The two asynchronous modes are selected when DR3 = 1, DR2 = 1, DR1= 0. The above data-rates are obtained when used in conjunction with a crystal of 9.216 MHz. Non­standard data-rates may be generated by using the appropriate crystal frequency. For example, to generate 160 kbps data-rate in ACS101 mode, use a crystal frequency of: (160/192) * 9.216 MHz, i.e.
7.68 MHz. Other "non-standard" data-rates may be generated in the same way as long as the 5 - 10 MHz crystal range is observed.
For the data-rates 9.6, 19.2, and 38.4 kbps in ACS103 mode (9.6, 19.2, 38.4, 48 and 64 kbps in ACS101 mode), the data-rate selection pins DR3­DR1 are common to 'Standard' and 'Double' modes of operation with DR4 selecting the mode.
Modem Control Signals RSS.
The RTS/XI1, CTS/XO1, DTR/XI2, DSR/XO2, XI3 and XO3 signals may be used in either of two modes, depending on the RSS setting:
RSS = Low; data transmission mode RSS = High; modem handshake mode
RSS Low - Data Transmission Mode.
When configured in data transmission mode the inputs XI1, XI2 and XI3 are sampled continuously with the outputs appearing at XO1, XO2 and XO3 (respectively) of the far-end modem. The sample frequency for 'Standard' mode is: (crystal freq.)/1536,
ACS103 Issue 2.03 May 1996.
2
Page 3
or 6.0 kHz using the recommended crystal frequency
- 9.216 MHz. The sample frequency for 'Double' mode is: (crystal freq)/3072, or 3 kHz using the recommended crystal of 9.216 MHz.
The output filters for XO1/2/3 require a minimum over-sampling of 6 on data presented to the XI1/2/3 inputs.
consequently the jitter on the output RxD. The sample frequency is always 1/108 of the chosen clock frequency in 'Standard' mode and 1/216 in 'Double' mode. In ACS101 emulation mode the sample frequency is 1/36 of crystal clock frequency in 'Standard' mode and 1/72 of the crystal clock frequency in 'Double' mode.
In ACS101 mode the XI3 input is internally disabled and the XO3 output is forced into the high impedance state.
RSS High - Modem Handshake Mode. In modem handshake mode the control signals are
used as conventional handshake signals between the DTE (terminal) and the DCE (modem):
DSR (Data Set Ready) DCE
The DCE is powered up and asserts a Low (active level) on DSR. The DTE is informed that it is connected to a “live” DCE.
DTR (Data Terminal Ready) DTE
The DTE is powered up and asserts a Low (active level) on DTR. The DCE is informed that it is connected to a “live” DTE. If DTR is set High, the DCE responds by taking DCDB High.
RTS (Request to Send) DTE
The DTE recognises that synchronisation has been achieved (DCDB active) and asserts a Low (active level) on RTS. This constitutes a request by the DTE to send data to the far-end modem.
àà
à DTE.
àà
àà
à DCE.
àà
àà
à DCE.
àà
Integrating Capacitor
The ACS103 requires the use of an integrating ceramic capacitor of value 22 nF- 33 nF between pins CNT and GND for a crystal oscillator frequency range of 5 - 10 MHz.
DCDB
The Data Carrier Detect (DCDB) signal goes Low when the modems are locked and ready for data transmission.
PORB
The PORB pin is a single-pin alternative to the reset combination DM3 = 0, DM2 = 0, DM1 = 1. If left unconnected the input pulls High to the operational state. Selecting reset using DM1-DM3 or holding PORB Low turns off the LED and most of the digital logic. The device has been designed to power-up correctly and operate without the aid of PORB.
Transmission Clock TxCL
The ACS103 gives a choice between internally and externally generated transmission clocks (see Figure
2. Timing diagrams for set-up and hold specifications).
2
CTS (Clear to Send) DCE
The DCE recognises the active RTS signal and responds by asserting a Low (active level) on CTS. If RTS is set High the DCE responds by bringing CTS High.
DCDB (Data Carrier Detect) DCE
When synchronisation is achieved between DCEs the DCDB signal is set Low (active level). If synchronisation is lost the DCE sets DCDB and CTS High.
Crystal Clock
A crystal may be connected between the pins XLI and XLO. Alternatively, XLI may be driven directly by an external clock. The operational frequency range is 5 MHz to 10 MHz, though communicating devices must be driven at the same nominal frequency with a tolerance of 100 ppm. In synchronous mode the frequency should be 9.216 MHz, resulting in the standard range of synchronous communication frequencies selected by DR1-DR4.
For asynchronous operation, the choice of crystal clock frequency dictates the sample rate of the asynchronous data appearing at the input TxD, and
àà
à DTE.
àà
àà
à DTE.
àà
When the CKC pin is held Low, TxCL is configured as an output producing a clock at the frequency defined by DR1-DR4. Data is clocked into the device on the rising edge of the internally supplied clock.
When the CKC pin is held High, TxCL is configured as an input, and will accept an externally produced transmission clock with a tolerance of up to 500 ppm with respect to the transmission rate determined by DR1-DR4. The ACS103 performance is at its best when external changes on input pins are synchronised with internal clocks. Therefore, superior performance is likely when using the internally generated data transmission clock. If however, an externally generated transmission clock is used, then TxCL and TxD are generally asynchronous to the ACS103 internal clocks, performance in this case will be enhanced by limiting the edge speed of the TxCL and TxD signals so that they are greater than 150 ns. The modem has been designed to cope with very slow edges on inputs, without fear of metastability problems.
Receive Clock RxCL
In synchronous mode data is valid on the rising edge of RxCL clock (see Figure 2. Timing diagrams). To ensure that the average receive frequency is the
3
ACS103 Issue 2.03 May 1996.
Page 4
2
same as the transmitted frequency RxCL is generated from a Digital Phase-Lock Loop (DPLL) system. The DPLL makes periodic corrections to the output RxCL clock to compensate for differences in the crystal values, and in the case of an externally supplied transmission clock (TxCL), compensation is also made for differences in frequency between this supplied data clock and the selected clock rate (DR1­DR4). The DPLL is adaptive and will minimise the frequency of correction and jitter when the crystal values and transmission clocks are tightly toleranced.
If the ACS103 receive FIFO empties (e.g. transmissions at far-end are halted) the RxCL clock stops, therefore rising edges of the RxCL clock always correspond to valid received data bits. This enables the system designer to use the ACS103 for the transmission of packets of data with blank periods between packets. The minimum quanta of data that can be sent over the link is three bits.
In asynchronous mode the RxCL clock is turned off.
Diagnostic/Operational Modes
The diagnostic/operational modes input pins DM1­DM3 may be changed asynchronously within a window of (crystal clock period) * 1536. The diagnostic mode signals are sampled 1536 * (crystal clock period) after a change is detected on any of the DM inputs. The sampled value is taken as the valid diagnostic mode.
Diagnostic Mode Lock DM3 DM2 DM1
Full-duplex drift 0 0 0 Reset 0 0 1 Remote loop-back active 0 1 0 Full-duplex random 0 1 1 Local loop-back d ri ft 1 0 0 Full-duplex slave active 1 0 1 Full-duplex active 1 1 1
Local loopback and remote loop-back are only available in ACS101 emulation mode.
Full-duplex
In full-duplex configuration the RxCL clock of both devices tracks the average frequency of the TxCL clock of the opposing end of the link. The receiving Digital Phase-Lock Loop (DPLL) system makes periodic adjustments to the RxCL clock to ensure that the average frequency is exactly the same as the far­end TxCL clock. In this mode each TxCL is an independent master clock and each RxCL a slave clock.
Full-duplex slave
In slave mode the TxCL and the RxCL clock is derived from the TxCL clock of the opposing side of the link, such that the average frequency is exactly the same. It is therefore essential that only one modem is configured in slave mode at a time. The
CKC pin is overridden so that TxCL is always configured as an output.
Local Loopback
Local loopback is only available in ACS101 emulation mode.
In local loopback mode data is looped back inside the near-end modem and is output at its own RxD output. The data is also sent to the far-end modem; synchronisation between the modems is maintained. In local loopback mode, data received from the far­end device is ignored, except to maintain lock. When local loopback is activated the DCDB signal assumes the logic High state. If concurrent requests occur for local and remote loopback, local loopback is selected.
When RSS = 0, RTS and DTR are looped back to CTS and DSR respectively.
Remote Loopback
Remote loopback is only available in ACS101 emulation mode.
In remote loopback mode the near-end modem sends a request to the far-end modem to loopback its received data, thus returning the data. The far-end modem also outputs the received data at its RxD. Both modems are exercised completely, as well as the LEDs and the fiber optic link. Once remote loopback is established, DCDB on the near-end (initiating) modem is Low, and DCDB on the far-end modem is set High. Any data appearing on the TxD input of the far-end modem is ignored.
When RSS = 0, RTS and DTR are looped back to CTS and DSR respectively.
Drift lock
Communicating modems attain a stable state where the "transmit window" of one modem coincides with the "receive window" of the other allowing for delay through the optical link. Adjustments to machine cycles are made automatically during operation to compensate for differences in crystal frequencies which cause loss of synchronisation.
Using drift lock, synchronisation described above depends on a difference in the crystal frequencies at each end of the link, the greater the difference the faster the locking. Therefore, if the difference between crystal frequencies is very small (a few ppm), automatic locking may take tens of seconds.
Active Lock Mode
Active lock mode may be used to accelerate synchronisation of a pair of communicating modems. This mode synchronises the modems with less than 250 ms delay, by adjusting the machine cycle of the modem. Active lock reduces the machine cycle of the device by 0.5 % ensuring rapid lock. After
ACS103 Issue 2.03 May 1996.
4
Page 5
synchronisation the machine cycle reverts automatically to normal.
Note that only one device can be configured in active lock at any one time, and thus the DM pins must not be permanently wired High on both devices in a production system. Active lock mode is usually invoked on power-up. One common way of temporarily invoking active lock is to adopt the standard RC time-constant method. This is achieved on the ACS103 by connecting DM1, DM2 and DM3 together, and attaching that node to an RC arrangement, i.e. with the capacitor to 5 V and the resistor to ground. This creates a 5 V à 0 V ramp on power-up. The RC time-constant should be Ca. 1 second.
Random Lock
This is a new mode of operation (over the ACS100), both ends of a link can be permanently configured in this mode (i.e. with hard-wired DM1-DM3 pins), which will achieve lock in typically 1 second, and worst case 5 seconds.
detected then ERD will go High and will remain High until ERD is initialised. ERD may be initialised by applying reset DM1-DM3 or PORB, or by removing the fiber-optic cable from one side of the link thereby forcing the device temporarily out of lock. ERD is only an indication and is not a substitute for BER tests.
LED Considerations
Since LEDs from different suppliers may emit different wavelengths, it is recommended that the LEDs in a communicating pair of modems are obtained from the same supplier. The emission spectrum of an LED is a function of temperature, so a temperature difference between the ends of a link reduces the responsivity of the receiving diode. This results in a reduction in the link budget. Information is given in the LED suppliers’ data sheets. The following manufacturers have LEDs that have been successfully tested with the ACS103 and Acapella will be glad to assist with contact names and addresses on request.
2
Like active lock, random lock will operate even when both ends of the link are driven by identical clock frequencies (0 ppm). Random lock mode is compatible with drift lock available on the ACS100.
Mixing Lock modes
It is possible to mix all combinations of locking modes once the modems are locked, however, prior to synchronisation two modems configured in active lock will not operate. Normally, random lock will be the preferred mode. The effect of mixing locking modes on locking speed is tabulated below:
Device A Device B Locking Speed Mode Mode
Drift Drift Drift Drift Active Active Drift Random Random Active Active Not allowed Active Random Random Random Random Random
LIN (Lock Indicator)
LIN goes High when synchronisation or 'lock' is achieved. Lock is normally an invert of DCDB. But unlike DCDB is not affected by the status of RTS and DTR, or the selected diagnostic mode.
ERD (Error Detector)
This signal can be used to give an indication of the quality of the optical link. Even when a DC signal is applied to the TxD and TxCL inputs, the ACS103 transmits approximately 256 kbps over the link in each direction. This control data is used to maintain the timing and the relative positioning of transmit and receive windows. The transmit data and the control data is constantly monitored to make sure it is compatible with the 3B4B format. If an error is
Suppliers:
ABB-Hafo (e.g. 1A-212-connector) Acapella (e.g. A-connector) GCA (e.g. 1A-212-connector) Honeywell (e.g. HFE4214-013, HFE4404-013) Optek (e.g. OPF372, OPF322)
Most suppliers support the standard range of fiber connectors, e.g. ST, SMA and FC.
Power Supply Decoupling
The ACS103 contains a highly sensitive amplifier, capable of responding to extremely low current levels. To exploit this sensitivity it is important to reduce external noise to a low level compared to the input signal from the LED. The modem should have an independent power trace to the point where power enters the board.
Figure 3. shows the recommended power supply decoupling. The LED should be sited very close to the LDN and LDP pins. A generous ground plane should be provided, especially around the sensitive LDN and LDP pins. The modem should be protected from EMI/RFI sources in the standard ways.
Link Budgets
The link budget is the difference between the power coupled to the fiber via the transmit LED and the power required to realise a current of 650 nA (minimum amplifier sensitivity) via the receive LED.The link budget is normally specified in dB or dBm, and represents the maximum attenuation allowed between communicating LEDs. The budget is utilised in terms of the cable length, cable connectors and splices. It usually includes an operating margin to allow for degradation in LED performance.
5
ACS103 Issue 2.03 May 1996.
Page 6
2
The power coupled to the cable is a function of the efficiency of the LED, the current applied to the LED and the diameter of the fiber optic cable. The larger the cable diameter the greater the power coupled. The conversion current produced by the receive diode is a function of the LED efficiency and the cable diameter. The conversion efficiency is measured in terms of its ability to convert the available power to current, known as the responsivity, given by (A/W). Some examples of link budgets are given in the Table 1., though note that significantly better "A" spec. LEDs available, e.g. from Acapella. “A” spec. LEDs can offer > 12 dB link budget on 50 µm fiber.
Maximum Link Length
The internal timing chain within the ACS103 limits the link length to 2.5 km ('Standard' mode) and 5 km ('Double' mode) with a crystal frequency of
9.216 MHz. However, the maximum link length as determined by the ACS103 timing chain is inversely proportional to the crystal frequency. Please contact Acapella if you wish to discuss longer links.
TxD inputs
recommended choice since it is further away from the sensitive analogue pins. However, pin 41 is available for designers if required.
Digital Mode
The ACS103 may be used as a controller and data buffer which allows the device to be used with an external amplifier and receiver, e.g. for non-fiber applications. Check with Acapella for details.
Data delay and skew
The data delay in synchronous mode is typically 48 data-bit periods and worst case 100 data-bit periods. When configured in asynchronous mode the worst case data delay is 300 µs at 9.216 MHz and 550 µs at 5 MHz. The additional data transmission channels (XI1/2/3) are delayed by up to 1.2 ms in 'Standard' mode and up to 2.4 ms in 'Double' mode when used with a crystal frequency of 9.216 MHz. For other crystal values the delay changes inversely proportional to the frequency of operation.
The worst case data skews between the main data channels TxD1/RxD1, TxD2/RxD2 and TxD3/RxD3 across the link are as follows.
There is a choice of pins for TxD1, pins 12 and 41. Only one input should be used. The other input will pull-up to VDD via an internal resistor. Pin 12 is the
1 DR3 2 DR1 3IC 4 DM1 5 RxD1 6IC 7 XO3 8IC
9NC 10 RTS / XI1 11 TxD3 12 TxD1 13 VD+ 14 XTI 15 XTO 16 CKC 17 TxCL 18 RxCL 19 XI3 20 DM2 21 SEL 22 DM3 23 GND 24 DTR / XI2 25 TxD2 26 ERD 27 NC 28 IC 29 RxD2 30 PORB 31 RxD3 32 CTS / XO1 33 DSR / XO2 34 DCDB
9
8
7
6
5
4
3
10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26
27
ACAPELLA
ACS103
1-Fiber Modem
28
29
30
31
32
33
Figure 1. Top view of 68 PLCC package
NC = Not Connected IC = Internally Connected
Synchronous : zero data bits. Asynchronous :216 * (crystal clock period).
2
1
68
67
66
65
64
63
62
61
60 59 58 57 56 55 54 53 52 51 50 49 48 47 46 45
34
35
36
37
38
39
40
41
42
43
44
VD+ 68 VD+ 67 GND 66 GND 65 DR2 64 TRC 6 3 DR4 62 NC 61 NC 60 NC 59 NC 58 NC 57 VG 56 VA+ 55 CON2 54 LDP 53 NC 52 NC 51 LDN 50 CON1 49 CNT 48 GND 47 NC 46 NC 45 NC 44 NC 43 IC 42 TXD1 41 LIN 40 RSS 39 VD+ 38 VD+ 37 GND 36 GND 35
ACS103 Issue 2.03 May 1996.
6
Page 7
t
wh
t
wl
t
r
t
f
TxCL and RxCL clock pulse widths
TxCL RxCL
t
tht t
sut
TxD RxD
Transmit set-up and hold times Receive set-up and hold times
Figure 2. Timing diagrams
90 %
10 %
90 %
10 %
Digital Outputs rise and fall times
t
sur
hr
2
V+
47 µH
+5V
47 µH
GND
All capacitors must be placed very close to the ACS103.
DTE ACS103 ACS103 DCE
100
47µF 100 nF 100 nF
100 nF
10
GND
VA+
VD+
VG GND
ACS103
CNT
22 - 33 nF
Figure 3. Recommended power supply layout
TxD1 RxD1
RTS / XI1 CTS / XO1
TxD2 RxD2
DTR / XI2 DSR / XO2
TxD3 RxD3
XI3 XO3
Single Fiber Link
VD+ pins are 13, 37, 38, 67 and 68. GND pins are 23, 35, 36, 47, 65 and 66.
CON1
CON2
GND
RxD1 TXD1
CTS / XO1 RTS / XI1
RxD2 TxD2
DSR / XO2 DTR / XI2
RxD3 TxD3
XO3 XI3
Pin 49 and Pin 54 should be connected together
Figure 4. 6 Full-duplex channels in data transmission mode
7
ACS103 Issue 2.03 May 1996.
Page 8
Link Budget Examples
Cable 200 micron 100 micron 62.5 micron 50 micron
Typical transmit couple power to fiber (µW) 1200 260 100 40 Minimum LED responsivity (A/W) 0.05 0.06 0.1 0.12 Available current (µA) 60 15.6 10 4 .8
Minimum ACS103 sensitivity (nA) 650 650 650 650 Link Budget (dB) 20 14 12 8 Above examples using nominal "B" spec. LED diodes. "A" spec. LEDs offer superior performance, e.g. > 12 dB link budget
on 50 µm fiber. "A" spec. LEDs are available from Acapella.
Absolute Maximum Ratings
2
Parameter Symbol Min Max Units
Power supply VD+ and VA+ (VDD = VD+ or VA+)
Input voltage (non-supply pins)
Input current (except LDN,LDP,CNT,VG)
Input current ( LDN,LDP,CNT)
Storage temperature Tstor -50 160 ºC
VDD -0.3 6.0 V
Vin GND - 0.3 VDD + 0.3 V
Iin - 10.0 mA
Iin - 1.0 mA
Operating Conditions
Parameter Symbol Min Typ Max Units
Power supply (VA+ and VD+)
Ambient temperature range TA -40 - 85 ºC
V+ 4.75 5.0 5.25 V
Static Digital Input Characteristics (for specified operating conditions)
Input pins: DR 1/2/3/4 , DM 1/2/3, SEL, CKC, RSS, TXD1/2/3, RTS, DTR, XI3, XTI, PORB, TxCL(input).
Parameter Symbol Min Typ Max Units
Vin High (except PORB) Vih 2.0 - - V
Vin Low (except PORB) Vil - - 0.8 V
Vin High (PORB) Vih 0.8 * VD+ - - V
Vin Low (PORB) Vil - - 0.2 * VD+ V
Pull-up resistor (except XTI and TxCL)
Input current (Note 1) Iin - - 100 µA
Note 1: Input current is mainly attributed to pull-up resistor, so it applies when input is Low. The High input current is < +/-10 µA.
ACS103 Issue 2.03 May 1996.
PU 50k 125k 340k
8
Page 9
Static Digital Output Characteristics (for specified operating conditions)
Output pins: RxD1/2/3, CTS, DSR, XO3, DCDB, LIN, ERD, XLO, RxCL, TxCL(output)
Parameter Symbol Min Typ Max Units
Vout Low (Iout = 4mA) Vol 0 - 0.5 V
Vout High (Iout = 4mA) Voh VDD-0.5 - - V
Max load capcitance Cl - - 50 pF
XLO (Note 2) - - - - pF
Note 2: XLO does not have a drive capability other than that of the load presented by a parallel resonant crystal and appropriate padding
capacitor.
Dynamic Characteristics
Parameter Symbol Min Typ Max Units
Crystal frequency (XTI, XTO)
External clock (XTI) High or Low time
RxD and TxD data rate ACS101 mode Synchronous standard double Asynchronous standard double
RxD and TxD data rate ACS103 mode Synchronous standard double Asynchronous standard double
RxCL and TxCL duty cycle (with TxCL = output)
Frequency deviation at TxCL from selected value (with TxCL = input)
frc 5 9.216 10 MHz
fcl 40 - 60 %
fckc
fckc
twh
twl
Fd - - 500 ppm
2.4
9.6 DC DC
2.4
9.6 DC DC
- 50 - %
- 256 64
38.4
19.2
- 64
38.4
9.6
4.8
kbps
kbps
2
TxD to TxCL set-up time tsut 300 - - ns
TxD to TxCL hold time tht 25 - - ns
RxD to RxCL set-up time tsur - 0.5 *1/RxCL - ns
RxD to RxCL hold time thr - 0.5 *1/RxCL - ns
Digital output - fall time tf - - 100 ns
Digital output - rise time tr - - 100 ns
Power consumption: TCL floating (or 100kOhms) TCL tied to GND (Note 3)
Pc -
200 150
300 250
Note 3: Power consumption assumes that digital outputs drive CMOS loads.
9
ACS103 Issue 2.03 May 1996.
mW
Page 10
Matching Characteristics (for specified operating conditions)
Parameter Symbol Min Typ Max Units
Crystal tolerance use parallel resonate crystal and recommended padding capacitors
Amplifier sensitivity input current standard double
Maximum amplifier input current Imax 30 50 - mA
Ct -100 0 100 ppm
Irec 650
500
500 300
- nA
2
Rtrc placed between TRC and GND Rtrc 0 - -
LED current with TRC floating: peak current average curent (Note 4)
LED capacitance with Vr = 0 Volts (Note 5)
LED leakage current Vr = 1.8 Volts
LED reverse bias Vr 1.3 1.5 1.8 V
Note 4: The LED is switched on for approximately 1/5th of the time with a cycle of 160 µs at 9.216 MHz.
5: The ACS103 is at its best with low capacitance LEDs - Acapella is able to supply LEDs with lower than 20 pF capacitance.
Icur 70
14
Cled - - 100 pF
Cl - 1 100 nA
-
-
130
26
For additional information, contact the following:
Semtech Corporation Advanced Communications Products
E-Mail: AdvCom@semtech.com Internet: http://www.semtech.com
mA
USA: 652 Mitchell Road, Newbury Park, CA 91320-2289
Tel: +1 805 498 2111, Fax: +1 805 498 3804
FAR EAST: 11F, No. 46, Lane 11, Kuang Fu North Road, Taipei, Taiwan, R.O.C.
Tel: +886 2 2748 3380, Fax: +886 2 2748 3390
EUROPE: Delta House, Chilworth Research Centre, Southampton, Hants, SO16 7NS, UK
Tel: +44 23 80 769008, Fax: +44 23 80 768612
ISO9001
CERTIFIED
Semtech reserves the right to change specifications on catalog devices without notice.© Copyright Semtech Corp 2000
ACS103 Issue 2.03 May 1996.
10
Loading...