Datasheet 74VHC05TTR, 74VHC05MTR, 74VHC05M Datasheet (SGS Thomson Microelectronics)

1/8June 2001

■ HIGH SPEED: t

PD

= 3.8ns (TYP.) at VCC = 5V

■ LOW POWER DISSIPATION:

I

CC

= 2 µA (MAX.) at TA=25°C

■ HIGH NOISE IMMUNITY:

V

NIH

= V

NIL

= 28% VCC (MIN.)

■ POWER DOWN PROTECTION ON INPUTS

■ OPERATING VOLTAGE RANGE:

V

CC

(OPR) = 2V to 5.5V

■ PIN AND FUNCTION COMPATIBLE WITH

74 SERIES 05

■ IMPROVED LATCH-UP IMMUNITY

■ LOW NOISE: V

OLP

= 0.8V (MAX.)

DESCRIPTION

The 74VHC05 is a n advanced high-speed CM OS
OPEN DRAIN HEX INVERTER fabricated with
sub-micron silicon gate and double-layer metal
wiring C

2

MOS technology.
The internal circuit is composed of 3 stages
including buffer ou tput, which provides high no ise
immunity and stable output.
Power down protection is provided on all inputs
and 0 to 7V can be accepted on inputs with no

regard to the supply voltage. This device can be
used to interface 5V to 3V.
All inputs and outputs are equipped with
protection circuits against stat ic discharge, giving
them 2KV ESD immunity and transient excess
voltage.

74VHC05

HEX INVERTER (OPEN DRAIN)

PIN CONNECTION AND IEC LOGIC SYMBOLS

ORDER CODES

PACKAGE TUBE T & R

SOP 74VHC05M 74VHC05MTR

TSSOP 74VHC05TTR

TSSOPSOP

74VHC05

2/8

INPUT EQUIVALENT CIRCUIT PIN DESCRIPTION

TRUTH TABLE

Z: High Impedance

ABSOLUTE MAXIMUM RATINGS

Absolute Maximum Ratings are those values beyond which damage to the device may occur. Functional operation under these conditions is
not implied

RECOMMENDED OPERATING CONDITIONS

1) VIN from 30% to 70% of V

CC

PIN No SYMBOL NAME AND FUNCTION

1, 3, 5, 9, 1 1,

13

1A to 6A Data Inputs

2, 4, 6, 8, 10,

12

1Y to 6Y Data Outputs

7 GND Ground (0V)

14

V

CC

Positive Supply Voltage

AY

LZ

HL

Symbol Parameter Value Unit

V

CC

Supply Voltage

-0.5 to +7.0 V

V

I

DC Input Voltage

-0.5 to +7.0 V

V

O

DC Output Voltage -0.5 to VCC + 0.5

V

I

IK

DC Input Diode Current

- 20 mA

I

OK

DC Output Diode Current

± 20 mA

I

O

DC Output Current

± 25 mA

I

CC

or I

GND

DC VCC or Ground Current

± 75 mA

T

stg

Storage Temperature

-65 to +150 °C

T

L

Lead Temperature (10 sec)

300 °C

Symbol Parameter Value Unit

V

CC

Supply Voltage

2 to 5.5 V

V

I

Input Voltage

0 to 5.5 V

V

O

Output Voltage 0 to V

CC

V

T

op

Operating Temperature

-55 to 125 °C

dt/dv

Input Rise and Fall Time (note 1) (V

CC

= 3.3 ± 0.3V)

(V

CC

= 5.0 ± 0.5V)

0 to 100

0 to 20

ns/V

74VHC05

3/8

DC SPECIFICATIONS

AC ELECTRICAL CHARACTERISTICS(Input t

r

= tf = 3ns)

(*) Vol tage range is 3.3V ± 0.3V
(**) Voltage range is 5.0V ±

0.5V

Symbol Parameter

Test Condition Value

Unit

V

CC

(V)

T

A

= 25°C

-40 to 85°C -55 to 125°C

Min. Typ. Max. Min. Max. Min. Max.

V

IH

High Level Input
Voltage

2.0 1.5 1.5 1.5
V

3.0 to

5.5

0.7V

CC

0.7V

CC

0.7V

CC

V

IL

Low Level Input
Voltage

2.0 0.5 0.5 0.5
V

3.0 to

5.5

0.3V

CC

0.3V

CC

0.3V

CC

V

OL

Low Level Output
Voltage

2.0

I

O

=50 µA

0.0 0.1 0.1 0.1

V

3.0

I

O

=50 µA

0.0 0.1 0.1 0.1

4.5

I

O

=50 µA

0.0 0.1 0.1 0.1

3.0

I

O

=4 mA

0.36 0.44 0.55

4.5

I

O

=8 mA

0.36 0.44 0.55

I

OZ

High Impedance
Output Leakage
Current

5.5

V

I

= VIH or V

IL

VO = VCC or GND

±0.25 ± 2.5 ± 2.5 µA

I

I

Input Leakage
Current

0 to

5.5

V

I

= 5.5V or GND

± 0.1 ± 1 ± 1 µA

I

CC

Quiescent Supply
Current

5.5

V

I

= VCC or GND

22020µA

Symbol Parameter

Test Condition Value

Unit

V

CC

(V)

C

L

(pF)

T

A

= 25°C

-40 to 85°C -55 to 125°C

Min. Typ. Max. Min. Max. Min. Max.

t

PZL

Output Enable
Time

3.3

(*)

15

R

L

= 1 KΩ

5.0 7.1 1.0 8.5 1.0 8.5

ns

3.3

(*)

50

R

L

= 1 KΩ

7.5 10.6 1.0 12.0 1.0 12.0

5.0

(**)

15

R

L

= 1 KΩ

3.8 5.5 1.0 6.5 1.0 6.5

5.0

(**)

50

R

L

= 1 KΩ

5.3 7.5 1.0 8.5 1.0 8.5

t

PLZ

Output Disable
Time

3.3

(*)

50

R

L

= 1 KΩ

7.5 10.6 1.0 12.0 1.0 12.0
ns

5.0

(**)

50

R

L

= 1 KΩ

5.3 7.5 1.0 8.5 1.0 8.5

74VHC05

4/8

CAPACITIVE CHARACTERISTICS

1) CPD is defined as the value of the IC’s internal equivalent capacitance which is calculated from the operating current consumption without

load. (Refer to Test Circuit). Average operating current can be obtained by the following equation. I

CC(opr)

= CPD x VCC x fIN + ICC/6 (per gate)

DYNAMIC SWITCHING CHARACTERISTICS

1) Worst c ase package.

2) Max number of output s defined as (n). Data inputs ar e driven 0V to 5.0V, (n-1) outputs switchin g and one output at GND.

3) Max number of data inputs (n) switching. (n-1) switching 0V to 5.0V. Inputs under test switching: 5.0V to threshold (V

ILD

), 0V to threshold

(V

IHD

), f=1MHz.

Symbol Parameter

Test Condition Value

Unit

T

A

= 25°C

-40 to 85°C -55 to 125°C

Min. Typ. Max. Min. Max. Min. Max.

C

IN

Input Capacitance

6101010pF

C

OUT

Output
Capacitance

8pF

C

PD

Power Dissipation
Capacitance
(note 1)

3pF

Symbol Parameter

Test Condition Value

Unit

V

CC

(V)

T

A

= 25°C

-40 to 85°C -55 to 125°C

Min. Typ. Max. Min. Max. Min. Max.

V

OLP

Dynamic Low
Voltage Quiet
Output (note 1, 2)

5.0

C

L

= 50 pF

0.4 0.8

V

V

OLV

-0.8 -0.4

V

IHD

Dynamic High
Voltage Input
(note 1, 3)

5.0 3.5 V

V

ILD

Dynamic Low
Voltage Input
(note 1, 3)

5.0 1.5 V

74VHC05

5/8

TEST CIRCUIT

CL = 15/50pF or e qui valent (inc lu des jig and probe capacitance)
R

L

= R1 = 1KΩ or equivalent

R

T

= Z

OUT

of pulse generator (typically 50Ω)

WAVEFORM: PROPAGATION DELAYS (f=1MHz; 50% duty cycle)

74VHC05

6/8

DIM.

mm. inch

MIN. TYP MAX. MIN. TYP. MAX.

A 1.75 0.068
a1 0.1 0.2 0.003 0.007
a2 1.65 0.064

b 0.35 0.46 0.013 0.018
b1 0.19 0.25 0.007 0.010

C 0.5 0.019
c1 45° (typ.)

D 8.55 8.75 0.336 0.344

E 5.8 6.2 0.228 0.244

e 1.27 0.050
e3 7.62 0.300

F 3.8 4.0 0.149 0.157

G 4.6 5.3 0.181 0.208

L 0.5 1.27 0.019 0.050

M 0.68 0.026

S8° (max.)

SO-14 MECHANICAL DATA

PO13G

74VHC05

7/8

DIM.

mm. inch

MIN. TYP MAX. MIN. TYP. MAX.

A 1.2 0.047

A1 0.05 0.15 0.002 0.004 0.006

A2 0.8 1 1.05 0.031 0.039 0.041

b 0.19 0.30 0.007 0.012

c 0.09 0.20 0.004 0.0089

D 4.9 5 5.1 0.193 0.197 0.201

E 6.2 6.4 6.6 0.244 0.252 0.260

E1 4.3 4.4 4.48 0.169 0.173 0.176

e 0.65 BSC 0.0256 BSC

K0° 8°0° 8°

L 0.45 0.60 0.75 0.018 0.024 0.030

TSSOP14 MECHANICAL DATA

c

E

b

A2

A

E1

D

1

PIN 1 IDENTIFICATION

A1

L

K

e

0080337D

74VHC05

8/8

Information furnished is bel ieved to be accurate and reliable. However, STMicroe lectronics assumes no responsibility for the
consequences of use of such information nor for any infringement of patents or other rights of third parties which may result from
its use. No li cense is granted by implica tion or otherwise under any patent or patent righ ts of S TMic roelec tronics. Specifications
mentioned in this publication ar e subject to change without notice. This publication supersedes and replaces all information
previously supplied. S TMicroelectronics products are not authorized for use as critica l components in life suppo rt devices or
systems without express written approval of STMicroelectronics.

© The ST logo is a registered trademark of STMicroelectronics

© 2001 STM icroelectronics - Prin ted in Italy - All Rights Reserved

STMicr o el ectronics GROU P OF COMPANIE S

Australi a - Brazil - China - Finland - France - Germany - Hong Kong - India - Italy - Japan - Malay sia - Malta - Morocco

Singapo re - Spain - Swe den - Switzerl and - United K i ngdom

© http://www.st.com