Datasheet 74VCX16373TTR Datasheet (SGS Thomson Microelectronics)

1/12February 2003

■ 3.6V TOLERANT INPUTS AND OUTPUTS

■ HIGH SPEED :

t

PD

= 3.0 ns (MAX.) at VCC=3.0to3.6V

t

PD

= 3.4 ns (MAX.) at VCC=2.3to2.7V

t

PD

= 6.8 ns (MAX.) at VCC=1.8V

■ POWER DOWN PROTECTION ON INPUTS

AND OUTPUTS

■ SYMMETRICAL OUTPUT IMPEDANCE:

|I

OH

|=IOL= 24mA (MIN) at VCC=3.0V

|I

OH

|=IOL= 18mA (MIN) at VCC=2.3V

|I

OH

|=IOL=6mA(MIN)atVCC=1.8V

■ OPERATING VOLTAGE RANGE:

V

CC

(OPR) = 1.8V to 3.6V

■ PIN AND FUNCTION COMPATIBLE WITH

74 SERIES 16373

■ LATCH-UP PERFORMANCE EXCEEDS

300mA (JESD 17)

■ ESD PERFORMANCE:

HBM > 2000V (MIL STD 883 method 3015);
MM > 200V

DESCRIPTION

The 74V CX16373 i s a low voltage CMOS 16 BIT
D-TYPE LATCH with 3 STATE OUTPUTS NON
INVERTING fabricated with sub-micron silicon
gate and five-layer metal wiring C

2

MOS
technology. It is ideal for low power and very high
speed 1.8 to 3.6V applications; it can be interfac ed
to 3.6V signal environment for both inputs and
outputs.
These 16 bit D-TY PE latches are bite controlled
by two latch enable inputs (nLE) and two output
enable inputs (OE

).
While the nLE input is held at a high level, the nQ
outputs will follow the data input precisely.
When the nLE is taken low, the nQ outputs w ill be
in a normal logic state (high or low logic level) and
while high level the outputs w il l be in a high
impedance state.
All inputs and outputs are equipped with
protection circuits against static discharge, givi ng
them 2KV ESD immunit y and transient ex c ess
voltage.

74VCX16373

LOW VOLTAGE CMOS 16-BIT D-TYPE LATCH (3-STATE)

WITH 3.6V TOLERANT INPUTS AND OUTPUTS

ORDER CODES

PACKAGE TUBE T & R

TSSOP 74VCX16373TTR

TSSOP

PIN CO NNE CTION

74VCX16373

2/12

INPUT AND OUTPUT EQUIVALENT CIRCUIT

PIN DESCRIPTION

TRUTH TABLE

X : Don‘t Care
Z : High Impedance
* : Qoutputs arelatched at the time when the LE input is taken low

logiclevel.

IEC LOGIC SYMBOLS

PIN No SYMBOL NAME AND FUNCTION

1 1OE

3 State Output Enable
Input (Active LOW)

2, 3, 5, 6, 8, 9,

11, 12

1Q0 to 1Q7 3-State Outputs

13,14, 16,17,

19, 20, 22, 23

2Q0 to 2Q7 3-State Outputs

24 2OE

3 State Output Enable
Input (Active LOW)

25 2LE Latch Enable Input

36,35, 33,32,

30, 29, 27, 26

2D0 to 2D7 Data Inputs

47,46, 44,43,

41, 40, 38, 37

1D0 to 1D7 Data Inputs

48 1LE Latch Enable Input

4, 10, 15, 21,
28, 34, 39, 45

GND Ground (0V)

7, 18, 31, 42 V

CC

Positive Supply Voltage

INPUTS OUTPUT

OE

LE D Q

HXX Z

L L X NO CHANGE *
LHL L
LHH H

74VCX16373

3/12

LOGIC DIAGRAM

This logic diagram has not to be used to estimate propagation delays

ABSOLUTE MAXIMUM RATINGS

Absolute Maximum Ratings are those values beyond which damage to the device may occur. Functional operation under these conditions is
not implied

1) I

O

absolute maximum rating must be observed

2) V

O

<GND,VO>V

CC

RECOMMENDED OPERATING CONDITIONS

1) VINfrom0.8Vto 2V at VCC=3.0V

Symbol Parameter Value Unit

V

CC

Supply Voltage

-0.5 to +4.6 V

V

I

DC Input Voltage

-0.5 to +4.6 V

V

O

DC Output Voltage (OFF State)

-0.5 to +4.6 V

V

O

DC Output Voltage (High or Low State) (note 1) -0.5 to VCC+ 0.5

V

I

IK

DC Input Diode Current

-50 mA

I

OK

DC Output Diode Current (note 2)

-50 mA

I

O

DC Output Current

± 50 mA

I

CC

or I

GND

DC VCCor Ground Current per Supply Pin

± 100 mA

P

D

Power Dissipation

400 mW

T

stg

Storage Temperature

-65 to +150 °C

T

L

Lead Temperature (10 sec)

300 °C

Symbol Parameter Value Unit

V

CC

Supply Voltage

1.8 to 3.6 V

V

I

Input Voltage

-0.3 to 3.6 V

V

O

Output Voltage (OFF State)

0 to 3.6 V

V

O

Output Voltage (High or Low State) 0 to V

CC

V

I

OH,IOL

High or Low Level Output Current (VCC= 3.0 to 3.6V)

± 24 mA

I

OH,IOL

High or Low Level Output Current (VCC= 2.3 to 2.7V)

± 18 mA

I

OH,IOL

High or Low Level Output Current (VCC= 1.8V)

± 6mA

T

op

Operating Temperature

-55 to 125 °C

dt/dv Input Rise and Fall Time (note 1) 0 to 10 ns/V

74VCX16373

4/12

DC SPECIFICATIONS (2.7V < VCC< 3.6V unless otherwise specified)

Symbol Parameter

Test Condition Value

Unit

V

CC

(V)

-40to85°C -55to125°C

Min. Max. Min. Max.

V

IH

High Level Input
Voltage

2.7to3.6

2.0 2.0
V

V

IL

Low Level Input
Voltage

0.8 0.8

V

OH

High Level Output
Voltage

2.7to3.6

IO=-100 µAVCC-0.2 VCC-0.2

V

2.7

I

O

=-12 mA

2.2 2.2

3.0

I

O

=-18 mA

2.4 2.4

I

O

=-24 mA

2.2 2.2

V

OL

Low Level Output
Voltage

2.7to3.6

IO=100 µA

0.2 0.2
V

2.7

I

O

=12 mA

0.4 0.4

3.0

I

O

=18 mA

0.4 0.4

I

O

=24 mA

0.55 0.55

I

I

Input Leakage
Current

2.7to3.6

V

I

= 0 to 3.6V

± 5 ± 5 µA

I

off

Power Off Leakage
Current

0

V

I

or VO= 0 to 3.6V

10 10 µA

I

OZ

High Impedance
Output Leakage
Current

2.7to3.6

V

I=VIH

or V

IL

VO= 0 to 3.6V

± 10 ± 10 µA

I

CC

Quiescent Supply
Current

2.7to3.6

VI=VCCor GND

20 20

µA

V

I

or VO=VCCto

3.6V

± 20 ± 20

∆I

CC

ICCincr. per Input

2.7to3.6

VIH=VCC-0.6V

750 750 µA

74VCX16373

5/12

DC SPECIFICATIONS (2.3V < VCC< 2.7V unless otherwise specified)

DC SPECIFICATIONS (1.8V <

VCC< 2.3V unless otherwise specified)

Symbol Parameter

Test Condition Value

Unit

V

CC

(V)

-40to85°C -55to125°C

Min. Max. Min. Max.

V

IH

High Level Input
Voltage

2.3to2.7

1.6 1.6
V

V

IL

Low Level Input
Voltage

0.7 0.7

V

OH

High Level Output
Voltage

2.3to2.7

IO=-100 µAVCC-0.2 VCC-0.2

V

2.3

I

O

=-6 mA

2.0 2.0

I

O

=-12 mA

1.8 1.8

I

O

=-18 mA

1.7 1.7

V

OL

Low Level Output
Voltage

2.3to2.7

IO=100 µA

0.2 0.2
V

2.3

I

O

=12 mA

0.4 0.4

I

O

=18 mA

0.6 0.6

I

I

Input Leakage
Current

2.3to2.7

V

I

= 0 to 3.6V

± 5 ± 5 µA

I

off

Power Off Leakage
Current

0

V

I

or VO= 0 to 3.6V

10 10 µA

I

OZ

High Impedance
Output Leakage
Current

2.3to2.7

V

I=VIH

or V

IL

VO= 0 to 3.6V

± 10 ± 10 µA

I

CC

Quiescent Supply
Current

2.3to2.7

VI=VCCor GND

20 20

µA

V

I

or VO=VCCto

3.6V

± 20 ± 20

Symbol Parameter

Test Condition Value

Unit

V

CC

(V)

-40to85°C -55to125°C

Min. Max. Min. Max.

V

IH

High Level Input
Voltage

1.8to2.3

0.7 VCC 0.7 VCC V

V

IL

Low Level Input
Voltage

0.2 VCC 0.2 VCC V

V

OH

High Level Output
Voltage

1.8

IO=-100 µAVCC-0.2 VCC-0.2

V

I

O

=-6 mA

1.4 1.4

V

OL

Low Level Output
Voltage

1.8

IO=100 µA

0.2 0.2
V

I

O

=6 mA

0.3 0.3

I

I

Input Leakage
Current

1.8

V

I

= 0 to 3.6V

± 5 ± 5 µA

I

off

Power Off Leakage
Current

0

V

I

or VO= 0 to 3.6V

10 10 µA

I

OZ

High Impedance
Output Leakage
Current

1.8

V

I=VIH

or V

IL

VO= 0 to 3.6V

± 10 ± 10 µA

I

CC

Quiescent Supply
Current

1.8

VI=VCCor GND

20 20

µA

V

I

or VO=VCCto

3.6V

± 20 ± 20

74VCX16373

6/12

DYNAMIC SWITCHING CHARA CTERISTICS (Ta= 25°C, Input tr=tf= 2.0ns, CL= 30pF, RL= 500Ω)

1) Number of outputsdefined as "n".Measured with "n-1"outputs switching from HIGH to LOW or LOW to HIGH. The remainingoutput is
measured in the LOW state.

2) Number of outputsdefined as "n".Measured with "n-1"outputs switching from HIGH to LOW or LOW to HIGH. The remainingoutput is
measured in the HIGH state.

3) Parameters guaranteed by design.

AC ELECTRICAL C HARACTERISTICS (CL= 30pF, RL= 500Ω, Input tr=tf= 2.0ns)

1) Skew is defined as the absolute value of the difference between the actual propagation delay for any two outputs of the same device switch­ing in the same direction, either HIGH or LOW (t

OSLH

=|t

PLHm-tPLHn

|, t

OSHL

=|t

PHLm-tPHLn

|)

2) Parameter guaranteed by design

Symbol Parameter

Test Condition Value

Unit

V

CC

(V)

T

A

=25°C

Min. Typ. Max.

V

OLP

Dynamic Low Voltage Quiet
Output (note 1, 3)

1.8
V

IL

=0V

V

IH=VCC

0.25
V2.5 0.6

3.3 0.8

V

OLV

Dynamic Low Voltage Quiet
Output (note 1, 3)

1.8
V

IL

=0V

V

IH=VCC

-0.25
V2.5 -0.6

3.3 -0.8

V

OHV

Dynamic High Voltage Quiet
Output (note 2, 3)

1.8
V

IL

=0V

V

IH=VCC

1.5
V2.5 1.9

3.3 2.2

Symbol Parameter

Test Condition Value

Unit

V

CC

(V)

-40 to 85 °C -55 to 125 °C

Min. Max. Min. Max.

t

PLHtPHL

Propagation Delay
Time Dn to Qn

1.8 1.5 6.8 1.5 8.0
ns2.3 to 2.7 1.0 3.4 1.0 4.0

3.0 to 3.6 0.8 3.0 0.8 4.0

t

PLHtPHL

Propagation Delay
Time LE to Qn

1.8 1.5 7.8 1.5 9.0
ns2.3 to 2.7 1.0 3.9 1.0 4.8

3.0 to 3.6 0.8 3.0 0.8 3.9

t

PZLtPZH

Output Enable Time 1.8 1.5 9.2 1.5 11.0

ns2.3 to 2.7 1.0 4.6 1.0 6.0

3.0 to 3.6 0.8 3.5 0.8 4.3

t

PLZtPHZ

Output Disable Time 1.8 1.5 6.8 1.5 7.2

ns2.3 to 2.7 1.0 3.8 1.0 4.5

3.0 to 3.6 0.8 3.5 0.8 4.1

t

s

Setup TIme, HIGH or
LOW level Dn to LE

1.8 2.5 2.5
ns2.3 to 2.7 1.5 1.5

3.0 to 3.6 1.5 1.5

t

h

Hold Time High or
LOW level Dn to LE

1.8 1.0 1.0
ns2.3 to 2.7 1.0 1.0

3.0 to 3.6 1.0 1.0

t

w

LE Pulse Width, HIGH 1.8 4.0 4.0

ns2.3 to 2.7 1.5 1.5

3.0 to 3.6 1.5 1.5

t

OSLHtOSHL

Output To Output
Skew Time (note1, 2)

1.8 0.75 0.75
ns2.3 to 2.7 0.5 0.5

3.0 to 3.6 0.5 0.5

74VCX16373

7/12

CAPACITIVE CHARACTERISTICS

1) CPDis defined as the value of the IC’s internal equivalent capacitance which is calculated from the operating current consumption without
load. (Refer to Test Circuit). Average operating current can be obtained by the following equation. I

CC(opr)=CPDxVCCxfIN+ICC

/16 (per

circuit)

TEST CIRCUIT

CL= 30 pF or equivalent (includes jig and probe capacitance)
R

L

=R1=500Ω or equivalent

R

T=ZOUT

of pulse generator (typically 50Ω)

WAVEFORM SYMBOL VALUES

Symbol Parameter

Test Condition Value

Unit

V

CC

(V)

T

A

=25°C

Min. Typ. Max.

C

IN

Input Capacitance

1.8, 2.5 or 3.3

VIN= 0 or V

CC

6pF

C

OUT

Output Capacitance

1.8, 2.5 or 3.3

VIN= 0 or V

CC

7pF

C

PD

Power Dissipation Capacitance
(note 1)

1.8, 2.5 or 3.3 fIN= 10MHz
V

IN

= 0 or V

CC

20 pF

TEST SWITCH

t

PLH,tPHL

Open

t

PZL,tPLZ(VCC

= 3.0 to 3.6V)

6V

t

PZL,tPLZ(VCC

= 2.3 to 2.7V or 1.8V) 2V

CC

t

PZH,tPHZ

GND

Symbol

V

CC

3.0 to3.6V 2.3 to 2.7V 1.8V

V

IH

2.7V

V

CC

V

CC

V

M

1.5V

V

CC

/2 VCC/2

V

X

VOL+ 0.3V VOL+ 0.15V VOL+ 0.15V

V

Y

VOH- 0.3V VOH- 0.15V VOH- 0.15V

74VCX16373

8/12

WAVEFORM 1 : LE TO Qn PROPAGATION DELAYS, LE MINIMUM PULSE WIDTH, Dn TO LE SETUP
AND HOLD TIMES (f=1MHz; 50% duty cycle)

WAVEFORM 2 : OUTPUT ENABL E AND DISABLE TIME (f=1MHz; 50% duty cycle)

74VCX16373

9/12

WAVEFORM 3 : PROPAGATION DEL AY TIME (f=1MHz; 50% duty cycle)

74VCX16373

10/12

DIM.

mm. inch

MIN. TYP MAX. MIN. TYP. MAX.

A 1.2 0.047

A1 0.05 0.15 0.002 0.006

A2 0.9 0.035

b 0.17 0.27 0.0067 0.011

c 0.09 0.20 0.0035 0.0079

D 12.4 12.6 0.488 0.496

E 8.1 BSC 0.318 BSC

E1 6.0 6.2 0.236 0. 244

e 0 .5 BSC 0.0197 BSC

K0˚ 8˚0˚ 8˚

L 0.50 0.75 0. 020 0.030

TSSOP48 MECHANICAL DATA

c

E

b

A2

A

E1

D

1

PIN 1 IDENTIFICATION

A1

L

K

e

7065588C

74VCX16373

11/12

DIM.

mm. inch

MIN. TYP MAX. MIN. TYP. MAX.

A 330 12.992
C 12.8 13.2 0.504 0.519
D 20.2 0.795
N 60 2.362

T 30.4 1.197

Ao 8.7 8.9 0.343 0.350
Bo 13.1 13.3 0.516 0.524
Ko 1.5 1.7 0.059 0.067
Po 3.9 4.1 0.153 0.161

P 11.9 12.1 0.468 0.476

Tape & Reel TSSOP48 MECHANICAL DATA

74VCX16373

12/12

Information furnished is believed to be accurate and reliable. However, STMicroelectronics assumes no responsibility for the
consequences of use o f suc h inf ormat ion n or f or an y infr ingeme nt of paten ts or oth er ri gh ts of third part ies whic h may resul t f rom
its use. No license is granted by implication or otherwise under any patent or patent rights of STMicroelectronics. Specifications
mentioned in this publication are subject to change without notice. This publication supersedes and replaces all information
previously supplied. STMicroelectronics products are not authorized for use as critical components in life support devices or
systems without express written approval of STMicroelectronics.

© The ST logo is a registered trademark of STMicroelectronics

© 2003 STMicroelectronics - Printed in Italy - All Rights Reserved

STMicroelectronics GROUP OF COMPANIES

Australia - Brazil - Canada - China - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan - Malaysia - Malta - Morocco

Singapore - Spain - Sweden - Switzerland - United Kingdom - United States.

© http://www.st.com