Datasheet 74LX1G132STR, 74LX1G132CTR Datasheet (SGS Thomson Microelectronics)

Page 1
1/11December 2002
5V TOLERANT INPUTS
HIGH SPEED:t
PD
= 5. 5ns (MAX.) at VCC=3V
I
CC
=1µA(MAX.)atTA=25°C
TYPICAL HYSTERESIS: V
h
=1V at VCC=4.5V
POWER DOWN PROTECTION ON INPUTS
AND OUTPUTS
SYMMETRICAL OUTPUT IMPEDANCE:
|I
OH
|=IOL= 24mA (MIN) at VCC=3V
BALANCED PROPAGATION DELAYS:
t
PLH
t
PHL
OPERATING VOLTAGE RANGE:
V
CC
(OPR) = 1.65V to 5.5V
(1.2V Data Retention)
IMPROVED LATCH-UP IMMUNITY
DESCRIPTION
The 74LX 1G132 is a low v oltage CMOS SINGLE 2-INPUT NAND GATE fabricated with s ub-micron silicon gate and double -layer metal wiring C
2
MOS technology. The internal circuit is composed of 3 stages including buffer output, which provide high noise immunity and stable output. Power down prot ec tion is provided on all inputs and 0 to 7V can be accepted on inputs with no
regard to the supply voltage. Th is device can be usedto interface5V to 3V. This together with its schmitt t rigger function allows it to be used on line receivers with slow rise/fall input signals. All inputs and outputs are equipped with protection circuits against static discharge.
74LX1G132
SINGLE 2-INPUT SCHMITT NAND GATE
PIN CONNECTION AND IEC LOGIC SYMBOLS
ORDER CODES
PACKAGE T & R
SOT23-5L 74LX1G132STR
SOT323-5L 74LX1G132CTR
SOT323-5LSOT23-5L
Page 2
74LX1G132
2/11
INPUT EQUIVALENT CIRCUIT
PIN DESCRIPTION TRUTH TABLE
ABSOLUTE MAXIMUM RATINGS
Absolute Maximum Ratings are those values beyond which damage to the device may occur. Functional operation under these conditions is not implied.
1) I
O
maximum rating must be observed
2) V
O
<GND,VO>V
CC
PIN No SYMBOL NAME AND FUNCTION
1 1A Data Input 2 1B Data Input 4 1Y Data Output 3 GND Ground (0V) 5
V
CC
Positive Supply Voltage
ABY
LLH
LHH HLH HHL
Symbol Parameter Value Unit
V
CC
Supply Voltage
-0.5 to +7.0 V
V
I
DC Input Voltage
-0.5 to +7.0 V
V
O
DC Output Voltage (VCC= 0V)
-0.5 to +7.0 V
V
O
DC Output Voltage (High or Low State) (note 1) -0.5 to VCC+ 0.5
V
I
IK
DC Input Diode Current
-50 mA
I
OK
DC Output Diode Current (note 2)
-50 mA
I
O
DC Output Current
± 50 mA
I
CC
or I
GND
DC VCCor Ground Current per Supply Pin
± 50 mA
T
stg
Storage Temperature
-65 to +150 °C
T
L
Lead Temperature (10 sec)
300 °C
Page 3
74LX1G132
3/11
RECOMMENDED OPERATING CONDITIONS
1) Truth Table guaranteed: 1.2V to 3.6V
Symbol Parameter Value Unit
V
CC
Supply Voltage (note 1)
1.65 to 5.5 V
V
I
Input Voltage
0 to 5.5 V
V
O
Output Voltage (VCC= 0V)
0 to 5.5 V
V
O
Output Voltage (High or Low State) 0 to V
CC
V
I
OH,IOL
High or Low Level Output Current (VCC= 4.5 to 5.5V)
± 32 mA
I
OH,IOL
High or Low Level Output Current (VCC= 3.0 to 3.6V)
± 24 mA
I
OH,IOL
High or Low Level Output Current (VCC= 2.7 to 3.0V)
± 12 mA
I
OH,IOL
High or Low Level Output Current (VCC= 2.3 to 2.7V)
± 8mA
I
OH,IOL
High or Low Level Output Current (VCC= 1.65 to 2.3V)
± 4mA
T
op
Operating Temperqture
-55 to 125 °C
Page 4
74LX1G132
4/11
DC SPECIFICATIONS
Symbol Parameter
Test Condition Value
Unit
V
CC
(V)
-40 to 85 °C -55 to 125 °C
Min. Max. Min. Max.
V
T+
Positive Input threshold
1.65 0.79 1.16 0.79 1.16
V
2.3 1.11 1.56 1.11 1.56 3 1.5 1.87 1.5 1.87
4.5 2.16 2.74 2.16 2.74
5.5 2.61 3.33 2.61 3.33
V
T-
Negative Input threshold
1.65 0.39 0.62 0.39 0.62
V
2.3 0.58 0.87 0.58 0.87 3 0.84 1.14 0.84 1.14
4.5 1.41 1.79 1.41 1.79
5.5 1.87 2.29 1.87 2.29
V
H
Hysteresis Voltage 1.65 0.37 0.62 0.37 0.62
V
2.3 0.48 0.77 0.48 0.77 3 0.56 0.87 0.56 0.87
4.5 0.71 1.04 0.71 1.04
5.5 0.71 1.11 0.71 1.11
V
OH
High Level Output Voltage
1.65 to 4.5
IO=-100 µAVCC-0.1 VCC-0.1
V
1.65
I
O
=-4 mA
1.2 1.2
2.3
I
O
=-8 mA
1.9 1.9
3.0
I
O
=-16 mA
2.4 2.4
I
O
=-24 mA
2.2 2.2
4.5
I
O
=-32 mA
3.8 3.8
V
OL
Low Level Output Voltage
1.65 to 4.5
I
O
=100 µA
0.1 0.1
V
1.65
I
O
=4 mA
0.45 0.45
2.3
I
O
=8 mA
0.3 0.3
3.0
I
O
=16 mA
0.4 0.4
I
O
=24 mA
0.55 0.55
4.5
I
O
=32 mA
0.55 0.55
I
I
Input Leakage Current
1.65 to 5.5
V
I
= 0 to 5.5V
± 10 ±10 µA
I
off
Power Off Leakage Current
0
V
I
or VO= 5.5V
10 10 µA
I
CC
Quiescent Supply Current
1.65 to 5.5
V
I=VCC
or GND
10 10 µA
Page 5
74LX1G132
5/11
AC ELECTRICAL CHARACTERISTICS (Input tr=tf=3ns)
CAPACITIVE CHARACTERISTICS
1) CPDis defined as the value of the IC’s internal equivalent capacitance which is calculated from the operating current consumption without load. (Refer to Test Circuit). Average operating current can be obtained by the following equation. I
CC(opr)=CPDxVCCxfIN+ICC
TEST CIRCUIT
RT=Z
OUT
of pulse generator (typically 50)
Symbol Parameter
Test Condition Value
Unit
V
CC
(V)
C
L
(pF)
R
L
()
t
s
= t
r
(ns)
-40 to 85 °C -55 to 125 °C
Min. Max. Min. Max.
t
PLHtPHL
Propagation Delay Time
1.65 to 1.95 15 1M 3.0
2 12.0 2 12.0
ns
2.3 to 2.7 2 7.0 2 7.0
3.0 to 3.6 1 6.0 1 6.0
4.5 to 5.5 1 5.5 1 5.5
1.65 to 1.95 30 1000 2.0 2 11.0 2 11.0
2.3 to 2.7 30 500 2.0 2 6.5 2 6.5
2.7 50 500 2.5 1 6.5 1 6.5
3.0 to 3.6 50 500 2.5 1 5.5 1 5.5
4.5 to 5.5 50 500 2.5 1 5.0 1 5.0
Symbol Parameter
Test Condition Value
Unit
V
CC
(V)
T
A
=25°C
Min. Typ. Max.
C
IN
Input Capacitance
05pF
C
PD
Power Dissipation Capacitance (note 1)
1.8 fIN= 10MHz 20 pF2.5 21
3.3 22
Page 6
74LX1G132
6/11
TEST CIRCUIT AND WAV EFOR M SYMBOL VALUE
WAVEFORM: PROPAGATION DELAY (f=1MHz; 50% duty cycle)
Symbol
V
CC
1.65 to 1.95V 2.3 to 2.7V 2.7 to 5.5V
C
L
15pF/30pF 15pF/30pF 15pF/50pF
R
L
1MΩ/1000 1MΩ/500 1MΩ/500
V
IH
V
CC
V
CC
V
CC
V
M
VCC/2 VCC/2 VCC/2
t
r=tr
<2.0ns <2.0ns <2.5ns
Page 7
74LX1G132
7/11
DIM.
mm. mils
MIN. TYP MAX. MIN. TYP. MAX.
A 0.90 1.45 35.4 57.1
A1 0.00 0.15 0.0 5.9
A2 0.90 1.30 35.4 51.2
b 0.35 0.50 13.7 19.7
C 0.09 0.20 3.5 7.8
D 2.80 3.00 110.2 118.1
E 2.60 3.00 102.3 118.1
E1 1.50 1.75 59.0 68.8
e.95 37.4
e1 1.9 74.8
L 0.35 0.55 13.7 21.6
SOT23-5L MECHANICAL DATA
0
Page 8
74LX1G132
8/11
DIM.
mm. mils
MIN. TYP MAX. MIN. TYP. MAX.
A 0.80 1.10 31.5 43.3
A1 0.00 0.10 0.0 3.9
A2 0.80 1.00 31.5 39.4
b 0.15 0.30 5.9 11.8
C 0.10 0.18 3.9 7.1
D 1.80 2.20 70.9 86.6
E 1.80 2.40 70.9 94.5
E1 1.15 1.35 45.3 53.1
e
.65
25.6
e1 1.3 51.2
L 0.10 0.30 3.9 11.8
SOT323-5L MECHANICAL DATA
0
Page 9
74LX1G132
9/11
DIM.
mm. inch
MIN. TYP MAX. MIN. TYP. MAX.
A 180 7.086 C 12.8 13.0 13.2 0.504 0.512 0.519 D 20.2 0.795 N 60 2.362
T 14.4 0.567
Ao 3.13 3.23 3.33 0.123 0.127 0.131 Bo 3.07 3.17 3.27 0.120 0.124 0.128 Ko 1.27 1.37 1.47 0.050 0.054 0.0.58 Po 3.9 4.0 4.1 0.153 0.157 0.161
P 3.9 4.0 4.1 0.153 0.157 0.161
Tape & Reel SOT23-xL MECHANICAL DATA
Page 10
74LX1G132
10/11
DIM.
mm. inch
MIN. TYP MAX. MIN. TYP. MAX.
A 175 180 185 6.889 7.086 7.283
C 12.8 13 13.2 0.504 0.512 0.519
D 20.2 0.795
N 59.5 60 60.5 2.362
T 14.4 0.567
Ao 2.25 0.088 Bo 2.7 0.106 Ko 1.2 0.047 Po 3.98 4 4.2 0.156 0.157 0.165
P 3.98 4 4.2 0.156 0.157 0.165
Tape & Reel SOT323-xL MECHANICAL DATA
Page 11
74LX1G132
11/11
Information furnished is believed to be accurate and reliable. However, STMicroelectronics assumes no responsibility f or t he consequences of use of such informatio n nor for any infringement of paten ts or o ther rig hts of t hird part ies which ma y result from its use. No license is granted by implication or otherwise under any patent or patent rights of STMicroelectronics. Specifications mentioned in this publication are subject to change without notice. This publication supersedes and replaces all information previousl y suppl ied. STM icroel ectronics produc ts are not auth orized for use as c ritica l compone nts in l ife s upport dev ices or systems without express written approval of STMicroelectronics.
© The ST logo is a registered trademark of STMicroelectronics
© 2002 STMicroelectronics - Printed in Italy - All Rights Reserved
STMicroelectronics GROUP OF COMPANIES
Australia - Brazil - Canada - China - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan - Malaysia - Malta - Morocco
Singapore - Spain - Sweden - Switzerland - United Kingdom - United States.
© http://www.st.com
Loading...