Datasheet 74LV4066U, 74LV4066PW, 74LV4066N, 74LV4066DB, 74LV4066D Datasheet (Philips)

 

74LV4066

Quad bilateral switches

Product specification Supersedes data of 1996 Jan 01 IC24 Data Handbook

1998 Jun 23

INTEGRATED CIRCUITS

Philips Semiconductors Product specification

74L V4066Quad bilateral switches

2

1998 Jun 23 853-2077 19619

FEA TURES

•Optimized for Low Voltage applications: 1.0V to 6.0V

•Accepts TTL input levels between V

CC

= 2.7 V and V

CC

= 3.6 V

•Typical V

OLP

(output ground bounce) < 0.8 V at VCC = 3.3 V,

T

amb

= 25 °C.

• Very low typ “ON” resistance:

25 at V

CC

– VEE = 4.5 V 35 at VCC – VEE = 3.0 V 60 at V

CC

– VEE = 2.0 V

•Output capability: non-standard

•I

CC

category: SSI

DESCRIPTION

The 74LV4066 is a low-voltage Si-gate CMOS device that is pin and function compatible with 74HC/HCT4066.

The 74LV4066 has four independent analog switches. Each switch has two input/output terminals (nY, nZ) and an active HIGH enable input (nE). When nE is LOW the corresponding analog switch is turned off.

The 74LV4066 has an on resistance which is dramatically reduced in comparison with 74HCT4066.

FUNCTION TABLE

INPUTS

nE

SWITCH

L off H on

NOTES:

H = HIGH voltage level L = LOW voltage level

QUICK REFERENCE DA TA

GND = 0 V; T

amb

= 25°C; tr =tf  2.5 ns

SYMBOL PARAMETER CONDITIONS TYPICAL UNIT

t

PZH/tPZL

Turn “ON” time: nE to V

OS

CL = 15pF

10 ns

t

PHZ/tPLZ

Turn “OFF” time: nE to V

OS

R

L

=

1K

VCC= 3.3V

13 ns

C

I

Input capacitance 3.5 pF

C

PD

Power dissipation capacitance per switch Notes 1, 2 11 pF

C

S

Maximum switch capacitances 8 pF

NOTES:

1. C

PD

is used to determine the dynamic power dissipation (PD in µW)

P

D

= CPD × V

CC

2

× fi  (CL × V

CC

2

× fo) where:

f

i

= input frequency in MHz; CL = output load capacity in pF;

f

o

= output frequency in MHz; Cs = maximum switch capacitance in pF;

 {(C

L

+ CS) × V

CC

2

× Fo} = sum of the outputs.

V

CC

= supply voltage in V .

2. The condition is V

I

= GND to V

CC.

ORDERING AND PACKAGE INFORMA TION

PACKAGES

TYPE NUMBER

PINS PACKAGE MATERIAL CODE

74LV4066N 16 DIL Plastic SOT27-1 74LV4066D 16 SO Plastic SOT108-1

74LV4066DB 16 SSOP Plastic SOT337-1

74LV4066PW 16 TSSOP Plastic SOT402-1

PIN CONFIGURATION

SV01669

12 11 10

9 8

7

6

5

4

3

2

1

13

14

GND

V

CC

1Y 1Z 2Z 2Y 2E 3E

1E 4E 4Y

4Z 3Z 3Y

PIN DESCRIPTION

NUMBER

SYMBOL FUNCTION

1, 4, 8, 11 1Y – 4Y Independent inputs/outputs 2, 3, 9, 10 1Z – 4Z Independent inputs/outputs

13, 5, 6, 12 1E to 4E Enable input (active HIGH)

7 GND Ground (0V)

14 V

CC

Positive supply voltage

Philips Semiconductors Product specification

74LV4066Quad bilateral switches

1998 Jun 23

3

FUNCTIONAL DIAGRAM

2

1Y 1Z 1E

1

13

3

2Y 2Z 2E

4

5

9

3Y 3Z 3E

8

6

10

4Y 4Z 4E

11 12

SV01670

IEC LOGIC SYMBOL

SV01671

1 13#

4 5# 8

11

6#

12#

2

3

9

10

1

13#

4 5#

8 6#

11 12#

2

3

9

10

1

X1

1

(a) (b)

SCHEMATIC DIAGRAM (ONE SWITCH)

SV01672

nE

GND nZ

nY

V

CC

V

CC

RECOMMENDED OPERA TING CONDITIONS

SYMBOL PARAMETER CONDITIONS MIN TYP MAX UNIT

V

CC

DC supply voltage See Note 1 1.0 3.3 6 V

V

I

Input voltage 0 – V

CC

V

O

Output voltage 0 – V

CC

V

T

amb

Operating ambient temperature range in free air

See DC and AC

characteristics

–40 –40

+85

+125

°C

tr, t

f

Input rise and fall times

VCC = 1.0V to 2.0V VCC = 2.0V to 2.7V VCC = 2.7V to 3.6V VCC = 3.6V to 5.5V

– – – –

500 200 100

50

ns/V

NOTE:

1. The LV is guaranteed to function down to V

CC

= 1.0V (input levels GND or VCC); DC characteristics are guaranteed from VCC = 1.2V to VCC = 5.5V.

ABSOLUTE MAXIMUM RATINGS

1, 2

In accordance with the Absolute Maximum Rating System (IEC 134). Voltages are referenced to GND (ground = 0 V).

SYMBOL PARAMETER CONDITIONS RATING UNIT

V

CC

DC supply voltage –0.5 to +7.0 V

I

IK

DC input diode current VI < –0.5 or VI > VCC + 0.5V 20 mA

I

OK

DC output diode current VO < –0.5 or VO > VCC + 0.5V 50 mA

I

O

DC switch current –0.5V < VO < VCC + 0.5V 25 mA

T

stg

Storage temperature range –65 to +150 °C

P

TOT

Power dissipation per package – plastic DIL – plastic mini-pack (SO) – plastic shrink mini-pack (SSOP and TSSOP)

for temperature range: –40 to +125°C above +70°C derate linearly with 12 mW/K above +70°C derate linearly with 8 mW/K above +60°C derate linearly with 5.5 mW/K

750 500 400

mW

NOTES:

1. Stresses beyond those listed may cause permanent damage to the device. These are stress ratings only and functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability .

2. The input and output voltage ratings may be exceeded if the input and output current ratings are observed.

Philips Semiconductors Product specification

74LV4066Quad bilateral switches

1998 Jun 23

4

DC ELECTRICAL CHARACTERISTICS

Over recommended operating conditions. V oltages are referenced to GND (ground = 0 V).

LIMITS

SYMBOL PARAMETER TEST CONDITIONS

-40°C to +85°C -40°C to +125°C

UNIT

MIN TYP

1

MAX MIN MAX

VCC = 1.2 V 0.90 0.90 VCC = 2.0 V 1.40 1.4

V

IH

HIGH l

evel Inpu

t

VCC = 2.7 to 3.6 V 2.00 2.0

V

voltage

VCC = 4.5 V 3.15 3.15 VCC = 6.0 V 4.20 4.20 VCC = 1.2 V 0.30 0.30 VCC = 2.0 V 0.60 0.60

V

IL

LOW l

evel Inpu

t

VCC = 2.7 to 3.6 V 0.80 0.80

V

voltage

VCC = 4.5 V 1.35 1.35 VCC = 6.0 V 1.80 1.80

±I

I

Input leakage current

VCC = 3.6 V; VI = VCC or GND VCC = 6.0 V; VI = VCC or GND

1.0

2.0

1.0

2.0

µA

±I

S

Analog switch OFF-state current per channel

VCC = 3.6 V; VI = VIH or V

IL

VCC = 6.0 V; VI = VIH or V

IL

1.0

2.0

1.0

2.0

µA

±I

S

Analog switch ON-state current per channel

VCC = 3.6 V; VI = VIH or V

IL

VCC = 6.0 V; VI = VIH or V

IL

1.0

2.0

1.0

2.0

µA

I

CC

Quiescent supply current

VCC = 3.6V; VI = VCC or GND; IO = 0 VCC = 6.0V; VI = VCC or GND; IO = 0

20 40

40 80

µA

∆I

CC

Additional quiescent supply current per input

VCC = 2.7 V to 3.6 V; VI = VCC – 0.6 V 500 850 µA

R

ON

ON-resistance (peak)

VCC = 1.2 V; VI = VIH or V

IL

VCC = 2.0 V; VI = VIH or V

IL

VCC = 2.7 V; VI = VIH or V

IL

VCC = 3.0 to 3.6 V; VI = VIH or V

IL

VCC = 4.5 V; VI = VIH or V

IL

VCC = 6.0 V; VI = VIH or V

IL

300

60 41 37 25 23

–

130

60 72 52 47

–

150

90 83 60 54

Ω

R

ON

ON-resistance (rail)

VCC = 1.2 V; VI = VIH or V

IL

VCC = 2.0 V; VI = VIH or V

IL

VCC = 2.7 V; VI = VIH or V

IL

VCC = 3.0 to 3.6 V; VI = VIH or V

IL

VCC = 4.5 V; VI = VIH or V

IL

VCC = 6.0 V; VI = VIH or V

IL

75 35 26 24 15 13

– 98 60 52 40 35

–

115

68 60 45 40

Ω

R

ON

ON-resistance (rail)

VCC = 1.2 V; VI = VIH or V

IL

VCC = 2.0 V; VI = VIH or V

IL

VCC = 2.7 V; VI = VIH or V

IL

VCC = 3.0 to 3.6 V; VI = VIH or V

IL

VCC = 4.5 V; VI = VIH or V

IL

VCC = 6.0 V; VI = VIH or V

IL

75 40 35 30 22 20

–

110

72 65 47 40

–

130

85 75 55 47

Ω

∆R

ON

Maximum variation of ON-resistance between any two channels

VCC = 1.2 V; VI = VIH or V

IL

VCC = 2.0 V; VI = VIH or V

IL

VCC = 2.7 V; VI = VIH or V

IL

VCC = 3.0 to 3.6 V; VI = VIH or V

IL

VCC = 4.5 V; VI = VIH or V

IL

VCC = 6.0 V; VI = VIH or V

IL

– 5 4 4 3 2

Ω

NOTE:

1. All typical values are measured at T

amb

= 25°C.

2. At supply voltage approaching 1.2V , the analog switch ON-resistance becomes extremely non-linear. Therefore it is recommended that these devices be used to transmit digital signals only, when using these supply voltages.

Philips Semiconductors Product specification

74LV4066Quad bilateral switches

1998 Jun 23

5

V

HIGH

(from enable inputs)

I

is

nZ

GND

nY

V

is

= 0 to VCC – GND

SV01673

Figure 1. Test circuit for measuring ON-resistance (R

on).

A

LOW

(from enable inputs)

nZ

GND

nY

V

I

= VCC or GND VO = GND or V

CC

A

SV01674

Figure 2. Test circuit for measuring OFF-state current.

A

HIGH

(from enable inputs)

nZ

GND

nY

V

I

= V CC or GND VO (open circuit)

A

SV01675

Figure 3. Test circuit for measuring ON-state current.

0

VCC= 2.0 V

V

CC

= 3.0 V

V

CC

= 4.5 V

0 1.2 2.4 3.6

V

is

(V)

4.8

20

40

60

R

ON

()

SV01676

Figure 4. Typical ON-resistance (RON) as a function of input

voltage (V

is

) for Vis = 0 to VCC – VEE.

AC CHARACTERISTICS

GND = 0 V; tr = tf ≤ 2.5ns; CL = 50pF

LIMITS

SYMBOL PARAMETER

–40 to +85 °C –40 to +125 °C

UNIT

CONDITION

MIN TYP1MAX MIN MAX VCC(V) OTHER

8 1.2

p

5 26 31 2.0

RL = ∞;

t

PHL/tPLH

Propagation dela

y

V

to V

3

2

15 18

ns

2.7 to 3.6

L

CL = 50 pF

V

is

to

V

os

2 13 15 4.5

Fi

gure

12

2 10 12 6.0 40 1.2 22 43 51 2.0

R

= 1 k;

t

PZH/tPZL

Turn-on time

12

2

25 30 ns 2.7 to 3.6

L

CL = 50 pF

nE to V

os

10 21 26 4.5

Fi

gures 13 and 14

8 16 20 6.0 50 1.2 27 65 81 2.0

RL = 1 k;

t

PHZ/tPLZ

Turn-off time

15

2

38 47 ns 2.7 to 3.6

L

CL = 50 pF

nE to V

os

13 32 40 4.5

Fi

gures 13 and 14

12 28 34 6.0

NOTES:

1. All typical values are measured at T

amb

= 25°C.

2. All typical values are measured at V

CC

= 3.3V .

Philips Semiconductors Product specification

74LV4066Quad bilateral switches

1998 Jun 23

6

ADDITIONAL AC CHARACTERISTICS

GND = 0 V; tr = tf ≤ 2.5ns; CL = 50pF

SYMBOL

PARAMETER TYP UNIT

V

CC

(V)

V

IS(P–P)

(V)

CONDITIONS

0.04

3.0 2.75

RL = 10 kW; CL = 50 pF

Sine-wave distortion f

= 1

kHz

0.02

%

6.0 5.50

L L

Figure 15

0.12

3.0 2.75

RL = 10 kW; CL = 50 pF

Sine-wave distortion f

= 10

kHz

0.06

%

6.0 5.50

L L

Figure 15

“

”

–50

3.0 Note 1

RL = 600 kW; CL = 50 pF; f=1 MHz

Switch OFF signal feed through

–50

dB

6.0

L L

Figures 10 and 16

–60

3.0 Note 1

RL = 600 kW; CL = 50 pF; f=1 MHz

Crosstalk between any two switches

–60

dB

6.0

L L

Figure 12

Crosstalk voltage between enable or address

110

3.0

RL = 600 kW; CL = 50 pF; f=1 MHz

V

(p–p)

g

input to any switch (peak-to-peak value)

220

mV

6.0

(nE, square wave between V

CC

and

GND, Tr = tf = 6 ns) Figure 13

p

180

3.0 Note 2

RL = 50 kW; CL = 50 pF

f

max

Minimum frequency res onse (–3 dB)

200

mHz

6.0

L L

Figures 11 and 14

C

S

Maximum switch capacitance 8 pF

GENERAL NOTES:

V

is

is the input voltage at nY or nZ terminal, whichever is assigned as an input.

V

os

is the output voltage at nY or nZ terminal, whichever is assigned as an output.

NOTES:

1. Adjust input voltage V

is

is 0 dBm level (0 dBm = 1 mW into 600 W).

2. Adjust input voltage V

is

is 0 dBm level at Vos for 1 MHz (0 dBm = 1 mW into 50 W).

(dB)

f (kHz)

0

10 10

2

10

3

10

4

10

5

10

6

–50

–100

SV01677

Figure 5. Typical switch “OFF” signal feed-through as a

function of frequency.

(dB)

f (kHz)

5

10 10

2

10

3

10

4

10

5

10

6

0

–5

SV01678

Figure 6. Typical frequency response.

NOTES TO FIGURES 5 AND 6:

Test conditions: V

CC

= 3.0 V; GND = 0 V; RL = 50 W; R

SOURCE

= 1kW.

GND

2R

L

V

CC

channel

ON

V

is

0.1 mF

R

L

nY/nZ nZ/nY

2R

L

C

L

GND

2R

L

2R

L

V

CC

V

CC

channel

OFF

(b)(a)

nY/nZ nZ/nY

2R

L

R

L

V

os

C

L

dB

SV01679

Figure 7. Test circuit for measuring crosstalk between any two switches.

(a) channel ON condition; (b) channel OFF condition.

Philips Semiconductors Product specification

74LV4066Quad bilateral switches

1998 Jun 23

7

GND

2R

L

2R

L

V

CC

V

CC

GND

V

CC

nE

nY/nZ nZ/nY

2R

L

2R

L

C

L

oscilloscope

DUT

SV01681

Figure 8. Test circuit for measuring

crosstalk between control and any switch.

NOTE TO FIGURE 8:

The crosstalk is defined as follows (oscilloscope output):

V

(p–p)

SV01680

GND

2R

L

V

CC

channel

ON

V

is

Vos

sine–wave

0.1 mF nY/nZ nZ/nY

2RLC

L

dB

SV01682

Figure 9. Test circuit for measuring

minimum frequency response.

NOTE TO FIGURE 9:

Adjust input voltage to obtain 0 dBm at V

OS

when Fin = 1 MHz . A f t e r

set-up frequency of f

in

is increased to obtain a reading of –3 dB at V

OS.

GND

2R

L

V

CC

channel

ON

V

is

V

os

fin = 1 kHz sine–wave

10 mF

nY/nZ nZ/nY

2RLC

L

distortion meter

SV01683

Figure 10. Test circuit for measuring sine-wave distortion.

GND

2R

L

V

CC

channel

OFF

V

is

V

os

0.1 mF nY/nZ

nZ/nY

2R

L

C

L

dB

SV01684

Figure 11. Test circuit for measuring

switch “OFF” signal feed-through.

Philips Semiconductors Product specification

74LV4066Quad bilateral switches

1998 Jun 23

8

WAVEFORMS

VM = 1.5 V at V

CC

≥ 2.7 V

V

M

= 0.5 × VCC at VCC ≤ 2.7 V

V

OL

and VOH are the typical output voltage drop that occur with the output load V

X

= VOL + 0.3 V at VCC ≥ 2.7 V

V

X

= VOL + 0.1 × VCC at VCC < 2.7 V

V

Y

= VOH – 0.3 V at VCC ≥ 2.7 V

V

Y

= VOH – 0.1 × VCC VCC < 2.7 V

SV01685

V

is

V

os

t

PHL

t

PLH

V

M

V

M

V

I

GND

V

OL

V

OH

Figure 12. Input (Vis) to output (Vos) propagation delays.

outputs

disabled

outputs

enabled

outputs enabled

t

PHZ

t

PZH

t

PZL

t

PLZ

V

X

V

Y

V

M

V

M

V

M

nE INPUT

OUTPUT LOW-to-OFF OFF-to-LOW

OUTPUT

HIGH-to-OFF OFF-to-HIGH

V

OL

GND

V

OH

V

CC

V

I

SV01686

Figure 13. Turn-on and turn-off times

for the inputs (nS, E

) to the output (Vos).

TEST CIRCUIT

V

M

V

M

t

W

NEGATIVE PULSE

10% 10%

90%

0V

V

M

V

M

t

W

V

I

POSITIVE PULSE

90% 90%

10%

0V

t

THL

(t

f

)

t

TLH

(tr)t

THL

(tf)

t

TLH

(tr)

VM = 1.5V

Input Pulse Definition

SY00044

SWITCH POSITION

PULSE

GENERATOR

R

T

V

l

D.U.T.

V

O

CL= 50pF

R

L

= 1k

V

cc

Test Circuit for Outputs

Open GND

S

1

V

S1

DEFINITIONS

V

CC

V

I

< 2.7V

2.7–3.6V

V

CC

2.7V

TEST S

1

t

PLZ/tPZL

t

PLH/tPHL

t

PHZ/tPZH

V

S1

Open

GND

V

S1

≥ 4.5 V

2  V

CC

V

CC

2  V

CC

RL = Load resistor C

L

= Load capacitance includes jig and probe capacitance

R

T

= Termination resistance should be equal to Z

OUT

of

pulse generators.

V

I

2  V

CC

RL = 1k

Figure 14. Load circuitry for switching times.

Philips Semiconductors Product specification

74LV4066Quad bilateral switches

yyyy mmm dd

9

Philips Semiconductors and Philips Electronics North America Corporation reserve the right to make changes, without notice, in the products, including circuits, standard cells, and/or software, described or contained herein in order to improve design and/or performance. Philips Semiconductors assumes no responsibility or liability for the use of any of these products, conveys no license or title under any patent, copyright, or mask work right to these products, and makes no representations or warranties that these products are free from patent, copyright, or mask work right infringement, unless otherwise specified. Applications that are described herein for any of these products are for illustrative purposes only. Philips Semiconductors makes no representation or warranty that such applications will be suitable for the specified use without further testing or modification.

LIFE SUPPORT APPLICA TIONS Philips Semiconductors and Philips Electronics North America Corporation Products are not designed for use in life support appliances, devices, or systems where malfunction of a Philips Semiconductors and Philips Electronics North America Corporation Product can reasonably be expected to result in a personal injury. Philips Semiconductors and Philips Electronics North America Corporation customers using or selling Philips Semiconductors and Philips Electronics North America Corporation Products for use in such applications do so at their own risk and agree to fully indemnify Philips Semiconductors and Philips Electronics North America Corporation for any damages resulting from such improper use or sale.

This data sheet contains preliminary data, and supplementary data will be published at a later date. Philips Semiconductors reserves the right to make changes at any time without notice in order to improve design and supply the best possible product.

Philips Semiconductors 811 East Arques Avenue P.O. Box 3409 Sunnyvale, California 94088–3409 Telephone 800-234-7381

DEFINITIONS

Data Sheet Identification Product Status Definition

Objective Specification

Preliminary Specification

Product Specification

Formative or in Design

Preproduction Product

Full Production

This data sheet contains the design target or goal specifications for product development. Specifications may change in any manner without notice.

This data sheet contains Final Specifications. Philips Semiconductors reserves the right to make changes at any time without notice, in order to improve design and supply the best possible product.

Philips Semiconductors and Philips Electronics North America Corporation

register eligible circuits under the Semiconductor Chip Protection Act.

 Copyright Philips Electronics North America Corporation 1998

print code Date of release: 05-96 Document order number:

 

Philips Semiconductors Product specification

74LV4066Quad bilateral switches

yyyy mmm dd

10

Philips Semiconductors and Philips Electronics North America Corporation reserve the right to make changes, without notice, in the products, including circuits, standard cells, and/or software, described or contained herein in order to improve design and/or performance. Philips Semiconductors assumes no responsibility or liability for the use of any of these products, conveys no license or title under any patent, copyright, or mask work right to these products, and makes no representations or warranties that these products are free from patent, copyright, or mask work right infringement, unless otherwise specified. Applications that are described herein for any of these products are for illustrative purposes only. Philips Semiconductors makes no representation or warranty that such applications will be suitable for the specified use without further testing or modification.

LIFE SUPPORT APPLICA TIONS Philips Semiconductors and Philips Electronics North America Corporation Products are not designed for use in life support appliances, devices, or systems where malfunction of a Philips Semiconductors and Philips Electronics North America Corporation Product can reasonably be expected to result in a personal injury. Philips Semiconductors and Philips Electronics North America Corporation customers using or selling Philips Semiconductors and Philips Electronics North America Corporation Products for use in such applications do so at their own risk and agree to fully indemnify Philips Semiconductors and Philips Electronics North America Corporation for any damages resulting from such improper use or sale.

This data sheet contains preliminary data, and supplementary data will be published at a later date. Philips Semiconductors reserves the right to make changes at any time without notice in order to improve design and supply the best possible product.

Philips Semiconductors 811 East Arques Avenue P.O. Box 3409 Sunnyvale, California 94088–3409 Telephone 800-234-7381

DEFINITIONS

Data Sheet Identification Product Status Definition

Objective Specification

Preliminary Specification

Product Specification

Formative or in Design

Preproduction Product

Full Production

This data sheet contains the design target or goal specifications for product development. Specifications may change in any manner without notice.

This data sheet contains Final Specifications. Philips Semiconductors reserves the right to make changes at any time without notice, in order to improve design and supply the best possible product.

Philips Semiconductors and Philips Electronics North America Corporation

register eligible circuits under the Semiconductor Chip Protection Act.

 Copyright Philips Electronics North America Corporation 1998

print code Date of release: 05-96 Document order number: 9397-750-04659

 