Datasheet 74F157, 74F158 Datasheet (Philips)

查询74F157供应商

INTEGRATED CIRCUITS

74F157*, 74F157A, 74F158*, 74F158A Data selectors/multiplexers

* Discontinued part. Please see the Discontinued Product List in Section 1, page 21.

Product specification 1996 Mar 12 IC15 Data Handbook

 

Philips Semiconductors Product specification

74F157A, 74F158AData selectors/multiplexers

74F157A: Quad 2-input data selector/multiplexer, non-inverting 74F158A: Quad 2-input data selector/multiplexer, inverting

DESCRIPTION

The 74F157A is a high speed Quad 2-Input Multiplexer which selects 4 bits of data from one of two sources under the control of a common Select input (S). The Enable input (E When E

is High, all of the outputs (Yn) are forced Low regardless of

) is active when Low.

all other input conditions. Moving data from two registers to a common output bus is a

common use of the 74F157A. The state of the Select input determines the particular register from which the data comes.

The device is the logic implementation of a 4-pole, 2-position switch where the position of the switch is determined by the logic levels supplied to the Select input.

The 74F158A is similar, but has inverting outputs (Y

n).

ORDERING INFORMATION

ORDER CODE

DESCRIPTION

16-pin plastic DIP N74F157AN, N174F158AN I74F157AN SOT38-4 16-pin plastic SO N74F157AD, N74F158AD I74F157AD SOT109-1

COMMERCIAL RANGE

VCC = 5V ±10%, T

= 0°C to +70°C

amb

•Industrial temperature range (–10°C to +85°C) available for

74F157A

TYPICAL

TYPE

PROPAGATION

DELA Y

74F157 4.6ns 15mA

74F157A 4.6ns 15mA

74F158 3.7ns 10mA

74F158A 3.7ns 10mA

INDUSTRIAL RANGE

VCC = 5V ±10%, T

= –40°C to +85°C

amb

TYPICAL

SUPPLY CURRENT

(TOTAL)

PKG. DWG. #

INPUT AND OUTPUT LOADING AND FAN OUT TABLE

PINS DESCRIPTION 74F (U.L.) HIGH/LOW LOAD VALUE HIGH/LOW

Ina, Inb, Inc, Ind Data inputs 1.0/1.0 20µA/0.6mA

S Select input 1.0/1.0 20µA/0.6mA

E Enable input 1.0/1.0 20µA/0.6mA Ya–Yd Data outputs (74F157/74F157A) 50/33 1.0mA/20mA Ya–Yd Data outputs (74F158/74F158A) 50/33 1.0mA/20mA

NOTE: One (1.0) FAST unit load is defined as: 20µA in the High state and 0.6mA in the Low state.

PIN CONFIGURATIONS, 74F157A 74F158A

I0a I1a

I0b I1b

S I0a I1a

I0b I1b

1 2 3

Y

a

4 5 6

b

Y

1

S

2 3 4

Ya

5 6

Yb

16 15 14 13 12 11 107

98GND Yc

SF00215

V E I0d

I1d Yd I0c I1c

CC

16 15 14 13 12 11 107

98GND Yc

SF00216

LOGIC SYMBOLS, 74F157A 74F158A

2356111014

13

2356111014

V E

I0d I1d Yd I0c I1c

CC

13

I0a I1a I0b I1b I0c I1c I0d

1

15

VCC = Pin 16 GND = Pin 8

S E

Ya Yb Yc Yd

47912

1996 Mar 12 853-0346 16555

I1d

SF00217

2

1

15

VCC = Pin 16 GND = Pin 8

I0a I1a I0b I1b I0c I1c I0d S E

Ya Yb Yc Yd

47912

I1d

SF00218

Philips Semiconductors Product specification

74F157A, 74F158AData selectors/multiplexers

IEEE/IEC SYMBOLS, 74F157A 74F158A

1 15

2 3

5 6

11 10

14 13

G1 EN

1 1

MUX

SF00219

LOGIC DIAGRAM, 74F157A

I0a I1a I0b I1b I0c I1c I0d I1d E S

2 3 5 6 11 10 14 13 15 1

1 15

4

7

9

12

2 3

5 6

11 10

14 13

G1 EN

1 1

MUX

4

7

9

12

SF00220

74F158A

I0a I1a I0b I1b I0c I1c I0d I1d E S

2 3 5 6 11 10 14 13 15 1

47912

Ya Yb Yc Yd

= Pin 16

V

CC

GND = Pin 8

FUNCTION TABLE, 74F157A

INPUTS OUTPUT

E S I0n I1n Yn

H X X X L

L H X L L L H X H H L L L X L L L H X H

H = High voltage level L = Low voltage level X = Don’t care

1996 Mar 12

SF00225

47912

Ya Yb Yc Yd

= Pin 16

V

CC

GND = Pin 8

74F158A

INPUTS OUTPUT

E S I0n I1n Yn

H X X X H L L L X H L L H X L L H X L H L H X H L

H = High voltage level L = Low voltage level X = Don’t care

3

SF00226

Philips Semiconductors Product specification

T

O erating free-air tem erature range

°C

SYMBOL

PARAMETER

UNIT

T

Operating free air temperature range

1

SYMBOL

PARAMETER

TEST CONDITIONS

1

UNIT

VOHHigh-level out ut voltage

V

VOLLow-level out ut voltage

V

4

ICCSu ly current (total)

4

V

MAX

74F157A, 74F158AData selectors/multiplexers

ABSOLUTE MAXIMUM RATINGS

(Operation beyond the limit set forth in this table may impair the useful life of the device. Unless otherwise noted these limits are over the operating free-air temperature range.)

SYMBOL

V V I

IN

V I

OUT

T

CC IN

OUT

amb

stg

Supply voltage –0.5 to +7.0 V Input voltage –0.5 to +7.0 V Input current –30 to +5 mA Voltage applied to output in High output state –0.5 to V Current applied to output in Low output state 40 mA

p

Storage temperature range –65 to +150 °C

RECOMMENDED OPERATING CONDITIONS

V V V I I I

CC IH

IL IK OH OL

amb

Supply voltage 4.5 5.0 5.5 V High-level input voltage 2.0 V Low-level input voltage 0.8 V Input clamp current –18 mA High-level output current –1 mA Low-level output current 20 mA

p

PARAMETER RATING UNIT

CC

Commercial Range 0 to +70

Industrial Range 74F157A only –40 to +85

V

°

LIMITS

MIN NOM MAX

Commercial Range 0 70

Industrial Range 74F157A only –40 85 °C

DC ELECTRICAL CHARACTERISTICS

(Over recommended operating free-air temperature range unless otherwise noted.)

LIMITS

MIN TYP

p

V

IK

I

IH

I

IL

I

OS

Input clamp voltage VCC = MIN, II = I Input current at maximum input voltage VCC = MAX, VI = 7.0V 100 µA High-level input current VCC = MAX, VI = 2.7V 20 µA Low-level input current VCC = MAX, VI = 0.5V –0.6 mA Short-circuit output current

pp

3

74F157A 74F158A

VCC = MIN, VIL = MAX ±10%V VIH = MIN, IOH = MAX ±5%V

CC

VCC = MIN, VIL = MAX ±10%V VIH = MIN, IOL = MAX ±5%V

IK

CC

VCC = MAX –60 –150 mA

=

CC

2.5

2.7 3.4

NOTES:

1. For conditions shown as MIN or MAX, use the appropriate value specified under recommended operating conditions for the applicable type.

2. All typical values are at V

3. Not more than one output should be shorted at a time. For testing I

= 5V, T

CC

techniques are preferable in order to minimize internal heating and more accurately reflect operational values. Otherwise, prolonged shorting

amb

= 25°C.

, the use of high-speed test apparatus and/or sample-and-hold

OS

of a High output may raise the chip temperature well above normal and thereby cause invalid readings in other parameter tests. In any sequence of parameter tests, I

is measured with 4.5V applied to all inputs and all outputs open.

4. I

CC

tests should be performed last.

OS

2

MAX

0.30 0.50

–0.73 –1.2 V

15.0 23.0 mA

14.0 19.0 mA

1996 Mar 12

4

Philips Semiconductors Product specification

74F157A, 74F158AData selectors/multiplexers

AC ELECTRICAL CHARACTERISTICS FOR 74F157A AND 74F158A

LIMITS

SYMBOL PARAMETER

t

PLH

t

PHL

t

PLH

t

PHL

t

PLH

t

PHL

t

PLH

t

PHL

t

PLH

t

PHL

t

PLH

t

PHL

Propagation delay I0n, I1n to Yn

Propagation delay E to Yn

Propagation delay S to Yn

Propagation delay I0n, I1n to Yn

Propagation delay E to Yn

Propagation delay S to Yn

74F157A

74F158A

TEST

CONDITION

Waveform 1

Waveform 3

Waveform 1

Waveform 2

Waveform 4

Waveform 2

VCC = +5.0V

T

= +25°C

amb

C

= 50pF

L

= 500Ω

R

L

MIN TYP MAX MIN MAX MIN MAX

3.5

4.5

2.5

3.5

6.0

7.5

4.0

5.0

5.5

7.5

4.5

6.0

3.0

4.0

1.5

2.5

4.5

5.5

5.0

6.0

4.5

6.5

4.0

5.5

VCC = +5.0V ± 10%

T

amb

6.5

5.0

9.0

6.5

10.0

7.5

6.0

4.0

7.0

7.5

8.5

7.5

= 0°C to +70°C

C

= 50pF

L

= 500Ω

R

L

3.0

1.5

5.5

4.0

5.0

4.0

2.5

1.0

4.0

5.0

4.0

3.5

7.0

6.0

10.5

7.0

11.0

8.5

7.0

4.5

7.5

8.0

9.5

8.0

VCC = +5.0V ± 10%

T

= –40°C to +85°C

amb

C

= 50pF

L

= 500Ω

R

L

3.0

1.5

5.5

4.0

5.0

4.0

7.5

6.5

11.0

7.5

11.5

9.0

— — ns

UNIT

ns

AC WAVEFORMS

For all waveforms, VM = 1.5V

I0n, I1n, S

Yn

Waveform 1. Propagation Delay for Data and Select to Output

E

Yn

Waveform 3. Propagation Delay for Enable to Output

V

M

t

PHL

M

t

PLH

V

M

t

PLH

V

M

V

M

t

PHL

V

M

V

M

SF00221

V

M

SF00223

I0n, I1n, S

Yn

V

M

t

PLH

V

M

t

PHL

V

M

V

M

SF00222

Waveform 2. Propagation Delay for Data and Select to Output

E

Yn

V

M

t

PHL

V

M

t

PLH

V

M

V

M

SF00224

Waveform 4. Propagation Delay for Enable to Output

1996 Mar 12

5

Philips Semiconductors Product specification

74F157A, 74F158AData selectors/multiplexers

TEST CIRCUIT AND WAVEFORMS

V

CC

PULSE

GENERATOR

V

IN

R

T

D.U.T.

V

OUT

R

C

L

Test Circuit for Totem-Pole Outputs

DEFINITIONS:

= Load resistor;

R

L

see AC ELECTRICAL CHARACTERISTICS for value.

= Load capacitance includes jig and probe capacitance;

C

L

see AC ELECTRICAL CHARACTERISTICS for value.

R

= Termination resistance should be equal to Z

T

pulse generators.

OUT

of

NEGATIVE PULSE

POSITIVE PULSE

family

74F

90%

10%

amplitude

t

w

V

M

10%

)

V

90%

M

t

THL (tf

t

TLH (tr

)

t

TLH (tr

t

THL (tf

t

w

Input Pulse Definition

INPUT PULSE REQUIREMENTS

V

rep. rate

M

3.0V

1.5V

1MHz 500ns

10%

)

90%

t

w

V

M

V

M

90%

10%

t

TLHtTHL

2.5ns 2.5ns

AMP (V)

0V

AMP (V)

0V

SF00006

1996 Mar 12

6

Philips Semiconductors Product specification

Data selectors/multiplexers

74F157*, 74F157A 74F158*, 74F158A

DIP16: plastic dual in-line package; 16 leads (300 mil) SOT38-4

* Discontinued part. Please see the Discontinued Product List in Section 1, page 21.

1996 Mar 12

7

Philips Semiconductors Product specification

Data selectors/multiplexers

74F157*, 74F157A 74F158*, 74F158A

SO16: plastic small outline package; 16 leads; body width 3.9 mm SOT109-1

* Discontinued part. Please see the Discontinued Product List in Section 1, page 21.

1996 Mar 12

8

Philips Semiconductors Product specification

Data selectors/multiplexers

74F157*, 74F157A 74F158*, 74F158A

NOTES

* Discontinued part. Please see the Discontinued Product List in Section 1, page 21.

1996 Mar 12

9

Philips Semiconductors Product specification

Data selectors/multiplexers

Data sheet status

Objective specification

Preliminary specification

Product specification

Product status

Development

Qualification

Production

Definition

This data sheet contains the design target or goal specifications for product development. Specification may change in any manner without notice.

This data sheet contains preliminary data, and supplementary data will be published at a later date. Philips Semiconductors reserves the right to make chages at any time without notice in order to improve design and supply the best possible product.

This data sheet contains final specifications. Philips Semiconductors reserves the right to make changes at any time without notice in order to improve design and supply the best possible product.

74F157*, 74F157A,

74F158

[1]

*, 74F158A

[1] Please consult the most recently issued datasheet before initiating or completing a design.

Definitions

Short-form specification — The data in a short-form specification is extracted from a full data sheet with the same type number and title. For

detailed information see the relevant data sheet or data handbook. Limiting values definition — Limiting values given are in accordance with the Absolute Maximum Rating System (IEC 134). Stress above one

or more of the limiting values may cause permanent damage to the device. These are stress ratings only and operation of the device at these or at any other conditions above those given in the Characteristics sections of the specification is not implied. Exposure to limiting values for extended periods may affect device reliability.

Application information — Applications that are described herein for any of these products are for illustrative purposes only. Philips Semiconductors make no representation or warranty that such applications will be suitable for the specified use without further testing or modification.

Disclaimers

Life support — These products are not designed for use in life support appliances, devices or systems where malfunction of these products can

reasonably be expected to result in personal injury . Philips Semiconductors customers using or selling these products for use in such applications do so at their own risk and agree to fully indemnify Philips Semiconductors for any damages resulting from such application.

Right to make changes — Philips Semiconductors reserves the right to make changes, without notice, in the products, including circuits, standard cells, and/or software, described or contained herein in order to improve design and/or performance. Philips Semiconductors assumes no responsibility or liability for the use of any of these products, conveys no license or title under any patent, copyright, or mask work right to these products, and makes no representations or warranties that these products are free from patent, copyright, or mask work right infringement, unless otherwise specified.

Philips Semiconductors 811 East Arques Avenue P.O. Box 3409 Sunnyvale, California 94088–3409 Telephone 800-234-7381

* Discontinued part. Please see the Discontinued Product List in Section 1, page 21.

 Copyright Philips Electronics North America Corporation 1998

print code Date of release: 10-98 Document order number: 9397-750-05083

 

yyyy mmm dd

10