Page 1
INTEGRATED CIRCUITS
74ALS175
Quad D flip–flop
Product specification
IC05 Data Handbook
1991 Feb 08
Page 2
Philips Semiconductors Product specification
74ALS175Quad D flip-flop
FEA TURES
•Four edge-triggered D flip-flops
•Buffered common clock
•Buffered asynchronous master reset
•True and complementary outputs
DESCRIPTION
The 74ALS175 is a quad, edge-triggered D-type flip-flops with
individual D inputs and both Q and Q
clock (CP) and master reset (MR
flip-flops simultaneously.
The register is fully edge-triggered. The state of each D input, one
setup time before the Low-to-High clock transition is transferred to
the corresponding flip-flop’s Q output.
All Q outputs will be forced Low independent of clock or data inputs
by a Low voltage level on the MR
applications where both true and complement outputs are required,
and the clock and master reset are common to all storage elements.
TYPE
TYPICAL
f
MAX
74ALS175 70MHz 7mA
outputs. The common buffered
) inputs load and reset (clear) all
input. The device is useful for
TYPICAL
SUPPLY CURRENT
(TOTAL)
PIN CONFIGURATION
MR
GND
Q0
Q0
D0
D1
Q
Q1
1
2
3
4
5
6
1
16
V
CC
Q3
15
Q3
14
D3
13
D2
12
Q
11
2
107
Q2
98
CP
ORDERING INFORMA TION
ORDER CODE
DESCRIPTION COMMERCIAL RANGE
V
= 5V ±10%,
CC
T
= 0°C to +70°C
amb
16-pin plastic DIP 74ALS175N SOT38-4
16-pin plastic SO 74ALS175D SOT109-1
DRAWING
NUMBER
SF00718
INPUT AND OUTPUT LOADING AND FAN-OUT TABLE
PINS DESCRIPTION
D0 – D3 Data inputs 1.0/1.0 20µA/0.1mA
CP Clock Pulse input (active rising edge) 1.0/1.0 20µA/0.1mA
MR Master Reset input (active-Low) 1.0/1.0 20µA/0.1mA
Q0 – Q3 True outputs 20/80 0.4mA/8mA
Q0 – Q3 Complementary outputs 20/80 0.4mA/8mA
NOTE: One (1.0) ALS unit load is defined as: 20µA in the High state and 0.1mA in the Low state.
LOGIC SYMBOL
9
1
VCC = Pin 16
GND = Pin 8
4 5 12 13
D0 D1 D2 D3
CP
MR
Q0 Q0 Q1 Q1 Q2 Q2 Q3 Q3
2 3 7 6 10 11 15 14
SF00719
IEC/IEEE SYMBOL
74ALS (U.L.)
HIGH/LOW
1
9
4
5
12
13
R
C1
1D
LOAD VALUE
HIGH/LOW
2
3
7
6
10
11
15
14
SF00720
1991 Feb 08 853–1024 01670
2
Page 3
Philips Semiconductors Product specification
SYMBOL
PARAMETER
UNIT
74ALS175Quad D flip-flop
LOGIC DIAGRAM
= Pin 16
V
CC
GND = Pin 8
CP
MR
D0
9
1
4
DQ
CP
RD
D1
5
DQ
CP
RD
32 6 1110 14157
Q
0Q0 Q1Q1 Q2Q2 Q3Q3
D2
12
DQ
CP
RD
D3
13
DQ
FUNCTION TABLE
INPUTS OUTPUTS
MR CP D Q
n
Q
n
L X X L H Reset (clear)
H ↑ h H L Load “1”
H ↑ I L H Load “0”
NOTES:
H = High-voltage level
h = High state must be present one setup time before the Low-to-High clock transition
L = Low-voltage level
l = Low state must be present one setup time before the Low-to-High clock transition
X = Don’t care
↑ = Low-to-High clock transition
ABSOLUTE MAXIMUM RATINGS
(Operation beyond the limit set forth in this table may impair the useful life of the device.
Unless otherwise noted these limits are over the operating free air temperature range.)
SYMBOL
V
CC
V
IN
I
IN
V
OUT
I
OUT
T
amb
T
stg
Supply voltage –0.5 to +7.0 V
Input voltage –0.5 to +7.0 V
Input current –30 to +5 mA
Voltage applied to output in High output state –0.5 to V
Current applied to output in Low output state 16 mA
Operating free-air temperature range 0 to +70 °C
Storage temperature range –65 to +150 °C
PARAMETER RATING UNIT
CP
RD
Q
OPERATING
MODE
CC
SF00721
V
RECOMMENDED OPERATING CONDITIONS
V
CC
V
V
I
IK
I
OH
I
OL
T
amb
1991 Feb 08
Supply voltage 4.5 5.0 5.5 V
High-level input voltage 2.0 V
IH
Low-level input voltage 0.8 V
IL
Input clamp current –18 mA
High-level output current –0.4 mA
Low-level output current 8 mA
Operating free-air temperature range 0 +70 °C
LIMITS
MIN NOM MAX
3
Page 4
Philips Semiconductors Product specification
SYMBOL
PARAMETER
TEST CONDITIONS
1
UNIT
VOLLow-level output voltage
CC
,
IL
,
74ALS175Quad D flip-flop
DC ELECTRICAL CHARACTERISTICS
(Over recommended operating free-air temperature range unless otherwise noted.)
LIMITS
MIN TYP
V
OH
V
I
I
IH
I
I
I
CC
High-level output voltage VCC±10%, VIL = MAX, VIH = MIN, IOH = MAX V
I
= 4mA 0.25 0.4 V
p
Input clamp voltage VCC = MIN, II = I
IK
Input current at maximum input voltage VCC = MAX, VI = 7.0V 100 µA
I
VCC = MIN, VIL = MAX,
VIH = MIN
IK
OL
I
= 8mA 0.35 0.50 V
OL
High-level input current VCC = MAX, VI = 2.7V 20 µA
Low-level input current VCC = MAX, VI = 0.5V –0.1 mA
IL
O
Output current
3
VCC = MAX, VO = 2.25V –30 –112 mA
Supply current (total) VCC = MAX 7 14 mA
– 2 V
CC
NOTES:
1. For conditions shown as MIN or MAX, use the appropriate value specified under recommended operating conditions for the applicable type.
2. All typical values are at V
3. The output conditions have been chosen to produce a current that closely approximates one half of the true short-circuit output current, I
= 5V, T
CC
amb
= 25°C.
2
MAX
–0.73 –1.5 V
OS
.
AC ELECTRICAL CHARACTERISTICS
LIMITS
T
= 0°C to +70°C
amb
V
SYMBOL PARAMETER TEST CONDITION
= +5.0V ± 10%
CC
C
= 50pF, RL = 500Ω
L
MIN MAX
f
MAX
t
PLH
t
PHL
t
PLH
t
PHL
Maximum clock frequency Waveform 1 60 MHz
Propagation delay
CP to Qn or CP to Q
n
Waveform 1
3.0
5.0
13.0
16.0
Propagation delay, MR to Qn Waveform 2 3.0 13.0 ns
Propagation delay, MR to Qn Waveform 2 8.0 18.0 ns
AC SETUP REQUIREMENTS
LIMITS
T
= 0°C to +70°C
amb
V
SYMBOL PARAMETER TEST CONDITION
tsu(H)
t
su
th(H)
t
(L)
h
tw(H)
t
(L)
w
Setup time, High or Low
Dn
(L)
to CP
Hold time, High or Low
Dn
to CP
CP pulse width,
High or Low
Waveform 3
Waveform 3
Waveform 1
tw(L) MR pulse width, Low Waveform 2 6.0 ns
t
REC
Recovery time, MR to CP Waveform 2 6.0 ns
= +5.0V ± 10%
CC
C
= 50pF, RL = 500Ω
L
MIN MAX
6.0
6.0
0.0
0.0
8.0
8.0
UNIT
ns
UNIT
ns
ns
ns
1991 Feb 08
4
Page 5
Philips Semiconductors Product specification
74ALS175Quad D flip-flop
AC WAVEFORMS
For all waveforms, VM = 1.3V.
The shaded areas indicate when the input is permitted to change for predictable output performance.
1/f
max
CP
Q
Q
V
M
n
n
t
PHL
t
tw(H)
PLH
V
M
tw(L)
V
M
V
M
V
M
t
PLH
V
M
t
PHL
V
M
SF00722
Waveform 1. Propagation Delay for Clock Input to Output,
Clock Pulse Width,
and Maximum Clock Frequency
MR
CP
Q
Q
n
n
V
t
t
M
tw(L)
PHL
PLH
Waveform 2. Master Reset Pulse Width,
Master Reset to Output Delay,
and Master Reset to Clock Recovery Time
V
M
t
REC
V
M
V
M
V
M
SF00723
CP
Dn
V
V
M
M
th(H)tsu(H)
V
M
V
V
M
M
th(L)tsu(L)
V
M
Waveform 3. Data Setup and Hold Times
TEST CIRCUIT AND WAVEFORMS
V
CC
V
PULSE
GENERATOR
IN
R
T
Test Circuit for Totem-pole Outputs
DEFINITIONS:
R
= Load resistor;
L
see AC electrical characteristics for value.
CL= Load capacitance includes jig and probe capacitance;
see AC electrical characteristics for value.
R
= Termination resistance should be equal to Z
T
pulse generators.
D.U.T.
V
OUT
C
R
L
L
OUT
SC00064
of
NEGATIVE
PULSE
POSITIVE
PULSE
90%
10%
Family
74ALS
V
M
10%
t
THL (tf
t
TLH (tr
90%
V
M
Input Pulse Definition
Amplitude
3.5V
t
w
10%
)
f
)
t
)
TLH (tr
t
)
THL (tf
90%
t
w
90%
V
M
V
M
10%
INPUT PULSE REQUIREMENTS
V
M
1.3V
Rep.Rate
1MHz
500ns
t
w
t
TLHtTHL
2.0ns 2.0ns
AMP (V)
0.3V
AMP (V)
0.3V
SC00005
1991 Feb 08
5
Page 6
Philips Semiconductors Product specification
74ALS175Quad D flip–flop
DIP16: plastic dual in-line package; 16 leads (300 mil) SOT38-4
1991 Feb 08
6
Page 7
Philips Semiconductors Product specification
74ALS175Quad D flip–flop
SO16: plastic small outline package; 16 leads; body width 3.9 mm SOT109-1
1991 Feb 08
7
Page 8
Philips Semiconductors Product specification
74ALS175Quad D flip–flop
DEFINITIONS
Data Sheet Identification Product Status Definition
Objective Specification
Preliminary Specification
Product Specification
Formative or in Design
Preproduction Product
Full Production
Philips Semiconductors and Philips Electronics North America Corporation reserve the right to make changes, without notice, in the products,
including circuits, standard cells, and/or software, described or contained herein in order to improve design and/or performance. Philips
Semiconductors assumes no responsibility or liability for the use of any of these products, conveys no license or title under any patent, copyright,
or mask work right to these products, and makes no representations or warranties that these products are free from patent, copyright, or mask
work right infringement, unless otherwise specified. Applications that are described herein for any of these products are for illustrative purposes
only. Philips Semiconductors makes no representation or warranty that such applications will be suitable for the specified use without further testing
or modification.
LIFE SUPPORT APPLICA TIONS
Philips Semiconductors and Philips Electronics North America Corporation Products are not designed for use in life support appliances, devices,
or systems where malfunction of a Philips Semiconductors and Philips Electronics North America Corporation Product can reasonably be expected
to result in a personal injury. Philips Semiconductors and Philips Electronics North America Corporation customers using or selling Philips
Semiconductors and Philips Electronics North America Corporation Products for use in such applications do so at their own risk and agree to fully
indemnify Philips Semiconductors and Philips Electronics North America Corporation for any damages resulting from such improper use or sale.
Philips Semiconductors
811 East Arques Avenue
P.O. Box 3409
Sunnyvale, California 94088–3409
Telephone 800-234-7381
This data sheet contains the design target or goal specifications for product development. Specifications
may change in any manner without notice.
This data sheet contains preliminary data, and supplementary data will be published at a later date. Philips
Semiconductors reserves the right to make changes at any time without notice in order to improve design
and supply the best possible product.
This data sheet contains Final Specifications. Philips Semiconductors reserves the right to make changes
at any time without notice, in order to improve design and supply the best possible product.
Copyright Philips Electronics North America Corporation 1997
All rights reserved. Printed in U.S.A.
1991 Feb 08
8
Loading...