Datasheet 5962R8766401SA, 5962R8766401RA, 5962R87664012A, 5962-8766401SA, 5962-8766401RA Datasheet (NSC)
...Page 1
54ACT573
Octal Latch with TRI-STATE
®
Outputs
General Description
The ’ACT573 is a high-speed octal latch with buffered common LatchEnable (LE) and buffered common Output Enable
(OE) inputs.
The ’ACT573 is functionally identical to the ’ACT373 but has
inputs and outputs on opposite sides.
Features
n ICCand IOZreduced by 50
%
n Inputs and outputs on opposite sides of package
allowing easy interface with microprocessors
n Useful as input or output port for microprocessors
n Functionally identical to ’ACT373
n TRI-STATE outputs for bus interfacing
n Outputs source/sink 24 mA
n ’ACT573 has TTL-compatible inputs
n Standard Military Drawing (SMD)
— ’ACT573: 5962-87664
Logic Symbols
Pin Names Description
D
0–D7
Data Inputs
LE Latch Enable Input
OE
TRI-STATE Output Enable Input
O
0–O7
TRI-STATE Latch Outputs
TRI-STATE®is a registered trademark of National Semiconductor Corporation.
FACT
®
is a registered trademark of Fairchild Semiconductor Corporation.
DS100332-1
IEEE/IEC
DS100332-2
August 1998
54ACT573 Octal Latch with TRI-STATE Outputs
© 1998 National Semiconductor Corporation DS100332 www.national.com
Page 2
Connection Diagrams
Pin Assignment for DIP
and Flatpak
DS100332-3
Pin Assignment for LCC
DS100332-4
www.national.com 2
Page 3
Functional Description
The ’ACT573 contains eight D-type latches with TRI-STATE
output buffers. When the Latch Enable (LE) input is HIGH,
data onthe D
n
inputs entersthe latches. Inthis condition the
latches are transparent, i.e., a latch output will change state
each time its D input changes. When LE is LOW the latches
store the information that was present on the D inputs a
setup timepreceding the HIGH-to-LOW transition of LE. The
TRI-STATE buffers are controlled by the Output Enable (OE)
input. When OE is LOW, the buffers are enabled. When OE
is HIGH the buffers are in the high impedance mode but this
does not interfere with entering new data into the latches.
Truth Table
Inputs Outputs
OE
LE D O
n
LHH H
LHL L
LLX O
0
HXX Z
H
=
HIGH Voltage
L=LOW Voltage
Z=High Impedance
X=Immaterial
O
0
=
Previous O
0
before HIGH-to-LOW transition of Latch Enable
Logic Diagram
DS100332-5
Please note that this diagram is provided only for the understanding of logic operations and should not be used to estimate propagation delays.
3 www.national.com
Page 4
Absolute Maximum Ratings (Note 1)
If Military/Aerospace specified devices are required,
please contact the National Semiconductor SalesOffice/
Distributors for availability and specifications.
Supply Voltage (V
CC
) −0.5V to +7.0V
DC Input Diode Current (I
IK
)
V
I
=
−0.5V −20 mA
V
I
=
V
CC
+ 0.5V +20 mA
DC Input Voltage (V
I
) −0.5V to VCC+ 0.5V
DC Output Diode Current (I
OK
)
V
O
=
−0.5V −20 mA
V
O
=
V
CC
+ 0.5V +20 mA
DC Output Voltage (V
O
) −0.5V to VCC+ 0.5V
DC Output Source
or Sink Current (I
O
)
±
50 mA
DC V
CC
or Ground Current
per Output Pin (I
CC
or I
GND
)
±
50 mA
Storage Temperature (T
STG
) −65˚C to +150˚C
Junction Temperature (T
J
)
CDIP 175˚C
Recommended Operating
Conditions
Supply Voltage (VCC)
’ACT 4.5V to 5.5V
Input Voltage (V
I
) 0VtoV
CC
Output Voltage (VO) 0VtoV
CC
Operating Temperature (TA)
54ACT −55˚C to +125˚C
Minimum Input Edge Rate (∆V/∆t)
’ACT Devices
V
IN
from 0.8V to 2.0V
V
CC
@
4.5V, 5.5V 125 mV/ns
Note 1: Absolute maximum ratings are those values beyond which damage
to the device may occur. The databook specifications should be met, without
exception, to ensure that the system design is reliable over its power supply,
temperature, and output/input loading variables. National does not recommend operation of FACT
®
circuits outside databook specifications.
DC Characteristics for ’ACT Family Devices
54ACT
Symbol Parameter V
CC
T
A
=
Units Conditions
(V) −55˚C to +125˚C
Guaranteed
Limits
V
IH
Minimum High
Level Input
Voltage
4.5 2.0
V
V
OUT
=
0.1V
5.5 2.0 or V
CC
− 0.1V
V
IL
Maximum Low
Level Input
Voltage
4.5 0.8 V V
OUT
=
0.1V
5.5 0.8 or V
CC
− 0.1V
V
OH
Minimum High
Level Output
Voltage
4.5 4.4 V I
OUT
=
−50 µA
5.5 5.4
(Note 2)
V
IN
=
V
IL
or V
IH
4.5 3.70 V I
OH
−24 mA
5.5 4.70 −24 mA
V
OL
Maximum Low
Level Output
Voltage
4.5 0.1 V I
OUT
=
50 µA
5.5 0.1
(Note 2)
V
IN
=
V
IL
or V
IH
4.5 0.50 V I
OL
24 mA
5.5 0.50 24 mA
I
IN
Maximum Input 5.5
±
1.0 µA V
I
=
V
CC
, GND
Leakage Current
I
OZ
Maximum TRI-STATE 5.5
±
5.0 µA V
I
=
V
IL,VIH
Leakage Current V
O
=
V
CC
, GND
I
CCT
Maximum 5.5 1.6 mA V
I
=
V
CC
− 2.1V
I
CC
/Input
I
OLD
(Note 3) Minimum
Dynamic Output
Current
5.5 50 mA V
OLD
=
1.65V Max
I
OHD
5.5 −50 mA V
OHD
=
3.85V Min
www.national.com 4
Page 5
DC Characteristics for ’ACT Family Devices (Continued)
54ACT
Symbol Parameter V
CC
T
A
=
Units Conditions
(V) −55˚C to +125˚C
Guaranteed
Limits
I
CC
Maximum Quiescent
Supply Current
5.5 80.0 µA V
IN
=
V
CC
or GND
Note 2: All outputs loaded; thresholds on input associated with output under test.
Note 3: Maximum test duration 2.0 ms, one output loaded at a time.
Note 4: I
CC
for 54ACT@25˚C is identical to 74ACT@25˚C.
AC Electrical Characteristics
54ACT
V
CC
T
A
=
−55˚C Fig.
Symbol Parameter (V) to +125˚C Units No.
(Note 5) C
L
=
50 pF
Min Max
t
PLH
Propagation Delay 5.0 1.5 13.5 ns
D
m
to O
n
t
PHL
Propagation Delay 5.0 1.5 13.5 ns
D
n
to O
n
t
PLH
Propagation Delay 5.0 1.5 13.0 ns
LE to O
n
t
PHL
Propagation Delay 5.0 1.5 12.0 ns
LE to O
n
t
PZH
Output Enable Time 5.0 1.5 11.5 ns
t
PZL
Output Enable Time 5.0 1.5 11.0 ns
t
PHZ
Output Disable Time 5.0 1.5 13.5 ns
t
PLZ
Output Disable Time 5.0 1.5 10.5 ns
Note 5: Voltage Range 5.0 is 5.0V±0.5V
AC Operating Requirements
54ACT
V
CC
T
A
=
−55˚C Fig.
Symbol Parameter (V) to +125˚C Units No.
(Note 6) C
L
=
50 pF
Guaranteed
Minimum
t
s
Setup Time, HIGH or LOW 5.0 4.5 ns
D
n
to LE
t
h
Hold Time, HIGH or LOW 5.0 1.0 ns
D
n
to LE
t
w
LE Pulse Width, HIGH 5.0 5.0 ns
Note 6: Voltage Range 5.0 is 5.0V±0.5V
5 www.national.com
Page 6
Capacitance
Symbol Parameter Typ Units Conditions
C
IN
Input Capacitance 5.0 pF V
CC
=
OPEN
C
PD
Power Dissipation 25.0 pF V
CC
=
5.0V
Capacitance
www.national.com 6
Page 7
7
Page 8
Physical Dimensions inches (millimeters) unless otherwise noted
20 Terminal Ceramic Leadless Chip Carrier (L)
NS Package Number E20A
www.national.com 8
Page 9
Physical Dimensions inches (millimeters) unless otherwise noted (Continued)
20-Lead Ceramic Dual-In-Line Package (D)
NS Package Number J20A
20-Lead Ceramic Flatpak (F)
NS Package Number W20A
9 www.national.com
Page 10
LIFE SUPPORT POLICY
NATIONAL’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein:
1. Life support devices or systems are devices or systems which, (a) are intended for surgical implant into
the body, or (b)support or sustain life, andwhose failure to perform when properly used in accordance
with instructions for use provided in the labeling, can
be reasonably expected toresult in a significant injury
to the user.
2. A critical component in any component of a life support
device or system whose failure to perform can be reasonably expectedto cause the failure of the life support
device or system, orto affect its safety oreffectiveness.
National Semiconductor
Corporation
Americas
Tel: 1-800-272-9959
Fax: 1-800-737-7018
Email: support@nsc.com
www.national.com
National Semiconductor
Europe
Fax: +49 (0) 1 80-530 85 86
Email: europe.support@nsc.com
Deutsch Tel: +49 (0) 1 80-530 85 85
English Tel: +49 (0) 1 80-532 78 32
Français Tel: +49 (0) 1 80-532 93 58
Italiano Tel: +49 (0) 1 80-534 16 80
National Semiconductor
Asia Pacific Customer
Response Group
Tel: 65-2544466
Fax: 65-2504466
Email: sea.support@nsc.com
National Semiconductor
Japan Ltd.
Tel: 81-3-5620-6175
Fax: 81-3-5620-6179
54ACT573 Octal Latch with TRI-STATE Outputs
National does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and National reserves the right at any time without notice to change said circuitry and specifications.
Loading...