Page 1
Transistors
Power transistor (60V, 2A)
2SC5880
zFeatures
1) High speed switching.
(tf : Ty p. : 35ns
at IC = 2A)
2) Low saturation voltage, typically
(Typ. : 200mV
at IC = 1.0A, IB = 100mA)
3) Strong discharge power for inductive load and
capacitance load.
4) Complements the 2SA2093
zApplications
Low frequency amplifier
High speed switching
zDimensions (Unit : mm)
ATV
(1) Emitter
(2) Collector
(3) Base
Symbol : C5880
2SC5880
Taping specifications
zStructure
NPN Silicon epitaxial planar transistor
zPackaging specifications
Taping
TV2
2500
Type
2SC5880
Package
Code
Basic ordering unit (pieces)
zAbsolute maximum ratings (Ta=25°C)
Parameter
Collector-base voltage
Collector-emitter voltage
Emitter-base voltage
Collector current
Power dissipation
Junction temperature
Range of storage temperature
∗Pw=10ms
DC
Pulsed
Symbol
V
CBO
V
CEO
V
EBO
I
C
I
CP
P
C
t
j
t
stg
Limits Unit
60
60
6
2
4
1.0
150
−55 to 150
W
°C
°C
V
V
V
A
∗
A
Rev.B 1/3
Page 2
Transistors
zElectrical characteristics (T a=25°C)
Parameter Symbol Min. Typ. Max. Unit Condition
Collector-emitter breakdown voltage
Collector-base breakdown voltage
Emitter-base breakdown voltage
Collector cut-off current
Emitter cut-off current
Collector-emitter saturation voltage
DC current gain
Transition frequency
Corrector output capacitance
Turn-on time
Storage time
Fall time
∗Non repetitive pulse
FE RANK
zh
Q
120−270
180−390
zElectrical characteristic curves
10
(A)
C
1
Ta=125°C
Ta=25°C
Ta= −40°C
0.1
COLLECTOR CURRENT : I
0.01
0 1.510.5
BASE TO EMITTER VOLTAGE : VBE (V)
Fig.1 Grounded Emitter
Propagation Characteristics
10
R
VCE=2V
Ta=25°C
BV
BV
BV
V
CEO
CBO
EBO
I
CBO
I
EBO
CE (sat)
h
FE
f
T
Cob
on
t
t
stg
t
f
60
60
6
−
−
−
120
−
−
−
−
−
1000
FE
100
10
DC CURRENT GAIN : h
−
−
−
−
−
500
200
390
−
200
10
50
120
35
1
0.001 0.01 0.1 1 10
COLLECTOR CURRENT : IC (A)
Fig.2 DC Current Gain vs.
Collector Current (Ι)
10
−
−
−
1.0
1.0
−
−
−
−
−
VCE=5V
V
V
CE
CE
=3V
=2V
V
V
V
µA
µA
mV
−
MHz
pF
ns
ns
ns
Ta=25°C
IC / IB=10 / 1
IC=1mA
I
C
=100µA
E
=100µA
I
V
CB
=40V
EB
=4V
V
I
C
=1.0A
I
B
=0.1A
V
CE
=2V
C
=100mA
I
V
CE
=10V
I
E
= −100mA
f=10MHz
CB
=10V
V
I
E
=0mA
f=1MHz
C
=2A
I
IB1=200mA
IB2= −200mA
V
CC
25V
1000
FE
DC CURRENT GAIN : h
2SC5880
∗
VCE=2V
100
Ta=125°C
Ta=25°C
Ta= −40°C
10
1
0.001 0.01 0.1 1 10
COLLECTOR CURRENT : IC (A)
Fig.3 DC Current Gain vs.
Collector Current (ΙΙ)
10
IC / IB=10 / 1
1
(V)
CE (sat)
COLLECTOR SATURATION
VOLTAGE : V
0.01
IC / IB=20 / 1
C
/ IB=10 / 1
I
0.1
0.001 1010.10.01
COLLECTOR CURRENT : IC (A)
Fig.4
Collector-Emitter Saturation
Voltage vs. Collector Current (Ι)
1
(V)
CE (sat)
0.1
COLLECTOR SATURATION
VOLTAGE : V
0.01
Fig.5
Ta=125°C
Ta=25°C
Ta= −40°C
0.001 1010.10.01
COLLECTOR CURRENT : IC (A)
Collector-Emitter Saturation
Voltage vs. Collector Current (ΙΙ)
1
(V)
BE (sat)
0.1
BASE EMITTER SATURATION
VOLTAGE : V
0.01
0.001 1010.10.01
COLLECTOR CURRENT : IC (A)
Ta=125°C
Ta=25°C
Ta= −40°C
Fig.6 Base-Emitter Saturation
Voltage vs. Collecter Current
Rev.B 2/3
Page 3
Transistors
1000
100
Ta=25°C
CE
=10V
V
100
Ta=25°C
f=1MHz
1000
tstg
2SC5880
Ta=25°C
CC
=25V
V
C
/ IB=10 / 1
I
10
10
COLLECTOR OUTPUT
CAPACITANCE : Cob (pF)
TRANSITION FREQUENCY : fT (MHz)
1
0.001 1010.10.01
EMITTER CURRENT : IE (A)
Fig.7 Transition Frequency
1
0.1 1 10 100
BASE TO COLLECTOR VOLTAGE : V
Fig.8
10
(A)
C
1
0.1
0.01
Single
COLLECTOR CURRENT : I
non repetitive
Pulsed
0.001
0.01 1001010.1
COLLECTOR TO EMITTER VOLTAGE : VCE (V)
100ms
10ms
DC
Fig.10 Safe Operating Area
1ms
zSwitching characteristics measurement circuits
V
IN
(V)
CB
Collector Output Capacitance
RL=12.5Ω
B1
I
I
C
100
SWITCHING TIME : (ns)
10
0.01 1010.1
tf
ton
COLLECTOR CURRENT : IC (A)
Fig.9 Switching Time
P
W
PW 50 S
B2
I
VCC 25V
Duty cycle ≤ 1%
I
B1
I
Base current
waveform
B2
90%
I
Collector current
waveform
10%
ton tstg tf
C
Rev.B 3/3
Page 4
Appendix
Notes
No technical content pages of this document may be reproduced in any form or transmitted by any
means without prior permission of ROHM CO.,LTD.
The contents described herein are subject to change without notice. The specifications for the
product described in this document are for reference only. Upon actual use, therefore, please request
that specifications to be separately delivered.
Application circuit diagrams and circuit constants contained herein are shown as examples of standard
use and operation. Please pay careful attention to the peripheral conditions when designing circuits
and deciding upon circuit constants in the set.
Any data, including, but not limited to application circuit diagrams information, described herein
are intended only as illustrations of such devices and not as the specifications for such devices. ROHM
CO.,LTD. disclaims any warranty that any use of such devices shall be free from infringement of any
third party's intellectual property rights or other proprietary rights, and further, assumes no liability of
whatsoever nature in the event of any such infringement, or arising from or connected with or related
to the use of such devices.
Upon the sale of any such devices, other than for buyer's right to use such devices itself, resell or
otherwise dispose of the same, no express or implied right or license to practice or commercially
exploit any intellectual property rights or other proprietary rights owned or controlled by
ROHM CO., LTD. is granted to any such buyer.
Products listed in this document are no antiradiation design.
The products listed in this document are designed to be used with ordinary electronic equipment or devices
(such as audio visual equipment, office-automation equipment, communications devices, electrical
appliances and electronic toys).
Should you intend to use these products with equipment or devices which require an extremely high level
of reliability and the malfunction of which would directly endanger human life (such as medical
instruments, transportation equipment, aerospace machinery, nuclear-reactor controllers, fuel controllers
and other safety devices), please be sure to consult with our sales representative in advance.
It is our top priority to supply products with the utmost quality and reliability. However, there is always a chance
of failure due to unexpected factors. Therefore, please take into account the derating characteristics and allow
for sufficient safety features, such as extra margin, anti-flammability, and fail-safe measures when designing in
order to prevent possible accidents that may result in bodily harm or fire caused by component failure. ROHM
cannot be held responsible for any damages arising from the use of the products under conditions out of the
range of the specifications or due to non-compliance with the NOTES specified in this catalog.
Thank you for your accessing to ROHM product informations.
More detail product informations and catalogs are available, please contact your nearest sales office.
ROHM Customer Support System
www.rohm.com
THE AMERICAS / EUROPE / ASIA / JAPAN
Contact us : webmaster@ rohm.co. jp
Copyright © 2008 ROHM CO.,LTD.
21 Saiin Mizosaki-cho, Ukyo-ku, Kyoto 615-8585, Japan
TEL : +81-75-311-2121
FAX : +81-75-315-0172
Appendix1-Rev2.0
Page 5
Loading...