Dataram DRI520P6 User Manual
CUSTOMER SUPPORT
Dataram's Technical Support Program goes beyond the lifetime warranty,
routine calls and questions. As memory specialists since 1967, we want
to provide the most comprehensive level of service and support in the
industry.
Our Customer Support representatives can answer your questions and
give you information on system/memory configurations, upgrade options,
product specifications, compatibility and other technical topics or issues.
In Europe:
+45 70 212 217 (Phone)
+45 70 212 211 (FAX)
eusupport@dataram.com (E-mail)
In the U.S.A. and all other countries:
800-599-0071 (Toll Free)
609-799-0071 (Phone)
609-799-6734 (FAX)
usasupport@dataram.com (E-mail)
If a Dataram memory board does not function properly we will issue a
Return Material Authorization number (RMA#) for the return of the
defective module(s) and express ship a repair or replacement to you at
no charge.
P/N 06707 A
for IBM Power 520 (E4A, M15, M25) / Power 550 (M50, E8A) Systems
SYSTEM AND MEMORY OVERVIEW
Note: Refer to your system owner’s manual for detailed instructions and be
sure to follow all static and safety precautions.
IBM Power 520 Model M15:
• Minimum memory is 2GB (2X1GB), Maximum is 16GB (4X4GB).
• Memory installed in 2 banks, mixing capacities not supported.
IBM Power 520 Model M25:
• Minimum memory is 2GB (2X1GB), Maximum is 32GB (4X8GB).
• Memory installed in 2 banks, mixing capacities not supported.
IBM Power 520 Model E4A:
• Minimum memory is 2GB (2X1GB), Maximum is 64GB (8X8GB).
• Memory modules behind each processor module must be the
IBM Power 550 Model M50:
• Minimum memory is 2GB (2X1GB), Maximum is 128GB
• Capacity cannot be mixed on the same processor card.
IBM Power 550 Model E8A:
• Minimum capcity is 2GB (2X1GB), Maximum is 256 GB
• Capacity cannot be mixed on the same processor card.
DRI520P6 INSTALLATION INSTRUCTIONS
same capacity and speed.
(16X8GB) across 2 processor cards. Installed in banks of 2.
(32X8GB) across 4 processor cards. Installed in banks of 2.
P/N 06707 A
CUSTOMER SUPPORT
Dataram's Technical Support Program goes beyond the lifetime warranty,
routine calls and questions. As memory specialists since 1967, we want
to provide the most comprehensive level of service and support in the
industry.
Our Customer Support representatives can answer your questions and
give you information on system/memory configurations, upgrade options,
product specifications, compatibility and other technical topics or issues.
In Europe:
+45 70 212 217 (Phone)
+45 70 212 211 (FAX)
eusupport@dataram.com (E-mail)
In the U.S.A. and all other countries:
800-599-0071 (Toll Free)
609-799-0071 (Phone)
609-799-6734 (FAX)
usasupport@dataram.com (E-mail)
If a Dataram memory board does not function properly we will issue a
Return Material Authorization number (RMA#) for the return of the
defective module(s) and express ship a repair or replacement to you at
no charge.
P/N 06707 A
for IBM Power 520 (E4A, M15, M25) / Power 550 (M50, E8A) Systems
SYSTEM AND MEMORY OVERVIEW
Note: Refer to your system owner’s manual for detailed instructions and be
sure to follow all static and safety precautions.
IBM Power 520 Model M15:
• Minimum memory is 2GB (2X1GB), Maximum is 16GB (4X4GB).
• Memory installed in 2 banks, mixing capacities not supported.
IBM Power 520 Model M25:
• Minimum memory is 2GB (2X1GB), Maximum is 32GB (4X8GB).
• Memory installed in 2 banks, mixing capacities not supported.
IBM Power 520 Model E4A:
• Minimum memory is 2GB (2X1GB), Maximum is 64GB (8X8GB).
• Memory modules behind each processor module must be the
IBM Power 550 Model M50:
• Minimum memory is 2GB (2X1GB), Maximum is 128GB
• Capacity cannot be mixed on the same processor card.
IBM Power 550 Model E8A:
• Minimum capcity is 2GB (2X1GB), Maximum is 256 GB
• Capacity cannot be mixed on the same processor card.
DRI520P6 INSTALLATION INSTRUCTIONS
same capacity and speed.
(16X8GB) across 2 processor cards. Installed in banks of 2.
(32X8GB) across 4 processor cards. Installed in banks of 2.
P/N 06707 A
MEMORY INSTALLATION
g
g
g
g
Note: Refer to your system owner’s manual for detailed instructions.
Caution: System parts are sensitive to electrostatic discharge and can be
• Shut down and unplug the system, then remove the cover.
• Remove air baffle and fans by lifting the 4 tabs and lifting the baffle
damaged by the static charge you may carry. You should wear a
rounded wrist strap.
(Models E4A, M15, and M25)
out of the system (See Figure 1).
IBM P520
MEMORY INSTALLATION
Note: Refer to your system owner’s manual for detailed instructions.
Caution: System parts are sensitive to electrostatic discharge and can be
• Shut down and unplug the system, then remove the cover.
• Remove the system processor assembly by lifting the handles up
• Each processor assembly has 8 memory slots. The memory
• The numbering scheme is listed in Figure 1 below.
damaged by the static charge you may carry. You should wear a
rounded wrist strap.
(Model M50 and E8A)
and pulling it out of the system, and place it on a static-free surface.
modules should be installed in the order listed in your user guide.
IBM P550
Figure 1 Figure 2
• Each system has 8 memory module slots. The memory modules
should be installed in the order listed in your user guide.
• Remove the memory module fillers if present.
• Ensure that the connector locking tabs are in the unlocked position.
• Align the memory module notch with the key in the connector to
ensure that the module is installed properly and not damaged.
• Push the memory module firmly into the connector until the locking
tabs engage (See Figure 2).
• Replace the air baffle and put the cover back on.
MEMORY INSTALLATION
Note: Refer to your system owner’s manual for detailed instructions.
Caution: System parts are sensitive to electrostatic discharge and can be
• Shut down and unplug the system, then remove the cover.
• Remove air baffle and fans by lifting the 4 tabs and lifting the baffle
damaged by the static charge you may carry. You should wear a
rounded wrist strap.
(Models E4A, M15, and M25)
out of the system (See Figure 1).
IBM P520
Figure 1 Figure 2
• Remove the memory module fillers if present.
• Ensure that the connector locking tabs are in the unlocked position.
• Align the memory module notch with the key in the connector to
ensure that the module is installed properly and not damaged.
• Push the memory module firmly into the connector until the locking
tabs engage (See Figure 2).
• Replace the air baffle and put the cover back on.
MEMORY INSTALLATION
Note: Refer to your system owner’s manual for detailed instructions.
Caution: System parts are sensitive to electrostatic discharge and can be
• Shut down and unplug the system, then remove the cover.
• Remove the system processor assembly by lifting the handles up
• Each processor assembly has 8 memory slots. The memory
• The numbering scheme is listed in Figure 1 below.
damaged by the static charge you may carry. You should wear a
rounded wrist strap.
and pulling it out of the system, and place it on a static-free surface.
modules should be installed in the order listed in your user guide.
(Model M50 and E8A)
IBM P550
Figure 1 Figure 2
• Each system has 8 memory module slots. The memory modules
should be installed in the order listed in your user guide.
• Remove the memory module fillers if present.
• Ensure that the connector locking tabs are in the unlocked position.
• Align the memory module notch with the key in the connector to
ensure that the module is installed properly and not damaged.
• Push the memory module firmly into the connector until the locking
tabs engage (See Figure 2).
• Replace the air baffle and put the cover back on.
Figure 1 Figure 2
• Remove the memory module fillers if present.
• Ensure that the connector locking tabs are in the unlocked position.
• Align the memory module notch with the key in the connector to
ensure that the module is installed properly and not damaged.
• Push the memory module firmly into the connector until the locking
tabs engage (See Figure 2).
• Replace the air baffle and put the cover back on.
Loading...