Page 1
CUSTOMER SUPPORT
Dataram's Technical Support Program goes beyond the lifetime warranty,
routine calls and questions. As memory specialists since 1967, we want
to provide the most comprehensive level of service and support in the
industry.
Our Customer Support representatives can answer your questions and
give you information on system/memory configurations, upgrade options,
product specifications, compatibility and other technical topics or issues.
In Europe:
+45 70 212 217 (Phone)
+45 70 212 211 (FAX)
eusupport@dataram.com (E-mail)
In the U.S.A. and all other countries:
800-599-0071 (Toll Free)
609-799-0071 (Phone)
609-936-1369 (FAX)
usasupport@dataram.com (E-mail)
If a Dataram memory board does not function properly we will issue a
Return Material Authorization number (RMA#) for the return of the
defective module(s) and express ship a repair or replacement to you at
no charge.
P/N 06706 A
DRHXW8400 and DRHXW8600 INSTALLATION
INSTRUCTIONS FOR HP xw8600 Workstations
SYSTEM AND MEMORY OVERVIEW
Note: Refer to your system owner’s manual for detailed instructions and be
sure to follow all static and safety precautions.
System Board Configuration:
The xw8600 has 8 DIMM slots on the system board for up to 32GB
(8 x 4GB) of PC2-5300F 667 MHz ECC fully buffered DDR2 memory.
Available system board DIMM sizes are: 1GB, 2GB, and 4GB.
Note: *8GB DIMMs are not supported on the system board*
System board is configurable for Single Channel (one DIMM), Dual
Channel (two DIMMs), or Quad Channel (sets of four DIMMs).
Memory Riser Card Configuration:
The xw8600 riser cards have 16 DIMM slots for up to 128GB (16 x 8GB) of
PC2-5300F 667 MHz ECC fully buffered DDR2 memory.
Available riser card DIMM sizes are: 2GB, 4GB, and 8GB.
Memory on riser cards are configurable as Quad Channel only.
P/N 06706 A
CUSTOMER SUPPORT
Dataram's Technical Support Program goes beyond the lifetime warranty,
routine calls and questions. As memory specialists since 1967, we want
to provide the most comprehensive level of service and support in the
industry.
Our Customer Support representatives can answer your questions and
give you information on system/memory configurations, upgrade options,
product specifications, compatibility and other technical topics or issues.
In Europe:
+45 70 212 217 (Phone)
+45 70 212 211 (FAX)
eusupport@dataram.com (E-mail)
In the U.S.A. and all other countries:
800-599-0071 (Toll Free)
609-799-0071 (Phone)
609-936-1369 (FAX)
usasupport@dataram.com (E-mail)
If a Dataram memory board does not function properly we will issue a
Return Material Authorization number (RMA#) for the return of the
defective module(s) and express ship a repair or replacement to you at
no charge.
P/N 06706 A
DRHXW8400 and DRHXW8600 INSTALLATION
INSTRUCTIONS FOR HP xw8600 Workstations
SYSTEM AND MEMORY OVERVIEW
Note: Refer to your system owner’s manual for detailed instructions and be
sure to follow all static and safety precautions.
System Board Configuration:
The xw8600 has 8 DIMM slots on the system board for up to 32GB
(8 x 4GB) of PC2-5300F 667 MHz ECC fully buffered DDR2 memory.
Available system board DIMM sizes are: 1GB, 2GB, and 4GB.
Note: *8GB DIMMs are not supported on the system board*
System board is configurable for Single Channel (one DIMM), Dual
Channel (two DIMMs), or Quad Channel (sets of four DIMMs).
Memory Riser Card Configuration:
The xw8600 riser cards have 16 DIMM slots for up to 128GB (16 x 8GB) of
PC2-5300F 667 MHz ECC fully buffered DDR2 memory.
Available riser card DIMM sizes are: 2GB, 4GB, and 8GB.
Memory on riser cards are configurable as Quad Channel only.
P/N 06706 A
Page 2
MEMORY INSTALLATION
Note: Refer to your system owner’s manual for detailed instructions.
System Board Configuration:
If installing only one DIMM, install it in socket 1.
If installing only two DIMMs, install them in socket pair: 1/5.
If installing four DIMMs, install them in socket pairs: 1/3 and 5/7.
If installing six DIMMs, install them in socket pairs: 1/3, 5/7, and 2/4.
If installing eight DIMMS, install them in socket pairs: 1/3, 5/7, 2/4, and 6/8.
MEMORY INSTALLATION
Note: Refer to your system owner’s manual for detailed instructions.
Memory Riser Card Configuration:
Note: To use a memory riser assembly, your workstation must be
equipped with a 1050W power supply and high performance processor
heatsinks.
• Install the memory riser card guide into memory slots 2, 4, 6, and
8 in the workstation chassis. (See Figure 1)
• Install the DIMMs in the memory riser cards, using identical
DIMMs in each riser.
• Install blank riser fillers in the slots that are not being used.
• Install loaded memory risers into riser card guide. (See Figure 2)
• Install the memory riser card power cable by connecting each
memory card power cable connector into the power connector on
a memory card. (See figure 3)
• Insert the memory riser card power cable into the notch on the
riser card guide and connect memory riser cable to the power
supply cable.
• Install the memory fan/duct assembly by placing the rear of the
assembly under the chassis lip. Lower it into the chassis, then
secure the assembly thumbscrews.
• Disconnect power and remove side access panel
• Press the green button at the base of the fan and lift it up to expose
memory sockets.
• Align the DIMM connector key with the DIMM socket key and press
down to seat the modules firmly, securing the socket levers.
• Lower the memory fan until it snaps into place (ensuring all cables are
clear of the fan housing).
MEMORY INSTALLATION
Note: Refer to your system owner’s manual for detailed instructions.
System Board Configuration:
If installing only one DIMM, install it in socket 1.
If installing only two DIMMs, install them in socket pair: 1/5.
If installing four DIMMs, install them in socket pairs: 1/3 and 5/7.
If installing six DIMMs, install them in socket pairs: 1/3, 5/7, and 2/4.
If installing eight DIMMS, install them in socket pairs: 1/3, 5/7, 2/4, and 6/8.
Figure 1 Figure 2 Figure 3
Caution: System parts are sensitive to electrostatic discharge and can be damaged by
the static charge you may carry. You should wear a grounded wrist strap.
MEMORY INSTALLATION
Note: Refer to your system owner’s manual for detailed instructions.
Memory Riser Card Configuration:
Note: To use a memory riser assembly, your workstation must be
equipped with a 1050W power supply and high performance processor
heatsinks.
• Install the memory riser card guide into memory slots 2, 4, 6, and
8 in the workstation chassis. (See Figure 1)
• Install the DIMMs in the memory riser cards, using identical
DIMMs in each riser.
• Install blank riser fillers in the slots that are not being used.
• Install loaded memory risers into riser card guide. (See Figure 2)
• Install the memory riser card power cable by connecting each
memory card power cable connector into the power connector on
a memory card. (See figure 3)
• Insert the memory riser card power cable into the notch on the
riser card guide and connect memory riser cable to the power
supply cable.
• Install the memory fan/duct assembly by placing the rear of the
assembly under the chassis lip. Lower it into the chassis, then
secure the assembly thumbscrews.
• Disconnect power and remove side access panel
• Press the green button at the base of the fan and lift it up to expose
memory sockets.
• Align the DIMM connector key with the DIMM socket key and press
down to seat the modules firmly, securing the socket levers.
• Lower the memory fan until it snaps into place (ensuring all cables are
clear of the fan housing).
Figure 1 Figure 2 Figure 3
Caution: System parts are sensitive to electrostatic discharge and can be damaged by
the static charge you may carry. You should wear a grounded wrist strap.
Loading...