Page 1
CUSTOMER SUPPORT
Dataram's Technical Support Program goes beyond the lifetime warranty,
routine calls and questions. As memory specialists for nearly 40 years,
we want to provide the most comprehensive level of service and support
in the industry.
Our Customer Support representatives can answer your questions and
give you information on system/memory configurations, upgrade options,
product specifications, compatibility and other technical topics or issues.
In Europe:
+45 70 212 217 (Phone)
+45 70 212 211 (FAX)
eusupport@dataram.com (E-mail)
In the U.S.A. and all other countries:
800-599-0071 (Toll Free)
609-799-0071 (Phone)
609-936-1369 (FAX)
usasupport@dataram.com (E-mail)
If a Dataram memory board does not function properly we will issue a
Return Material Authorization number (RMA#) for the return of the
defective module(s) and express ship a repair or replacement to you at
no charge.
P/N 06688 B
DRHXW6200/8200 INSTALLATION INSTRUCTIONS
FOR HP XW6200 AND XW8200 WORKSTATIONS
SYSTEM AND MEMORY OVERVIEW
Note: Refer to your system owner’s manual for detailed instructions and be
sure to follow all static and safety precautions.
• The HP xw6200 workstation supports up to 8GB and the xw8200 up
to 16GB, of high-speed Dual Channel DDR2 400MHz ECC SDRAM
memory
• Except for a single DIMM installed in slot 1, odd numbered DIMMs
are not supported
• Additional DIMMs should be installed in matched pairs
• If installing both single and dual-rank DIMMs in the xw6200, the dual-
rank DIMMs must be installed in slots 1 and 2. In the xw8200, the
dual-rank DIMMs must be installed in slots 1 and 2, and then slots 3
and 4. Dual-rank DIMMs are not supported in slots 5-8 of the
xw8200.
Capacity Dataram Product Description HP Product
512MB DRHXW8200/512 512MB SR DIMM DY658A
1GB DRHXW8200/1GB 1GB SR DIMM DY655A
2GB DRHXW6200/2GB 2GB DR DIMM DY657A (xw6200 only)
2GB DRHXW8200/2GB 2GB SR DIMM PH201A (xw8200 only)
(SR=Single-Rank, DR=Dual-Rank)
P/N 06688 B
CUSTOMER SUPPORT
Dataram's Technical Support Program goes beyond the lifetime warranty,
routine calls and questions. As memory specialists for nearly 40 years,
we want to provide the most comprehensive level of service and support
in the industry.
Our Customer Support representatives can answer your questions and
give you information on system/memory configurations, upgrade options,
product specifications, compatibility and other technical topics or issues.
In Europe:
+45 70 212 217 (Phone)
+45 70 212 211 (FAX)
eusupport@dataram.com (E-mail)
In the U.S.A. and all other countries:
800-599-0071 (Toll Free)
609-799-0071 (Phone)
609-936-1369 (FAX)
usasupport@dataram.com (E-mail)
If a Dataram memory board does not function properly we will issue a
Return Material Authorization number (RMA#) for the return of the
defective module(s) and express ship a repair or replacement to you at
no charge.
P/N 06688 B
DRHXW6200/8200 INSTALLATION INSTRUCTIONS
FOR HP XW6200 AND XW8200 WORKSTATIONS
SYSTEM AND MEMORY OVERVIEW
Note: Refer to your system owner’s manual for detailed instructions and be
sure to follow all static and safety precautions.
• The HP xw6200 workstation supports up to 8GB and the xw8200 up
to 16GB, of high-speed Dual Channel DDR2 400MHz ECC SDRAM
memory
• Except for a single DIMM installed in slot 1, odd numbered DIMMs
are not supported
• Additional DIMMs should be installed in matched pairs
• If installing both single and dual-rank DIMMs in the xw6200, the dual-
rank DIMMs must be installed in slots 1 and 2. In the xw8200, the
dual-rank DIMMs must be installed in slots 1 and 2, and then slots 3
and 4. Dual-rank DIMMs are not supported in slots 5-8 of the
xw8200.
Capacity Dataram Product Description HP Product
512MB DRHXW8200/512 512MB SR DIMM DY658A
1GB DRHXW8200/1GB 1GB SR DIMM DY655A
2GB DRHXW6200/2GB 2GB DR DIMM DY657A (xw6200 only)
2GB DRHXW8200/2GB 2GB SR DIMM PH201A (xw8200 only)
(SR=Single-Rank, DR=Dual-Rank)
P/N 06688 B
Page 2
MEMORY REMOVAL
g
y
g
y
Note: Refer to your system owner’s manual for detailed instructions.
Caution: System parts are sensitive to electrostatic discharge and can be
damaged by the static charge you may carry. You should wear a
rounded wrist strap.
1. Turn off the system and peripheral devices, and disconnect the power
cords and all external cables.
2. If you need to remove existing memory (to replace with higher density
modules for example), do that now by pressing down on the ejection
levers on both sides of module slots. Carefully pull the modules straight
out of the slots and set them down on an antistatic mat.
MEMORY INSTALLATION
3. Open both ejector levers on each slot.
4. Position a module over the slot so that the alignment notches on the
DIMM match the notches on the connector.
5. Press firmly with your thumbs on both top ends of the module, applying
equal pressure until the module snaps into place. Lock the module in the
socket by pushing up on the ejector levers until they are in their upright
position.
HP xw6200 Workstation
HP xw8200 Workstation
Caution: Confirm the modules are fully and evenly seated in the slots.
Improper seating can cause electrical shorts that can damage
the memor
and/or the system.
6. Continue to install the remaining memory modules until you have filled
the bank with two identical modules. Repeat the above steps for each
bank of memory you wish to install.
7. Reconnect the power cords and external cables, and turn on the system.
8. After you reboot, ensure the system recognizes the new memory
configuration.
MEMORY REMOVAL MEMORY INSTALLATION
Note: Refer to your system owner’s manual for detailed instructions. 3. Open both ejector levers on each slot.
Caution: System parts are sensitive to electrostatic discharge and can be
damaged by the static charge you may carry. You should wear a
rounded wrist strap.
1. Turn off the system and peripheral devices, and disconnect the power
cords and all external cables.
4. Position a module over the slot so that the alignment notches on the
DIMM match the notches on the connector.
5. Press firmly with your thumbs on both top ends of the module, applying
equal pressure until the module snaps into place. Lock the module in the
socket by pushing up on the ejector levers until they are in their upright
position.
2. If you need to remove existing memory (to replace with higher density
modules for example), do that now by pressing down on the ejection
levers on both sides of module slots. Carefully pull the modules straight
out of the slots and set them down on an antistatic mat.
HP xw6200 Workstation
HP xw8200 Workstation
Caution: Confirm the modules are fully and evenly seated in the slots.
Improper seating can cause electrical shorts that can damage
the memor
and/or the system.
6. Continue to install the remaining memory modules until you have filled
the bank with two identical modules. Repeat the above steps for each
bank of memory you wish to install.
7. Reconnect the power cords and external cables, and turn on the system.
8. After you reboot, ensure the system recognizes the new memory
configuration.
Loading...