Datamax-O'Neil Vehicle Mount Bracket User Manual

PrintPAD Vehicle Mount Bracket

Mounting

Locking lever

PrintPAD printer

holes (4)

Padlock hole

Locking lever

Unlocked Locked

Rubber feet (4 sets) Washers (included)

1/4” x 20° pan head screws (not included)

(included)

Place feet here

Front

Back

Mounting holes (4)

Mounting dimensions

* Drill holes 9/32”

diameter

* Use 1/4” - 20

° pan head

screws (the length is

determined by the
thickness of the
mounting surface)

(220257-000)

Selecting a Location

General Guidelines

• Position the bracket so there is enough room to
properly open and close the printer.

• Position the bracket so the printer is pro tected from
environmental elements such as moisture, tools,
and boxes.

• Position the bracket in a secure area within normal
traffic patterns.

• Do not position the bracket above, near, or relative
to the driver’s position as to interfere with normal
driving operations.

• Mount the bracket away from the driver’s head to
eliminate potential injury in the event of an
accident.

• Use only 1/4” x 20° pan head head screws for
mounting.

• Datamax-O’Neil does not accept liability for
improperly mounted or poorly placed mounting
brackets and/or printers.

• The PrintPAD Vehicle Mount Bracket works with
the PrintPAD 7900 and 9000 printers
(manufactured after March 1, 2007).

Step 1: Mounting the Bracket

1. Attach the feet to the mounting holes.

2. Use the PrintPAD Vehicle Mount Bracket as a
template to mark the four mounting holes on the
mounting surface. For guidelines on mounting and/
or installation, see Selecting a Location.

3. Drill the mounting holes at the marked locations.

4. Attach the bracket to the mounting surface using
1/4” - 20 pan head screws (not included) and the
washers (included). Thread the screws through the
washers and the mounting holes with a 1/4”- 20 nut

and lock washer, using Loctite

5. Tighten securely without crushing the rubber feet.
Do not overtighten.

6. Proceed to Step 2: Attaching the Printer.

®

.

Step 2: Attaching the Printer

1. Make sure the vehicle mount bracket is in the
unlocked position.

2. Place the printer in the vehicle mount bracket,
bottom first. Make sure it is flush against the
bracket.

3. Facing the printer, move the locking lever to the
“locked” position (from the left to the right) until it
“clicks” into the “locked” position.

Agency Approvals

Applicable Directive

• 89/336/EEC, 73/23/EEC
Applicable Standards

• EN55022 (1998)

• EN55024 (1998)

• EN60950 (1992)

Warranty

The Company warrants that Datamax-O’Neil products are free from
defects in manufacturing materials and workmanshi p f or one (1) year
from date of original purchase to Buyer/Distributor (OEMs 90 days
from the date of purchase). Batteries, cables, power supplies, and
other accessories will be warranted for ninety (90) days. Datamax­O’Neil makes no other warranties, expressed or implied, including
implied warranties of merchantability and fitness of purpose.

If you try to repair, disassemble, or change the product in any way, or
use parts not provided by Datamax-O’Neil without prior, written
authorization, all warranties are void. For complete warranty and
service information, see the Warranty Card included in your printer's
original packaging.

No Liability for Negligent Use

In no event shall Datamax-O’Neil be held liable for any damages
whatsoever (including, without limitatio ns, damages for loss of prof its,
business interruption, loss of information, or other pecuniary loss)
arising out of negligence in use and care of the product.

110209-002

PrintPAD

Vehicle Mount Bracket

Note: As an option, for security purposes, attach a
padlock to the padlock hole when the locking lever is in
the “locked” position. This will prevent others from
“unlocking” the locking lever.

COPYRIGHT © 2010, DATAMAX-O'NEIL