You will need a Phillips screwdriver to install this option.
Step A: Preparing the Printer
1. Turn ‘Off’ the power switch and unplug the AC power cord.
2. Insert the Key and unlock the Access Cover. Raise the Access Cover slightly, and then shift it
forward, off the printer.
Access Cover
3. Remove any installed ticket stock.
Key
1
4. If present, remove the Memory Module from the Module Bay. Remove the two Inside Cover Screws
and loosen the two Outside Cover Screws. Raise the Electronics Cover off the printer.
Inside Cover Screws
Electronics Cover
Module Bay
Outside Cover Screws
5. Remove the Mounting Screws securing the Cover Plate, then remove the plate.
Mounting Screws
2
Cover Plate
Mounting Screws
6. Unlock and raise the printhead. Remove the two Screws securing the Tear Input Guide, and then
remove the guide.
Screws
Tear Input Guide
3
Step B: Installing the Cutter Assembly
1. Install the Cutter Input Guide (Item 3) and secure it using the two Screws removed in Step A-6,
above.
Screws
Cutter Input Guide
2. Carefully slide the Cutter Assembly (Item 1) into the printer. Ensure that the Guide Pins on the
assembly fit into the Locator Holes in the printer, and then secure the Cutter Assembly in place using
the two Mounting Screws (Item 2).
Locator
Holes
Guide
Cutter Assembly
Pins
Mounting Screws
4
3. Remove the Screw that secures the Strain Relief to the chassis. (It is not necessary to remove the
Strain Relief or any cabling).
Screw &
Strain Relief
4. There are two cutter cables included with this kit:
Non-ROHS printers: Use Item 4 (32-2430-01)
ROHS printers: Use Item 5 (32-2628-01)
The serial label on the rear of the printer will state if the printer is ROHS compliant.
Connect the Cutter Cable from J1 of the Cutter CCA to J1 of the Main CCA..
J1, Cutter CCA
Cutter Cable
J1, Main CCA
5
5. Place the Strain Relief around the Cutter Cable, and then secure the Strain Relief to the printer using
the previously removed Screw.
Strain Relief
Screw
Main CCA
6. Replace the electronics cover. Install and tighten the two inside cover screws and then tighten the two
outside cover screws. (If removed, replace the memory module.)
7. Reconnect the interface cable(s). Plug in the AC power cord and turn ‘On’ the power switch. This
completes the installation procedure. Upon power-up, the printer will automatically sense the
presence of the Cutter, and then will cycle the Cutter 1 or 2 times. Load ticket stock and replace the
access cover. Using your software program, enable the cut function to begin using the Cutter.
6
Cutter Maintenance
Cutter maintenance is recommended after every 5,000 − 10,000 cuts, an interval that varies depending
upon the type of ticket stock being used. The need for cleaning may also be indicated when the cut
operation becomes slow or labored. To clean the cutter, proceed as follows:
CAUTION
For your safety and to avoid damaging the equipment, follow these precautions:
(1) Always turn ‘Off’ and unplug the printer before servicing the cutter;
(2) Never use a metal object on the blade; and,
(3) Keep fingers and other body parts away from the blade.
1. Turn ‘OFF’ the power switch and unplug the AC power cord. Remove the access cover.
2. Unlock the printhead latch, raise the printhead assembly and remove the ticket stock.
3. If present, remove the Memory Module from the Module Bay. Remove the two Inside Cover Screws
and loosen the two Outside Cover Screws. Raise the Electronics Cover off the printer.
Inside Cover Screws
Electronics Cover
Module Bay
Outside Cover Screws
7
4. Remove the Cutter Cable from J1 on the Cutter CCA.
J1, Cutter CCA
Cutter Cable
5. While supporting the Cutter Assembly, remove the two Mounting Screws then carefully slide out the
assembly.
Cutter Assembly
Mounting Screws
8
6. Using a soft brush or compressed air, remove all debris from inside the printer.
7. Using a soft brush or compressed air, remove all debris from the Cutter Assembly. Then, using a
cotton swab dampened with isopropyl alcohol, clean the Cutter Blade surfaces until all build-up is
removed.
8. Carefully slide the Cutter Assembly into the printer. Ensure that the Guide Pins on the assembly fit
into the Locator Holes in the printer, and then secure the cutter in place using the two Mounting
Screws.
Locator
Holes
Guide
Cutter Assembly
Pins
Mounting Screws
9. Reconnect the Cutter Cable to J1 on the Cutter CCA.
10. Replace the electronics cover. Install and tighten the two inside cover screws and then tighten the two
outside cover screws. (If removed, replace the memory module.)
11. Reconnect the interface cable(s). Plug in the AC power cord and turn ‘On’ the power switch. This
completes the cleaning procedure. Reload ticket stock.
9
Cutting Requirements
Table 1, below, lists the media requirements for use in the cutter mechanism. For a complete listing of
these requirements, see the Operator’s Manual.
Description
Inches Millimeters Inches Millimeters
Ticket Width 2.0 51 3.25 82
Ticket Weight Maximum 150 g/m2 (see note below)
The values in the following tables are only provided as a guide and should not be used as specifications
since variances within the same basis weight can occur due to the characteristics of the stock. In addition,
similar weight stocks can vary between manufacturers.
Note: The cutter may able to cut heavier ticket stock than indicated, but it is recommended that cutting
performance be verified by testing the cutter with the intended stock.
Table 2 shows the approximate media thickness in mils (thousands of an inch) relative to the metric
weight for that media.
Table 3 shows the different basis weights for the differing media types, which are “equivalent” in
weight when compared to the metric weight.
Minimum Maximum
Table 1
Metric Weight to Thickness in Mils Metric Weight to Equivalent Weight in Lbs