Page 1
OC 2/3 Swivel Lock Bracket
Mounting holes (3)
Locking lever
Swivel lock head
Swivel lock base
Locking lever
Unlocked Locked
Mounting holes (3)
Mounting dimensions
* Drill holes 7/32” diameter
* Use #10 x length 82°
machine screws (the length
is determined by the
thickness of the mounting
surface)
(220259-000)
Use the Swivel Lock Bracket for the OC 2/3 printers.
Selecting a Location
General Guidelines
• Position the bracket and/or printer with enough
room to properly open and close the printer.
• Position the bracket and/or printer so it is protected
from environmental elements such as moisture,
tools, and boxes.
• Position the bracket and/or printer in a secure area
in normal traffic patterns.
• Do not position the bracket above, near, or relative
to the driver’s position as to interfere with normal
driving operations.
• Mount the bracket and/or printer away from the
driver’s head to eliminate potential injury in the
event of an accident.
• Use only #10 x length 82° flat head screws for
mounting.
• Datamax-O’Neil does not accept liability for
improperly mounted or poorly placed swivel locks
and/or printers.
Step 1: Mounting the Swivel Lock
1. Use the swivel lock base as a template to mark the
three mounting holes on the mounting surface. For
guidelines on mounting and/or installation, see
Selecting a Location.
2. Drill the mounting holes at the marked locations.
3. Attach the bracket to the mounting surface using
#10 82° flat head screws. Thread the screws
through the swivel lock and mounting holes.
4. Tighten securely. Use locking washers or lock
tightly for vibration purposes.
5. If needed, use additional mounting hardware to
secure the bracket to the mounting surface.
6. Proceed to Step 2: Attaching the Printer.
Page 2
OC 2/3
110218-002
Swivel Lock Bracket
Step 2: Attaching the Printer
1. Make sure the swivel mount bracket is in the
unlocked position.
2. Place the printer’s swivel mount block over the
unlocked swivel lock bracket.
3. Facing the printer, move the locking lever to the
“locked” position (from the left to the right) until it
“clicks” into the “locked” position.
Agency Approvals
Applicable Directive
• 89/336/EEC, 73/23/EEC
Applicable Standards
• EN55022 (1998)
• EN55024 (1998)
• EN60950 (1992)
Warranty
The Company warrants that Datamax-O’Neil products are free from
defects in manufacturing materials and workmanshi p f or one (1) year
from date of original purchase to Buyer/Distributor (OEMs 90 days
from the date of purchase). Batteries, cables, power supplies, and
other accessories will be warranted for ninety (90) days. DatamaxO’Neil makes no other warranties, expressed or implied, including
implied warranties of merchantability and fitness of purpose.
If you try to repair, disassemble, or change the product in any way, or
use parts not provided by Datamax-O’Neil without prior, written
authorization, all warranties are void. For complete warranty and
service information, see the Warranty Card included in your printer's
original packaging.
No Liability for Negligent Use
In no event shall Datamax-O’Neil be held liable for any damages
whatsoever (including, without limitatio ns, damages for loss of prof its,
business interruption, loss of information, or other pecuniary loss)
arising out of negligence in use and care of the product.
Note: If you would like to charge the printer while it is
attached to the swivel lock bracket, plug the power
connector (right angle cable only) into the printer, then
attach the printer to the bracket. Make sure the
charging cord is hanging straight down and does not
interfere with the swivel lock bracket.
COPYRIGHT © 2010, DATAMAX-O'NEIL
Loading...