User Manual
User Manual
Table of Contents
1. Introduction
2. Installation
2.1 Minimum Requirements
2.2 Installation Proc ess
3. Getting Started
3.1 Graphical User Interface
3.2 File Storage
3.3 Printer Information
3.4 Printer Status
4. Operation
4.1 Webmenu
4.2 Telnet
4.3 FTP
4.4 Network Settings
4.5 Options
4.6 Clear
4.7 Clear Al l
4.8 Upgrade
5. Program Menu
5.1 File
5.2 Edit
5.3.Tools
5.4 Help
User Manual
Conditions
© Copyright Datamax-O’Neil 2010
Thank you for choosing this product for your printer
monitoring and configuration needs.
Manufacturer Address:
Datamax-O’Neil Corporation
4501 Parkway Commerce Boulevard
Orlando, Florida USA 32808
Phone (407) 578-8007
Fax (407) 578-8377
http://www.datamax-oneil.com
Conditions
Datamax-O’Neil reserves the right to change
specifications in both the text and illustrations without prior
notice. The contents of the publication may not be copied,
neither wholly nor in part, without permission from
Datamax-O’Neil.
Datamax-O’Neil cannot be held responsible for any
program faults or data loss caused by this software,
including the cost of recovering from such situations.
Art. Number: 318944
User Manual
1. Introduction
Datamax-O’Neil NetCenter is the perfect tool for finding,
managing and supervising Datamax-O’Neil printers connected
to the same local area network (LAN). All printers are
automatically detected and displayed in a list in the intuitive
graphical user interface. The list shows network settings,
firmware version, serial number and current status for each
printer. This makes it easy to see which printers are online and
ready, when paper or ribbon needs to be changed, to configure
printer network settings and manage firmware upgrades. From
the list of printers NetCenter also provides easy access to each
printer by the use of the most common network protocols.
NetCenter is intended for network administrators who manage
Datamax-O’Neil printers on a LAN.
User Manual
2. Installation
This section describes how to install and set up Datamax-O’Neil
NetCenter once the minimum requirements have been complied.
2.1 Minimum Requirements
To be able to use NetCenter the following computer configuration
is needed (mainly dependent on the requirements for the
Microsoft .NET Framework).
Processor Intel Pentium class, 90 MHz or
higher.
Operating System Microsoft Windows
XP/2000/NT4/ME/98
(Note: Windows NT 4.0 Terminal
Server is not supported).
RAM Memory 32 MB (96MB or more
recommended).
Hard Disk 5 MB of free space.
Additional Software Microsoft .NET Framework version
1.0 or later.
Target Environment Datamax-O’Neil Nova and Compact
printers using processor board with
CPU-5 or later and printer firmware
version 5.1.0 or later.
The recommended way to download the Microsoft .NET
Framework is by using Windows Update located at
http://www.windowsupdate.com
Visit http://www.microsoft.com/net/basics/framework.asp
more information about the .NET Framework.
.
for
2.2 Installation Process
The distribution of NetCenter consists of a single executable file.
Simply run it and follow the instructions shown by the setup
wizard. By default, the software is installed on the same drive as
the operating system with its program files located in the
Program Files/Imaje/NetCenter directory. A different path can be
specified if required.
User Manual
3. Getting Started
This section explains the Datamax-O’Neil NetCenter user interface.
3.1 Graphical User Interface
The graphical user interface of NetCenter consists of a window displaying all MPClass Datamax-O’Neil printers in a list and a toolbar containing the available
operations for each printer in that list. The available operations can also be
accessed through the NetCenter program menu. At the bottom of the NetCenter
window there is a status field, which shows how many printers that are connected,
total number of printers and the number of printers currently non-operational (e.g.
out of paper). See figure 1 for an overview of the graphical user interface.
Figure 1. Screenshot of NetCenter.
From this view it is easy to select a printer and perform any of the available
operations, as described in section 4 - Operation.
3.1.1 First Start
The first time NetCenter is started the list of printers is empty and a
broadcast requesting printer information is sent to the network. All DatamaxO’Neil printers supporting NetCenter will then answer this broadcast and
their network properties are stored in the list. It should only take a few
seconds for the list to be populated.
Note : Compact and Nova models using Printcore version 5.1.7
or older requires a valid IP address to be set before
NetCenter can find it.
User Manual
3. Getting Started
3.1.2 Column Customization
The size and order of the columns can be customized to fit your
needs. To change the size of a column, simply click and drag the
separator line between the column headers to a suitable position
and release the mouse button. The order of the columns can be
changed in the same way, simply click on a column header and
drag it to a suitable position and release the mouse button.
3.1.3 List Sorting
NetCenter adds new entries at the bottom of the displayed printer
list and thus the list is originally sorted by how fast each printer
responds. The sorting order can, however, be changed by clicking
on the column headers at the top of the list. The column is sorted
either by number or alphabetically, depending on column content.
The sorting order of the column changes for each click on the
column header, e.g. from ascending to descending and vice versa.
A small arrow is displayed in the column header to indicate the
current sorting order.
3.2 File Storage
The list of printers found is stored in a file called printerlist when
NetCenter exits. The printerlist file follows the XML v1.0 standard,
which makes it easy to import and use it in any third-party software
for displaying the list of Datamax-O’Neil printers found in your
network.
The next time NetCenter starts, the displayed list of printers will be
read from the printerlist file to be able to determine if a printer is
disconnected, that is, exists in the file but is currently not
responding. New printers added to the LAN will automatically be
detected and added to the displayed list, then stored among the
rest of the printers in the printerlist file when NetCenter exits.
The printerlist file is located in Isolated Storage in order to comply
with the new Microsoft guideline. This will also automatically grant
proper access rights to the file and make future NetCenter
upgrades very convenient. The path to the printerlist file depends
on the operating system used.
See the Microsoft website http://msdn.microsoft.com/library/en-
us/cpguide/html/cpconintroductiontoisolatedstorage.asp for more
information on Isolated Storage.
User Manual
3. Getting Started
3.3 Printer Information
For each printer in the displayed list, the following information is
available:
• Host name
• Printer model
• Firmware version
• Serial number
• MAC address
• DHCP setting
• IP Address
• IP Mask
• Gateway
• Status
3.4 Printer Status
The list of printers changes its appearance depending on the current
status of each printer. This makes it easy to find a printer not
operating or disconnected. The following list displays all possible
status states that might occur.
Ready Printer connected and operational
Printer restarted Printer restarted, will change status at
next broadcast. See options for more
details about broadcast settings.
Disconnected Printer disconnected. The printer has
stopped answering to broadcast calls.
Upgrading… Printer firmware is being upgraded. See
operations for more information about
printer firmware upgrading.
Error states All other states are regarded as error
states (by NetCenter). Refer to the
Labelpoint manual for more information
about the system status that can occur
During normal operation, when a printer is connected and ready or
restarted, the list entry is displayed in default text colour on a default
window background colour (e.g. black text on white background
when using Windows default settings). Printer offline is displayed in
inactive text colour on a default window background.
for each printer model.
User Manual
3. Getting Started
Note that NetCenter uses system default colour settings, which may
vary depending on the current colour theme used on your computer.
Since there is no ‘alarm’ colour or such defined among Windows
default colours, the only exception from using Windows default
colours is the printer error states, which always are displayed as
white text on a red background.
User Manual
4. Operation
This section explains all operations that can be made on a
selected printer in the list. The available operations can be
accessed in three different ways, as shown below.
Note : Some of the operations might be disabled, the
available operations depend on the status of the
selected printer or printers.
1) By using Edit and Tools from the program menu
2) by pressing the toolbar icons
3) or by selecting from the context menu, which appears when
right-clicking in the list.
The following sections will describe in detail how each of the
available operations work.
4.1 Webmenu
Opens your system’s default web browser and automatically
connects to the selected printer’s web server. The webmenu will
automatically be displayed in your web browser when the
connection has been made to the printer. Refer to the Labelpoint
manual for more information about how to use the webmenu.
User Manual
4. Operation
4.2 Telnet
Opens the standard Windows Telnet client and connects to the
selected printer on its Telnet port (port 23). From here it is
possible to send Labelpoint commands.
If the selected printer already is using another port to receive
Labelpoint commands then the printer will not listen on the Telnet
port for Labelpoint commands until the Labelpoint command “!C”
is sent to the already active port. Refer to the Labelpoint manual
for more information about port handling and Labelpoint
commands.
4.3 FTP
This will open your system’s default FTP client and automatically
connect to the selected printer’s FTP server. Refer to the
Labelpoint manual for more information about file management.
Note : The embedded FTP server in the printers does
not support passive mode. Be sure to use active mode
when accessing the FTP server.
User Manual
4. Operation
4.4 Network Settings
Opens a dialog window containing all network related printer
settings. A screenshot of the dialog window is shown in figure 2.
Tip : The network settings can easily be accessed by
double clicking in the printer list.
Figure 2. Network settings dialog
From the dialog window it is easy to change the current settings for
host name, domain, TCP keepalive, DHCP and IP settings. When
finished, press the ‘OK’ button. The changes will then be sent to the
printer and a message box will appear asking if you want to restart
the printer.
Note : The new settings will not be applied until the
printer is restarted.
User Manual
4. Operation
4.5 Options
NetCenter options can only be accessed through the program menu
and will open a small dialog window as shown in figure 3.
Figure 3. Options dialog
There are two available options; network adapter and broadcast
interval time.
4.5.1 Network Adapter
If a computer is equipped with more than one network adapter this
option makes it possible to select the preferred one from a list of
available adapters. The adapters are found automatically and
displayed in the list along with its IP address to make it easier to know
what adapter to choose. Note that a restart of NetCenter is required if
the network adapter is changed.
4.5.2 Broadcast Interval Time
The broadcast interval time decides how often a broadcast is made
from the NetCenter PC to the LAN to check for Datamax-O’Neil
printers. If many printers are connected to the same LAN a low value
might create unnecessary network traffic. As a hint to determine a
good value it can be mentioned that both the broadcast and response
packets fit inside a single Ethernet frame, so the traffic load generated
is actually quite small and increases linearly with the number of
printers on the LAN. The default interval time is two seconds.
Note : The list of printers can always be updated
manually by pressing the Refresh button located on the
toolbar. This is especially useful when a high interval
value is used.
User Manual
4. Operation
4.6 Clear
Removes the selected printer(s) from the list.
4.7 Clear All
Removes all printers from the list, no selection can be made.
4.8 Upgrade
Opens a dialog window where a printer firmware configuration file can be selected,
see figure 4. To be able to upgrade any printer(s) two requirements must be fulfilled.
First, a NetCenter firmware bundle is needed, which can be downloaded from the
Datamax-O’Neil website at www.datamax-oneil.com
must be connected and have a valid IP address.
Note : The option to upgrade printer firmware is supported by Compact
and Nova printers using Printcore 5.1.19 or later.
. Second, all printers selected
Figure 4. Firmware file dialog
User Manual
4. Operation
The default file to select in the file dialog is firmware.xml. When
opened, NetCenter automatically selects the matching binary
file(s) from the fimware bundle for the printer(s) selected. It is
thus possible to select any combination of printers and upgrade
them simultaneously as long as the printer firmware exists in the
firmware bundle. Before starting the actual upgrade NetCenter
will prompt the user to inform that an upgrade is about to take
place.
During upgrade it is very important not to turn off the power to
the printer(s) since an interrupted upgrade might corrupt the
printer firmware.
After an upgrade all selected printers are automatically restarted.
User Manual
5. Program Menu
This section explains all available options in the NetCenter
program menu.
5.1 File
The File menu contains options for printing the list of printers
currently found. The information on the printout is the same as
described in section 3.2 - Printer Information except for printer
status, which is not shown.
Print Opens a print dialog
Print Preview Opens a print preview dialog.
Page Setup Opens a page setup dialog. Note that page
orientation is set to landscape to be able to
fit all printer information.
Exit Exits NetCenter
5.2 Edit
The Edit menu contains options for changing the settings of a
selected printer and for removing items from the list.
Network
Settings
Clear All Removes all printers from the list
Opens a new dialog containing the selected
printer’s network settings. See section 4.4 –
Network Settings for more information.
Clear Removes selected printer from list
User Manual
5. Program Menu
5.3 Tools
From this menu all operations are accessed.
Access
Webmenu
Start Telnet
Session
Start FTP
Serssion
Upgrade
Firmware
Options Opens a new dialog with NetCenter
See section 4.1 - Webmenu for more
information.
See section 4.2 - Telnet for more
information.
See section 4.3 - FTP for more information.
See section 4.8 – Upgrade for more
information.
options. See section 4.5 - Options for more
information.
5.4 Help
Contains only the About option.
About Opens a new dialog containing information
about current NetCenter version and
contact information to Datamax-O’Neil.
Loading...