Datamax-O'Neil microFlash 4t-4te External Charger Swivel Lock User Manual

MF4 External Charger Swivel Lock
(220226-003)

Foot

Figure 1

Swivel
Lock

AC
Adapter

AC
Adapter
Cradle

Parts List

(1) MF4 External Swivel Lock Depot Charger
(1) High capacity AC adapter
(1) Grounded AC power cord
(7) #10 x 1¼” wood screws (not shown)
(7) #10 flat washers (not shown)
#8 - #10 toggle bolts [not included; length to be

determined by the user

Note: Use #10 x 1¼” wood screws to mount

rging dock to wood surfaces only. The

cha
#10 x 1¼” wood screws cannot be used to mount
the depot charger to any other type of surface.

Use #8 - #10 toggle bolts if you are mounting the
depot charger to drywall.

Grounded
AC Power
Supply
Cord

the

DC
Power
Jack

Guidelines

General Guidelines

• The MF4 Depot Charger is designed to be used as a
desktop or wall mounted unit.

• Keep the charging dock in a cool, dry place, away from
direct sunlight, high temperature, and moisture.

• The depot charger takes approximately 3-4 hours to
charge each printer. If multiple printers are attached, the
charge time remains at approximately 3-4 hours per
printer; however, charge times may vary.

• The depot charger is not recommended for use with the
MF2t Smart CardReader (SCR) or MF4t Smart
CardReader (SCR) printers.

• When connected to the depot charger, the printer(s) may
not print.

Safety Guidelines

• Do not short the contacts.
Use only an Datamax-

•

• Position the depot charger with enough room to properly

open and close the printer(s); position the depot charger
so it is protected from environmental elements such as
moisture, tools, and boxes; and position the depot
charger in a secure area in normal traffic patterns.

• Do not operate the depot charger if it appears damaged.

• To reduce risk of electric shock, unplug the depot charger

before cleaning.

• Batteries become warm to the touch during charging. If
the battery becomes too hot to touch, discontinue
charging and contact Datamax-O'Nei

• Use

of any charger or battery not approved by
Datamax-O'Neil for use with their printers
could cause damage to the batteries or printer and will
void the warranty.

• Datamax-O'Neil does not accept liability for
improperly mounted or poorly placed printers and/or
depot charger.

O'Neil approved power supply.

l.

Mounting the Depot Charger

If the depot charger will be mounted on a vertical
surface or on a wall, use the following procedure to
mount the charging dock:

1. Remove rubber bumpers from the
feet's and AC Adapter cradle.

2. Locate the mounting holes. There are two
mounting holes on either end of the
(Figure 3) and two mounting holes in the middle
of the

depot charger (Figure 4).

Figure 3

3. Use the

depot charger as a template to mark the

Figure 4

mounting holes on the mounting surface
(Figure 5). For information on mounting, see the
Guidelines in the previous section.

Figure 5

at

4. Drill the mounting holes

the marked locations.

Warning: Use caution when drilling the
mounting holes and when mounting the

charger

5. Attach the

onto a wall.

depot charger to the mounting surface

as follows:
Drywall Surface: Use #8 - #10 toggle bolts (not

included).
Wood Surface: Use #10 x ¼” wood screws.

#10 x ¼” wood screws cannot be used on any
other type of surface.

6. Verify the

depot charger is level.

7. Thread the screws through the washers,

charger

, and mounting holes and tighten securely.

depot charger

depot charger

depot

depot

8. Proceed to Attaching the Power Supply.

Attaching the Power Supply

Use the following procedure to attach the power
supply to the
already attached to the
Attaching the Printer(s).

1. Insert the AC Adapter into the
Adapter cradle (Figure 6).

2. Plug the AC Adapter's connector into the

charger's power supply cable socket (Figure 7).

3. Plug the Grounded AC Adapter’s connector into
the AC Adapter's socket (located on the AC
Adapter cradle). Verify the 3-prongs of the
Grounded AC Adapter's conn
Adapter's socket (Figure 7).

depot charger. If the power supply is

depot charger, proceed to

depot charger's AC

depot

match the AC

ector

Attaching the Printer(s)

1. Place the printer's swivel mount block over the
unlocked swivel lock bracket (Figure 9).

2. Facing the printer, move the swivel lock lever from
left to right until it “clicks” into the locked position
(Figure 10).

110164-002

MICROFLASH 4T

External Charger Swivel Lock

AC Adapter's connector

Depot charger's power supply
cable socket

Depot charger's AC Adapter
cradle

AC Adapter

Figure 6

AC Adapter 3-prong socket
Grounded AC Adapter

Figure 7

4. Plug the Grounded AC Adapter cord to an outlet.

5. Plug in the external charger at each location
(Figure 8).

Figure 9

Figure10

Warranty

The Company warrants that Datamax-O’Neil, products are free
from defects in manufacturing materials and workmanship for one (1)
year from date of original purchase to Buyer/Distributor (OEMs 90 days from
the date of purchase). Batteries, cables, power supplies, and other
accessories will be warranted for ninety (90) days. Datamax-O’Neil
makes no other warranties, expressed or implied, including
implied warranties o
If you try to repair, disassemble, or change the product in any way, or use
parts not provided by Datamax-O’Neil without prior, written authorization, all
warranties are void. For complete warranty and service information, see the
Warranty Card included in your printer's original packaging.

ntability and fitness of purpose.

f mercha

No Liability for Negligent Use

In no event shall Datamax-O’Neil be held liable for any damages
whatsoever (including, without limitations, damages for loss of
profits, business interruption, loss of information, or other pecuniary loss)
arising out of negligence in use and care of the product.

Figure 8

Note: Make sure you regularly clean the

charging contact points on your printer's case
to ensure your printer's batteries are properly
charged and avoid damage to printer or
charger. To clean the charging contact points,
unplug the charger from the wall and clean
using alcohol and a clean rag.