Datamation Systems CMS208-DS-D820 User Manual

Model CMS208-DS-D820
DS-8BY-BC-820
SPAN inc warrants this product to be free of faults due to materials and workmanship for a period of one year from date of purchase.
In case of problems or concerns please contact Datamation Systems, Inc.
For indoor use only
WARNING:
Charge only Dell™ model D820, D830 & D831
batteries.
Regulatory Approvals
Span part no. CMS208-100
This equipment complies with:
UL1012
USA - FCC Part 15 Subpart B Class A limit Rules
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.
The user is cautioned that changes and modifications made to the equipment without approval of the manufacturer could void the user's authority to operate this
equipment.
Battery Chargers and
Made in USA
SYSTEMS
Owner Operating
Instructions for
Model CMS208-DS-D820
EIGHT POCKET
FAST BATTERY CHARGER
for
DELL™ MODEL
D820, D830 & D831
Max. input: 120 VAC 600 Watts
Max. output: 22 VDC max @ 22 A DC
Listed
24ZM
Battery
Charger
Dell Computer part number
DS-8BY-BC-820
Manufactured by Span, Inc. for Datamation Systems, Inc.
all rights reserved.
Dell is a trademark of Dell, Inc.
Model CMS208-DS-D820
Dell Computer p/n DS-8BY-BC-820
IMPORTANT SAFETY INSTRUCTIONS
1. SAVE THESE INSTRUCTIONS - This manual contains important
safety and operating instructions for battery charger
2. Before using battery charger, read all instructions and cautionary markings on battery, battery charger, and computer.
3. CAUTION - To reduce risk of injury, charge only Dell™ model D820, D830 and D831 batteries. Other types of batteries may burst causing personal injury and damage.
model CMS208-DS-D820.
Description
This is a fast battery charger for Dell™ model D820, D830 & D831 batteries only. Do not attempt to use this charger with any other battery type. Eight battery charging pockets are provided to rapidly service this specific battery series. Working from a common line power outlet, a
maximum 600 Watt power supply mounted internally provides all the necessary power for charging these batteries as described below.
Preparation for Use
Place the charger unit on a sturdy horizontal surface with its line cord exiting the unit from the back side (the side away from the user). The power switch will be on the side nearest the user. Plug the AC line cord into a standard 115 VAC socket. The cord serves as the disconnect device. The line outlet socket must be near the unit and easily accessible. The circuit should be qualified to handle at least 15 Amps and be relatively free of other heavy loads while the charger is operating.
Operation and User Interface
Press the rocker switch in to turn the charger power supply on. If line power is present, the power indicator will illuminate steady green and the power supply fan will become active producing an audible sound (this is normal). Place batteries into charger pockets in any position or sequence being careful to orient the batteries so the connectors line up, then gently pressing them down all the way into the pockets. Each of 4 pairs (front/rear) of pockets operates independently charging batteries sequentially based on which battery was inserted first. When a battery is seated properly in a pocket its corresponding LED will illuminate solid yellow if the battery is the first of the pair to be inserted, or will blink yellow if the battery is the second of the pair to be inserted. When a pocket has finished charging, its LED will turn solid green and the second pocket of that pair will begin charging, if necessary. If a fully charged battery is
inserted, the pocket will indicate charging for a short time, then terminate with the indicator showing solid green. See below for a complete list of status indicators. Batteries may remain in the pockets indefinately or be removed at any time without damage. It normally takes 4 to 6 hours to fully charge a battery.
Smart Battery Calibration
Dell™ series batteries mentioned above are 'smart'. They have an internal controller that interacts with the charger to report charge status and other information. Through normal use errors in the estimated charge level will accumulate and cause false readings. These errors can be eliminated by recalibrating the battery's internal controller. This charger has the facility to calibrate batteries placed in the left-most front pocket. To trigger calibration of a battery in this pocket, momentarily press the front-panel calibrate switch. The start of a calibration cycle will be confirmed by a blinking yellow/green indicator. The calibration cycle may take up to 9 hours. When finished the battery will be fully charged and the controller will be calibrated to that state.
Charger Status Indicators
A tri-color LED indicator is located below each pocket to indicate charge status of the battery in that pocket:
Indication
solid yellow
solid green
blinking red
blinking yellow / green
blinking green
blinking yellow
Meaning
no battery present
off
battery charging battery charged and ready
charging error - charge cycle terminated (contact battery supplier)
calibration mode calibration finished charge pending
Specifications
input Voltage: 100 to 120VAC 60 Hz 1 phase input power: 7 Amps AC max. Max. output voltage: 22 VDC max. Max. output current: 2.0 Amps max. per pocket 22 A DC max total operating temp: 0 to 45 C° battery types: Dell™ Battery Model# D820, D830,D831 size: 17" x 17.25" x 6.25" weight: 25 lbs. less batteries
Warning
Charge only Dell™ model D820, D830 & D831 batteries.
June 20, 2007
Loading...