Datalogic TC1100 User Manual

EAN/UPC disable AA0

68

(

)

(

)

(

)

(

)

EAN 8/EAN 13/UPC A/UPC E enable AA1

EAN 8/EAN 13 enable AA3

UPC A/UPC E enable AA4

EAN 8 enable AAG0

EAN 13 enable AAH0

UPC A enable AAI0

UPC E enable AAJ0

Code 39 disable AB0
Code 39 Standard enable AB11xxyy

Code 39Full ASCII enable AB21xxyy

Code 2/5 family disable AC0
Interleaved 2/5 enable AC11xxyy

Normal 2/5 5 bars enable AC21xxyy

Industrial 2/5 (IATA) enable AC31xxyy

Matrix 2/5 3 bars enable AC41xxyy

Codabar family disable AD0
Codabar standard enable AD111xxyy

Code 128 family disable AI0

Code 128 enable AI11 xxyy control without transmission of check digit
EAN 128 enable AI21 xxyy control without transmission of check digit
Code Length AILxxyy

Code 93 family disable AK0
Code 93 enable AK1 xxyy control without transmission of check digit
PDF417 disable AR0
PDF417 enable AR1
Pharmacode disable AQ0

Pharmacode enable AQ1xxyy

Overflow ratio AQAzz

xxyy = ASCII numbers that define:

AA5
AA8

AAK
AAL
AA6

AAM
AAN
AA7

AAG1

AAH1

AAI1

AAJ1

AB12xxyy
AB13xxyy

AB22xxyy

AC12xxyy
AC13xxyy

AC22xxyy
AC23xxyy

AC32xxyy
AC33xxyy

AC42xxyy
AC43xxyy

AD112xxyy
AD121xxyy
AD122xxyy
AD212xxyy

AQ2xxyy

without ADD ON
with ADD ON
with and without ADD ON
without ADD ON
with ADD ON 2 ONLY
with ADD ON 5 ONLY
with ADD ON 2 AND 5
without ADD ON
with ADD ON 2 ONLY
with ADD ON 5 ONLY
with ADD ON 2 AND 5
check digit transmission disable
check digit transmission enable
check digit transmission disable
check digit transmission enable
check digit transmission disable
check digit transmission enable
check digit transmission disable
check digit transmission enable

no check digit control
check digit control and transmission
check digit control without transmission
no check digit control
check digit control and transmission

no check digit control
check digit control and transmission
check digit control without transmission
no check digit control
check digit control and transmission
check digit control without transmission
no check digit control
check digit control and transmission
check digit control without transmission
no check digit control
check digit control and transmission
check digit control without transmission

no start/stop character equality control - nor transmission
no start/stop character equality control but transmission
start/stop character equality control but no transmission
start/stop character equality control and transmission
ABC Codabar no start/stop character equality control but transmission

forward code tx direction
reverse code tx direction

xx = min. acceptable code length yy = max. acceptable code length zz = overflow ratio value
The minimum code length must always be less than or equal to the maximum.

For more detailed information on the TC1100 programmability and complete parameter list, please refer to the
TC1100 Reference Manual.

N24

CODE SELECTION

821000606 (Rev. H)

TC1100

CCD Scan Engine
Quick Guide

The TC1100 is a linear CCD Scan Engine for OEM applications. It is available in two different versions:

Model Description Order Number

TC1100-0100 CCD scan engine for linear codes 939501000
TC1100-0200 CCD scan engine for linear and PDF417 939501010

Technical Specifications

Power supply
Consumption 1.5 W
Interfaces RS232, WEDGE, PEN Emulation
Max Scans/sec 270
Max resolution 0,076mm (3mils)
Readable codes:

Default Configuration

Power Save 270 scans/sec, sleep disabled, standby disabled
Reading Parameters On-Line
Code Selection

Enabled codes

(Only TC1100-0200)

Data Format Code ID disabled, Header = <STX>, Terminator = <CR> <LF>, no Field Adjustment, Code

Decoding Parameters Ink spread enabled, overflow control enabled, interdigit control enabled, Puzzle Solver™

Enabled interface RS232, 9600, N, 8, 1, no handshaking, ACK/NAK disabled, RX timeout 100 ms, FIFO

Reading Diagrams

0 20 40 60 80 100 120 140 160 180 200 220 240 260 280 300 320

160

140

120

100

80

0.20 mm

60

40

20

0

-20

-40

-60

-80

-100

-120

0.13 mm

-140

5 mils

-160

Reading Diagram TC1100-0100 (code 39) Reading Diagram TC1100-0200 (PDF417)

0.20 mm

5 Vdc ± 5%

EAN/UPC, Code 39, 2/5 family, Codabar, Code 128, EAN 128, ISBT 128, Code 93,
pharmaceutical codes, Delta IBM, Code 16K, Code 49, (Telepen, MSI/Plessey, Pharmacode
only TC1100-0100), (Codablock-A, Codablock-F Std, Codablock-F EAN, PDF417 only
TC1100-0200)

• Interleaved 2 of 5: Check Digit transmitted, length: min 4, max 99

• Code EAN8, EAN13, UPCA, UPCB: without ADD ON, Check Digit transmitted, no conversions

• Code 39: length: min 1, max 99

• Code 128: Check Digit not transmitted, length: min 1, max 99

• PDF417

length TX disabled, character replacement disabled, No Read Character = <CAN>

disabled, decoding safety = 1 read

enabled, inter-character delay disabled

0 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170 180

90

80

70

60

50

40

30

20

10

0

10

-

-20

-30

-40

-50

-60

-70

-80

-90

8 mils

0.30 mm

12 mils

0.50 mm

20 mils

0.17 mm

(6.6 mils)

0.25 mm

(10 mils)

0.38 mm

(15 mils)

Electrical Connections

J1

1 SGND Serial Ground
2 OUT ­3 OUT+
4 EXT BEEPER External beeper connection
5 CTS Clear to send
6 RX Reception
7 RTS Request to send
8 TX Transmission

J2

1 VCC+ +5Vdc
2 GND GND
3 CLKOUT
4 DATAOUT
5 DATAIN_WAND
6 CLKIN
7 EXT TRIG+
8 EXT TRIG-

See Figure 1

See Figure 2

Physical Dimensions

Width 63 mm 2.48 inches
Length 60.5 mm 2.38 inches
Height 27 mm 1.06 inches

Ø2.7

[Ø0.11] n°4

40.5

[1.59]

63

[2.48]

Connectors:

HIROSE

Mod. DF13-8p-1.25V

1

J1

1

J2

[0.10]

18

[0.71]

Led Status

Led2 ON = Power supply ON
Led2 OFF= Power supply OFF

Led1 ON=

Led1 OFF= Miss read

Good read (the led will remain
ON until status changes)

mm

[ in.]

[1.97]

Led2 Led1

2.5

[0.10]

57

[2.24]

28.5

[1.12]

Horizontal Optical Axis

63

[2.48]

2.5

[0.10]

25.7

[1.01]

Return to RS232 Interface

TC1100

J1

3

2

USER INTERFACE

OUT +

OUT -

Vext 40 Vdc max

Ì$+CP0$-$Î

Veritcal Optical Axis

12.2

[0.48]

Figure 1 - Output Connection (Good Read). Example NPN

For WEDGE Users

Vext

TC1100

+ 5V

J2

7

8

Vext

EXT TRIG+

EXT TRIG-

30 Vdc max.

EXTERNAL TRIGGER

V

Signal

TC1100 EXTERNAL TRIGGER

+ 5V

J2

7

8

EXT TRIG+

EXT TRIG-

30 Vdc max.

V

Signal

Ground

Input NPN command using external power Input PNP command using external power

J2

Vcc 5Vdc

+ 5V

1

EXT TRIG+

7

8

EXT TRIG-

2

GND

EXTERNAL TRIGGERTC1100

V

Ground

Signal

+ 5V

J2

Vcc 5Vdc

1

7

EXT TRIG+

8

2

Input NPN command using TC1100 power Input PNP command using TC1100 power

Figure 2 - Trigger Connections

2.5

50

60.5

[2.38]

Basic Commands for TC1100

The TC1100 default configuration can be changed by receiving commands through the RS232 Interface. The command syntax
is given below with an example.

Command syntax

$+ Command(s) $- <CR> the new setting will be definitive (stored in FLASH EPROM)

Example:

Enter configuration environment

Serial On-Line

Commands:

Operating Mode

Baud Rate = 19200

Multiple command programming sequence:

BK0 $- CR

$+

AC410132CD7

Matrix 2/5 3 bars: no check digit,

variable length code from 1 to 32 characters

Carriage return character (0D Hex.)

Exit and save new configuration

EXT TRIG-

GND

EXTERNAL TRIGGERTC1100

V

Signal

Ground

OPERATING MODES

On-line BK1
Serial On-line BK0
Automatic BK3
Automatic / Lighting System Standby BK2
To enter in Test mode #+Dstat1<CR> (does not require $+ or $-)
To exit Test mode #+Dstat0<CR> (does not require $+ or $-)

GENERAL FEATURES

RS232 interface selection CP0
RS232 Baud Rate CD0 for 150 Baud up to CD8 for 38400 Baud
WEDGE AT CP500
WEDGE Notebook CP505
Keyboard Nationality FJ7 Belgian

CCD Scan Rate BT0 67 scans/sec

Puzzle Solver AU1 enable AU0 disable
Ink Spread AX1 enable AX0 disable
Decoding safety ED0 1 read

To restore the default configuration $+$*<CR> (does not require $-)
To get configuration from the reader $+$& <CR> (does not require $-)

FJ4 English
FJ2 French
FJ3 German

BT1 135 scans/sec
BT2 270 scans/sec

ED1 2 reads

FJ1 Italian
FJ6 Spanish
FJ5 Swedish
FJ0 USA

ED2 3 reads
ED3 4 reads