Datalogic SG-PSB Series, SG-PSB 600, SG-PSB 1000, SG-PSB 1200, SG-PSB 1900 Instruction Manual

SG-PSB

Safety light curtain protective armor stand

Instruction Manual

Fig. A

826000200 (Rev.00)

SG-PSB INSTRUCTION MANUAL

2

GENERAL INFORMATION

The SG – PSB accessory is a guard, which comprises a drawn aluminium column and a
steel base. The base is made of two plates. Their inclination can be adjusted by means of
three dowels and their angular position can be adjusted through 3 rough adjustment slots
and 3 fine adjustments slots. Thanks to its single drawn section, available in a range of
different lengths, and to its multi-purpose grooves, this accessory can contain inside it all the
models of the SE, SG2, SG4, SE Body and SG Body series.

CHARACTERISTICS

 Protects the light curtain mounted inside it from accidental collisions;
 Single painted drawn aluminium section in different lengths, suitable for all heights of the

following series: SE, SG2, SG4 (150 – 1800 mm), SE Body and SG Body (2, 3 and 4­beam);

 Sturdy steel base made of 2 plates with angle reference marks, dowels for adjustment of

the vertical axis and slots for angular position adjustment;

 Spheric level to facilitate adjustment of the vertical axis;
 Double rear groove for installation of external muting sensor supports.

TYPICAL APPLICATIONS

Use of the SG-PSB accessory is recommended in work environments typical of the material
handling market, where forklift trucks, AGVs or other vehicles move freely within the plant
and may collide with the safety light curtains.

Fig. 1

SG-PSB INSTRUCTION MANUAL

3

NOTES

If a body protection is being used, compliance with the EN 999 standard
'Safety of machinery - Positioning of safeguards with respect to the
approach speeds of parts of the human body' is required.

MECHANICAL MOUNTING

The SG-PSB guard can house a number of different products. For this reason, 5 different
bracket kits are available:

 ST-PS4-SG/SE (95ASE1750): for the installation of light curtains of the SG/SE/SG Body

Compact series, finger/hand protection, protected height 150÷1050mm and body
protection, protected height 500, 800, 900mm;

 ST-PS6-SG/SE (95ASE1760): for the installation of light curtains of the SG/SE/SG Body

Compact series, finger/hand protection, protected height 1200÷1800mm and body
protected height 1200mm;

 ST-PS4-SG Body (95ASE1730): for the installation of light curtains of the SG Body Big

series, body protection, protected height 500, 800, 900mm;

 ST-PS6-SG Body (95ASE1740): for the installation of light curtains of the SG Body Big

series, body protection, protected height 1200mm;

 ST-PS-DM (95ASE1770): for the installation of deviating mirrors SG-DM.

An extra plate may be installed on the accessory, to compensate for the effects of collisions,
vibrations and uneven floor surfaces:

 SG-P (95ASE2290): for the installation of a double plate with compensation springs.

The instructions for the installation of these accessory kits can be found below:

SG2, SG4-B, SE, SG BODY COMPACT SERIES MOUNTING

With the help of the ST-PS4-SG/SE kit, for product versions from 150 to 1050 mm or of the
ST-PS6-SG/SE kit, for product versions from 1200 to 1800 mm, build sub-assemblies as
shown in Fig. 2 then insert and fasten them to the grooves on the guard. Do not tighten
completely the M5 nut under the bracket (in the following example a SG2/4 base profile is
used).

M5 nut