Datalogic SG-DM Instruction Manual

SG-DM

Deviating Mirrors

Instruction Manual

Figure A

821001930 (Rev.00)

SG-DM INSTRUCTION MANUAL

NOTES AND WARNINGS

 To guarantee the correct functioning of the safety light curtains, we recommend the use

of no more than three deviating mirrors to deviate the beam along the optic path.

 Each mirror used decreases the operating range of the safety light curtain by 15%, 20%,

25%. Apply a correction factor of 85% using one mirror, 65% using two mirrors, 50% for
three mirrors.

 To maintain the correct functioning of the system, we advise to periodically clean the

mirror surface using a damp non-abrasive cloth. The cleaning frequency depends on the
system’s surrounding environment.

 The mirror length has to be at least 100 mm superior to the length of the light curtain’s

protected area.

 The mirror has to be mounted in such a manner that its axis (horizontal and vertical)

coincide with the corresponding safety device axis.

 The mirror has to be solidly fixed to avoid accidental movements or strong vibrations.
 The use of the SE-S floor stand or the SG-PSB Protective Armor Stands is

recommended. The mirror is fixed to these using the appropriate accessory mounting kit.
The use of the “SE-DM K DEVIATING MIRROR FIXING KIT” (cod.95ACC2530) is
recommended when installing the devices in environments characterized by strong
temperature variations and/or in presence of vibrations.

 Given the limited mirror width, the entire system is particularly sensitive also to small

rotations along the vertical axis of the mirror and emitting and receiving units.

 Hence particular attention has to be taken during system alignment and part fixing.
 To facilitate system installation (mirror/s and safety light curtain) the use of the Datalogic

SG-LP laser pointer is suggested.

The drawing shows an area protection system composed of a safety light curtain and two
mirrors.

Emitter

Receiver

Corner Mirror

Corner Mirror

Figure 1

2

SG-DM INSTRUCTION MANUAL

INSTALLATION

INSTALLATION ON SE-S/BOSCH BAR "STAND ALONE"

 Mounting requires the bracket kit ST-DM 95ASE1940.

1. Define the area to protect and the precise positions where the deviating mirrors and the
emitting and receiving units of the light curtain will be installed.

2. Fix the floor stands, in the defined points, verifying that their axes are perpendicular to
the floor.

3. Install the deviating mirrors and emitting and receiving units on the floor stands
respecting the warnings given previously. To mount the brackets on the mirror’s carter
insert the M6x50 UNI 5931 screw, coupling the bracket assembly to the carter’s slot and
tighten the screw (Figure 2).

4. Orient the mirrors to about 45° with respect to the optic path.

5. Insert the SG-LP laser pointer in the upper part of the emitting unit; orient the unit in order
that the laser beam hits the surface of the first mirror in a central point of the vertical axis
and at the same height at which the pointer is installed.

6. Repeat the same procedure inserting the pointer in the lower part of the unit; if necessary
repeat these procedures until the desired result is achieved.

7. Orient the first mirror in order that the laser beam hits the second mirror as described
above.

8. For the angular adjustment rotate the fixing brackets on the relative pins and fix the
screws when the required position is reached. For adjustments of the vertical axis use the
holes present of the mirror’s body and/or modify the inclination of the floor stand using
washers.

9. Orient the second mirror according to the same modes used previously guaranteeing that
the laser beam hits the receiving unit.

10. Insert the SG-LP laser pointer in the upper part of the receiving unit and, orientating this
unit, in order that the laser beam, reflected from the two mirrors, hits the emitting unit.

11. Repeat the same procedure inserting the laser pointer in the lower part of the unit.

M6x50 UNI 5931 screw

ST-DM mounting kit

Figure 2

3

SG-DM INSTRUCTION MANUAL

INSTALLATION ON SG-PSB

The various SG-DM models can be installed into the Protective Armor Stands
The SG-PSB Protective Armor Stand is an accessory to which both safety light curtains and

SG-DM Deviating Mirrors can be mounted.

In the case of the SG-DM 150, a pre-assembled Protective Armor Stand

NOTA

SG-PSM is available. See the SG-PSM manual for installation and
adjustment procedures.

CORRESPONDING MODELS

SG-DM CORRESPONDING SAFETY LIGHT CURTAIN

SGx-xx-015

SG-DM 600

SG-DM 900

2x SG-DM 150 / SG-DM 900

SG-DM 1200

3x SG-DM 150 / SG-DM 1200

4x SG-DM 150 / SG-DM 1200

SG-DM 1650

SGx-xx-030
SGx-xx-045
SGx-xx-060
SGx-xx-075
SG4-40-060
SG2-S2-050
SG4-S2-050
SG2-B2-050
SG4-B2-050
SG4-BLR2-050
SG4-BSR2-050
SGx-xx-090
SGx-xx-105
SG4-40-090
SG2-S3-080
SG4-S3-080
SG2-B3-080
SG4-B3-080
SG4-BLR3-080
SG4-BSR3-080
SG2-S4-090
SG4-S4-090
SG2-B4-090
SG4-B4-090
SG4-BLR4-090
SG4-BSR4-090
SGx-xx-120
SGx-xx-135
SGx-xx-150
SG4-40-120

4

SG-DM INSTRUCTION MANUAL

SG-DM CORRESPONDING SAFETY LIGHT CURTAIN

SG2-S4-120
SG4-S4-120

4x SG-DM 150 / SG-DM 1650

SG2-B4-120
SG4-B4-120
SG4-BLR4-120
SG4-BSR4-120

SG-DM 1900

SGx-xx-165
SGx-xx-180

OVERALL DIMENSIONS

Model 150, including ST-DM stand alone bracket mounting kit

Figure 3

5

SG-DM INSTRUCTION MANUAL

Models 600 to 1900, including ST-DM stand alone bracket mounting kit

Figure 4

The overall dimensions of the SG-DM mounted in the Protective Armor
Stand are available in the SG-PSB Instruction manual.

NOTA

DECLARATION OF CONFORMITY

We DATALOGIC AUTOMATION declare under our sole responsibility that these products are conform to the
2004/108/CE and successive amendments

WARRANTY

DATALOGIC AUTOMATION warrants its products to be free from defects.
DATALOGIC AUTOMATION will repair or replace, free of charge, any p roduct found to be defective during the
warranty period of 36 months from the manufacturing date.
This warranty does not cover damage or liability deriving from the improper application of DATALOGIC
AUTOMATION products.

DATALOGIC AUTOMATION Via Lavino 265
40050 Monte S.Pietro - Bologna – Italy
Tel: [phone] Fax: [phone]
www.automation.datalogic.com e-mail: [e-mail]

DATALOGIC AUTOMATION cares for the environment: 100% recycled paper.
DATALOGIC AUTOMATION reserves the right to make modifications and improvements without prior notification.

Datalogic and the Datalogic logo are registered trademarks of Datalo gic S.p.A. in many countries, including the
U.S.A. and the E.U.

© Copyright Datalogic 2011

6