Datalogic QL300, QL500 User Manual

5

5

QL300 / QL500

Quick Link ID-NET™ Connectors

DESCRIPTION

The QL series ID-NET™ connectors provide a fast and efficient
way to cable an ID-NET™ network using standard cables. The
QL300/500s are typically Master ID-NET™ connectors designed
to be used with the QL100/150/200s ID-NET™ Slave connectors.

The QL300 is a passive connection module which can be used in
Standalone or ID-NET™ Master Multidata, Slave Multidata or
Master Synchronized layouts. It provides separate ports for
Power Supply, External Trigger, Digital I/O and Communication.
Host communication is provided through connectivity to the
reader Main serial interface (RS232/485) or Aux RS232 serial
interface.
ID-NET™ network and power supply signals are sent out to the
next connected device by means of a dedicated port, however
input power is not received from the network. Therefore each
QL300 must be powered separately.

The QL500 is an active connection module which can be used in
Standalone or ID-NET™ Master Multidata, or Master
Synchronized layouts. It provides separate ports for Power
Supply, External Trigger, Digital I/O and Communication. Host
communication is provided through the integrated Ethernet
module which connects internally to the reader's Main serial
interface. Reader Aux RS232 serial interface is also provided.
ID-NET™ network and power supply signals are sent out to the
next connected device by means of a dedicated port, however
there is no network input connector and therefore it cannot be
used as an ID-NET™ Slave.

The QL series are compatible with the following readers:

DS2100N DS4800 Matrix 400™

DS2400N Matrix 200™

QL300

QL500

CONNECTIONS

ID-NET Out

M12 5P Female (A-coded)

Pin Function

1 Shield
2 Vdc
3 GND
4 ID+
5 ID-

QL300 only (ID-NET In)

M12 5P Male (A-coded)

Pin Function

1 Shield
2 nc
3 GND
4 ID+
5 ID-

QL500 only (Ethernet)

RJ45 8P Female

Pin Function

1 TX+
2 TX­3 RX+
6 RX-

4, 5, 7, 8 nc

OVERALL DIMENSIONS

129

[4.56]

42

[1.49]

42

[1.49]

45

[1.59]

129

[4.56]

45

[1.59]

QL300

QL500

56

56

[1.98]

[1.98]

76

76

[2.67]

[2.67]

P8 P1

mm

in

mm

in

27

27

[0.95]

[0.95]

Power

M12 3P Male (B-coded)

Pin Function

1 Earth
2 Vdc
3 GND

Trigger

M12 4P Female (A-coded)

Pin Function

1 +V
2 nc
3 -V
4 I1+

MOUNTING

There are two self-threading screws provided for mounting the
QLs to various wooden or plastic surfaces. Mounting to other
surfaces such as concrete walls or metallic panels requires user­supplied parts (screws, screw anchors, nuts, etc). Keep in mind
that the connected reader must have its Chassis grounded to
Earth, see paragraph "Grounding".

QLs can also be mounted to a Bosch Frame using the BA200
mounting accessory.

The distance between mounting bushings is given in the overall
dimension diagram for each QL.

IP65 protection is provided when the cables (or
QLs) are properly mated.

NOTE

GROUNDING

There are two general rules to follow regarding network
grounding:

1) The network Shield must only be connected to Earth
ground at one point (the Master).

When using isolated power supplies, Earth grounding can be
accomplished through the CAB-PW-EXT accessory cable and
the BA400 or QL300/500 Power connector.

QL300

CAB-PW-EXT

Power Supply

Earth ground connection

2) All reader Chassis must be connected to Earth ground.

All the readers in the network must have their Chassis
connected to Earth ground either by: mounting to

conductive metal brackets or frames which are connected to
Earth ground; or through the CBX or SC4000; or through the
QL bushing.

In the case of grounding through the CBX or SC4000, connect
the Earth signal to a good earth ground and set the internal
Chassis jumper to Earth.

In the case of grounding through the QL bushing, connect a
flying lead from the mounting bushing to an Earth ground. The
mounting bushing is internally connected to the reader
Chassis.

Power

Reader

13

1

25P D-Sub Female

142

Pin Function Pin Function

1,

shell,

both bushings

2 TXM 14 nc
3 RXM 15 nc
4
5
6 I2A 18 I1A
7 GND 19 GND
8 O1+ 20 RXA

9 nc 21 TXA
10 I2B 22 O1­11 O2+ 23 ID+
12 O2- 24 ID­13 Vdc 25 GND

Reader Chassis

RTSM *
CTSM *

16 nc
17 nc

* pins 4 and 5 are nc for QL500.

I/O Port

15P HD D-Sub Female

10

15

1

6

11

Pin Function Pin Function

1 O1+ 9 I2A
2 TXA 10 O2­3 RXA 11 I2B
4
5
6 O1- 14 SGND
7 Vdc 15
8 O2+

RXM *
CTSM *

12
13 GND

TXM *

RTSM *

* pins 4, 5, 12 and 15 are nc for QL500.

Do not connect GND and SGND to different (external)
ground references. GND and SGND are internally
connected through filtering circuitry which can be
permanently damaged if subjected to voltage drops over

CAUTION

0.8 Vdc.

ACCESSORIES

Description Part Number Connection
Cables

CAB-PW-EXT M12 POWER
EXTENSION CABLE

CBL-1480-01 THIN M12/5P
MALE/FEMALE 1M

CBL-1480-02 THIN M12/5P
MALE/FEMALE 2M

Terminators

CBL-1490 TERM. RESIST.
THIN M12/5P/MALE

CBL-1496 TERM. RESIST.
THIN M12/5P/FEMALE

Field Mountable Connectors

FMC400 M12 3P F. CONN.
POWER

Mounting

BA200 Bosch Adaptors 93ACC1822

The FMC accessory connectors can be used to make custom
External Power and Service cables in case the standard cables
don't satisfy the application requirements.

93A051381 Power

970101021

970101022

ID-NET Out/In

970101069 ID-NET Out

970101082 ID-NET In

93ACC1884 Power

TECHNICAL SPECIFICATIONS

A

A

ELECTRICAL FEATURES QL300 QL500

Supply Voltage 10 to 30 Vdc

(see Voltage Drop below)
Consumption - 210 mA - 70 mA
Maximum Distributed Current

4 A

Allowed

see related reading device
manual for consumption

Inputs see relative reader Reference Manual
Outputs see relative reader Reference Manual

PHYSICAL FEATURES

Mechanical Dimensions 129 x 76 x 27 mm

(5.1 x 3 x 1.1 in.)

Weight 312 g.

(11 oz.)

309

(10.9 oz.)

ENVIRONMENTAL FEATURES

Operating Temperature
Storage Temperature

0° to 50 C (+32° to 122 °F)

-20° to 70 C (-4° to 158 °F)
Humidity max. 90% non condensing
Vibration Resistance 14 mm @ 2 to 10 Hz
EN 60068-2-6

2 hours on each axis

1.5 mm @ 13 to 55 Hz
2 g @ 70 to 200 Hz

Shock Resistance 30 g; 11 ms;
EN 60068-2-27 3 shocks on each axis
Protection Class
EN 60529

(when IP protection caps or

IP65

IP cables and reading

device are correctly

connected)

IP40

The features given are typical at a 25 C ambient temperature (if not otherwise
indicated).

VOLTAGE DROP AND MAX DISTRIBUTED CURRENT
CALCULATIONS

For correct network management, the maximum number of readers which can
propagate power through the QLs must be calculated so that max distributed
current is not exceeded and so voltage drop doesn't affect reader functioning.
This is done according to the following formula:

Voltage Drop = (Max Reader Current x Number of readers) x

(Resistance per Meter per wire* x Cable length in Meters)

* the resistance calculation must include both wires (Vdc and GND).

Example:

An ID-NET™ network is composed of 4 DS2100N readers. Three 2 meter
ThinNet cables are used to connect the readers, which have Cable Resistance
= 0.058 Ohms per meter per wire. The network power is 24 Vdc.

(0.2083 A x 4 readers) x [(0.058 x 2) x 6 meters] = 0.58 Vdc voltage drop

24 Vdc - 0.58 = 23.42 Vdc at reader number 4 (worst case)

Integrate a sufficient number of QL200s to resupply network power.

821001640

TYPICAL LAYOUTS

Host

Point to Point - Matrix 200™ with QL500 (Ethernet to Host)

1

The reader must first be configured for Ethernet communication. This is done by connecting to the

reader through the RS232 Aux port available on the QL500 I/O Port and running the software
configuration program.

QL300

Power

CAB-PW-EXT

CBL-1496

ID-NET

Terminator

Main Interface

ID-NET™ Synchronized Network - Matrix 400™ Master with QL300

Power

ID-NET™

CBL-1480-xx

Master

PS

+ Matrix 400™ Slaves with QL150

CAB-PW-EXT

1

QL500

Ethernet

QL150

I/O

Matrix 200™

PS

CAB-AUX03 CAB-AUX03

QL150

Slave Nodes

The ID-NET network must be terminated inserting an
ID-NET terminator into the QL300 (Master) and into the
last QL in the network.

Host

CBL-1480-xx

CBL-1490

ID-NET

Terminator

TRIGGER

In order to allow direct trigger cabling between the photocell and the QL300/500 using standard
M12 A-coded one-to-one cables, the trigger signal has been internally wired to manage PNP
type photocells. The external trigger therefore must be connected as shown in the diagram

below.

Power 1

READER

VCC

~

+-

~

The electrical features of both inputs and outputs are given in the relative reader Reference
Manual.

13 Vdc

7

GND

I1B

19

18 I1

13

7

19

Reader

Vdc

23

QL300/500

GND

1 +V

3

-V

nc

2

4 I1+18

Trigger

EXTERNAL TRIGGER

V

Ground

Sig nal

Power

QL500 1

CAB-PW-EXT

Ethernet Interface

CBL-1480-xx

Power

Master

PS

QL200 2

Host

Slave Nodes

CBL-1480-xx

The ID-NET network must be terminated
inserting an ID-NET terminator into the last
QL in the network.
ID-NET on the QL500 is internally
terminated.

QL100 ID-NET™

ID-NET™ Synchronized Network - DS4800 Master with QL500

+ DS4800 Slaves with QL200 and QL100

1

The reader must first be configured for Ethernet communication. This is done by connecting to the

reader through the RS232 Aux port available on the QL500 I/O Port and running the software
configuration program.

2

The above diagram is an example showing layout connections and is not intended to represent power

limits, which instead, depend on each specific application. See "Voltage Drop and Max Distributed
Current Calculations".

Slave

CBL-1496

Terminator

PS

Power

QL300

Slave

ID-NET

PS PS

CBL-1480-xx

ID-NET™

The ID-NET network must be terminated inserting an
ID-NET terminator into the QL300 (Master) and into the
last QL300 in the network.

UX Port

QL300

Power

Master

CBL-1480-xx

QL300

ID-NET™ Multidata Network - DS4800 Master with QL300

+ Mixed Reader Slaves with QL300s

COMPLIANCE

FCC Compliance

Modifications or changes to this equipment without the expressed written approval of Datalogic could void the authority to
use the equipment.

This device complies with PART 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device
may not cause harmful interference, and (2) this device must accept any interference received, including interference
which may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the
FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is
operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be
required to correct the interference at his own expense.

CE Compliance
Warning:

This is a Class A product. In a domestic environment this product may cause radio interference in which case the user may
be required to take adequate measures.

Power Supply
This product is intended to be installed by Qualified Personnel only.

This accessory device is intended to be supplied by a UL Listed or CSA Certified Power Unit with «Class 2» or LPS power
source.

CBL-1490

ID-NET

Terminator

Power

CBL-1490

ID-NET

Terminator

Host