Datalogic Falcon 4423, PS6D4400UUSE Quick Start Manual

FCC Regulatory Compliancy

FCC Statement

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of
the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment
is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required
to correct the interference at his own expense.

CE Statement:

Warning
This is a Class A product. In a domestic environment this product may cause radio interference in which case the user may be
required to take adequate measures.

Parts List

1- PS6D4400UUSE USB, Ethernet, & Serial Charging Cradle
1 - USB Type-A to Type-B Cable (1 meter)
1 - Quick Connect Guide (this document)
1 - CAT5 Ethernet Cable

RJ45

USB

Spare

Battery

Serial

(RS232)

Power

Switch

Network USB

PS6SMC3000UE

Front

Type-B

Connector

Type-A

Connector

USB Type-A

to

Type-B Cable

Quick Start Guide

Ethernet,

USB, &

Serial

Charging

Cradles

PS6D4400UUSE

Spare

Battery

Plug the barrel connector
into the Cradle’s Power
Connector

Plug the
Standard
115V
Power Cord
into the Power
Adapter

Power Adapter

Charge your

Spare Battery

Connect Power

Local
Host

Computer

NETWORK USB

Connect 4400

Place the 4400 into the cradle to
charge the Datalogic Falcon.

Connect USB

For Local Communication:

Connect the USB Type-A connector to a Type-A
connector on the Host Computer.

Connect the USB Type-B connector to the USB
connector on the cradle.

Install Ethernet Driver

The Ethernet Cradle Driver is required for network communications with a CAT5 Ethernet cable.

For information on installing and configuring the Ethernet Cradle Driver, refer to steps and

on the reverse side.

Connect Network

For Network Communication:

Connect one end of the standard Ethernet
cable to the cradle’s RJ45 connector and
the other end to your hub, router, switch,
or wall data outlet

Choose

Slide Selector
Switch to choose
Network or USB
communication.

Part Number: 170384-000 Rev A

Problems?

Download the User’s Guide and
Troubleshooting Tips from the
Datalogic website at:
www.mobile.datalogic.com. Click
on the SW & Utilities link.

Still having problems?

Contact Technical Support at:
www.mobile.datalogic.com. Click on
the Contact Us link.

No other software is required if the default DHCP is used to obtain the cradle’s IP address. If a static
IP address or other special network requirement must be configured, you will also need to download
the Cradle Manager software from www.mobile.datalogic.com. Additional information on both programs
is contained in the User Manual, which is also available from the website.

Contact Support

Phone: [phone]
E-mail: [e-mail]
Hours: Monday - Friday 6:30 AM - 4:00 PM PST

For additional product inquiries or sales questions, please e-mail
[e-mail] or call 541.868.3610.

Troubleshooting Tips

Ensure you have set up an ActiveSync partnership with Host PC BEFORE you try to
setup PS6D4400UUSE.

Confirm connectivity by using Internet Explorer browser on Datalogic Falcon
Handheld Computer to visit a website on the internet, or try to ping the router
or a network computer.

Ensure PS6D4400UUSE is configured for network visibility - i.e.
(1) default setup is DHCP, or
(2) use Cradle Manager to configure for networks requiring a valid static IP address.
See the User Guide for more information on configuration issues.

Ensure the PS6D4400UUSE’s power adapter is connected, and functioning
correctly.

Ensure software is installed correctly.

More Troubleshooting help is available in the User Guide.

Windows CE

1. Launch app (Start -> Programs ->
Communication ->
Ethernet Cradle Driver)

2. Enable connection by clicking the
Enable Cradle Driver checkbox.
(See image )

Install Ethernet Cradle Driver

Configure Ethernet Cradle Driver

Download the Ethernet Cradle Driver software from the Datalogic website at
www.mobile.datalogic.com. Click on the SW & Utilities link to find the appropriate file.

Use ActiveSync to copy the CradleDrvr CAB file into the Windows directory on the terminal.

Use the terminal’s File Explorer application to locate the CradleDrvr CAB file and tap on it with
the Stylus to install it.

Warm boot the terminal. Follow the instructions in the terminal’s User Guide if you need
guidance.

Windows Mobile 5.0

1. Launch app (Start -> Programs ->
Communication ->
Ethernet Cradle Driver)

2. Enable connection by clicking the
Enable Cradle Driver checkbox.
(See image )

3. Disable RNDIS (Start->Settings->
Connections->USB to PC-> and
deselect “Enable advanced network
functionality”)
(See image )

4. Configure network settings (Start->
Settings->Connections->
Connections->Advanced->
Select Network Settings->.
Set both dropdowns to “My Work
Network”)
(See image )

No other software is required if the default DHCP is used to obtain the cradle’s IP address.
If a static IP address or other special network requirement must be configured, you will also
need to download the Cradle Manager software from www.mobile.datalogic.com. Additional
information on both programs is contained in the User Manual, which is also available from
the website.