Datalogic Gryphon GD44XX, Gryphon I GD44 Series, Gryphon GD4400 Quick Reference Manual

Page 1
Gryphon™ I GD44XX
General Purpose Corded Handheld
Area Imager Bar Code Reader
Quick Reference Guide
Page 2
Datalogic Scanning, Inc.
959 Terry Street Eugene, Oregon 97402 USA Telephone: (541) 683-5700 Fax: (541) 345-7140
An Unpublished Work - All rights reserved. No part of the con­tents of this documentation or the procedures described therein may be reproduced or transmitted in any form or by any means without prior written permission of Datalogic Scanning, Inc. or its subsidiaries or affiliates ("Datalogic" or “Datalogic Scanning”). Owners of Datalogic products are hereby granted a non-exclu­sive, revocable license to reproduce and transmit this documen­tation for the purchaser's own internal business purposes. Purchaser shall not remove or alter any proprietary notices, including copyright notices, contained in this documentation and shall ensure that all notices appear on any reproductions of the documentation.
Should future revisions of this manual be published, you can acquire printed versions by contacting your Datalogic represen­tative. Electronic versions may either be downloadable from the Datalogic website (www.scanning.datalogic.com) or provided on appropriate media. If you visit our website and would like to make comments or suggestions about this or other Datalogic publications, please let us know via the "Contact Datalogic" page.
Disclaimer
Datalogic has taken reasonable measures to provide informa­tion in this manual that is complete and accurate, however, Dat­alogic reserves the right to change any specification at any time without prior notice.
Datalogic and the Datalogic logo are registered trademarks of Datalogic S.p.A. in many countries, including the U.S.A. and the E.U. All other brand and product names may be trademarks of their respective owners.
Patents
This product is covered by one or more of the following patents. Design Patents: CN ZL200830142386.5; CN ZL200930006852.1;
CN ZL201030175545.9 ; EP870787; EP1177943; USD599799; USD606076
Utility Patents: EP996284; EP999514; EP1128315; EP1172756; EP1396811; EP1413971; JP4435343; US5311000; US5330370; US5481098; US6478224; US6512218; US6513714; US6561427; US6758403; US6808114; US6877664; US6997385; US7053954; US7234641; US7387246
Additional patents pending.
Page 3
Table of Contents
Software Product Policy .............................................................................4
Customers Under Software Support ..........................................4
Description .....................................................................................................5
Setting Up the Reader ................................................................................6
Connect/Disconnect Cable to Reader ........................................6
Using the Gryphon™ I GD44XX ................................................................7
Selecting the Interface Type .....................................................................8
Interface Selection ............................................................................8
Configuring the Interface .................................................... 8
Keyboard Interface.............................................................. 11
Scancode Tables .................................................................. 13
Country Mode....................................................................... 13
Caps Lock State .................................................................... 18
Numlock.................................................................................. 19
Programming ..............................................................................................20
Using Programming Bar Codes .................................................20
Configure Other Settings .............................................................20
Resetting Product Defaults .........................................................20
Reading Parameters .................................................................................21
Aiming System ................................................................................21
Good Read Green Spot Duration ..............................................21
Operating Modes ......................................................................................22
Scan Mode ........................................................................................22
Pick Mode ..........................................................................................24
Multiple Label Reading ................................................................24
Technical Specifications ..........................................................................25
LED and Beeper Indications ...................................................................28
Error Codes ..................................................................................................31
Cleaning ........................................................................................................32
Regulatory Information ...........................................................................33
Statement of Agency Compliance ...........................................33
FCC Class B Compliance Statement .........................................33
FCC RF Radiation Exposure Statement........................ 34
Canadian Notice ..............................................................................34
Power Supply ...................................................................................34
Imager Labeling ..............................................................................35
Aiming System...................................................................... 35
WEEE Statement .............................................................................40
Warranty .......................................................................................................41
Ergonomic Recommendations .............................................................42
Services and Support ...............................................................................42
Page 4
NOTES
Page 5
Quick Reference Guide 1
Datalogic Scanning, Inc.
GRYPHON™ PRODUCT SERIES
END USER LICENSE AGREEMENT
Notice to End User: The Datalogic Product you have acquired contains embedded Software, which is integral to the product's operation. This Software is being provided to you under license, subject to the terms and conditions of this Agreement. If you use the Datalogic Product, you will be deemed to have accepted the terms and conditions of this Agreement. If you do not intend to be bound to the terms of this Agreement, Datalogic is not willing to license the Software to you, you may not use the Datalogic Product or the Software, and you must contact the party from whom you acquired the Datalogic Product for instructions.
This End User Software License Agreement ("Agreement") is a legally binding agree­ment governing the licensing of the Software and Documentation by Datalogic Scan­ning, Inc. and its Affiliates ("Datalogic") to the entity or person who has purchased or otherwise acquired a Datalogic Product ("End User"). For purposes of this Agreement, any software that is associated with a separate end-user license agreement is licensed to you under the terms of that license agreement. Datalogic and End User hereby agree as follows:
1. Definitions
1.1 "Affiliate" means a business entity currently existing or later acquired that controls, is controlled by, or is under common control with Datalogic S.p.A.
1.2 "Documentation" means materials such as user's guides, program reference guides, quick reference guides, manuals, or similar materials associated with or related to the Datalogic Product, whether in printed, "online", or other form.
1.3 "Proprietary Information" means: (a) source code, object code, software, docu­mentation, and any related internal design, system design, data base design, algorithms, technology, technical data or information, implementation tech­niques, and trade secrets related to the Software, (b) any other trade secrets marked appropriately or identified as proprietary or confidential, and (c) any information that End User, under the circumstances, should recognize as confi­dential. Proprietary Information does not include any information that the receiv­ing party can establish was (1) in the public domain, (2) already in the receiving party's possession or rightfully known prior to receipt, (3) rightfully learned from a third party not in violation of any other's proprietary rights, or (4) indepen­dently developed without access to Proprietary Information.
1.4 "Datalogic Product" means the Datalogic® Gryphon™ series scanner product, including all embedded Software in and all Documentation related to such prod­uct, which has been purchased or otherwise acquired by End User, whether obtained directly or indirectly from Datalogic.
1.5 "Software" means any software or computer programs of Datalogic or its third party licensors in machine readable form which is embedded in the Datalogic Product, whether obtained directly or indirectly from Datalogic, including any replacement, update, upgrade, enhancement or modification.
2. Scope Of License Granted
2.1 Datalogic grants to End User a non-exclusive, non-transferable, perpetual license to use the Software, solely on the Datalogic Product in which it is embedded ("designated Datalogic Product"), in machine-readable form only, solely for End User's internal business purposes. This Agreement does not convey ownership of the Software to End User. Title to the Software shall be and remain with Datalogic or the third party from whom Datalogic has obtained a licensed right. As used in this Agreement, the term "purchase" or its equivalents when applied to the Soft­ware shall mean "acquire under license." End User is not entitled to receipt or use of the source code to any Software.
2.2 End User shall not copy, modify, decompile, disassemble, reverse engineer, or otherwise reproduce or remanufacture the Software, whether modified or unmodified, nor sell, assign, sublicense, distribute, lend, rent, give, or otherwise transfer the Software to any other person or organization, for purposes other than as expressly provided in this Agreement, without Datalogic's prior written consent.
3. Transfers, Support
3.1 Any copying, installing, reproduction, remanufacture, reverse engineering, elec­tronic transfer, or other use of the Software on other than the designated Data­logic Product will be a material breach of this Agreement. However, Datalogic may elect not to terminate this Agreement or the granted licenses, but instead
Page 6
2 Gryphon™ I GD44XX
may elect to notify End User that End User is deemed to have ordered and accepted a license for each breaching use. End User shall pay Datalogic the appli­cable list price for such licenses as of the date of such breach.
3.2 End User shall not sell, assign, sublicense, distribute, lend, rent, give, or otherwise transfer the Datalogic Product to any third party unless such third party agrees with Datalogic in writing to be bound by the terms and conditions of this Agree­ment. Any such transfer of the Datalogic Product absent such agreement shall be null and void.
3.3 End User may obtain support for Software from Datalogic at Datalogic's standard support fees and under Datalogic's standard support terms and conditions in effect at the time the support is requested.
4. Intellectual Property
End User acknowledges that the Software constitutes valuable trade secrets of Data­logic or Datalogic's third party licensors and that the Software is protected by intellec­tual property laws and treaties. The license set forth in this Agreement does not transfer to End User any ownership of Datalogic's or its third party licensors' copy­rights, patents, trademarks, service marks, trade secrets, or other intellectual property rights and End User shall have no right to commence any legal actions to obtain such rights. End User shall not remove, modify, or take any other action that would obscure any copyright, trademark, patent marking, or other intellectual property notices con­tained in or on the Datalogic Product.
5. Proprietary Information
5.1 End User acknowledges that Proprietary Information is the confidential, proprie­tary, and trade secret property of Datalogic and Datalogic's third party licensors and End User acquires no right or interest in any Proprietary Information.
5.2 End User shall not disclose, provide, or otherwise make available the Proprietary Information of Datalogic or its third party licensors to any person other than End User's authorized employees or agents who are under confidentiality agreement, and End User shall not use the Proprietary Information other than in conjunction with use of the Datalogic Product exclusively for End User's internal business pur­poses. End User shall take steps to protect the Proprietary Information no less securely than if it were End User's own intellectual property.
5.3 The provisions of this Proprietary Information Section shall survive and continue for five (5) years after the termination of this Agreement.
6. Limited Warranty
6.1 Datalogic warrants that, under normal use and operation, the Datalogic Product will conform substantially to the applicable Documentation for the period speci­fied in the Documentation. During this period, for all reproducible nonconformi­ties for which Datalogic has been given written notice, Datalogic will use commercially reasonable efforts to remedy nonconformities verified by Data­logic. End User agrees to supply Datalogic with all reasonably requested informa­tion and assistance necessary to help Datalogic in remedying such nonconformities. For all defects reported to Datalogic within the warranty period, Datalogic's liability is limited to providing End User with one copy of corrections or responding to End User's problem reports according to Datalogic's standard assistance practices. Datalogic does not warrant that the product will meet End User's requirements or that use of the product will be uninterrupted or error free, or that Datalogic's remedial efforts will correct any nonconformance. This limited warranty does not cover any product that have been subjected to damage or abuse, whether intentionally, accidentally, or by neglect, or to unauthorized repair or unauthorized installation, and shall be void if End User modifies the product, uses the product in any manner other than as established in the Docu­mentation, or if End User breaches any of the provisions of this Agreement.
6.2 EXCEPT AS PROVIDED IN THIS AGREEMENT, THE DATALOGIC PRODUCT IS PRO­VIDED "AS IS" AND DATALOGIC MAKES NO WARRANTIES OF ANY KIND, EXPRESS OR IMPLIED, WRITTEN OR ORAL, WITH RESPECT TO THE PRODUCT, AND SPECIFI­CALLY DISCLAIMS THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FIT­NESS FOR A PARTICULAR PURPOSE.
7. Infringement
7.1 Datalogic will defend End User against any claim in a lawsuit that the Datalogic Product furnished hereunder infringe a United States patent or copyright of a third party and Datalogic will pay any damages finally awarded against End User by a court of competent jurisdiction that are attributable to such claim or will pay End User's part of any settlement that is attributable to such claim, provided, that
Page 7
Quick Reference Guide 3
1) End User notifies Datalogic promptly in writing of the claim, 2) Datalogic con­trols the defense or settlement of the claim, and 3) End User cooperates fully with Datalogic in such defense or settlement. All notices of a claim should be sent to Datalogic Scanning, Inc., Legal Department, 959 Terry Street, Eugene, OR 97402.
7.2 In the defense or settlement of any such claim, Datalogic may, at its option, 1) procure for End User the right to continue using the Datalogic Product, 2) modify the Datalogic Product so that it becomes non-infringing, 3) replace the Datalogic Product with an equivalent product not subject to such claim, or 4) provide End User an opportunity to return the Datalogic Product and receive a refund of the purchase price paid, less a reasonable allowance for use.
7.3 Datalogic shall have no liability to End User for claims of infringement based upon 1) the use of any Datalogic Product in combination with any product which Datalogic has not either furnished or authorized for use with such Datalogic Product 2) the use of any Datalogic Product designed, manufactured, or modified to the specifications of End User, or 3) End User's modification of the Datalogic Product without written authorization from Datalogic.
7.4 THE FOREGOING STATES DATALOGIC'S COMPLETE AND ENTIRE OBLIGATION CON­CERNING CLAIMS OF PATENT, COPYRIGHT, OR OTHER INTELLECTUAL PROPERTY INFRINGEMENT, CANCELS AND SUPERCEDES ANY PRIOR AGREEMENTS, WHETHER ORAL OR WRITTEN, BETWEEN THE PARTIES CONCERNING SUCH CLAIMS, AND WILL NOT BE MODIFIED OR AMENDED BY ANY PAST, CONTEMPO­RANEOUS, OR FUTURE AGREEMENTS OR DEALINGS BETWEEN THE PARTIES, WHETHER ORAL OR WRITTEN, EXCEPT AS SET FORTH IN A FUTURE WRITING SIGNED BY BOTH PARTIES.
8. Limitation Of Liability
EXCEPT AS PROVIDED IN SECTION 7, DATALOGIC SHALL NOT BE LIABLE FOR ANY CLAIMS AGAINST END USER BY ANY OTHER PARTY. IN NO EVENT SHALL DATALOGIC'S LIABILITY FOR DAMAGES, IF ANY, WHETHER BASED UPON CONTRACT, TORT (INCLUDING NEGLI­GENCE), PRODUCT LIABILITY, STRICT LIABILITY, WARRANTY, OR ANY OTHER BASIS, EXCEED THE PRICE OR FEE PAID BY END USER FOR THE DATALOGIC PRODUCT. UNDER NO CIRCUMSTANCES SHALL DATALOGIC BE LIABLE TO END USER OR ANY THIRD PARTY FOR LOST PROFITS, LOST DATA, INTERRUPTION OF BUSINESS OR SERVICE, OR FOR ANY OTHER SPECIAL, CONSEQUENTIAL, CONTINGENT, INDIRECT, INCIDENTAL, PUNITIVE, EXEMPLARY, OR OTHER SIMILAR DAMAGES, EVEN IF DATALOGIC HAS BEEN ADVISED OF THE POSSIBIL­ITY OF SUCH DAMAGES.
9. Government Restricted Rights; International Use
9.1 Use, duplication, or disclosure of the Software by the U.S. Government is subject to the restrictions for computer software developed at private expense as set forth in the U.S. Federal Acquisition Regulations at FAR 52.227-14(g), or 52.227-19 or in the Rights in Technical Data and Computer Software clause at DFARS
252.227-7013(c)(1)(ii), whichever is applicable.
9.2 If End User is using the Datalogic Product outside of the United States, End User must comply with the applicable local laws of the country in which the Datalogic Product is used, with U.S. export control laws, and with the English language ver­sion of this Agreement. The provisions of the "United Nations Convention on International Sale of Goods" shall not apply to this Agreement.
10. Termination
10.1 Either party may terminate this Agreement or any license granted under this Agreement at any time upon written notice if the other party breaches any provi­sion of this Agreement.
10.2 Upon termination of this Agreement, End User immediately shall cease using any nonembedded software and shall return to Datalogic or destroy all non-embed­ded software covered by this Agreement, and shall furnish Datalogic with a certif­icate of compliance with this provision signed by an officer or authorized representative of End User. For embedded software, End User agrees to sign a waiver prepared by Datalogic concerning further use of the embedded Software. End User's resumed or continued use of the embedded Software after termina­tion shall constitute End User's agreement to be bound by the terms and condi­tions of this Agreement for such use.
11. General Provisions
11.1 Entire Agreement; Amendment. This document contains the entire agreement between the parties relating to the licensing of the Software and supersedes all prior or contemporaneous agreements, written or oral, between the parties con­cerning the licensing of the Software. This Agreement may not be changed, amended, or modified except by written document signed by Datalogic.
Page 8
Software Product Policy
4 Gryphon™ I GD44XX
11.2 Notice. All notices required or authorized under this Agreement shall be given in writing, and shall be effective when received, with evidence of receipt. Notices to Datalogic shall be sent to the attention of Contract Administration, Datalogic Scanning, Inc., 959 Terry Street, Eugene, OR 97402, or such other address as may be specified by Datalogic in writing.
11.3 Waiver. A party's failure to enforce any of the terms and conditions of this Agree­ment shall not prevent the party's later enforcement of such terms and condi­tions.
11.4 Governing Law; Venue: This Agreement and the rights of the parties hereunder shall be governed by and construed in accordance with the laws of the State of Oregon U.S.A, without regard to the rules governing conflicts of law. The state or federal courts of the State of Oregon located in either Multnomah or Lane coun­ties shall have exclusive jurisdiction over all matters regarding this Agreement, except that Datalogic shall have the right, at its absolute discretion, to initiate proceedings in the courts of any other state, country, or territory in which End User resides, or in which any of End User's assets are located.
11.5 Attorneys' Fees. In the event an action is brought to enforce the terms and condi­tions of this Agreement, the prevailing party shall be entitled to reasonable attor­neys' fees, both at trial and on appeal.
- END -
Software Product Policy
Datalogic reserves the right to ship its products with the latest version of software/firmware available. This provides our cus­tomers with the very latest in Datalogic software technology.
The only exception to this policy is when the buyer has a signed contract with Datalogic that clearly defines the terms and conditions for making software/firmware changes in products shipped to the buyer.
Customers Under Software Support
Customers that elect to subscribe to Datalogic Software Main­tenance and Support Agreement will receive 30 days advance notification of: (1) the release of a new software version; and/ or (2) discontinuation of any prior software version that will no longer be supported. Datalogic will provide maintenance for a fee that will assist customers in transitioning to the next software version. If a customer is currently using the software version being discontinued, the customer may elect to transi­tion to any one of the newer versions, depending on the hard­ware in use.
To arrange for a Software Maintenance and Support Agree­ment please contact your Datalogic sales person.
Page 9
Quick Reference Guide 5
Gryphon™ I GD44XX
Description
With rich feature sets and extensive model options, the Gry­phon
product series from Datalogic Scanning represents the premium level of data collection equipment for general pur­pose applications. The Gryphon I GD44XX reader has en­hanced optics with improved motion tolerance, allowing codes placed on fast-moving objects to be easily and quickly captured, creating the ideal reader for tasks requiring high throughput like those found in retail and light industrial envi­ronments.
Omni­Directional Operating
To read a symbol or capture an image, simply aim the reader and pull the trigger. The Gryphon™ I GD44XX is a powerful omni-directional reader, so the orientation of the symbol is not important. Datalogic’s exclusive patented ‘Green Spot’ for good-read feedback helps to improve productiv­ity in noisy environments or in situations where silence is required. When using the product with the cradle at a 45° position, the aiming pattern can work as an aiming system to aid in position­ing the bar code for quick and intuitive reading.
Decoding
Reliably decodes all standard 1D (linear) and 2D bar codes, including GS1 DataBar™ linear codes, Postal Codes (China Post), Stacked Codes (such as GS1 DataBar Expanded Stacked, GS1 DataBar Stacked, GS1 DataBar, Stacked Omnidirectional). The data stream — acquired from decoding a symbol — is rapidly sent to the host. The reader is immediately available to read another symbol.
Imaging
The Gryphon™ I GD44XX can also function as a camera by capturing entire images or image por­tions of labels, signatures, and other items. See the Datalogic Aladdin configuration tool for infor­mation and options for this feature.
Page 10
Setting Up the Reader
6 Gryphon™ I GD44XX
Setting Up the Reader
Follow the steps below to connect and get your reader up and communicating with its host.
1. Connect the Cable to the reader and the Host.
2. Configure the Interface (see page 8).
3. Configure the Reader starting on page 20 (optional, depends on settings needed)
Connect/Disconnect Cable to Reader
Figure 1. Connecting to the Reader
Host Connection:
The Gryphon plugs directly into the host de-
vice as shown in
Figure 2. The power can also be supplied
through an external power supply via the Interface Cable sup­plied with a power jack.
Figure 2. Connecting to the Host
U
S
B
Page 11
Using the Gryphon™ I GD44XX
Quick Reference Guide 7
Using the Gryphon™ I GD44XX
The Gryphon™ I GD44XX normally functions by capturing and decoding codes. The reader is equipped with an internal motion-sensing function which activates the aiming system on device motion. The intelligent aiming system indicates the field of view which should be positioned over the bar code:
Aiming System
Relative Size and Location of Aiming System Pattern
A red beam illuminates the label. The field of view indicated by the aiming system will be smaller when the reader is closer to the bar code and larger when it is farther from the code. Symbologies with smaller bars or elements (mil size) should be read closer to the unit. Symbologies with larger bars or ele­ments (mil size) should be read farther from the unit.
If the aiming system is centered and the entire bar code is within the aiming field, you will get a good read. Successful reading is signaled by an audible tone plus a good-read green spot LED indicator.
Reference the Gryphon I GD44XX Product Reference Guide (PRG) for more information about this feature and other pro­grammable settings.
Linear bar code
2D Matrix symbol
Page 12
Selecting the Interface Type
8 Gryphon™ I GD44XX
Selecting the Interface Type
Upon completing the physical connection between the reader and its host, proceed directly to Interface Selection below for information and programming for the interface type the read­er is connected to (for example: RS-232, Keyboard Wedge, USB, etc.) and scan the appropriate bar code to select your sys­tem’s correct interface type.
Interface Selection
Each reader model will support one of the following sets of host interfaces:
General Purpose Models:
RS-232, RS-232 OPOS, USB, Key-
board Wedge, Wand.
Retail Point of Sale Models :
RS-232, RS-232 OPOS, USB,
IBM 46XX. Information and programming options for each interface type
are provided in this section. For defaults and additional infor­mation associated with each interface, proceed to the corre­sponding chapter in the Gryphon™ 4400 PRG.
Configuring the Interface
Scan the appropriate programming bar code to selects the in­terface type for your system.
Unlike some other programming features and options, interface selections require that you scan only one programming bar code label. DO NOT scan an ENTER/EXIT bar code prior to scanning an inter­face selection bar code.
Some interfaces require the scanner to start in the disabled state when powered up. If additional scan­ner configuration is desired while in this state, pull the trigger and hold for 5 seconds. The scanner will change to a state that allows programming with bar codes.
Page 13
Selecting the Interface Type
Quick Reference Guide 9
RS-232
RS-232 standard interface
Select RS232-STD
RS-232 Wincor-Nixdorf
Select RS232-WN
RS-232 for use with OPOS/UPOS/JavaPOS
Select RS-232 OPOS
USB Com to simulate RS-232 standard interface
Select USB-COM-STD
a
Page 14
Selecting the Interface Type
10 Gryphon™ I GD44XX
IBM
IBM-46xx Port 5B reader interface
Select IBM-P5B
IBM-46xx Port 9B reader interface
Select IBM-P9B
USB-OEM
USB-OEM
(can be used for OPOS/UPOS/JavaPOS)
Select USB-OEM
a. Download the correct USB Com driver from www.datalogic.com
Page 15
Selecting the Interface Type
Quick Reference Guide 11
Keyboard Interface
Use the programming bar codes to select options for USB Keyboard and Wedge Interfaces.
KEYBOARD
AT, PS/2 25-286, 30-286, 50, 50Z, 60, 70, 80, 90 & 95 w/
Standard Key Encoding
Select KBD-AT
Keyboard Wedge for IBM AT PS2 with standard key encoding but
without external keyboard
Select KBD-AT-NK
AT, PS/2 25-286, 30-286, 50, 50Z, 60, 70, 80, 90 & 95
w/Alternate Key
Select KBD-AT-ALT
Keyboard Wedge for IBM AT PS2 with alternate key encoding but
without external keyboard
Select KBD-AT-ALT-NK
Page 16
Selecting the Interface Type
12 Gryphon™ I GD44XX
KEYBOARD (continued)
PC/XT w/Standard Key Encoding
Select KBD-XT
Keyboard Wedge for IBM Terminal 3153
Select KBD-IBM-3153
Keyboard Wedge for IBM Terminals 31xx, 32xx, 34xx, 37xx make
only keyboard
Select KBD-IBM-M
Keyboard Wedge for IBM Terminals 31xx, 32xx, 34xx, 37xx make
break keyboard
Select KBD-IBM-MB
USB Keyboard with alternate key encoding
Select USB Alternate Keyboard
USB Keyboard for Apple computers
Select USB-KBD-APPLE
Page 17
Selecting the Interface Type
Quick Reference Guide 13
Scancode Tables
Reference the Gryphon 4400 PRG for information about control character emulation for keyboard interfaces.
Country Mode
This feature specifies the country/language supported by the keyboard. Only these interfaces support ALL Country Modes:
USB Keyboard (without alternate key encoding)
AT, PS/2 25-286, 30-286, 50, 50Z, 60, 70, 80, 90 & 95 w/Std Key Encoding
Keyboard Wedge for IBM AT PS2 with standard key encoding but without external keyboard
AT, PS/2 25-286, 30-286, 50, 50Z, 60, 70, 80, 90 & 95 without Alternate Key
Keyboard Wedge for IBM AT PS2 without alternate key encoding but without external keyboard
All other interfaces support ONLY the following Country Modes: U.S., Belgium, Britain, France, Germany, Italy, Spain, Sweden.
KEYBOARD (continued)
Keyboard Wedge for DIGITAL Terminals
VT2xx, VT3xx, VT4xx
Select KBD-DIG-VT
USB Keyboard with standard key encoding
Select USB Keyboard
WAND EMULATION
Wand Emulation
Select WAND
Page 18
Selecting the Interface Type
14 Gryphon™ I GD44XX
COUNTRY MODE
ENTER/EXIT PROGRAMMING MODE
Country Mode = U.S.
Country Mode = Belgium
Country Mode = Britain
Country Mode = Croatia*
*
Supports only the interfaces listed in the Country Mode feature description
Page 19
Selecting the Interface Type
Quick Reference Guide 15
COUNTRY MODE (Continued)
Country Mode = Czech*
Country Mode = Denmark*
Country Mode = France
Country Mode = Germany
Country Mode = Hungary*
Country Mode = Italy
*
Supports only the interfaces listed in the Country Mode feature description
Page 20
Selecting the Interface Type
16 Gryphon™ I GD44XX
COUNTRY MODE (Continued)
Country Mode = Japanese 106-key*
Country Mode = Norway*
Country Mode = Poland*
Country Mode = Portugal*
Country Mode = Romania*
Country Mode = Spain
*
Supports only the interfaces listed in the Country Mode feature description
Page 21
Selecting the Interface Type
Quick Reference Guide 17
COUNTRY MODE (Continued)
Country Mode = Sweden
Country Mode = Slovakia*
Country Mode = Switzerland*
*Supports only the interfaces listed in the Country Mode feature description
Page 22
Selecting the Interface Type
18 Gryphon™ I GD44XX
Caps Lock State
This option specifies the format in which the reader sends character data. This applies to keyboard wedge interfaces. This does not apply when an alternate key encoding keyboard is se­lected.
ENTER/EXIT PROGRAMMING MODE
Caps Lock State = Caps Lock OFF
Caps Lock State = Caps Lock ON
Caps Lock State = AUTO Caps Lock Enable
Page 23
Selecting the Interface Type
Quick Reference Guide 19
Numlock
This option specifies the setting of the Numbers Lock (Num­lock) key while in keyboard wedge interface. This only applies to alternate key encoding interfaces. It does not apply to USB keyboard.
ENTER/EXIT PROGRAMMING MODE
Numlock = Numlock key unchanged
Numlock = Numlock key toggled
Page 24
Programming
20 Gryphon™ I GD44XX
Programming
The reader is factory-configured with a set of standard default features. After scanning the interface bar code from the Inter­faces section, select other options and customize your reader through use of the programming bar codes available in the Gryphon I GD44XX PRG. Check the corresponding features section for your interface, and also the Data Editing and Sym­bologies chapters of the PRG.
Using Programming Bar Codes
This manual contains bar codes which allow you to reconfig­ure your reader. Some programming bar code labels, like the "Reset Default Settings" on page 20, require only the scan of that single label to enact the change.
Other bar codes require the reader to be placed in Program­ming Mode prior to scanning them. Scan an ENTER/EXIT bar code once to enter Programming Mode; scan the desired parameter settings; scan the ENTER/EXIT bar code again to accept your changes, which exits Programming Mode and re­turns the reader to normal operation.
Configure Other Settings
Additional programming bar codes are available in the PRG to allow for customizing programming features. If your installa­tion requires different programming than the standard factory default settings, refer to the PRG.
Resetting Product Defaults
If you aren’t sure what programming options are in your read­er, or you’ve changed some options and want your custom fac­tory settings restored, scan the bar code below to reset the reader to its initial configuration. Reference the PRG for other options, and a listing of standard factory settings.
Factory defaults are based on the interface type. Be sure your reader is configured for the correct inter­face before scanning this label. See "Selecting the Interface Type" on page 8 for more information.
Reset Default Settings
Page 25
Reading Parameters
Quick Reference Guide 21
Reading Parameters
Move the reader toward the target and center the aiming pat­tern and illumination system to capture and decode the image. See Using the Gryphon™ I GD44XX on page 7 for more informa­tion.
The aiming system will briefly switch off after the acquisition time, and if no code is decoded will switch on again before the next acquisition. The illuminator will remain on until the symbol is decoded.
As you read code symbols, adjust the distance at which you are holding the reader.
Aiming System
A number of options for customizing control of the Aiming System are available. See the Gryphon I GD44XX PRG for more information and programming bar codes.
Good Read Green Spot Duration
Successful reading can be signaled by a good read green spot. Use the bar codes that follow to specify the duration of the good read pointer beam after a good read.
ENTER/EXIT PROGRAMMING MODE
Disabled
Short (300 ms)
Medium (500 ms)
Long (800 ms)
Page 26
Operating Modes
22 Gryphon™ I GD44XX
Operating Modes
Scan Mode
The imager can be set to operate in one of several scanning modes. See the PRG for more information and settings for any of the options:
Trigger Single (Default):
This mode is associated with typical handheld reader operation. Motion Sense is active and if the scanner detects motion the aiming pattern is turned on. When the trigger is pulled, illumination is turned on and the scanner attempts to read a label. Scanning is activated until one of the following occurs:
the programmable “maximum scan on time”
1
has
elapsed
a label has been read
the trigger is released
Trigger Pulse Multiple:
Scanning begins when the trigger is pulled and continues after the trigger is released, until the trig­ger is pulled again or until the programmable “maximum scan on time”
1
has elapsed. Reading a label does not disable scan­ning. Double Read Timeout1 prevents undesired multiple reads while in this mode.
Trigger Hold Multiple :
When the trigger is pulled, scanning starts and the product scans until the trigger is released or “maximum scan on time”
1
has elapsed. Reading a label does not disable scanning. Double Read Timeout1 prevents unde­sired multiple reads while in this mode.
Always On:
The illuminator is always ON and the reader is al­ways ready for code reading. Double Read Timeout1 prevents undesired multiple reads.
Flashing:
The reader illuminator flashes on and off regardless of the trigger status. Code reading takes place only during the Flash On
2
time. Double Read Timeout1 prevents undesired
multiple reads.
1. See the Product Reference Guide (PRG) for these and other programmable features
2. Controlled by Flash On Time and Flash Off Time. Use the PRG to program these options.
Page 27
Operating Modes
Quick Reference Guide 23
Stand Mode:
In Stand Mode, the illumination remains on for a configurable amount of time after a good read occurs. The scanner exits stand mode when movement is detected. If the trigger is activated from stand mode, the scanner transitions into one of the triggered modes.
ENTER/EXIT PROGRAMMING MODE

Scan Mode = Trigger Single
Scan Mode = Trigger Pulse Multiple
Scan Mode = Trigger Hold Multiple
Scan Mode = Flashing
Scan Mode = Always On
Scan Mode = Stand Mode
Page 28
Operating Modes
24 Gryphon™ I GD44XX
Pick Mode
Specifies the ability of the reader to decode labels only when they are close to the center of the aiming pattern. Pick Mode is a Decoding and Transmission process where bar codes that are not within the configurable distance from the center of the aiming pattern are not acknowledged or transmitted to the host. It is active only while the scanner is in Trigger Single mode. If the scanner switches to a different Read Mode, Pick Mode is automatically disabled.
Multiple Label Reading
The reader offers a number of options for multiple label read­ing. See the PRG or software configuration tool for descrip­tions of these features and programming labels.
This feature is not compatible with Multiple Labels Reading in a Volume. See the PRG for more infor­mation.
ENTER/EXIT PROGRAMMING MODE

PIck Mode = Disable
Pick Mode = Enable
Page 29
Technical Specifications
Quick Reference Guide 25
Technical Specifications
The following table contains Physical and Performance Char­acteristics, User Environment and Regulatory information.
Item Description
Physical Characteristics
Color Black
Dimensions
Height 7.1”/181 mm Length 3.9”/100 mm Width 2.8”/71 mm
Weight (without cable) Approximately 6.9 ounces /195.6 g
Electrical Characteristics
Voltage & Current
Input Voltage
• GD441X: 4.0 - 14.0VDC
• GD443X: 4.2 - 5.25VDC
Operating (typical)
• GD441X- 170ma
• GD443X - 160ma
Operating (max)
• GD441X- 385ma
• GD443X - 350ma
Idle/standby (typical)
• GD441X - 65ma
• GD443X - 65ma
Performance Characteristics
Light Source LEDs
Roll (Tilt) Tolerance Up to ± 180°
Pitch Tolerance ± 40°
Skew (Yaw) Tolerance ± 40°
Print Contrast Minimum 25% minimum reflectance
Page 30
Technical Specifications
26 Gryphon™ I GD44XX
Depth of Field (Typical)
a
a. 13 mils DOF based on EAN. All other 1D codes are Code 39. All labels grade A, typical environmental light,
20°C, label inclination 10°
Symbology SR: HD:
Code 39
5mil: 1.6” -7.5” (4.0 -19cm) 10mil: 0.4” - 11..8” (1.0 - 30cm) 20mil: up to 17.7” (up to 45cm)
3mil: 0.9” - 3.6” (2.4 - 9.1cm) 5 mil: 0.3” - 4.5” (0.8 -11.3cm)
EAN
7.5mil: 0.5” - 10.6” (2.0 - 27cm) 13mil: 0.6” - 15.7” (1.5 - 40cm)
7.5mil: 0” - 5” (0 - 12.7cm) 13mil: .43” - 6.8” (1.1- 17.2cm)
PDF-417
6.6mil: 1.0” - 5.9” (2.5 - 15cm) 10mil: 0.2” - 8.6” (0.5 - 22cm) 15mil: 0.6” - 13.4” (1.5 - 34cm)
4mil: 0.7” - 2.7” (1.8 - 6.8cm)
6.6mil: 0.1” - 4.4” (0.1 - 11.2cm) 10mil: 0” - 5.6” (0 - 14.3cm)
DataMatrix
10mil: 0.8” to 6.3” (2.0 - 16cm) 15mil: 0” to 9.3” (0 - 23.6cm)
5mil: 1.1” - 2.4” (2.8-6.1cm)
QR Code
10mil: 1.2” to 4.9” (3.0 - 12.5cm) 15mil: 0.4” to 7.5” (1.0 - 19cm)
6.7mil: 0.8” - 1.7” (2.1 - 4.2cm)
Minimum Element Width
Standard Range:
1D Min Resolution = 4 mil PDF-417 Min Resolution = 5 mil Datamatrix Min Resolution = 7 mil
High Density:
1D Min Resolution = 2.5 mil PDF-417 Min Resolution = 4 mil Datamatrix Min Resolution = 5 mil
Page 31
Technical Specifications
Quick Reference Guide 27
Decode Capability
1D Bar Codes
UPC/EAN/JAN (A, E, 13, 8); UPC/EAN/JAN (including P2 /P5); UPC/EAN/JAN (including; ISBN / Bookland & ISSN); UPC/EAN Coupons; Code 39 (including full ASCII); Code 39 Trioptic; Code39 CIP (French Pharmaceutical); LOGMARS (Code 39 w/ standard check digit enabled); Danish PPT; Code 32 (Italian Pharmacode 39); Code 128; Code 128 ISBT; Interleaved 2 of 5 ; Standard 2 of 5; Interleaved 2 of 5 CIP (HR); Industrial 2 of 5; Discrete 2 of 5; Datalogic 2 of 5 (China Post Code/Chinese 2 of 5); IATA 2of5 Air cargo code; Code 11; Codabar; Codabar (NW7); ABC Coda­bar; EAN 128; Code 93 ; MSI; PZN; Plessey; Anker Plessey; GS1 DataBar Omnidirectional; GS1 DataBar Limited; GS1 DataBar Expanded; GS1 DataBar Truncated; DATABAR Expanded Coupon.
2D / Stacked Codes
The Gryphon I GD44XX scanner is capable of decoding the following sybmologies using multi­ple frames (i.e. Multi-Frame Decoding):
Datamatrix; Inverse Datamatrix; Datamatrix is configurable for the following parameters:; Normal or Inverted; Square or Rectangular Style; Data length (1 - 3600 characters); Maxicode; QR Codes (QR, Micro QR and Multiple QR Codes); Aztec; Postal Codes - (Australian Post; Japa­nese Post; KIX Post; Planet Code; Postnet; Royal Mail Code (RM45CC); Intelligent Mail Barcode (IMB); Sweden Post; Portugal Post); LaPoste A/R 39; 4-State Canada; PDF-417; MacroPDF; Micro PDF417; GS1 Composites (1 - 12); Codablock F; French CIP13
a
; GS1 DataBar Stacked; GS1 DataBar Stacked Omnidirectional; GS1 DataBar Expanded Stacked; GSI Databar Composites; Chinese Sensible Code; Inverted 2D codes
b
.
a
It is acceptable to handle this with ULE
b
The SW can apply the Normal/Reverse Decoding Control to the following symbologies: Datamatrix, QR,
Micro QR, Aztec and Chinese Sensible Code.
Interfaces Supported
USB Com Std., USB Keyboard, USB
See page 8 for a listing of available interface options.
User Environment
Operating Temperature 32° to 131° F (0° to 55° C)
Storage Temperature -4° to 158° F (-20° to 70° C)
Humidity
Operating: 5% to 90% relative humidity, non-condensing
Drop Specifications
Scanner withstands 18 drops from 1.8 meters (6.0 feet) to concrete
Ambient Light Immunity Up to 100,000 Lux
Contaminants Spray/rain Dust/ particulates
IEC 529-IP52
Page 32
LED and Beeper Indications
28 Gryphon™ I GD44XX
LED and Beeper Indications
The reader’s beeper sounds and its LED illuminates to indicate various functions or errors on the reader. An optional “Green Spot” also performs useful functions. The following tables list these indications. One exception to the behaviors listed in the tables is that the reader’s functions are programmable, and so may or may not be turned on. For example, certain indications such as the power-up beep can be disabled using programming bar code labels.
ESD Level 16 KV
Regulatory
Electrical Safety UL 60950, CSA C22.2 No. 60950, IEC 60950
EMI/RFI
North America (FCC) : Part 15 Class B; Canada ( IC) : ICES­003 Class B; Russia ( Gost); European Union EMC Directive; VCCI-Japan; Korean KCC; Taiwan EMC (BSMI); Australia (ACMA)
Laser Class Safety
IEC Class 2 Radiation 1 mW Avg., Emitted wavelength 650 nm, 12ms pulse, Beam Divergence 8.4 deg x 8.1 deg (“plus” pattern)
Complies with FDA performance standards for laser products except for deviations pursuant to Laser Notice No. 50, dated June 24, 2007.
Indicator Description LED Beeper
Power-up Beep
The reader is in the process of power­ing-up.
Reader beeps four times at highest frequency and vol­ume upon power­up.
Good Read Beep
A label has been successfully scanned by the reader.
LED behavior for this indication is configurable via the feature “Good Read: When to Indicate” (see the PRG for information.)
The reader will beep once at cur­rent frequency, volume, mono/bi­tonal setting and duration upon a successful label scan.
Page 33
LED and Beeper Indications
Quick Reference Guide 29
ROM Failure
There is an error in the reader's soft­ware/programming
Flashes
Reader sounds one error beep at high­est volume.
Limited Scanning Label Read
Indicates that a host connection is not established.
N/A
Reader 'chirps' six times at the high­est frequency and current volume.
Reader Active Mode
The reader is active and ready to scan.
The LED is lit
steadily
a
N/A
Reader Disabled
The reader has been disabled by the host.
The LED blinks continuously
N/A
Green Spot
a
flashes momentarily
Upon successful read of a label, the software shall turn the green spot on for the time speci­fied by the config­ured value.
N/A N/A
Image Capture
When ready to cap­ture image
Blue light
flashes 2 times
when updating
N/A
a
Except when in sleep mode or when a Good Read LED Duration other than 00 is selected
Indicator Description LED Beeper
Page 34
LED and Beeper Indications
30 Gryphon™ I GD44XX
Programming Mode
-
The following indications ONLY occur
when the reader is in Programming Mode
.
INDICATION DESCRIPTION LED BEEPER
Label Program­ming Mode Entry
A valid programming label has been scanned.
LED blinks
continuously
Reader sounds four low fre­quency beeps.
Label Program­ming Mode Rejec­tion of Label
A label has been rejected.
N/A
Reader sounds three times at lowest fre­quency and cur­rent volume.
Label Program­ming Mode Acceptance of Partial Label
In cases where multi­ple labels must be scanned to program one feature, this indica­tion acknowledges each portion as it is suc­cessfully scanned.
N/A
Reader sounds one short beep at highest fre­quency and cur­rent volume.
Label Program­ming Mode Acceptance of Programming
Configuration option(s) have been successfully programmed via labels and the reader has exited Programming Mode.
N/A
Reader sounds one high fre­quency beep and 4 low frequency beeps followed by reset beeps.
Label Program­ming Mode Can­cel Item Entry
Cancel label has been scanned.
N/A
Reader sounds two times at low frequency and current volume.
Page 35
Error Codes
Quick Reference Guide 31
Error Codes
Upon startup, if the reader sounds a long tone, this means the reader has not passed its automatic Selftest and has entered FRU (Field Replaceable Unit) isolation mode. If the reader is reset, the sequence will be repeated. Press and release the trig­ger to hear the FRU indication code.
The following table describes the LED flashes/beep codes as­sociated with an error found.
Number of
LED Flashes/
Beeps
Error Corrective Action
1 Configuration
Contact Helpdesk for
assistance
2Interface PCB
6Digital PCB
11 Imager
Page 36
Cleaning
32 Gryphon™ I GD44XX
Cleaning
Exterior surfaces and scan windows exposed to spills, smudges or debris accumulation require periodic cleaning to ensure best performance during scanning operations.
Always use a soft, lint-free cloth or lens tissue dampened with isopropyl alcohol (or equivalent) or water-based window cleaner. A cotton swab may be used in hard-to-reach areas.
CAUTION
Do not use abrasive cleansing agents or abrasive pads to clean scan windows or plastics.
Do not spray or pour liquids directly onto the unit.
Page 37
Regulatory Information
Quick Reference Guide 33
Regulatory Information
All models are designed to be compliant with rules and regu­lations in locations they are sold and will be labeled as re­quired.
Any changes or modifications to equipment, not expressly ap­proved by Datalogic could void the user's authority to operate the equipment.
Statement of Agency Compliance
This device complies with part 15 of the FCC Rules. Opera­tion is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
FCC Class B Compliance Statement
The user is cautioned that changes or modifications not ex­pressly approved by the part responsible for compliance could void the user’s authority to operate the equipment.
This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential instal­lation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interfer­ence will not occur in a particular installation. If this equip­ment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the inter­ference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit dif­ferent from that to which the receiver is connected.
Consult the dealer or an experienced radio or televi­sion technician for help.
Page 38
Regulatory Information
34 Gryphon™ I GD44XX
FCC RF Radiation Exposure Statement
To comply with FCC RF exposure compliance requirements, for mobile configurations, a separation distance of at least 20 cm must be maintained between the antenna of this device and all persons.
This device must not be co-located or operating in conjunc­tion with any other antenna or transmitter.
Canadian Notice
This equipment does not exceed the Class B limits for radio noise emissions as described in the Radio Interference Regula­tions of the Canadian Department of Communications.
Le present appareil numerique n’emet pas de bruits radioelec­triques depassant les limites applicables aux appareils nume­riques de la classe B prescrites dans le Reglement sur le brouillage radioelectrique edicte par le ministere des Commu­nications du Canada.
Power Supply
This device is intended to be connected to a UL Listed/CSA Certified computer which supplies power directly to the read­er or else be supplied by UL Listed/CSA Certified Power Unit marked “Class 2” or LPS power source rated 5-14V minimum 900mA.
CAUTION
Exposure to Radio-Frequency Radiation
CAUTION
Do not attempt to open or otherwise service any com­ponents in the optics cavity. Opening or servicing any part of the optics cavity by unauthorized personnel may violate laser safety regulations.
Page 39
Regulatory Information
Quick Reference Guide 35
Imager Labeling
Sample labels are shown here to illustrate their location only. Please view the labels on your product for actual details, as they may vary from those depicted.
Aiming System
The Gryphon™ aiming system meets the Class 2 require­ments for laser safety. The laser information is located on the window of the Scanner and is shown below.
N263
See product
manual and
package for
patent listing.
ACCESSORY
LISTED
I.T.E., .3KRU
Scanner Regulatory Label
DO NOT STARE INTO BEAM
See Pkg for patent listing
LASER LIGHT - DO NOT STARE INTO BEAM
CLASS 2 LASER PRODUCT
OUTPUT RADIATION 1 mW AVG.
EMITTED WAVE LENGTH 650 nm 12 ms PULSE
IEC60825-1:2007
CAUTION-CLASS 2 LASER
LIGHT WHEN OPEN
AVOID EXPOSURE-LASER LIGHT
IS EMITTED FROM THIS APERTURE
This product complies with 21CFR 1040.10
and 1040.11 except for deviations pursuant
to Laser Notice No. 50 dated June 24, 2007
Page 40
Regulatory Information
36 Gryphon™ I GD44XX
ENGLISH
The following information is provided to comply with the rules imposed by international authorities and refers to the correct use of your terminal.
STANDARD LASER SAFETY REGULATIONS
This product conforms to the applicable requirements of both CDRH 21 CFR 1040 and EN 60825-1 at the date of manu­facture.
For installation, use and maintenance, it is not necessary to open the device.
IDFE
LA LUCE LASER È VISI­BILE ALL'OCCHIO UMANO E VIENE EMESSA DALLA FINES­TRA INDI­CATA NELLA FIGURA.
DIE LASER-STRAH­LUNG IST FÜR DAS MENSCHLICHE AUGE SICHTBAR UND WIRD AM STRAHLAUS TRITTS­FENSTER AUSGE­SENDET (SIEHE BILD)
LE RAYON LASER EST VISI­BLE À L'OEIL NU ET IL EST ÉMIS PAR LA FENÊTRE DÉSIGNÉE SUR L'ILLUSTRA­TION DANS LA FIGURE
A LUZ LÁSER ES VISIBLE AL OJO HUMANO Y ES EMITIDA POR LA VENTANA INDICADA EN LA FIGURA.
LUCE LASER NON FISSARE IL FASCIO APPAREC­CHIO LASER DI CLASSE 2 MASSIMA POTENZA D'USCITA: LUNGHEZZA D'ONDA EMESSA: CONFORME A EN 60825-1 (2007)
LASERSTRAHLUNG NICHT IN DEN STRAHL BLICKEN PRODUKT DER LASERKLASSE 2 MAXIMALE AUS­GANGSLEISTUNG: WELLENLÄGE: ENTSPR. EN 60825­1 (2007)
RAYON LASER EVITER DE REGARDER LE RAYON APPAR­EIL LASER DE CLASSE 2 PUIS­SANCE DE SOR­TIE: LONGUEUR D'ONDE EMISE: CONFORME A EN 60825-1 (2007)
RAYO LÁSER NO MIRAR FIJO EL RAYO APARATO LÁSER DE CLASE 2 MÁX­IMA POTENCIA DE SALIDA: LONGITUD DE ONDA EMIT­IDA: CONFORME A EN 60825-1 (2007)
WAR NING
Use of controls or adjustments or perfor­mance of procedures other than those speci­fied herein may result in exposure to hazardous visible laser light.
Page 41
Regulatory Information
Quick Reference Guide 37
The product utilizes a low-power laser diode. Although staring directly at the laser beam momentarily causes no known bio­logical damage, avoid staring at the beam as one would with any very strong light source, such as the sun. Avoid that the la­ser beam hits the eye of an observer, even through reflective surfaces such as mirrors, etc.
ITALIANO
Le seguenti informazioni vengono fornite dietro direttive delle autorità internazionali e si riferiscono all’uso corretto del ter­minale.
NORMATIVE STANDARD PER LA SICUREZZA LASER
Questo prodotto risulta conforme alle normative vigenti sulla sicurezza laser alla data di produzione: CDRH 21 CFR 1040 e EN 60825-1.
Non si rende mai necessario aprire l’appa-recchio per motivi di installazione, utilizzo o manutenzione.
Il prodotto utilizza un diodo laser a bassa potenza. Sebbene non siano noti danni riportati dall’occhio umano in seguito ad una esposizione di breve durata, evitare di fissare il raggio laser così come si eviterebbe qualsiasi altra sorgente di luminosità intensa, ad esempio il sole. Evitare inoltre di dirigere il raggio laser negli occhi di un osservatore, anche attraverso superfici riflettenti come gli specchi.
DEUTSCH
Die folgenden Informationen stimmen mit den Sicherheit­shinweisen überein, die von internationalen Behörden aufer­legt wurden, und sie beziehen sich auf den korrekten Gebrauch vom Terminal.
NORM FÜR DIE LASERSICHERHEIT
Dies Produkt entspricht am Tag der Herstellung den gültigen EN 60825-1 und CDRH 21 CFR 1040 Normen für die La­sersicherheit.
ATTENZIONE
L'utilizzo di procedure o regolazioni differenti da quelle descritte nella documentazione può provocare un'esposizione pericolosa a luce laser visibile.
Page 42
Regulatory Information
38 Gryphon™ I GD44XX
Es ist nicht notwendig, das Gerät wegen Betrieb oder Installa­tions-, und Wartungs-Arbeiten zu öffnen.
Der Produkt benutzt eine Laserdiode. Obwohl zur Zeit keine Augenschäden von kurzen Einstrahlungen bekannt sind, sollten Sie es vermeiden für längere Zeit in den Laserstrahl zu schauen, genauso wenig wie in starke Lichtquellen (z.B. die Sonne). Vermeiden Sie es, den Laserstrahl weder gegen die Au­gen eines Beobachters, noch gegen reflektierende Oberflächen zu richten.
FRANÇAIS
Les informations suivantes sont fournies selon les règles fixées par les autorités internationales et se réfèrent à une correcte utilisation du terminal.
NORMES DE SECURITE LASER
Ce produit est conforme aux normes de sécurité laser en vi­gueur à sa date de fabrication: CDRH 21 CFR 1040 et EN 60825-1.
Il n’est pas nécessaire d’ouvrir l’appareil pour l’installation, l’utilisation ou l’entretien.
Le produit utilise une diode laser. Aucun dommage aux yeux humains n’a été constaté à la suite d’une exposition au rayon laser. Eviter de regarder fixement le rayon, comme toute autre source lumineuse intense telle que le soleil. Eviter aussi de di­riger le rayon vers les yeux d’un observateur, même à travers des surfaces réfléchissantes (miroirs, par exemple).
ACHTUNG
Jegliche Änderungen am Gerät sowie Vorge­hensweisen, die nicht in dieser Betriebsanlei­tung beschreiben werden, können ein gefährliches Laserlicht verursachen.
AT T EN T I ON
L'utilisation de procédures ou réglages dif­férents de ceux donnés ici peut entraîner une dangereuse exposition à lumière laser visible.
Page 43
Regulatory Information
Quick Reference Guide 39
ESPAÑOL
Las informaciones siguientes son presentadas en conformidad con las disposiciones de las autoridades internacionales y se re­fieren al uso correcto del terminal.
NORMATIVAS ESTÁNDAR PARA LA SEGURIDAD LÁSER
Este aparato resulta conforme a las normativas vigentes de se­guridad láser a la fecha de producción: CDRH 21 CFR 1040 y EN 60825-1.
No es necesario abrir el aparato para la instalación, la uti­lización o la manutención.
El aparato utiliza un diodo láser a baja potencia. No son noto­rios daños a los ojos humanos a consecuencia de una ex­posición de corta duración. Eviten de mirar fijo el rayo láser así como evitarían cualquiera otra fuente de luminosidad intensa, por ejemplo el sol. Además, eviten de dirigir el rayo láser hacia los ojos de un observador, también a través de superficies re­flectantes como los espejos.
AT E NC I ÓN
La utilización de procedimientos o regulaciones diferentes de aquellas describidas en la docu­mentación puede causar una exposición pelig­rosa a la luz láser visible.
CAUTION
The Gryphon™ Handheld Reader is not user-ser­viceable. Opening the case of the unit can cause internal damage and will void the warranty.
Page 44
Regulatory Information
40 Gryphon™ I GD44XX
WEEE Statement
English
For information about the disposal of Waste Electrical and Electronic Equipment (WEEE), please refer to the website at www.scanning.datalogic.com.
Italian
Per informazioni sullo smaltimento delle apparecchiature elettriche ed elettroniche consultare il sito Web www.scanning.datalogic.com.
French
Pour toute information relative à l’élimination des déchets électroniques (WEEE), veuillez consulter le site internet www.scanning.datalogic.com.
German
Informationen zur Entsorgung von Elektro- und Elektronik- Altgeräten (WEEE) erhalten Sie auf der Webseite www.scanning.datalogic.com.
Spanish
Si desea información acerca de los procedimientos para el desecho de los residuos del equipo eléctrico y electrónico (WEEE), visite la página Web www.scanning.datalogic.com.
Portuguese
Para informações sobre a disposição de Sucatagem de Equipamentos Elétricos e Eletrônicos (WEEE -Waste Electrical and Electronic Equipment), consultar o site web www.scanning.datalogic.com.
Chinese
有关处理废弃电气电子设备 (WEEE) 的信息, 请参考 Datalogic 公司的网站 www.scanning.datalogic.com/。
Japanese
廃電気電子機器 (WEEE) の処理についての関連事項は Datalogic のサイト www.scanning.datalogic.com をご参照下さ
い。
Waste Electrical and Electronic Equipment (WEEE) Statement
Page 45
Warranty
Quick Reference Guide 41
Warranty
Datalogic warrants to Customer that Datalogic's products will be free from defects in materials and workmanship for a period of one year from product shipment. This war­ranty does not extend to batteries and cables. As consumable items batteries and cables carry a 90 day warranty from time of purchase for DOA (dead on arrival) defects. In order to obtain service under this Warranty, Customer must notify Datalogic of the claimed defect before the expiration of the Warranty period and obtain from Data­logic a return authorization number for return of the product to designated Datalogic service center. If Datalogic determines Customer’s claim is valid, Datalogic will repair or replace product without additional charge for parts and labor. Customer shall be responsible for packaging and shipping the product to the designated Datalogic ser­vice center, with shipping charges prepaid. Datalogic shall pay for the return of the product to Customer if the shipment is to a location within the country in which the Datalogic service center is located. Customer shall be responsible for paying all ship­ping charges, duties, taxes, and any other charges for products returned to any other locations. Warranty is subject to the limitations and exclusions set forth in the paragraphs that follow. WARRANTY SET FORTH ABOVE IS IN LIEU OF ANY OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING MERCHANTABILITY AND FITNESS.
Exclusions
Warranty coverage shall not apply to any claimed defect, failure or damage which Datalogic determines was caused by: improper use of product; failure to provide product maintenance, including but not limited to cleaning of the upper window in accordance with product manual; installation or service of product by other than Dat­alogic representatives; use of product with any other instrument, equipment or appa­ratus; modification or alteration of product. External cables and replacement of upper window/cartridge due to scratching, stains or other degradation will not be covered under the Warranty. External power supplies returned for service must be accompa­nied by the original product for performance of service.
Limitation of Liability
Datalogic's REPAIR OR REPLACEMENT OF DEFECTIVE PRODUCT AS SET FORTH ABOVE IS THE CUSTOMER’S SOLE AND EXCLUSIVE REMEDY ON ACCOUNT OF CLAIMS OF BREACH OF WARRANTY OR PRODUCT DEFECT. UNDER NO CIRCUMSTANCES WILL Dat­alogic BE LIABLE TO CUSTOMER OR ANY THIRD PARTY FOR ANY LOST PROFITS, OR ANY INCIDENTAL, CONSEQUENTIAL IN-DIRECT, SPECIAL OR CONTINGENT DAMAGES REGARDLESS OF WHETHER Datalogic HAD ADVANCE NOTICE OF THE POSSIBILITY OF SUCH DAMAGES.
Assignment
Customer may not assign or otherwise transfer its rights or obligations under War­ranty except to a purchaser or transferee of product. No attempted assignment or transfer in violation of this provision shall be valid or binding upon Datalogic.
Risk of Loss
Customer shall bear risk of loss or damage for product in transit to Datalogic. Data­logic shall assume risk of loss or damage for product in Datalogic's possession or product being returned to Customer by Datalogic, except such loss or damage as may be caused by the negligence of Customer, its agents or employees. In the absence of specific written instructions for the return of product to Customer, Datalogic will select the carrier, but Datalogic shall not thereby assume any liability in connection with the return shipment.
Page 46
Ergonomic Recommendations
42 Gryphon™ I GD44XX
Ergonomic Recommendations
Reduce or eliminate repetitive motion
Maintain a natural position
Reduce or eliminate excessive force
Keep objects that are used frequently within easy reach
Perform tasks at correct heights
Reduce or eliminate vibration
Reduce or eliminate direct pressure
Provide adjustable workstations
Provide adequate clearance
Provide a suitable working environment
Improve work procedures.
Services and Support
Datalogic provides several services as well as technical support through its website. Log on to
www.scanning.datalogic.com
and click on the
links indicated for further information.
Products
Search through the links to arrive at your product page where you can download specific
Manuals
and
Software & Utilities
, including:
Datalogic Aladdin™
, a multi-platform utility program that allows device configuration using a PC. It provides RS-232 interface configuration as well as configuration bar code printing.
Service & Support
Technical Support
- Product documentation and program­ming guides and Technical Support Department in the world
Service Programs
- Warranty Extensions and Maintenance
Agreements
Repair Services
- Flat Rate Repairs and Return Material
Authorization (RMA) Repairs
Downloads
– Manuals & Documentation, Data Sheets,
Product Catalogues, etc.
Contact Us
Information Request Form and Sales & Service Network
CAUTION
In order to avoid or minimize the potential risk of ergo­nomic injury follow the recommendations below. Con­sult with your local Health & Safety Manager to ensure that you are adhering to your company’s safety pro­grams to prevent employee injury.
Page 47
dichiara che declares that the déclare que le bescheinigt, daß das Gerät declare que el
Gryphon GD4400; Barcode Reader
sono conformi alle Direttive del Consiglio Europeo sottoelencate: are in conformity with the requirements of the European Council Directives listed below: sont conformes aux spécifications des Directives de l'Union Européenne ci-dessous: den nachstehenden angeführten Direktiven des Europäischen Rats: cumple con los requisitos de las Directivas del Consejo Europeo, según la lista siguiente:
2004/108/EC EMC Directive
2006/95/EC Low Voltage Directive
Basate sulle legislazioni degli Stati membri in relazione alla compatibilità elettromagnetica ed alla sicurezza dei prodotti. On the approximation of the laws of Member States relating to electromagnetic compatibility and product safety. Basée sur la législation des Etats membres relative à la compatibilité électromagnétique et à la sécurité des produits. Über die Annäherung der Gesetze der Mitgliedsstaaten in bezug auf elektromagnetische Verträglich­keit und Produktsicherheit entsprechen. Basado en la aproximación de las leyes de los Países Miembros respecto a la compatibilidad electro­magnética y las Medidas de seguridad relativas al producto.
Questa dichiarazione è basata sulla conformità dei prodotti alle norme seguenti: This declaration is based upon compliance of the products to the following standards: Cette déclaration repose sur la conformité des produits aux normes suivantes: Diese Erklärung basiert darauf, daß das Produkt den folgenden Normen entspricht: Esta declaración se basa en el cumplimiento de los productos con las siguientes normas:
EC-65 Rev.: 0 Pag.: 1 di 1
Datalogic Scanning, Inc. 959 Terry St. Eugene, OR 97402 USA
e tutti i suoi modelli and all its models et tous ses modèles und seine Modelle y todos sus modelos
EN 55022 (CLASS B ITE ), SEPTEMBER 2006: AMMENDMENT A1: OCTOBER 2007
L
IMITS AND METHODS OF MEASUREMENTS OF RADIO DISTURBANCE
CHARACTERIS TICS OF INFORMATION TECHNOLO GY EQUIPMENTS
EN 55024, SEPTEMBER 1998 : A
MENDMENT A2, JUNE 2003
I
NFORMATION TECHNOLOGY EQUIPMENT
IMMUNITY CHARACTERISTICS LIMITS AND METHODS OF MEASUREMENT
EN 60950-1, APRIL 2006+A11:2009 :
INFORMATION TECHNOLOGY EQUIPMENT - SAFETY ­PART 1 : GENERAL REQUIREMENTS
EUGENE, OREGON USA FEBRUARY 18, 2011
Brad West Vice President, Supply Chain Operations
11
DECLARATION OF CONFORMITY
Page 48
Australia
Datalogic Scanning Pty Ltd Telephone: [61] (2) 9870 3200 australia.scanning@datalogic.com
France and Benelux
Datalogic Scanning SAS Telephone: [33].01.64.86.71.00 france.scanning@datalogic.com
Germany
Datalogic Scanning GmbH Telephone: 49 (0) 61 51/93 58-0 germany.scanning@datalogic.com
India
Datalogic Scanning India Telephone: 91- 22 - 64504739 india.scanning@datalogic.com
Italy
Datalogic Scanning SpA Telephone: [39] (0) 39/62903.1 italy.scanning@datalogic.com
Japan
Datalogic Scanning KK Telephone: 81 (0)3 3491 6761 japan.scanning@datalogic.com
Latin America
Datalogic Scanning, Inc Telephone: (305) 742-2206 latinamerica.scanning@datalogic.com
Singapore
Datalogic Scanning Singapore PTE LTD Telephone: (65) 6435-1311 singapore.scanning@datalogic.com
Iberia
Datalogic Scanning SAS Sucursal en España Telephone: 34 91 746 28 60 spain.scanning@datalogic.com
United Kingdom
Datalogic Scanning LTD Telephone: 44 (0) 1582 791700 uk.scanning@datalogic.com
Datalogic Scanning, Inc.
959 Terry Street Eugene, OR 97402 USA Telephone: (541) 683-5700 Fax: (541) 345-7140
©2010-2011 Datalogic Scanning, Inc. 820033514 (Rev B) Oct-2011
www.scanning.datalogic.com
Loading...