Datalogic Gryphon, Gryphon D230, Gryphon D130, Gryphon D130-LR Quick Reference
Gryphon™
Dx30 Readers
QUICK REFERENCE
820001611 (Rev. B)
UPDATES AND LANGUAGE AVAILABILITY
UK/US
The latest drivers and documentation updates for this product
are available on Internet.
Log on to : www.datalogic.com
Su Internet sono disponibili le versioni aggiornate di driver e
documentazione di questo prodotto. Questo manuale è
disponibile anche nella versione italiana.
Collegarsi a : www.datalogic.com
Les versions mises à jour de drivers et documentation de ce
produit sont disponibles sur Internet. Ce manuel est aussi
disponible en version française.
Cliquez sur : www.datalogic.com
Im Internet finden Sie die aktuellsten Versionen der Treiber und
Dokumentation von diesem Produkt. Die deutschsprachige
Version dieses Handbuches ist auch verfügbar.
Adresse : www.datalogic.com
En Internet están disponibles las versiones actualizadas de los
drivers y documentación de este producto. También está
disponible la versión en español de este manual.
Dirección Internet : www.datalogic.com
I
F
D
E
USING GRYPHON™ DX30 READERS
Gryphon™ guns automatically scan barcodes at a distance.
Simply aim and pull the trigger. Code scanning is performed
along the center of the light bar emitted from the reading
window. This bar must cover the entire code.
Successful scanning is obtained by tilting the scanner with
respect to the barcode to avoid direct reflections which impair
the reading performance, see the figure above.
Successful reading is signaled by an audible tone plus a
good-read green spot.
CONNECTIONS
RS232
USB
(if required)
IBM USB POS
PEN
WEDGE
WEDGE
DISCONNECTING THE CABLE
INTERFACE SELECTION
Follow the procedure to configure the interface required by your
application.
- USB Interface
- RS232 Interface
- Wedge Interface
- Pen Interface
USB INTERFACE CONFIGURATION
The USB interface is compatible with:
Windows 98 (and later) IBM POS for Windows
Mac OS 8.0 (and later) 4690 Operating System
START-UP
As with all USB devices, upon connection, the Host performs
several checks by communicating with the Gryphon™. During
this phase the green LED on the Gryphon™ reader blinks and
normal operations are suspended. Two basic conditions must
be met before Gryphon™ is ready to read codes, the correct
USB driver must be loaded and sufficient power must be
supplied to the reader.
For all systems, the correct USB driver for the default USB-KBD
interface is included in the Host Operating System and will
either be loaded automatically or will be suggested by the O.S.
and should therefore be selected from the dialog box (the first
time only).
If the Host supplies sufficient power to the reader, the start-up
phase ends correctly, the green LED stops blinking and the
reader emits the beep OK signal.
If the Host does not supply sufficient power to the reader, a
dialog box will appear on the Host and the reader will be
blocked (green LED continues blinking). In this case,
disconnect the USB cable at the Host
blinking), connect and power-up an external supply to USB
cable then
dialog box. The reader emits the beep OK signal. You can now
read codes. At this point you can read the USB interface
configuration code according to your application. Load drivers
from the O.S. (if requested). When configuring the USB-COM
interface, the relevant files and drivers must be installed from
the USB Device Installation software which can be downloaded
from the web site http://www.datalogic.com
The reader is ready.
reconnect the USB cable to the Host and close the
(green LED stops
.
(
)
Green LED off
BEEP OK
Disconnect reader
at Host
Connect external
power supply to
cable and power up
Reconnect reader
cable to Host and
close dialog box
YES
Connect
Gryphon™ to Host
Load drivers
if requested
Does a dialog
box appear
warning that Bus
power is not
sufficient?
NO
Green LED off - BEEP OK
Select desired USB
interface code
(USB-KBD is default)
Load drivers
(if requested)
Read test codes.
Reader is READY
Green LED blinks
Successive start-ups will automatically recognize the previously
loaded drivers. If external power is used, verify that external
power is already supplied.
Successive Start-Ups
First Start-Up
Connect Gryphon™
to Host
Green LED blinks
BEEP OK
Disconnect reader
at Host
Connect external
power supply to
cable and power up
Reconnect reader
cable to Host and
close dialog box
YES
Does a dialog box
that Bus power is
Read test codes.
Reader is READY
appear warning
not sufficient?
NO
Green LED off - BEEP OK
USB INTERFACE SELECTION
USB-KBD
Ì$+UA03$-:Î
USB-KBD-ALT-MODE
Ì$+UA04$-@Î
USB-KBD-APPLE
Ì$+UA05$-FÎ
USB-COM*
Ì$+UA02$-4Î
USB-IBM-Table Top
Ì$+UA00$-(Î
USB-IBM-Hand Held
Ì$+UA01$-.Î
* When configuring USB-COM, the relevant files and drivers
must be installed from the USB Device Installation software,
which can be downloaded from the web site
http://www.datalogic.com
.
Loading...