Datalogic GPS4400 User Manual

Datalogic ADC, Inc.

Gryphon™ I GPS4400

On-Counter Presentation Scanner

Regulatory Addendum

850019714 (Rev. A) April 2016

Bottom of Scanner

959 Terry Street
Eugene, OR 97402
USA
Telephone: [phone]
Fax: [phone]

Regulatory Information

All versions of the reader are designed to be compliant with rules and regu­lations in locations they are sold and will be labeled as required.

Any changes or modifications to equipment, not expressly approved by
Datalogic could void the user's authority to operate the equipment.

Power Supply

This device is intended to be connected to a UL Listed/CSA Certified
computer which supplies power directly to the reader or else be sup­plied by UL Listed/CSA Certified Power Unit marked “Class 2” or LPS
power source rated 5VDV, minimum 250mA.

©2013-2015 Datalogic, Inc.

An Unpublished Work - All rights reserved. No part of the contents of this
documentation or the procedures described therein may be reproduced or
transmitted in any form or by any means without prior written permission
of Datalogic ADC, Inc. or its subsidiaries or affiliates ("Datalogic" or “Data­logic ADC”). Owners of Datalogic products are hereby granted a non-exclu­sive, revocable license to reproduce and transmit this documentation for
the purchaser's own internal business purposes. Purchaser shall not
remove or alter any proprietary notices, including copyright notices, con­tained in this documentation and shall ensure that all notices appear on
any reproductions of the documentation.
Should future revisions of this manual be published, you can acquire
printed versions by contacting your Datalogic representative. Electronic
versions may either be downloadable from the Datalogic website
(www.datalogic.com) or provided on appropriate media. If you visit our
website and would like to make comments or suggestions about this or
other Datalogic publications, please let us know via the "Contact Datalogic"
page.

Disclaimer

Datalogic has taken reasonable measures to provide information in this
manual that is complete and accurate, however, Datalogic reserves the
right to change any specification at any time without prior notice.
Datalogic and the Datalogic logo are registered trademarks of Datalogic
S.p.A. in many countries, including the U.S.A. and the E.U. All other brand
and product names may be trademarks of their respective owners.

Statement of Agency Compliance

This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) this device may not cause harmful inter­ference, and (2) this device must accept any interference received, including
interference that may cause undesired operation.

FCC Class B Compliance Statement

The user is cautioned that changes or modifications not expressly
approved by the part responsible for compliance could void the user’s
authority to operate the equipment.

This equipment has been tested and found to comply with the limits for a
Class B digital device pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in
a residential installation. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particu­lar installation. If this equipment does cause harmful interference to radio
or television reception, which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the interference by one
or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.

• Consult the dealer or an experienced radio or television technician
for help.

Reader Labeling

The sample labels shown below are for illustrative purposes only.
Please view the labels on your product for actual details, as they may
vary.

Patents

Seewww.patents.datalogic.comforpatentlist.

This product is covered by one or more of the following patents:
Design patents: EP002289512
Utility patents: EP0996284B1, EP0999514B1, EP1128315B1, EP1172756B1,
EP1396811B1, EP1413971B1, EP1828957B1, JP4435343B2, US6478224,
US6512218, US6513714, US6561427, US6808114, US6877664, US6997385,
US7053954, US7234641, US7387246, US7721966, US8245926, US8561906

This document is an addendum to the Quick
Reference Guide (QRG) for this product. See the
QRG for additional product information.

©2013-2015 Datalogic, Inc.• All rights reserved.
Datalogic and the Datalogic logo are registered trade­marks of Datalogic S.p.A. in many countries, including
the U.S.A. and the E.U.

Canadian Notice

This equipment does not exceed the Class B limits for radio noise emis­sions as described in the Radio Interference Regulations of the Canadian
Department of Communications.

Le present appareil numerique n’emet pas de bruits radioelectriques
depassant les limites applicables aux appareils numeriques de la classe B
prescrites dans le Reglement sur le brouillage radioelectrique edicte par le
ministere des Communications du Canada.

Do not attempt to open or otherwise service any components
in the optics cavity. Opening or servicing any part of the optics
cavity by unauthorized personnel may violate laser safety

CAUTION

The CU conformity certification has been achieved; this allows the Product
to bear the Eurasian mark of conformity.

regulations.

Customs Union

www.datalogic.com

CHINA ROHS Table of Restricted Elements

China RoHS

(Pb)

(Hg)

(Cd)

Chromium

(Cr(VI))

biphenyls

(PBB)

diphenyl ethers

(PBDE)

᭷ẘ᭷ᐖ≀峐ᡈඖ⣲

㒊௳ྡ⛠

摭ġ ợ 擱ġ

භ௴撔ġ ከ㹜俼劗ġ ከ㹜Ḵ劗慂ġ

PCB Assembly, Digital

ᮠᆇ⭥䐟ᶯ㓴Ԧ

䀓⸱⭥䐟ᶯ㓴Ԧ

X O O O O O

Cable

⭥㔶

X O O O O O

Power Supply

⭥Ⓚ

X O O O O O

Assembly, Module

ݹᆖ㓴Ԧ

X O O O O O

O ௦⾲Ṉ䥵㒊௳ⓗᡤ᭷ᆒ峐㛸瀌󰵶㇨⏓䘬宍䥵㚱㭺㚱⭛䈑峐⛯ỶḶ󰵶⋶Ṣ㮹ℙ␴⚥ᾉ〗ṏ󰵣悐ᡤ栩ⶫⓗ

ࠓ䓝⫸ᾉ〗ṏ⑩󰵶㚱㭺㚱⭛䈑峐䘬旸濌天㯪˫(SJ/T 11363-2006) 奬⭂䘬旸濌ࠋ

X: ௦⾲Ṉ䥵㒊௳ᡤ⏝ⓗᆒ峐㛸瀌󰵶, ⮳ᑡ᭷୍䰣ᮦᩱ඼ᡤྵⓗ᭷ẘ᭷ᐖ≀峐檀Ḷ󰵶⋶Ṣ㮹ℙ␴⚥ᾉ〗ṏ󰵣悐ᡤ栩ⶫⓗ

ࠓ䓝⫸ᾉ〗ṏ⑩󰵶㚱㭺㚱⭛䈑峐䘬旸濌天㯪˫(SJ/T 11363-2006) 奬⭂䘬旸㔞

EFUP determined by “Look-up Method” (scanner). 䍗ᾅἧ䓐㛇旸⍾⅛Ḷ“㞍堐㱽”㸦㈓㍷Ẓ炸

WEEE Statement

English

For information about the disposal of Waste Electrical and Electronic
Equipment (WEEE), please refer to the website at www.datalogic.com.

Italian

Per informazioni sullo smaltimento delle apparecchiature elettriche ed
elettroniche consultare il sito Web www.datalogic.com.

French

Pour toute information relative à l’élimination des déchets électroniques
(WEEE), veuillez consulter le site internet www.datalogic.com.

German

Informationen zur Entsorgung von Elektro- und Elektronik- Altgeräten
(WEEE) erhalten Sie auf der Webseite www.datalogic.com.

Spanish

Si desea información acerca de los procedimientos para el desecho de los
residuos del equipo eléctrico y electrónico (WEEE), visite la página Web
www.datalogic.com.

Portuguese

Para informações sobre a disposição de Sucatagem de Equipamentos
Elétricos e Eletrônicos (WEEE -Waste Electrical and Electronic Equipment),
consultar o site web www.datalogic.com.

Chinese

有关处理废弃电气电子设备 (

WEEE)

的信息， 请参考

Datalogic

公司的网

站

www.datalogic.com

。

Japanese

廃電気電子機器 (WEEE) の処理についての関連事項は Datalogic のサイト
www.datalogic.com をご参照下さい。

Waste Electrical and Electronic Equipment (WEEE) State­ment

16

Polybrominated

Polybrominated



O O O

Hexavalent

Cadmium

Mercury

Lead

X O O

PCB Assembly, Decoder

PART

The Gryphon™ aiming system meets the Class 2 requirements for laser safety.

Aiming System

IDFE

LA LUCE LASER È VIS­IBILE ALL'OCCHIO
UMANO E VIENE
EMESSA DALLA FINE­STRA INDICATA
NELLA FIGURA.

LUCE LASER NON
FISSARE IL FASCIO
APPARECCHIO LASER
DI CLASSE 2 MAS­SIMA POTENZA
D'USCITA:
LUNGHEZZA D'ONDA
EMESSA:
CONFORME A EN
60825-1 (2007)

The following information is provided to comply with the rules imposed by inter­national authorities and refers to the correct use of your terminal.

STANDARD LASER SAFETY REGULATIONS

This product conforms to the applicable requirements of both CDRH 21 CFR
1040 and EN 60825-1 at the date of manufacture.
For installation, use and maintenance, it is not necessary to open the device.

Le seguenti informazioni vengono fornite dietro direttive delle autorità inter­nazionali e si riferiscono all’uso corretto del terminale.

NORMATIVE STANDARD PER LA SICUREZZA LASER

Questo prodotto risulta conforme alle normative vigenti sulla sicurezza laser alla
data di produzione: CDRH 21 CFR 1040 e EN 60825-1.
Non si rende mai necessario aprire l’appa-recchio per motivi di installazione, uti­lizzo o manutenzione.

DIE LASER-STRAHLUNG
IST FÜR DAS MENSCHLI­CHE AUGE SICHTBAR
UND WIRD AM
STRAHLAUS TRITTSFEN­STER AUSGESENDET
(SIEHE BILD)

LASERSTRAHLUNG
NICHT IN DEN STRAHL
BLICKEN PRODUKT DER
LASERKLASSE 2 MAXI­MALE AUSGANGSLEIS­TUNG:
WELLENLÄGE:
ENTSPR. EN 60825-1
(2007)

L'utilizzo di procedure o regolazioni differenti da
quelle descritte nella documentazione può provocare
un'esposizione pericolosa a luce laser visibile.

LE RAYON LASER EST
VISIBLE À L'OEIL NU
ET IL EST ÉMIS PAR
LA FENÊTRE
DÉSIGNÉE SUR
L'ILLUSTRATION
DANS LA FIGURE

RAYON LASER EVITER
DE REGARDER LE
RAYON APPAREIL
LASER DE CLASSE 2
PUISSANCE DE SOR­TIE:
LONGUEUR D'ONDE
EMISE:
CONFORME A EN
60825-1 (2007)

ENGLISH

ITALIANO

A LUZ LÁSER ES VISI­BLE AL OJO HUMANO
Y ES EMITIDA POR LA
VENTANA INDICADA
EN LA FIGURA.

RAYO LÁSER NO
MIRAR FIJO EL RAYO
APARATO LÁSER DE
CLASE 2 MÁXIMA
POTENCIA DE SAL­IDA:
LONGITUD DE ONDA
EMITIDA:
CONFORME A EN
60825-1 (2007)

ATTENZIONE

Il prodotto utilizza un diodo laser a bassa potenza. Sebbene non siano noti danni
riportati dall’occhio umano in seguito ad una esposizione di breve durata, evitare
di fissare il raggio laser così come si eviterebbe qualsiasi altra sorgente di lumi­nosità intensa, ad esempio il sole. Evitare inoltre di dirigere il raggio laser negli
occhi di un osservatore, anche attraverso superfici riflettenti come gli specchi.

Die folgenden Informationen stimmen mit den Sicherheitshinweisen überein,
die von internationalen Behörden auferlegt wurden, und sie beziehen sich auf
den korrekten Gebrauch vom Terminal.

NORM FÜR DIE LASERSICHERHEIT

Dies Produkt entspricht am Tag der Herstellung den gültigen EN 60825-1 und
CDRH 21 CFR 1040 Normen für die Lasersicherheit.
Es ist nicht notwendig, das Gerät wegen Betrieb oder Installations-, und War­tungs-Arbeiten zu öffnen.

Jegliche Änderungen am Gerät sowie Vorgehensweisen,
die nicht in dieser Betriebsanleitung beschreiben
werden, können ein gefährliches Laserlicht verursa-

ACHTUNG

Der Produkt benutzt eine Laserdiode. Obwohl zur Zeit keine Augenschäden von
kurzen Einstrahlungen bekannt sind, sollten Sie es vermeiden für längere Zeit in
den Laserstrahl zu schauen, genauso wenig wie in starke Lichtquellen (z.B. die
Sonne). Vermeiden Sie es, den Laserstrahl weder gegen die Augen eines Beo­bachters, noch gegen reflektierende Oberflächen zu richten.

Les informations suivantes sont fournies selon les règles fixées par les autorités
internationales et se réfèrent à une correcte utilisation du terminal.

NORMES DE SECURITE LASER

Ce produit est conforme aux normes de sécurité laser en vigueur à sa date de
fabrication: CDRH 21 CFR 1040 et EN 60825-1.

chen.

DEUTSCH

FRANÇAIS

Il n’est pas nécessaire d’ouvrir l’appareil pour l’installation, l’utilisation ou l’entre­tien.

L'utilisation de procédures ou réglages différents de
ceux donnés ici peut entraîner une dangereuse exposi­tion à lumière laser visible.

ATTENTION

Le produit utilise une diode laser. Aucun dommage aux yeux humains n’a été con­staté à la suite d’une exposition au rayon laser. Eviter de regarder fixement le
rayon, comme toute autre source lumineuse intense telle que le soleil. Eviter
aussi de diriger le rayon vers les yeux d’un observateur, même à travers des sur­faces réfléchissantes (miroirs, par exemple).

ESPAÑOL

Las informaciones siguientes son presentadas en conformidad con las disposi­ciones de las autoridades internacionales y se refieren al uso correcto del termi­nal.

NORMATIVAS ESTÁNDAR PARA LA SEGURIDAD LÁSER

Este aparato resulta conforme a las normativas vigentes de seguridad láser a la
fecha de producción: CDRH 21 CFR 1040 y EN 60825-1.
No es necesario abrir el aparato para la instalación, la utilización o la
manutención.

La utilización de procedimientos o regulaciones diferentes
de aquellas describidas en la documentación puede cau­sar una exposición peligrosa a la luz láser visible.

ATENCIÓN

El aparato utiliza un diodo láser a baja potencia. No son notorios daños a los ojos
humanos a consecuencia de una exposición de corta duración. Eviten de mirar fijo
el rayo láser así como evitarían cualquiera otra fuente de luminosidad intensa, por
ejemplo el sol. Además, eviten de dirigir el rayo láser hacia los ojos de un obser­vador, también a través de superficies reflectantes como los espejos.

The Gryphon™ Handheld Reader is not user-serviceable.
Opening the case of the unit can cause internal damage and
will void the warranty.

CAUTION

DECLARATION OF CONFORMITY

Datalogic ADC Srl, Via S. Vitalino, 13
Lippo di Calderara di Reno (BO) 40012 Italy

EC-097
Rev.: 3
Pag.: 1 di 1

La presente dichiarazione di conformità è rilasciata sotto la responsabilità esclusiva
di Datalogic ADC Srl per:
This Declaration of Conformity is issued under the sole responsibility of Datalogic ADC

Srl for:
Cette déclaration de conformité est établie sous la seule responsabilité de Datalogic
ADC Srl pour:
Diese Konformitätserklärung wird unter der alleinigen Verantwortung des Datalogic
ADC Srl erteilt für:
Esta declaración de conformidad se expide bajo la exclusiva responsabilidad de
Datalogic ADC Srl para:

GPS4400

e tutti i suoi modelli
and all its models
et tous ses modèles
und seine Modelle
y todos sus modelos

sono conformi alle Direttive del Consiglio Europeo sottoelencate:
are in conformity with the requirements of the European Council Directives listed
below:
sont conformes aux spécifications des Directives de l'Union Européenne ci-dessous:
den nachstehenden angeführten Direktiven des Europäischen Rats:
cumple con los requisitos de las Directivas del Consejo Europeo, según la lista
siguiente:

2014/30/EU — EMC Directive

2011/65/EU — RoHS Directive

Basate sulle legislazioni degli Stati membri in relazione alla compatibilità
elettromagnetica ed alla sicurezza dei prodotti.
On the approximation of the laws of Member States relating to electromagnetic
compatibility and product safety.
Basée sur la législation des Etats membres relative à la compatibilté
électromagnétique et à la sécurité des produits.
Über die Annäherung der Gesetze der Mitgliedsstaaten in bezug auf
elektromagnetische
Verträglichkeit und Produktsicherheit entsprechen.
Basado en la aproximación de las leyes de los Países Miembros respecto a la
compatibilidad electromagnética y las Medidas de seguridad relativas al producto.

Questa dichiarazione è basata sulla conformità dei prodotti alle norme seguenti:
This declaration is based upon compliance of the products to the following standards:
Cette déclaration repose sur la conformité des produits aux normes suivantes:
Diese Erklärung basiert darauf, daß das Produkt den folgenden Normen entspricht:
Esta declaración se basa en el cumplimiento de los productos con las siguientes
normas:

EN 55032, MAY 2015:

EN 55024, N

EN 50581, S

OVEMBER

EPTEMBER

Lippo di Calderara,
April 20th, 2016

2010 :

2012:

E

LECTROMAGNETIC COMPATIBILITY OF MULTIMEDIA EQUIP

MENT

- E

MISSION REQUIREMENTS

I

NFORMATION TECHNOLOGY EQUIPMENT

I

MMUNITY CHARACTERISTICS

L

IMITS AND METHODS OF MEASUREMENT

T

ECHNICAL DOCUMENTATION FOR THE ASSESSMENT OF

E

LECTRICAL AND ELECTRONIC PRODUCTS WITH RESPECT

TO THE RESTRICTION OF HAZARDOUS SUBSTANCES

Ruggero Cacioppo

Product Quality Leader

-