Datadelay PDU1032H-5, PDU1032H-5C4, PDU1032H-5M, PDU1032H-5MC4, PDU1032H-6 Datasheet

PDU1032H

Doc #97045 DATA DELAY DEVICES, INC. 1

12/17/97 3 Mt. Prospect Ave. Clifton, NJ 07013

5-BIT, ECL-INTERFACED
PROGRAMMABLE DELAY LINE
(SERIES PDU1032H)

FEATURES PACKAGES

• Digitally programmable in 32 delay steps

• Monotonic delay-versus-address variation

• Precise and stable delays

• Input & outputs fully 10KH-ECL interfaced & buffered

• Fits 32-pin DIP socket

FUNCTIONAL DESCRIPTION

The PDU1032H-series device is a 5-bit digitally programmable delay line.
The delay, TDA, from the input pin (IN) to the output pin (OUT) depends
on the address code (A4-A0) according to the following formula:

TDA = TD0 + T

INC

* A

where A is the address code, T

INC

is the incremental delay of the device, and TD0 is the inherent delay of

the device. The incremental delay is specified by the dash number of the device and can range from

0.5ns through 20ns, inclusively. The enable pin (ENB) is held LOW during normal operation. When this
signal is brought HIGH, OUT is forced into a LOW state. The address is not latched and must remain
asserted during normal operation.

SERIES SPECIFICATIONS

• Total programmed delay tolerance: 5% or 2ns,
whichever is greater

• Inherent delay (TD0): 5.5ns typical for dash numbers

up to 5, greater for larger #’s

• Setup time and propagation delay:

Address to input setup (T

AIS

): 3.6ns

Disable to output delay (T

DISO

): 1.7ns typical

• Operating temperature: 0° to 70° C

• Temperature coefficient: 100PPM/°C (excludes TD0)

• Supply voltage VEE: -5VDC ± 5%

• Power Dissipation: 615mw typical (no load)

• Minimum pulse width: 20% of total delay

1997 Data Delay Devices

data

delay
devices, inc.



3

1

2
3
4
5
6
7
8
9
10
11

12

24

23
22
21
20
19
18
17
16
15
14

13

N/C

N/C

OUT

GND

ENB

N/C
N/C
N/C

GND

ENB

N/C

IN

N/C

N/C
A2
A1
VEE
A0
N/C
N/C
A4
VEE
A3

N/C

32
31

26
25
24

17

1
2

7
8
9

11

15
16

GND

ENB

A0

VEE

GND

IN

A3

VEE

GND
OUT

A1
A2
GND

A4

PDU1032H-xxC4 SMD
PDU1032H-xxMC4 Mil SMD

PDU1032H-xx DIP
PDU1032H-xxM Mil DIP

PIN DESCRIPTIONS

IN Signal Input
OUT Signal Output
A0-A4 Address Bits
ENB Output Enable
VEE -5 Volts
GND Ground

DASH NUMBER SPECIFICATIONS

Part

Number

Incremental Delay

Per Step (ns)

Total

Delay (ns)

PDU1032H-.5

0.5 ± 0.3 15.5 ± 2.0

PDU1032H-1

1.0 ± 0.5 31 ± 2.0

PDU1032H-2

2.0 ± 0.5 62 ± 3.1

PDU1032H-3

3.0 ± 1.0 93 ± 4.6

PDU1032H-4

4.0 ± 1.0 124 ± 6.2

PDU1032H-5

5.0 ± 1.0 155 ± 7.8

PDU1032H-6

6.0 ± 1.0 186 ± 9.3

PDU1032H-8

8.0 ± 1.0 248 ± 12.4

PDU1032H-10

10.0 ± 1.5 310 ± 15.5

PDU1032H-12

12.0 ± 1.5 372 ± 18.6

PDU1032H-15

15.0 ± 1.5 465 ± 23.2

PDU1032H-20

20.0 ± 2.0 620 ± 31.0

NOTE: Any dash number between .5 and 20

not shown is also available.

PDU1032H

Doc #97045 DATA DELAY DEVICES, INC. 2

12/17/97 Tel: [phone] Fax: [phone] http://www.datadelay.com

APPLICATION NOTES

ADDRESS UPDATE

The PDU1032H is a memory device. As such,
special precautions must be taken when
changing the delay address in order to prevent
spurious output signals. The timing restrictions
are shown in Figure 1.

After the last signal edge to be delayed has
appeared on the OUT pin, a minimum time,
T

OAX

, is required before the address lines can
change. This time is given by the following
relation:

T

OAX

= max { (Ai - A

i-1

) * T

INC

, 0 }

where A

i-1

and Ai are the old and new address
codes, respectively. Violation of this constraint
may, depending on the history of the input signal,
cause spurious signals to appear on the OUT
pin. The possibility of spurious signals persists
until the required T

OAX

has elapsed.

A similar situation occurs when using the ENB
signal to disable the output while IN is active. In
this case, the unit must be held in the disabled
state until the device is able to “clear” itself. This
is achieved by holding the ENB signal high and
the IN signal low for a time given by:

T

DISH

= Ai * T

INC

Violation of this constraint may, depending on
the history of the input signal, cause spurious
signals to appear on the OUT pin. The

possibility of spurious signals persists until the
required T

DISH

has elapsed.

INPUT RESTRICTIONS

There are three types of restrictions on input
pulse width and period listed in the AC
Characteristics table. The recommended
conditions are those for which the delay
tolerance specifications and monotonicity are
guaranteed. The suggested conditions are
those for which signals will propagate through the
unit without significant distortion. The absolute
conditions are those for which the unit will
produce some type of output for a given input.

When operating the unit between the
recommended and absolute conditions, the
delays may deviate from their values at low
frequency. However, these deviations will
remain constant from pulse to pulse if the input
pulse width and period remain fixed. In other
words, the delay of the unit exhibits frequency
and pulse width dependence when operated
beyond the recommended conditions. Please
consult the technical staff at Data Delay Devices
if your application has specific high-frequency
requirements.

Please note that the increment tolerances listed
represent a design goal. Although most delay
increments will fall within tolerance, they are not
guaranteed throughout the address range of the
unit. Monotonicity is, however, guaranteed over
all addresses.

T

DISO

T

OAX

T

AENS

T

ENIS

PW

IN

TD

A

PW

OUT

T

DISH

A4-A0

ENB

IN

OUT

Figure 1: Timing Diagram

A

i-1

A

i

T

AIS