Datadelay MDU28C-45, MDU28C-40, MDU28C-40A1, MDU28C-40B1, MDU28C-40M Datasheet

...
MDU28C
DUAL, HCMOS-INTERFACED
data
3
1
14
I1
VDD
FIXED DELAY LINE (SERIES MDU28C)
delay devices, inc.
FEATURES PACKAGES
I1
Fits standard 8-pin DIP socket
Low profile
Auto-insertable
N/C
GND
1 2
I2
3 4
Input & outputs fully CMOS interfaced & buffered
10 T2L fan-out capability
MDU28C-xx DIP MDU28C-xxA1 Gull-Wing MDU28C-xxB1 J-Lead MDU28C-xxM Military DIP
FUNCTIONAL DESCRIPTION
The MDU28C-series device is a 2-in-1 digitally buffered delay line. The signal inputs (I1-I2) are reproduced at the outputs (O1-O2), shifted in time by an amount determined by the device dash number (See Table). The delay lines function completely independently of each other.
VDD
8
O1
7
N/C
6
O2
5
N/C N/C N/C
N/C
GND
PIN DESCRIPTIONS
I1-I2 Signal Inputs O1-O2 Signal Outputs VDD +5 Volts GND Ground
2
13
3
12
4
11
5
I2
Military SMD MDU28C-xxMD1 MDU28C-xxMD4
10
6
9
7
8
N/C O1 N/C N/C N/C O2
SERIES SPECIFICATIONS
Minimum input pulse width: 100% of total delay
Output rise time: 8ns typical
Supply voltage: 5VDC ± 5%
Supply current: I I
= 40µa typical
CCL
= 45ma typical
CCH
Operating temperature: 0° to 70° C
Temp. coefficient of total delay: 300 PPM/°C
O2O1
100%
100%
VDD GNDI1 I2
Functional block diagram
DASH NUMBER SPECIFICATIONS
Part
Number
MDU28C-10 MDU28C-12 MDU28C-16 MDU28C-20 MDU28C-25 MDU28C-30 MDU28C-35 MDU28C-40 MDU28C-45 MDU28C-50 MDU28C-60 MDU28C-75 MDU28C-100
NOTE: Any dash number between 10 and 100
not shown is also available.
Delay Per
Line (ns)
10 ± 2.0 12 ± 2.0 16 ± 2.0 20 ± 2.0 25 ± 2.0 30 ± 2.0 35 ± 2.0 40 ± 2.0 45 ± 2.2 50 ± 2.5 60 ± 3.0 75 ± 3.7
100 ± 5.0
1997 Data Delay Devices
Doc #97040 DATA DELAY DEVICES, INC. 1
12/12/97 3 Mt. Prospect Ave. Clifton, NJ 07013
MDU28C
APPLICATION NOTES
HIGH FREQUENCY RESPONSE
The MDU28C tolerances are guaranteed for input pulse widths and periods greater than those specified in the test conditions. Although the device will function properly for pulse widths as small as 100% of the total delay and periods as small as 200% of the total delay (for a symmetric input), the delays may deviate from their values at low frequency. However, for a given input condition, the deviation will be repeatable from pulse to pulse. Contact technical support at Data
DEVICE SPECIFICATIONS
TABLE 1: ABSOLUTE MAXIMUM RATINGS
PARAMETER SYMBOL MIN MAX UNITS NOTES
DC Supply Voltage V Input Pin Voltage V Storage Temperature T Lead Temperature T
DD
IN STRG LEAD
Delay Devices if your application requires device testing at a specific input condition.
POWER SUPPLY BYPASSING
The MDU28C relies on a stable power supply to produce repeatable delays within the stated tolerances. A 0.1uf capacitor from VDD to GND, located as close as possible to the VDD pin, is recommended. A wide VDD trace and a clean ground plane should be used.
-0.3 7.0 V
-0.3 VDD+0.3 V
-55 150 C 300 C 10 sec
TABLE 2: DC ELECTRICAL CHARACTERISTICS
PARAMETER SYMBOL MIN TYP MAX UNITS NOTES
High Level Output Voltage V Low Level Output Voltage V High Level Output Current I
Low Level Output Current I High Level Input Voltage V Low Level Input Voltage V Input Current I
(0C to 70C, 4.75V to 5.25V)
OH
OL
OH OL
IH IL
IH
3.98 4.4 V VDD = 5.0, IOH = MAX
0.15 0.26 V VDD = 5.0, IOL = MAX
3.15 V
-4.0 mA
4.0 mA
1.35 V
0.10
µA
VIH = MIN, VIL = MAX VIH = MIN, VIL = MAX
VDD = 5.0
Doc #97040 DATA DELAY DEVICES, INC. 2
12/12/97 Tel: 973-773-2299 Fax: 973-773-9672 http://www.datadelay.com
MDU28C
MDU28C-xx (Commercial DIP)
.500 MAX.
1 2 3 4
.015 TYP.
.070 MAX.
MDU28C-xxM (Military DIP)
.500 MAX.
.520 MAX.
.100
.110
.300
.010 TYP.
.520 MAX.
.100
.110
.300
.050 TYP.
.510 MAX.
.017
.050
.100
.100
.300
.300
.008
.045
.025
.080
.080
.510 MAX.
.017
.050
.100
.100
.650
.008
.005
.065 TYP.
.360 TYP.
.065 TYP.
.018 TYP.
.300±.010
3 Equal spaces
each .100±.010
Non-Accumulative
PACKAGE DIMENSIONS
5678
Lead Material: Nickel-Iron alloy 42
.290 MAX.
TIN PLATE
.010±.002
.280 MAX.
.350 MAX.
1 2 3 4
.300 TYP.
5678
.440 MAX.
.290
.020
MAX.
TYP.
.180
TYP.
.020 TYP.
.010 TYP.
.300 TYP.
.020 TYP.
1 2 3 4
.040 TYP.
5678
.270 TYP.
.300 MAX.
.430 TYP.
.050
TYP.
MDU28C-xxA1 (Commercial Gull-Wing)
1
.300 TYP.
7 8
.200 MAX. (Com) .225 MAX. (Mil)
14
.510 MAX.
.020 TYP.
1 2 3 4
5678
.040 TYP.
.270 TYP.
.350 MAX.
.320 TYP.
.110
TYP.
MDU28C-xxB1 (Commercial J-Lead)
1
.300 TYP.
7 8
.200 MAX. (Com) .225 MAX. (Mil)
14
.510 MAX.
.065
TYP.
MDU28C-xxD1 (Commercial SMD) MDU28C-xxMD1 (Military SMD)
Doc #97040 DATA DELAY DEVICES, INC. 3
12/12/97 3 Mt. Prospect Ave. Clifton, NJ 07013
.360
TYP.
.065
TYP.
MDU28C-xxD4 (Commercial SMD) MDU28C-xxMD4 (Military SMD)
MDU28C
DELAY LINE AUTOMATED TESTING
O1
OUT
TRIGINREF
TRIG
PRINTER
I1O2I2
0.5V
0.5V
2.5V
2.5V
4.5V
4.5V
2.5V
2.5V
TEST CONDITIONS
INPUT: OUTPUT: Ambient Temperature: 25oC ± 3oC Load: 1 FAST-TTL Gate Supply Voltage (VDD): 5.0V ± 0.1V C Input Pulse: High = 5.0V ± 0.1V Threshold: 2.5V (Rising & Falling)
Low = 0.0V ± 0.1V
Source Impedance: 50 Max. Rise/Fall Time: 5.0 ns Max. (measured
between 0.5V and 4.5V )
Pulse Width: PWIN = 1.5 x Total Delay Period: PERIN = 10 x Total Delay
NOTE: The above conditions are for test only and do not in any way restrict the operation of the device.
COMPUTER
SYSTEM
: 5pf ± 10%
load
PULSE
GENERATOR
INPUT SIGNAL
OUTPUT SIGNAL
T
RISE
T
RISE
PW
V
IN
IH
DEVICE UNDER
TEST (DUT)
Test Setup
PER
IN
V
OH
T
FALL
T
FALL
TIME INTERVAL
COUNTER
V
IL
V
OL
Timing Diagram For Testing
Doc #97040 DATA DELAY DEVICES, INC. 4
12/12/97 Tel: 973-773-2299 Fax: 973-773-9672 http://www.datadelay.com
Loading...