DataComm 45-0014 User Manual
Instruction / Installation Sheet
DataComm Electronics Easy Mount Series
45-0014 Cable Plate with Flexible Opening, 1-Gang
DataComm Electronics, Inc.
6349 Peachtree Street
Norcross, GA 30071-1725
888.223.7977
770.662.8205
www.datacommelectronics.com
Parts Included Tools Needed
1. Cable Plate with Flexible Opening, 1-Gang 1. Drywall saw
Use the Cable Plate with Flexible Opening to install low voltage cables behind
your flat panel TV, (see Figures 2 & 3), your amplifier or other audio and video devices.
This wall plate is designed for use with Low Voltage / Data Cables “ONLY”.
The Cable Plate with Flexible Opening is designed with the low voltage mounting brackets molded to the back of the plate (see Figure 1).
Determine the location of your flat panel TV, amplifier or audio/video device. Use the enclosed template to cut a hole in the drywall. When cutting the
hole in the drywall, allow for the location of the stud. Now simply pull your audio/video cables through the wall and through the opening in the Cable Plate
with Flexible Opening. Now insert the Cable Plate with Flexible Opening flush into the wall. Next, screw down the wall plate screws with wings. The
wings will fasten tightly against the back of the drywall (see Figure 3) and your installation is complete.
This Cable Plate with Flexible Opening is Designed for Use with Low Voltage / Data Cables “ONLY”.
2. 6 Ft. tape measure
3. Pencil
4. Screwdriver
45-0014 – Front View
45-0014 – Back View
National Electrical Code (NEC) Does Not Allow the Installation of the TV Power Cord or an Extension Cord Behind the Wall.
Do Not Run or Pull the TV Cord or Other Electrical Cords Inside the Drywall.
CAUTION
Never install low voltage wiring during lightning storms.
Never install low voltage wiring in wet locations unless the wire is specifically designed for wet locations.
Never touch un-insulated low voltage wires or terminals unless the wire has been disconnected at its source.
Use caution when installing low voltage cables.
IMPORTANT INSTRUCTIONS
Read and understand all instructions.
Follow all warning and instructions marked on the product.
Do not use this product near water, for example near a bath tub, wash bowl, kitchen sink, or laundry tub, in a wet basement, or near a
swimming pool.
SAVE THESE INSTRUCTIONS.
2-1/4”
TEMPLATE
45-0014
Cable Plate with
Using
Template,
Cut a Hole
in the Drywall
Low Voltage
Mounting
Bracket Wing
Figure 1
Flat Screen TV
Surge Protector
Figure 2 - Front View
Concealed Low Voltage Wiring
(hidden in wall)
Receiver
4”
Flexible Opening
1-Gang
This product is patent protected
by U.S. Patent number 7495171
RoHS Compliant
Figure 3 - Back View
Flat Screen TV
ACTUAL SIZE
Concealed Low Voltage Wiring
(hidden in wall)
Receiver
Surge Protector
CUT ALONG DOTTED LINE
2/8/12
Instruction / Installation Sheet
DataComm Electronics Easy Mount Series
45-0015 Cable Plate with Flexible Opening, 2-Gang
DataComm Electronics, Inc.
6349 Peachtree Street
Norcross, GA 30071-1725
888.223.7977
770.662.8205
www.datacommelectronics.com
Parts Included Tools Needed
1. Cable Plate with Flexible Opening, 2-Gang 1. Drywall saw
3. Pencil
4. Screwdriver
Use the Cable Plate with Flexible Opening to install low voltage cables behind
your flat panel TV, (see Figures 2 & 3), your amplifier or other audio and video devices.
This wall plate is designed for use with Low Voltage / Data Cables “ONLY”.
The Cable Plate with Flexible Opening is designed with the low voltage mounting brackets
molded to the back of the plate (see Figure 1).
Determine the location of your flat panel TV, amplifier or audio/video device. Use the
enclosed template to cut a hole in the drywall. When cutting the hole in the drywall, allow
for the location of the stud. Now simply pull your audio/video cables through the wall and
through the opening in the Cable Plate with Flexible Opening. Now insert the Cable Plate
with Flexible Opening flush into the wall. Next, screw down the wall plate screws with
wings. The wings will fasten tightly against the back of the drywall (see Figure 3) and
your installation is complete.
erusaem epat .tF 6 .2
Figure 1
Using
Template,
Cut a Hole
in the Drywall
Low Voltage
Mounting
Bracket Wings
weiV kcaB – 5100-54 weiV tnorF – 5100-54
This Cable Plate with Flexible Opening is Designed for Use with
Low Voltage / Data Cables “ONLY”.
Do Not Run or Pull the TV Cord or Other Electrical Cords Inside the Drywall.
National Electrical Code (NEC) Does Not Allow the Installation of the TV Power Cord or an Extension Cord Behind the Wall.
CAUTION
Never install low voltage wiring during lightning storms.
Never install low voltage wiring in wet locations unless the wire is specifically designed for wet locations.
Never touch un-insulated low voltage wires or terminals unless the wire has been disconnected at its source.
Use caution when installing low voltage cables.
IMPORTANT INSTRUCTIONS
Read and understand all instructions.
Follow all warning and instructions marked on the product.
Do not use this product near water, for example near a bath
4-5/16”
tub, wash bowl, kitchen sink, or laundry tub, in a wet
basement or near a swimming pool.
SAVE THESE INSTRUCTIONS.
Figure 2 - Front View
Flat Screen TV
TEMPLATE
Concealed Low Voltage Wiring
Surge Protector
Receiver
(hidden in wall)
3-13/16”
Cable Plate with Flexible Opening
45-0015
2-Gang
Figure 3 - Back View
Concealed Low Voltage Wiring
(hidden in wall)
Receiver
Flat Screen TV
Surge Protector
ACTUAL SIZE
CUT ALONG DOTTED LINE
This product is patent protected by U.S. Patent number 7495171. RoHS Compliant.
3/7/12 Rev. 1
Loading...