DataComm 1 x 8 Coax 4 x 16 RJ45 Phone Module User Manual

DataComm Electronics, Inc.
6349 Peachtree Street

Norcross, GA 30071-1725

888.223.7977

770.662.8205
www.datacommelectronics.com

Instruction / Installation Sheet

DataComm Electronics Phone/Video Module 70-0025

1x8 Video Splitter and 4x16 RJ45 Phone Module

Step 1 Video

 Attach a female F-connector onto the cable TV service or satellite service

incoming cable.

 Screw the incoming cablewith F-connector to the connector marked

“input”.

 Using F-connectors, terminate all coaxial leads that have been pulled

through the top knockout of the enclosure to the 1 x 8video splitter.

 Align the four mounting pins with holes in the back of the panel (upper

most position recommended) and snap into place.

Step 2 Telephone

 Pull the telephone wires into the HCC panel from top or one of the side

knockouts.

 Using the black push pins, install the 70-0026 RJ45 telephone module in

the HCC panel. Install the cable from the telephone company
demarcation point to the 110 IDC marked from Telco. This will activate
line 1, line 2, line 3 and line 4 on the RJ45 ports.

 The wires should be punched down, using an industry standard punch-

down tool, to the 110 IDC connectors following the T568A wiring
configuration as shown below.

 Line 1 is Blue, Line 2 is Orange, Line 3 is Green and Line 4 is Brown.
 A RJ31X port is provided for line 1 seizure by security system.

White / Blue
Blue

White / Orange
Orange

White / Green

Green
White / Brown

Brown

INSTRUCTIONS ARE CONTINUED ON THE BACK SIDE OF THIS PAGE

4/1/08

DataComm Electronics Phone/Video Module 70-0025

ETL LISTED

1x8 Video Splitter and 4x16 RJ45 Phone Module

Step 3 Telephone

 Install RJ45 plugs (purchased separately – DCE part #20-5703) on all Cat

5e wiring home runs to the HCC panel.

 Be sure to wire the RJ45 plugs per the RJ45 plug instructions. Mis-wired

RJ45 plugs will create a short or no dial tone.

 Once all RJ45 plugs are installed on the home runs, determine which

telephone jacks in the house will be line 1. To connect line 1, insert the
RJ45 plug on the Cat 5e home run into RJ45 ports labeled line 1 on the

telephone module. Each of these home runs will now be connected to
line 1.

 To connect line 2, use same instruction as line 1 and use line 2 labeled

RJ45 ports.

 To connect line 3, use same instruction as line 1 and use line 3 labeled

RJ45 port.

 To connect line 4, use same instruction as line 1 and use line 4 labeled

RJ45 port.

Instruction / Installation Sheet

CAUTION

 Never install telephone wiring during lighting storms.
 Never install telephone jacks in wet locations unless the jack is

specifically designed for wet locations.

 Never touch un-insulated wires or terminals unless the telephone

line has been disconnected at the network interface.

 Use caution when installing or modifying telephone lines.

IMPORTANT INSTRUCTIONS

 Read and understand all instructions.
 Follow all warnings and instructions marked on the product.

 Do not use this product near water, for example a near bath tub,

wash bowl, kitchen sink, or laundry tub, in a wet basement, or near a
swimming pool.

 SAVE THESE INSTRUCTIONS.

ONLY LICENSED PROFESSIONALS SHOULD INSTALL THIS PRODUCT

CONFORMS TO

UL STD 1863

3026001

ANSI/UL STD 60950-1

CERTIFIED TO

CAN/CSA STD C22.2 NO 60950-1

4/1/08