DAS AUDIO VANTEC-20A, VANTEC-118A UM_VT3_02_EN.pdf

User's Manual

VANTEC-20A / VANTEC-118A

An te s d e u til iz ar el equ ip o, le a l a se cc ió n
“Precaucion es de seguridad” d e este manual.
Conserve este manual para futuras consultas.

Before operati ng the device, please read th e
“Safety precautions” section of this manual. Retain
this manual for future reference.

CONTENTS

SAFETY PRECAUTIONS

WARRANTY

DECLARATION OF CONFORMITY

INTRODUCTION

CONFIGURATIONS

2 x VANTEC-20A + 2 x VANTEC-218A

6 x VANTEC-20A + 2 x VANTEC-118A

6 x VANTEC-20A + 2 x VANTEC-218A

6 x VANTEC-20A + 4 x VANTEC-118A

LINE DRAWINGS

SPECIFICATIONS

AMPLIFIERS

Description

ON / OFF

Overload indicator

Equalisation

Overheating

Low mains voltage

3

4

5

6

7 - 10

11

11

12 - 18

Current consumption

Troubleshooting

RIGGING SYSTEM

ANNEX

Line connections: unbalanced and balanced

19 - 23

24

Manual del Usuario / vantec series / User’s Manual

Cajas acústicas activas / Self-powered loudspeaker enclosures
(VANTEC-20A, VANTEC-118A)

Precauciones de Seguridad
Safety Precautions

El signo de exclamación dentro de un triángulo indica la existencia
de importantes instrucciones de operación y mantenimiento en la
documentación que acompaña al producto.
Conserve y lea todas estas instrucciones. Siga las advertencias.
ATENCIÓN: Es un producto clase A , por lo que en entornos
domésticos puede causar radio-interferencias, en cuyo caso el
usuario tendrá que tomar las medidas oportunas.
De acuerdo con EN55103-2, usar el equipo sólo en entornos E1, E2, E3
ó E4.

No desconecte la tierra en el conector de alimentación pues es
peligroso e ilegal. Equipo de Clase I. El producto debe ser conectado
a un enchufe con toma de tierra. Sólo use este equipo con el cable
de red de alimentación adecuado para su país.
El signo del rayo con la punta de flecha, alerta contra la presencia de
voltajes peligrosos no aislados. Para reducir el riesgo de choque
eléctrico, no retire la cubierta.

No instale el aparato cerca de ninguna fuente de calor como
radiadores, estufas u otros aparatos que produzcan calor. Debe
instalarse siempre sin bloquear la libre circulación de aire por las
aletas del radiador.

No exponga este equipo a la lluvia o humedad. No use este aparato
cerca del agua (piscinas y fuentes, por ejemplo). No exponga el
equipo a salpicaduras ni coloque sobre él objetos que contengan
líquidos, tales como vasos y botellas. Equipo IP-20.

Este símbolo indica que el presente producto no puede ser tratado
como residuo doméstico normal, sino que debe entregarse en el
corre spondiente punto de reco gida de e quipos el éctricos y
electrónicos.
Equipo diseñado para funcion ar entre 1 5ºC y 45ºC con una
humedad relativa máxima del 95%, con un rango de ±10% de la
tensión nominal de alimentación indicada en la etiqueta trasera
(según IEC 60065). Si debe sustituir el fusible preste atención al tipo
y rango.

El cableado exterior conectado al equipo requiere de su instalación
por una persona instruida o el uso de cables flexibles ya preparados.

The exclamation point inside an equilateral triangle is intended to
alert the users to the presence of impo rtant operating and
ma in tena nc e (s er vi cin g) in stru ct ions in th e l ite ra ture
acc ompanyi ng the prod uct. Heed all wa rnings. Follo w a ll
instructions. Keep these instructions.
WARNING: This is a class A product. In a domestic environment this
product may cause radio interferences in which case the user may
be required to take adequate measures.
Use this product only in E1, E2, E3 or E4 environments according to
EN55103-2.

Do not remove mains connector ground, it is dangerous and illegal.
Class I device. The product must be connected to a mains socket
outlet with protective earth connection. Only use this equipment
with an appropriate mains cord for your country.

The lightning and arrowhead symbol warns about the presence of
uninsulated dangerous voltage. To reduce the risk of electric shock,
do not remove the cover.

Do not install near any heat sources such as radiators, heat registers,
stoves or other apparatus that produce heat. The circulation of air
through the heatsink must not be blocked.

Do not expose this device to rain or moisture. Do not use this
apparatus near water (for example, swimming pools and fountains).
Do not place any objects containing liquids, such as bottles or
glasses, on the top of the unit. Do not splash liquids on the unit. IP­20 equipment.

This symbol on the product indicates that this product should not
be treated as household waste. Instead it shall be handed over to
the appicable collection point for the recycling of electrical and
electronic equipment.
Working temperature ranges from 15ºC to 45ºC with a relative
humidity of 95%, with ±10% of the rated main voltage value
indicated on the rear label (according to IEC 60065). If the fuse
needs to be replaced, please pay attention to correct type and
ratings.

The outer wiring connected to the device requires installation by an
instructed person or the use of a flexible cable already prepared.

Si el aparato es conectado permanentemente, la instalación
eléctrica del edificio debe incorporar un interruptor multipolar con
separación de contacto de al menos 3mm en cada polo.

Para desconectar el dispositivo debe usar el enchufe. Desconecte
este aparato durante tormentas eléctricas, terremotos o cuando no
se vaya a emplear durante largos periodos.

No emplace altavoces en proximidad a equipos sensibles a campos
magnéticos, tales como monitore s de televisión o ma terial
magnético de almacenamiento de datos.

Para las cajas con vaso para trípode, la altura máxima de seguridad
desde el suelo a la base de la caja montada sobre trípode modelo
TRD-2, con pies a 55 cm del eje del trípode, es:

VANTEC-20A ------------->150 cm

El colgado del equipo sólo debe realizarse utilizando los herrajes de
colgado recomendados y por personal cualificado. No cuelgue la
caja de las asas.

No existen partes ajustables por el usuario en el interior de este
equipo. Cualquier operación de mantenimiento o reparación debe
ser realizada por personal cualif icado. Es necesario el servicio
técnico cuando el equipo se haya dañado de alguna forma, como
que haya caído líquido o algún objeto en el interior del aparato, haya
sido expuesto a lluvia o humedad, no funcione correctamente, haya
recibido un golpe o su cable de red esté dañado.

Limpie con un paño seco. No use limpiadores con disolventes. Clean only with a dry cloth. Do not use any solvent based cleaners.

55 cm

If the apparatus is connected permanently, the electrical system of
the building must incorporate a multipolar switch with a separation
of contact of at least 3mm in each pole.

To disconnect the device, you should use the mains plug. Unplug
this apparatus during lightning storms, earthquakes or when
unused for long periods of time.

Do not place loudspeakers in proximity to devices sensitive to
magnetic f ields such as television monitors or data storage
magnetic material.

For enclosures with tripod socket, the maximum safety height from
floor to bottom of enclosure when mounting on a TRD-2 tripod,
with legs spread 55cm from the central pole, is:

VANTEC-20A ------------->150 cm

The appliance should be flown only from the rigging points and by
qualified personnel. Do not suspend the box from the handles.

No user serviceable parts inside. Refer all servicing to qualified
service personnel. Servicing is required when the apparatus has
been damaged in any way, such as power-supply cord or plug is
damaged, liquid has been spilled or objects have fallen into the
apparatus, the apparatus has been exposed to rain or moisture,
does not operate normally or has been dropped.

Manual del Usuario / vantec series / User’s Manual

3

GARANTÍA

Todos nuestros productos están garantizados por un periodo de 24
meses desde la fecha de compra.

Las garantías sólo serán válidas si son por un defecto de fabricación y
en ningún caso por un uso incorrecto del producto.

Las reparaciones en garantía pueden ser realizadas, exclusivamente,
por el fabricante o el servicio de asistencia técnica autorizado.

Otros cargos como portes y seguros, son a cargo del comprador en
todos los casos.

Para solicitar reparación en garantía es imprescindible que el
producto no haya sido previamente manipulado e incluir una fotocopia
de la factura de compra.

WARRANTY

All our products are warrantied against any manufacturing defect for
a period of 2 years from date of purchase.

The warranty excludes damage from incorrect use of the product.

All warranty repairs must be exclusively undertaken by the factory or
any of its authorised service centers.

To claim a warranty repair, do not open or intend to repair the product.

Return the damaged unit, at shippers risk and freight prepaid, to the
nearest service center with a copy of the purchase invoice.

4

Manual del Usuario / vantec series / User’s Manual

DECLARACIÓN DE CONFORMIDAD

DECLARATION OF CONFORMITY

DAS Audio Group, S.L.
C/ Islas Baleares, 24 - 46988 - Pol. Fuente del Jarro - Valencia. España (Spain).

Nota: Los textos completos de la declaración de conformidad para VANTEC-
12A, VANTEC-15A, VANTEC-20A y VANTEC-215A están disponibles en
http://d.dasaudio.com/vK2D4.

Note: The full text of the declaration of conformity for VANTEC-12A, VANTEC-15A,
VANTEC-20A and VANTEC-215A is available at http://d.dasaudio.com/vK2D4.

Declara que VANTEC-118A:
Declares that VANTEC-118A:

Cumple con los objetivos esenciales de las Directivas:
Abide by essential objectives relating Directives:

l Directiva de Baja Tensión (Low Voltage Directive) 2014/35/UE

l Directiva de Compatibilidad Electromagnética (EMC)

2014/30/UE

l Directiva RoHS 2011/65/UE

l Directiva RAEE (WEEE) 2012/19/UE

Y es conforme a las siguientes Normas Armonizadas Europeas:
In accordance with Harmonized European Norms:

l EN 60065:2014.- Audio, video and similar electronic apparatus. Safety

requirements.

l EN 55032:2012.- Electromagnetic compatibility of multimedia

equipment. Emission requirements.

l EN 55103-2:2009.- Electromagnetic compatibility. Product family

standard for audio, video, audio-visual and entertainment lighting
control apparatus for professional use. Part 2:Immunity.

l EN 50581:2012.- Technical documentation for the assessment of

electrical and electronic products with respect to the restriction of
hazardous substances.

Manual del Usuario / vantec series / User’s Manual

5

INTRODUCTION

The VANTEC-20A and VANTEC-118A, powered multifunction systems combine DAS´s reputation for performance
and reliability with the latest technological innovations offering users an unmatched level of versatility. The
exceptional characteristics of the onboard amplification, complex waveguide design and digital signal processing
provide the output and control required, allowing the vantec series to be deployed as a main system or in any
number of support applications. The easy-to-use rigging hardware and range of mounting accessories expand the
possible applications of the vantec series.

Features

VANTEC-20A

– Active Curved Source Line Array
– Class D Bi-amplified 1500 Wpeak
– FIR filters for linear phase response
– 1 x DAS 12F4C + 2 x M-60 compression drivers
– Compact design with high output capabilities
– DAScontrol™ with presets and configurations
– DASlink™ wireless streaming and remote control
– +/- 13.5º variable tilt pole mount

The VANTEC-20A is an active curved source line array that incorporates an arsenal of hi-tech solutions designed to
provide the versatility needed by today’s sound hire professionals. Whether it be stacked on the VANTEC-118A
companion subwoofer, flown in a compact array, or used alone on a speaker stand, the VANTEC-20A can be used
effectively in an incredible number of applications that include corporate A/V, mid-size sound reinforcement, and
permanent installation.

Designed for use in arrays of up to 5 units, the VANTEC-20A is ideal for applications where the power and long-throw
characteristics of large line arrays are not needed. Individual units can be mounted on tripods with precise aiming
possible thanks to the variable angle pole mount which allows for 13.5º up or down tilt.

The DAScontrol™ interface allows users to easily configure the VANTEC-20A systems for use individually or in
combination with other units. Selectable high pass filter presets facilitate alignment with the VANTEC-18A and VANTEC-
118A active bass systems without external processing. Throw compensation settings and array size selection can all
be handled simply via the DAScontrol™ interface. When the VANTEC-20A is used individually, the DASlink™ APP can be
used to stream music in high definition stereo and remotely control the systems functions.

The enclosure is manufactured using Baltic birch plywood and finished with the DAS ISO-flex coating. Power is
supplied by a cutting-edge 1500 Wpeak Class D amplifier in a biamplified conf iguration driving a single DAS 12F4C
loudspeaker and twin M-60 compression drivers.

VANTEC-118A

– Active front-loaded subwoofer system
– 1 x 18″ DAS 18FW loudspeaker
– Class D amplifier 2000 Wpeak
– Digital signal processing (DSP)
– Unique “Deep-Loud” bass EQ switch
– Variable low-pass f ilter 80 Hz-125 Hz
– LED ON/OFF switch on backplate
– Top located pole mount socket

The VANTEC-118A is an active front loaded bass system
which has been designed specif ically for use with the VANTEC-
20A curved source line array. Compact in size, the unit can be
flown in arrays or linked together in ground stacks thanks to
the rigging system which is compatible with the VANTEC-20A.

The electronics package includes a 2000 Wpeak Class D amplifier and 24-bit high-end DSP for exceptional
audio reproduction. A unique “Deep-Loud” EQ switch allows users to tailor the bass output to provide a low
subwoofer type response using the “Deep” setting or a louder hard hitting performance in the “Loud” setting. On
the rear panel, controls can be found for gain, polarity and a continually variable low-pass f ilter which ranges
from 80 Hz to 125 Hz. The VANTEC-118A is phase response coherent with the other Vantec series active tops such as
the VANTEC-20A offering precise alignment without the need of an external DSP.

6

Manual del Usuario / vantec series / User’s Manual

CONFIGURATIONS

2 x VANTEC-20A

2 x VANTEC-218A

POWER

POWER

POWER

POWER

Speaker cabling

SC-2 2m XLR microphone signal balanced cable

Accessories

Manual del Usuario / vantec series / User’s Manual

Units

2

2TRD-6 Ring lock pole mount for use between satellite and sub system, black

7

CONFIGURATIONS (cont’d)

6 x VANTEC-20A

2 x VANTEC-218A

DSP-2060A

POWER

POWER

Processors

Speaker cabling

POWER

POWER

Units

1DSP-2060A 2 In/6 Out fully configurable DSP, 9 full bandwidth parametric band EQ on each channel, AudioCore/DASnet equipped

SC-1 1m XLR microphone signal balanced cable

PWCONLINK-09 0.9m powerCON “jumper” NAC3FCB cable

Accessories

Manual del Usuario / vantec series / User’s Manual

4

4

2AX-VT20 Rigging bumper for VANTEC-20A (max 5 u.), black
2PL-VT20S

9

CONFIGURATIONS (cont’d)

6 x VANTEC-20A

4 x VANTEC-118A

DSP-2060A

POWER

POWER

Processors

Speaker cabling

POWER

POWER

Units

1DSP-2060A 2 In/6 Out fully configurable DSP, 9 full bandwidth parametric band EQ on each channel, AudioCore/DASnet equipped

SC-1 1m XLR microphone signal balanced cable

PWCONLINK-09 0.9m powerCON “jumper” NAC3FCB cable

Accessories

10

6

6

2AX-VT20 Rigging bumper for VANTEC-20A (max 5 u.), black
2PL-VT20S
2PL-VT118S

Manual del Usuario / vantec series / User’s Manual

LINE DRAWINGS

ALL DIMENSIONS IN MILLIMETERS

620

VANTEC-20A

VANTEC-118A

Front View

610

Front View

SPECIFICATIONS

Nominal Amplifier Power

Input Impedance

Frequency Range (-10dB)

Horizontal Coverage (-6dB)

Vertical Coverage

Maximum Peak SPL at 1m

Transducer/Replacement Parts

Enclosure Geometry

Enclosure Material

Rigging System

AC Power Requirements

Dimensions (H x W x D)

330

MODEL

Input Type

Sensitivity

Color/Finish

Connectors

Weight

Accessories

435

Right View

485

Left View

Bottom View

780

Top View

VANTEC-20A VANTEC-118A

1500 Wpeak (Class D Bi-amp)
Balanced Differential Line
Line: 20kOhms
Line: 3 V (+12dBu)
63 Hz - 20 kHz
90º Nominal
15º Nominal
135 dB
LF: 1 x 12F4C/GM-12F4
HF: 2 x M-60/GM-M60N
Trapezoidal 7.5º
Birch Plywood
Black / ISO-flex Paint
Integrated in box design
INPUT: 1 x Female XLR
LOOP THRU: 1 x Male XLR
AC INPUT: 1 x PowerCon
AC OUTPUT: 1 x PowerCon

3.0A, 115V, 50 Hz/60 Hz

1.5A, 230V, 50 Hz/60 Hz
330 x 620 x 435 mm
13 x 24.4 x 17.1 in

28.6 kg (62.9 lb)
ANL-2
AX-VT20
TRD-2
TRD-6
PL-VT20S
FUN-3-VT20

2000 Wpeak
Balanced Differential Line
Line: 20kOhms
Line: 3 V (+12dBu)
35 Hz - 125 Hz

-

­134 dB
LF: 1 x 18FW/GM-18FW

­Rectangular
Birch Plywood
Black / ISO-flex Paint
Integrated in box design
INPUT: 2 x Female XLR
LOOP THRU: 2 x Male XLR
AC INPUT: 1 x PowerCon
AC OUTPUT: 1 x PowerCon

4.4A, 115V, 50 Hz/60 Hz

2.2A, 230V, 50 Hz/60 Hz
485 x 610 x 780 mm

19.1 x 24 x 30.7 in

45.2 kg (99.4 lb)
ANL-2
AX-VT20
TRD-6
PL-VT118S
FUN-2-VT118

Rear View

Rear View

DAS Audio Group, S.L. continuously strives to enhance its products through investigation and development. All
specifications are subject to change without prior notice.

Manual del Usuario / vantec series / User’s Manual

11

AMPLIFIERS

Description: VANTEC-118A

1) INPUT connectors :
1/4” Jack+XLR combined socket-type input signal connectors. This is a balanced connector just like the LOOP THRU

connector with the following pin assignments:

1 or S =GND (ground).
2 or T =(+) Non inverted input.
3 or R =(-) Inverted input.

2) SATELLITE OUTPUT
A and B, XLR-type output signal connectors for connecting several units together and sending them all the same input
signal or filtered signal (by using THRU/HPF).

3) LIMIT:
Red LED indicates amplif ier saturation. Amplif ier limiter indicator lights.

4) SIGNAL:
Green LED indicates signal presence.

5) ON:
Green LED indicates that the unit is ON.

6) SUB LEVEL:
Potentiometer for adjusting the unit level.

7) AC INPUT :
Standard PowerCon NAC3FCA mains connector (inserted,
rotated and locked for ON). Only use this equipment with an
appropriate mains cord.

8) THRU/HPF :
‘SATELLITE OUTPUT’ selector to switch between full range
signal or pass filter with cut-off f requency of 100 Hz.

9) LOW-PASS CROSSOVER :
Button for adjusting the upper cut-off frequency for the
subwoofer unit. We recommend a cut-off f requency of 100 Hz
for vantec series use.

10) PHASE :
Switch for inverting the phase of the unit.

11) PRESET DEEP/LOUD
Button for switching between two types of f requency
response, DEEP or LOUD.

12) AC OUTPUT:
PowerCon NAC3FCB connector for AC loop thru allows up
to 6 units when using a 230V version (see unit’s label)). Only
use this equipment with an appropriate mains cord.

DAS Audio Group, S.L. (Valencia)

MADE IN SPAIN

LEVEL

0

6

www.dasaudio.com

10

OUTPUT A OUTPUT B

LED

OFF/ON

INPUT A

AC INPUT

115/230 V~ 50/60Hz 500W

7

VANTE C

series

Model: VANTEC-118A

LOW-PASS

100Hz

+6-oo

80Hz

125Hz

POLARITY

- +

SATELLITE X-OVER

PRESET

DEEP/LOUD

HPF/THRU

INPUT B

AC OUTPUT

MAX. 6@230V / 2@115V

UNITS VANTEC-118A

LIMIT

9

SIGNAL

ON

3

4

5

11

2

8

DO NOT OPEN

CAUTION

TO RAIN OR MOISTURE

RISK OF ELECTRIC SHOCK

1

DO NOT EXPOSE THIS EQUIPMENT

12

12

Manual del Usuario / vantec series / User’s Manual

Description: VANTEC-20A

Note: The INPUT and LOOP THRU are type XLR balanced connectors.

By default the state of the parameters shown is the following.
Keep in mind that any parameter changed in the DSP will
remain with the same value until someone changes it again.

AUDIO MANAGEMENT

+ 0dB

1U

HPF: off

THROW: Mid

1

O

Press the encoder to start navigation

"N.ofU" (NUMBER OF UNITS)

The DAS array correction named Number Of Units is a
parameter that compensates the amount of energy in the
low-mid frequency range in the array:

AUDIO MANAGEMENT

MAIN MENU

BACK

No.ofU: 1U

ADJUSTING THE LEVELS

Once the input source has been connected to the amplifer´s
cabinet, the user has to check the gain structure of the
system.
Adjust level output f rom your processor and/or mixing
console in order to prevent INPUT CLIP (left signal meter):

Exceeding the limits may
cause damage in the system

As well, try to avoid excessive volume at the amplif ier´s
output (right signal meter). Be sure that your gain structure is
adequate and not causing amplifier LIMIT:

AUDIO MANAGEMENT

C

1U

INPUT

CLIP

HPF: off

THROW: Mid

1

AUDIO MANAGEMENT

LIMIT

1U

HPF: off

HPF: off

By pressing the encoder (DAScontrol) the user can have
access to the menu:

Rotate the encoder to the desired choice, in this case “No.ofU”
and press to access all the options:

AUDIO MANAGEMENT

MAIN MENU

BACK

No.ofU: 1U>

O

The available options for “No.ofU” are: 1, 2, 3, 4, 5 depending on
the size of the array. Rotate the encoder to select the option
needed and press again to confirm.

L

HPF: off

THROW: Mid

1

O

Exceeding the limits may
cause damage in the system

Manual del Usuario / vantec series / User’s Manual

Use the same “Number Of Units” IN ALL the cabinets of your
system!

13

HPF (High Pass Filter)

By pressing the enconder (DAScontrol) the user can have
access to the menu; rotate to navigate until selecting HPF:

AUDIO MANAGEMENT

MAIN MENU

BACK

No.ofU: 1U

HPF: off

Press the encoder:

AUDIO MANAGEMENT

MAIN MENU

BACK

No.ofU: 1U

HPF: off

Rotate the encoder and press to confirm one of the
following” HPF” options: off, 63Hz,V118A, 100Hz.

User MUST enable the SAME HPF in ALL cabinets forming
the array!

In order to have more dynamic headroom in the system,
when used with subs, HPF at V118A position (with Vantec
subwoofers) or 100Hz is highly recommended.

THROW

Press the encoder and rotate it until “THROW” is shown in
the display:

AUDIO MANAGEMENT

MAIN MENU

No.ofU: 1U

HPF: off

THROW: Mid

Press the encoder to enter into this f ield.There are 5 options
available,” Long, L-Mid, Mid, Mid-S, Short”.

14

Manual del Usuario / vantec series / User’s Manual

WIRELESS CONNECTIVITY

Master cabinet

MAIN MENU

WIRELESS AUDIO

OPTIONS

WIRELESS AUDIO

STATUS: not linked

CREATE A NEW LINK

BACK

BACK

The VANTEC series systems include wireless connectivity for streaming audio
and / or system´s management. By the use of the f ree APP DASlink users can
send audio up to 2 devices (Master + Slave) and control / monitor them changing
parameters and creating custom presets. First Step is going to the WIRELESS
Audio Sub-menu in the master cabinet:

Only Wireless Audio Wireless Audio + Control (DASL ink)

AUDIO

SINGLE Mode Master & Slave

Master cabinet

CREATE NEW LINK

Select Mode:

SINGLE: L+R > < MASTER: L >

Master cabinet

CREATE NEW LINK

Connect from your

device to:

VANTEC-20A-089E39

option in your smart phone
or tablet and select the
VANTEC cabinet.

Phone / tablet

CREATE NEW LINK

Select Mode:

CREATE NEW LINK

in SLAVE: R mode

CONTINUE

When selecting Master L

the Slave cabinet. Press
Continue and go to the other
cabinet and it in
Slave R mode:

CREATE NEW LINK

Select Mode:

< SLAVE: R >

Master cabinet

Master cabinet

Slave cabinet

AUDIO and CONTROL DASlink

Master cabinet

CREATE NEW LINK

Select Mode:

< DASlink >

Master cabinet

CREATE NEW LINK

Connect from your

device to:

VANTEC-20A-089E39

Phone / tablet

Phone / tablet

Adding Slave Unit

Slave cabinet

CREATE NEW LINK

Select Mode:

< SLAVE: R >

Slave cabinet

CREATE NEW LINK

Waiting MASTER

connection

---- Wait a minute ----

Phone / tablet

Master cabinet

CREATE NEW LINK

LINK DONE!!

Slave cabinet

CREATE NEW LINK

Waiting MASTER

connection

---- Wait a minute ----

tablet, smart phone etc.

Master cabinet

CREATE NEW LINK

Select Mode:

< MASTER: L >

Master cabinet

CREATE NEW LINK

Connect from your

device to:

VANTEC-20A-089E39

Master & Slave cabinet

CREATE NEW LINK

LINK DONE!!

Master cabinet

CREATE NEW LINK

Searching for SLAVE

Altea unit

---- Wait a minute ----

Master & Slave cabinet

CREATE NEW LINK

LINK DONE!!

Manual del Usuario / vantec series / User’s Manual

15

OPTIONS

In this sub-menu the user can configure all the non-audio
related options. Remember that in order to access each
parameter it is necessary to push the encoder:

OPTIONS MENU

BACK

BRIGHT: 0

CONTRAST: 0

OPTIONS MENU OPTIONS MENU OPTIONS MENU

BACK BACK BACK

BRIGHT: 0 BRIGHT: 0 BRIGHT: 0

CONTRAST: 0

OPTIONS MENU

DIMMING: on

LOGO: on

MENU LOCK: off

DIMMING: When active the screen lowers its luminosity after a few seconds

OPTIONS MENU

DIMMING: on

LOGO: on

MENU LOCK: off

OPTIONS MENU

DIMMING: on

LOGO: on

MENU LOCK: off

A. User can LOCK the Display and Master Volume Control by enabling this option MENU LOCK: ON

B. User can LOCK the Display and the encoder WITH PASSWORD by enabling this option MENU LOCK: pw292

In case A to unlock just press the encoder: In case B to unlock PUSH encoder and enter the 3 digit password: 292

OPTIONS MENU OPTIONS MENU

BACK BACK

BRIGHT: 0 BRIGHT: +10

CONTRAST: 0 CONTRAST: 0

CONTRAST: -10 CONTRAST: +10

OPTIONS MENU

DIMMING: <on

LOGO: on

MENU LOCK: off

OPTIONS MENU

DIMMING: on

LOGO: <on>

MENU LOCK: off

OPTIONS MENU

DIMMING: on

LOGO: on LOGO: on LOGO: on

MENU LOCK: off>

OPTIONS MENU

DIMMING: off>

LOGO: on

MENU LOCK: off

OPTIONS MENU OPTIONS MENU

DIMMING: on DIMMING: on

LOGO: off > LOGO: <limit

MENU LOCK: off MENU LOCK: off

OPTIONS MENU OPTIONS MENU

DIMMING: on DIMMING: on

MENU LOCK: <on> MENU LOCK:<pw292

LOCKED

PUSH TO UNLOCK

+ 0dB + 0dB + 0dB

1U 1U 1U

HPF: off HPF: off HPF: off

THROW: Mid THROW: Mid THROW: Mid

1 1 1

OPTIONS MENU

STAND-BY: off

RESET DEVICE

INFORMATION

STAND-BY:When no signal is detected the amplifer shuts down. Time can be selected

OPTIONS MENU

STAND-BY: off

RESET DEVICE

INFORMATION

OPTIONS MENU

RESET DEVICE

INFORMATION

BACK

O O O

FW 3.12 DSP10 uC35

UNLOCKED Password: 0 0 0

OPTIONS MENU OPTIONS MENU

STAND-BY: off> STAND-BY:<5min>

RESET DEVICE RESET DEVICE

INFORMATION INFORMATION

RESET DEVICE

Are you sure?

NO YES

VANTEC20A

Melody V6.1.4

This option resets the device to the following values:

No.ofU: 1U
HPF: off

THROW: Mid
STAND-BY: off
DIMMING: on
LOGO: on
MENU LOCK: off

16

Manual del Usuario / vantec series / User’s Manual

ON / OFF

A sou nd sys te m sh ould be s witc hed on
sequentially. Switch on the self-powered units last
in your sound system (switch on the subwoofer
before the mid-high system). Switch on the sound
sources such as CD players or turntables, then the
mixer, then the processors, and f inally the self­powered unit. If you have several units, it is
recomm e n d e d t h at y o u sw i t c h t he m o n
sequentially one at a time.
Follow the inverse order when switching off,
turning self-powered units off before any other
element in the sound system.

Disconnect the device by removing the mains
connector f rom the mains socket. The mains
connector and mains socket must always be f reely
accessible and never covered or blocked in any
way. The mains cable can be detached from the
device by disconnecting the standard PowerCon
NC3FCA connector. Always disconnect the device
by removing the mains connector from the mains
socket before detaching the mains cable at the
PowerCon NC3FCA connector.
Power can be daisy chained via the NC3FCB
output connector (see details on product label).

IMPORTANT: Do not disconnect the unit while
in use.
Ensure that the device is disconnected from
the mains by observing that the ON LED is turned
off. Please note that the ON LED can stay on for
several seconds after the mains power has been
disconnected.

Overheating

This equipment does not normally overheat
du r i n g no rm a l c on d it i o ns o f u se . Wh en
overheating occurs, the unit protects itself. You
should then find out why and if necessary contact
an authorised dealer for technical assistance.

Normally it is enough just to let the unit cool
down after you have corrected the problem so that
the system functions properly again.

Low mains voltage

If mains voltage falls below the shutdown
voltage for the unit, it will stop playing. When
acceptable levels are regained, the unit will switch
back on automatically.

Therefore the current consumed by a 115V
version is double the 230V version to achieve the
same acoustic power level.

Pink Noise

Mains 230 Vrms

VANTEC-20A

VANTEC-118A

1/3 Power

1.5A

2.2A

Overload LED indicator (VANTEC-118A)

This device has an indicator (LIMIT LED) that
lights when the signal is excessive.
The indicator should not be lit continuously.
This distorts the signal (quickly fatiguing your ears)
and may damage the speakers. Therefore, it is
recommended that you never work with this LED
on; at most it should blink only occasionally.

Overload Screen indicators ( 20A)VANTEC-

In the main screen when input signal levels are
too high on the left side the meters will display
“input clip”.
If the input levels are in between the limits but
the output level gain is too much the right meter
will display “limit”.

Equalisation

The unit does not need extreme settings of
equalisation to produce quality sound. Avoid high
levels of gain on the equalisers. Gain values above
+3 dB on a console’s EQ are not recommended.

Manual del Usuario / vantec series / User’s Manual

17

Troubleshooting

No sound f rom the unit. The input
meters in the screen do not show any
signal presence.

Full power cannot be obtained.
LIMIT message never appears in the
screen.

Sound i s d i s torted. INPUT CL IP
message is shown.

Sound is distorted. LIMIT message is
displayed.

H u m o r b u zz w he n a m i xe r i s
connected to the unit.

1 - The signal source is sending no signal.
2 - Input gain controls are at minimum
position.
3 - Defective cable.
4 - If Wireless Audio is connected input 1
which controls audio is at mimimum
position or Volume of the source is
muted.

1 - The signal source does not have
enough ouput level.
2 - Input gain controls are at very low
volume.
3 - Master Volume is very low.

1-The m i x e r o r s ig na l s ou rc e is
distorting.
2 - The output level from the mixer is too
high.
3 - Input gain controls are set too high.

The syste m i s overloa ded and ha s
reached maximum power.

1-The console probably has unbalanced
outputs. You may be using an incorrect
unbalanced to balanced cable.
2 - The mixer and the powered speaker
are not plugged into the same mains
outlet.
3 - The audio signal cable is too long or
too close to an AC cable.

1 - Check that the source is not muted
and is sending signal to the unit.
2 - Check input gain controls. Put them
at 0dB.
3 - Check that the cable from the source
to the un it is co nnected corre ct ly.
Replace the cable if defective.
4 - Adjust Volume of input gain control
number one.

1 - Use balanced outputs of a mixer.
Rise master oup ut volume o f the
source.
2 - Set up input gain controls at higher
positions.
3 - Increase Volume by turning up the
Master Volume control.

1-Turn down the mixer´s output and
check no channels are distroting.
2 -Turn down the mixer´s output.
3 - Turn down input gain controls.

1 - Turn down the mixer´s output.
2 - Tu rn down th e ma ster ou tput
volume in the unit.

1-Read the appendix of this manual to
make a correct unbalanced to balanced
cable.
2 - Connect the mixer and the unit to
the same mains outlet.
3 - Use a cable that is as short as possible
and/or move the audio signal cable
away from mains cables.

Hum or bu zz when us ing lighting
controls in the same building.

The screen does not light up when the
mains connector is connected and the
power switch ON.

1-The audio signal cable is too long or
too close to the lighting cable.
2 - On a sound system with three phase
AC, the lighting equipment and the
unit are connected to the same phase.

1 - Bad or loose AC connection to the
unit or the mains outlet.
2 - Faulty AC cable.
3 - Blown Fuse.
4 - The mains voltage is out of range.
5 - Damaged amplif ier.

1- Move the audio signal cable away
from lighting cables.Try to find out at
what point the noise is leaking into the
system.
2 - Connect the sound system to a
different phase than the lights. You may
need the help of an electrician.

1 - Check your connections.
2 - Check the cables, connectors and AC
power with a suitable mains tester.
3 - Replace the blown fuse with another
of the same type and size.
4 - If the multimeter determines that
the mains voltage is out of the range
you may need the assistance of an
elec tr ic ia n to f ind an appropriate
solution.
5 - Contact a qualified tech service
center.

18

Manual del Usuario / vantec series / User’s Manual

RIGGING

Warning

To perform any operations related to flying the
system, read the present document first, and act
on the warnings and advice given. The goal is to
allow the user to become familiar with the
mechanical elements required to fly the acoustic
system, as well as the safety measures to be taken
during set-up and teardown.

Only experienced installers with adequate
knowledge of the equipment and local safety
regulations should fly speaker boxes. It is the user's
responsibility to ensure that the systems to be
flown (including flying accessories) comply with
state and local regulations.

The working load limits in this manual are the
results of tests by independent laboratories. It is
the user's responsibility to stay within safe limits. It
is the user's responsibility to follow and comply
with safety factors, resistance values, periodical
supervisions and warnings given in this manual.
Product improvement by means of research and
development is on going at DAS. Specifications are
subject to change without notice.

It is common practice to apply 5:1 safety factors
for enclosures and static elements. For slings and
elements exposed to material fatigue due to
friction and load variation the following ratios
must be met; 5:1 for steel cable slings, 4:1 for steel
chain slings and 7:1 polyester slings. Thus, an
element with a breaking load limit of 1000 kg may
be statically loaded with 200 kg (5:1 safety factor)
and dynamically loaded with 142 kg (7:1 safety
factor).

Absolutely no risks should be taken with
regards to public safety. When flying enclosures
from ceiling support structures, extreme care
should be taken to assure the load bearing
capabilitie s of the structures so that the
installation is absolutely safe. Do not fly enclosures
from unsafe structures. Consult a certified
professional if needed. All flying accessories that
are not supplied by DAS Audio are the user's
responsibility. Use at your own risk.

The DAS VANTEC-20A incorporates structures in
each side of the enclosure. Thess ironworks are
made of steel and aluminum and are fixed with
special screws in the wood side of the two systems.
On each one of these structures there is a steel rod
with a special axis screw which allows to stack or
rig the enclosures. The angles vary from 15º to 15º
with each VANTEC-20A. This system allows for easy
and safe rigging or stacking, with safety pins.

Flyable vantec series models feature internal
steel angles, so that flying points are available.
Eyebolt flying points are factory sealed with M10
screws, which are replaced with eyebolts on the
flying points as required. Flying with eyebolts is
very economical and safe, and is specially
recommended for installations where the boxes
are permanently fixed.

When flying a system, the working load must
be lower than the resistance of each individual
flying point in the enclosure, as well as each box.
Hanging hardware should be regularly inspected
and suspect units replaced if in doubt. This is
important to avoid injury and absolutely no risks
should be taken in this respect. It is highly
recommended that you implement an inspection
and maintenance program on flying elements,
including reports to be filled out by the personnel
that will carry out the in spections. Lo ca l
regulations may exist that, in case of accident, may
require you to present evidence of inspection
reports and corrective actions after defects were
found.

Manual del Usuario / vantec series / User’s Manual

19

Safety pin (Ø 6 mm) that
allows to hook the enclosures

Please follow the process to attach one box to
another. First, let's look at the sides of the
enclosure that we can see in the figure.

In the figure we can see the safety pin and the
lower trigger. The safety pin is housed in a holder
and the sliding attachment plate is hidden. By
placing the pin in the indicated hole, the enclosure
can be joined with the box directly above by
passing the pin through the orifice in the sliding
attachment plate of the upper box.

This rigging system is compatible with the

VANTEC-118A, making suspension from the VANTEC­118A easy.

Moving the lower trigger up (1), releases the sliding attachment plate that will fall by its own weight (2).
When the trigger is released, it will return to its original position and the slide will remain f ixed (3).

The lower trigger releases
and allows to retract the attachment plates.

1

1

3

42

Similarly, to retract the slide we must act on the trigger as in (1) push the slide up (4), and release the
trigger (3).

To attach enclosures, place a VANTEC-20A enclosure with the attachment plates extended upon another
VANTEC-20A. Next, insert the safety pins in the hole and through the orifice of the attachment plates so that the
boxes are joined. The angle between both enclosures will be 15º.

Attention: Make sure the correct insertion of the safety pin.

15º

20

Manual del Usuario / vantec series / User’s Manual

To unhook the enclosures we will act on the upper pins of the lower box as indicated below:

1

First we remove the pins (1) on each side. Now, we reposition the pins in the holders (2). We can now
separate the enclosures (3). Finally, we retract the attachment plates as indicated on the previous page.

AX-VT20

The rigging frame AX-VT20 is suitable for hanging a
maximum of 5 units of VANTEC-20A. It has 11 pick-up points
for the lifting slings, numbered from front to back (see
attached figure). To assure the vertical inclination of the
entire column use the Ease Focus software, which will
indicate which holes have to be used. This frame will be
joined to the first box of the column as if it were another
enclosure and will be locked with safety pins. The other
enclosures will be joined below it as indicated.

2

nº11

nº1

AX-VT20

3

IMPORTANT SAFETY WARNING

Maximum number with AX-VT20:

5 VANTEC-20A-----0 VANTEC-118A
4 VANTEC-20A-----2 VANTEC-118A
3 VANTEC-20A-----3 VANTEC-118A
2 VANTEC-20A-----3 VANTEC-118A
1 VANTEC-20A-----4 VANTEC-118A
0 VANTEC-20A-----4 VANTEC-118A

Manual del Usuario / vantec series / User’s Manual

21

TRD-2 and TRD-6

The VANTEC-20A unit has a tripod socket on its
underside that allows a box angle between + 25º
and -10º when placed on a TRD-2 tripod or on a TRD-6
pole. It is only possible to use one unit in this way.

The VANTEC-118A and VANTEC-218A enclosures
have a socket for a TRD-6 pole.

-10º

TRD-6

TRD-2

7.5º

25º

VANTEC-20A

TRD-6

VANTEC-218A

Example of VANTEC-20A on VANTEC-218A with TRD-6

22

Manual del Usuario / vantec series / User’s Manual

PL-V T20S

The PL-VT20S platform with WLL = 90 kgf allows
transport of up to 3 stacked units of VANTEC-20A.
Its stacked configuration requires that the
lower enclosure be secured by safety pins by
inserting the sliding attachment plates into the
slots on the platform. The other boxes will be
joined by using the rigging system.

PL-VT20S

PL-VT118S

Safety
pin

PL-V T118S

The PL-V T118S platform with WLL = 150 kgf
allows transport of up to 3 stacked units of VANTEC-
118A. It is necessary to be very careful when moving
the assembly since the enclosures are not
attached to the platform by pins. One VANTEC-118A
can be attached to another.

PL-VT118S

Manual del Usuario / vantec series / User’s Manual

23

ANNEX : Line connections: unbalanced and balanced

There are two basic ways to transport an audio signal with microphone or line level:

Unbalanced line: Utilising a two conductor cable, it transports the signal as the voltage between them.
Electromagnetic interference can get added to the signal as undesired noise. Connectors that carry
unbalanced signals have two pins, such as RCA (Phono) and ¼” (6.35mm, often referred to as jack) mono. 3
pin connector such as XLR (Cannon) may also carry unbalanced signals if one of the pins is unused.

Balanced line: Utilising a three conductor cable, one of them acts as a shield against electromagnetic
noise and is the ground conductor. The other two have the same voltage with respect to the ground
conductor but with opposite signs. The noise that cannot be rejected by the shield affects both signal
conductors in the same way. At the device’s input the two signals get summed with opposite sign, so that
noise is cancelled out while the programme signal doubles in level. Most professional audio devices use
balanced inputs and outputs. Connectors that can carry balanced signal have three pins, such as XLR
(Cannon) and ¼” (6.35mm) stereo.

The graphs that follow show the recommended connection with different types of connectors to
balanced processor or amplifier inputs. The connectors on the left-hand side come from a signal source, and
the ones on the right hand side go to the inputs of the processor or amplifier. Note that on the unbalanced
connectors on the left-hand side, two terminals are joined inside the connector. If hum occurs with balanced
to balanced connections, try disconnecting the sleeve (ground) on the input connector. Note that the
illustrations show what should be connected to what, but that pin locations on an actual XLR connector are
different. Also, pin 2 hot is assumed on XLR connectors.

24

Manual del Usuario / vantec series / User’s Manual

www.dasaudio.com

UM_VT3_02_EN

DAS Audio Group, S.L.

C/. Islas Baleares, 24
46988 Fuente del Jarro
Valencia, SPAIN
Tel. [phone]

DAS Audio of America, INC.

6900 NW 52th Street
Miami, FL. 33166 - U.S.A.
TOLL FREE: 1 888 DAS 4 USA

DAS Audio Asia PTE. LTD.

3 Temasek Avenue, Centennial
Tower #34-36
Singapore 039190
Tel. [phone]

DAS do Brasil LTDA.

Rua Dos Andradas, 382 SL
Santa Efigênia, São Paulo
Brasil. CEP: 01208-000
Tel. [phone]