Page 1
User's Manual
series
LX-218C / LX-218C-R
Antes de utilizar el equipo, lea la sección
“Precauciones de seguridad” de este manual.
Conserve este manual para futuras consultas.
Before operating the device, please read the
“Safety precautions” section of this manual.
Retain this manual for future reference.
Page 2
CONTENTS
SAFETY PRECAUTIONS
WARRANTY
DECLARATION OF CONFORMITY
INTRODUCTION
LINE DRAWINGS
SPECIFICATIONS
INSTALLATION
Connectors
Rigging system
Accessories and rigging hardware
ANNEX: Table for cable selection
3
4
5
6
7
7
8 - 13
14
Manual del Usuario / LX series / User’s Manual
Page 3
Precauciones de Seguridad
series
Cajas acústicas pasivas / Passive loudspeaker enclosures
Safety Precautions
Conserve y lea todas estas instrucciones.
Siga todas las advertencias.
El signo de exclamación dentro de un triángulo indica la
existencia de componentes internos cuyo reemplazo puede
afectar a la seguridad.
El doble cuadrado indica equipo de Clase II. The double square indicates Class II device.
Las especificaciones se encuentran en la etiqueta de la parte
posterior del producto.
No exponga este equipo a la lluvia o humedad. No exponga el
equipo a salpicaduras ni coloque sobre él objetos que
contengan líquidos, tales como vasos y botellas. Equipo IP-20.
Este símbolo indica que el presente producto no puede ser
tratado como residuo doméstico normal, sino que debe
entregarse en el correspondiente punto de recogida de equipos
eléctricos y electrónicos.
Equipo diseñado para funcionar entre -25ºC y 45ºC. La
humedad relativa máxima del 95%.
El cableado exterior conectado al equipo requiere de su
instalación por una persona instruida o el uso de cables flexibles
ya preparados.
Keep these instructions.
Heed all warnings. Follow all instructions.
The exclamation point inside an equilateral triangle indicates the
existence of inter nal components whose substitution may affect
safety.
The specifications can be found on the rear label of the product.
Do not expose this device to rain or moisture. Do not place any
objects containing liquids, such as bottles or glasses, on the top
of the unit. Do not splash liquids on the unit. IP-20 equipment.
This symbol on the product indicates that this product should
not be treated as household waste. Instead it shall be handed
over to the applicable collection point for the recycling of
electrical and electronic equipment.
Working temperature ranges from -25ºC to 45ºC. The maximum
relative humidity of 95%.
The outer wiring connected to the device requires installation by
an instructed person or the use of a flexible cable already
prepared.
El equipo cuenta con dos conectores de entrada en paralelo
para facilitar la conexión de varias cajas en paralelo.
No emplace altavoces en proximidad a equipos sensibles a
campos magnéticos, tales como monitores de televisión o
material magnético de almacenamiento de datos.
El colgado del equipo sólo debe realizarse utilizando los herrajes
de colgado recomendados y por personal cualificado. No
cuelgue la caja de las asas.
No existen partes ajustables por el usuario en el interior de este
equipo. Cualquier operación de mantenimiento o reparación
debe ser realizada por personal cualificado. Es necesario el
servicio técnico cuando el aparato se haya dañado de alguna
forma, tal como que haya caído líquido o algún objeto en el
interior del aparato, haya sido expuesto a lluvia o humedad, no
funcione correctamente o haya recibido un golpe.
Limpie con un paño seco. No use limpiadores con disolventes.
Note that the two Speakon input connectors are wired in parallel
to provide easy parallel connection of several enclosures.
Do not place loudspeakers in proximity to devices sensitive to
magnetic fields such as television monitors or data storage
magnetic material.
The appliance should be flown only from the rigging points and
by qualified personnel. Do not suspend the box from the
handles.
No user serviceable parts inside. Refer all servicing to qualified
service personnel. Servicing is required when the apparatus has
been damaged in any way, such as power-supply cord or plug is
damaged, liquid has been spilled or objects have fallen into the
apparatus, the apparatus has been exposed to rain or moisture,
does not operate normally or has been dropped.
Clean only with a dry cloth. Do not use any solvent based
cleaners.
Manual del Usuario / LX series / User’s Manual
3
Page 4
GARANTÍA
Todos nuestros productos están garantizados por un periodo de 24
meses desde la fecha de compra.
Las garantías sólo serán válidas si son por un defecto de
fabricación y en ningún caso por un uso incorrecto del producto.
Las reparaciones en garantía pueden ser realizadas,
exclusivamente, por el fabricante o el servicio de asistencia técnica
autorizado.
Otros cargos como portes y seguros, son a cargo del comprador
en todos los casos.
Para solicitar reparación en garantía es imprescindible que el
producto no haya sido previamente manipulado e incluir una
fotocopia de la factura de compra.
WARRANTY
All our products are warrantied against any manufacturing defect
for a period of 2 years from date of purchase.
The warranty excludes damage from incorrect use of the product.
All warranty repairs must be exclusively undertaken by the factory
or any of its authorised service centers.
To claim a warranty repair, do not open or intend to repair the
product.
Return the damaged unit, at shippers risk and freight prepaid, to
the nearest service center with a copy of the purchase invoice.
4
Manual del Usuario / LX series / User’s Manual
Page 5
DECLARACIÓN DE CONFORMIDAD
DECLARATION OF CONFORMITY
DAS Audio Group, S.L.
C/ Islas Baleares, 24 - 46988 - Pol. Fuente del Jarro - Valencia. España
(Spain).
Declara que y :LX-218C LX-218C-R
Declares that and :LX-218C LX-218C-R
Cumple con los objetivos esenciales de las Directivas:
Abide by essential objectives relating Directives:
l De Baja Tensión / Low Voltage 2014/35/UE
l RoHS 2011/65/UE
l RAEE (WEEE) 2012/19/UE
Y es conforme a las siguientes Normas Armonizadas Europeas:
In accordance with Harmonized European Norms:
l EN 60065:2014.- Audio, video and similar electronic apparatus. Safety
requirements.
l EN 50581:2012.- Technical documentation for the assessment of
electrical and electronic products with respect to the restriction of
hazardous substances.
Manual del Usuario / LX series / User’s Manual
5
Page 6
INTRODUCTION
The LX series subwoofers from DAS Audio are systems which use twin LXN long excursion loudspeakers
incorporating light weight neodymium magnet assemblies and the efficient TAF (Total Air Flow) heat
evacuation scheme. The units are ideal for applications requiring high level sub-bass extension in mid to
large-scale outdoor/indoor events in arenas, stadiums or theaters. The LX enclosures are constructed of 18
mm birch plywood finished with the durable Iso-Flex black paint. The rectangular shape facilitates stacking
and use in cardioid configurations and presents a bass-reflex configuration.
Two versions are available for this passive model, without rigging hardware or “R” version. The “R” version
is equipped with a captive rigging system that is compatible with DAS Aero line array system accessories.
So, the models will be LX-218C and LX-218C-R.
To make transporting the systems easier, the LX-218C and LX-218C-R systems have an optional dolly
platform, the PL-218CS. The maximum number of units that can be stacked on a dolly is three.
The LX-218C-R is equipped with a front located dolly panel, the PL-LX218C, which is attached by way of
the rigging hardware.
Other interesting accessories have been compiled in the Summary table of accessories (chart below). In
the RIGGING SECTION, more detail is provided for the accessories mentioned below.
LX-218C / LX-218C-R
Rigging (only ‘R’ version)
Rigging Kit to convert to ‘R’ version
To transport
To combine with other systems
(only ‘R’ version)
Summary table of accessories
AX-AE50
KIT-R-LX218C
KIT-W100
PL-218CS
PL-LX218C (only ‘R’ version)
PICKUP-AX-AE50
AX-COMBO12
LX-218C
+
LX-218C-R
KIT-R-LX-218C
Explanatory images of the 'R' version
6
Manual del Usuario / LX series / User’s Manual
Page 7
LINE DRAWINGS
1280
550
632
LX-218C LX-218C-R
ALL DIMEN SIONS IN MIL LIMETERS
SPECIFICATIONS
MODEL
Frequency Range (-10 dB)
RMS (Average) Power Handling
On-Axis Sensitivity 1 W / 1 m
LX-218C / LX-218C-R
28 Hz - 100 Hz
(1)
2000 W
103 dB SPL
1350
550
696
(2)
Rated Maximum Peak SPL at 1 m
Transducers/Replacement Parts
Nominal Impedance
Recommended Amplifier Power
142 dB
2 x 18LXN/GM-18LX
4 ohms
2 x 2400 W @ 4 ohms
(2 units LX-218C )
Enclosure Geometry
Enclosure Material
Color/Finish
Rigging System
Rectangular
Birch Plywood
Black Paint
Ground Stackable
Integrated in box design (R)
Connectors
Dimensions (H x W x D)
Weight
2 X NL8 wired ±1
55x128x63.2 cm /
22x51x24.9 in /
55x135x69.6 cm
22x54x27.4 in
78.5 kg / 176.1 lb (LX-218C)
94.5 kg / 207.9 lb (LX-218CR)
Accessories
AX-AE50 Rigging Grid (R)
AX-COMBO12 Rigging Adapter (R)
KIT-R-LX218C Rigging Hardware Kit
KIT-W100 Caster Kit
PICKU-AX-AE50
PL-LX218C Dolly Panel (R included)
PL-218CS Flat Bed Dolly
Notes: 1. Based on a 2 hour test continuously applying 6 dB crest factor pink noise (IEC shaped).
2. Maximum calculated Peak SPL based on sensitivity and RMS power handling.
Manual del Usuario / LX series / User’s Manual
7
Page 8
INSTALLATION
Connectors
The DAS LX-218C / LX-218C-R are designed to facilitate the connection for installations, they have been
provided with connectors, NL8 type, standard for professional audio equipment. These connectors are
connected in parallel, so that we can carry the amplified audio signal up to a device and we can forward it to
the next box, very easily. The polarity of the connectors and other important information for proper
connection is indicated on the silkscreen.
Detail of the connectors and the silkscreen of LX-218C and LX-218-R.
Rigging system
This manual contains needed information for flying DAS Audio line array systems, description of the
elements and safety precautions.
To perform any operations related to flying the system, read the present document first, and act on the
warnings and advice given.
The goal is to allow the user to become familiar with the mechanical elements required to fly the acoustic
system, as well as the safety measures to be taken during set-up and teardown.
8
Manual del Usuario / LX series / User’s Manual
Page 9
Only experienced installers with adequate knowledge of the equipment and local safety regulations
should fly speaker boxes.
It is the user's responsibility to ensure that the systems to be flown (including flying accessories) comply
with state and local regulations.
The working load limits in this manual are the results of tests by independent laboratories. It is the user's
responsibility to stay within safe limits. It is the user's responsibility to follow and comply with safety factors,
resistance values, periodical supervisions and warnings given in this manual.
Product improvement by means of research and development is on going at DAS Specifications are
subject to change without notice.
It’s common practice to apply 5:1 safety factors for enclosures and static elements.
For slings and elements exposed to material fatigue due to friction and load variation the following ratios
must be met; 5:1 for steel cable slings, 4:1 for steel chain slings and 7:1 polyester slings.
Thus, an element with a breaking load limit of 1000 kg may be statically loaded with 200 kg (5:1 safety
factor) and dynamically loaded with 142 Kg (7:1 safety factor).
For the working load of each lift motor must be used a safety factor of 10:1.
When flying a system, the working load must be lower than the resistance of each individual flying point in
the enclosure, as well as each box.
Hanging hardware should be regularly inspected and suspect units replaced if in doubt.
This is important to avoid injury and absolutely no risks should be taken in this respect. It is highly
recommended that you implement an inspection and maintenance program on flying elements, including
reports to be filled out by the personnel that will carry out the inspections.
Local regulations may exist that, in case of accident, may require you to present evidence of inspection
reports and corrective actions after defects were found.
Absolutely no risks should be taken with regards to public safety. When flying enclosures from ceiling
support structures, extreme care should be taken to assure the load bearing capabilities of the structures so
that the installation is absolutely safe.
Do not fly enclosures from unsafe structures.
Consult a certified professional if needed.
All flying accessories that are not supplied by D.A.S. Audio are the user's responsibility.
Use at your own risk.
NOTE: DAS Audio recomends that you meet the essential objectives set out on Directive
2009/104/EC concerning the minimum safety and health requirements for the use of work
equipment at work by workers. Specifically, for rigging systems, see the Annex I, point 3.2, and
the Annex II, point 3, about lifting loads.
Accessories and rigging hardware
DAS Audio LX-218C-R, include two rigging structures on each side of the box. Manufactured from zinc
plated steel they are painted black and are affixed to an internal plate with special crop resistant screws. Two
special stainless steel cam links are assembled to each of the structures, allow for stacking or flying of boxes.
On each cabinet are included six quick release pins.
The front rigging guide is used to provide a rigid coupling of a unit and the box above. Whether stacked
or flown, the rear guide is used to determine the splay angle between units depending on the hole in which
the quick release safety pin is inserted.
Note: With the LX-218C only stacking is possible because is not equipped with rigging hardware.
Ø=8mm ; L=35mm
Pasadores de seguridad
Quick release pin
Manual del Usuario / LX series / User’s Manual
Guías de LX series
LX series Guides
9
Page 10
W.L.L. 1700Kg
4º
2º
0º
æro / AX-combo
CAUT ION!
USE ONLY 1
SAFE TY PI N
LX
0º
0º
STACK
FLY
W.L.L. 1700Kg
4º
combo
2º
/ AX-
0º
æro
CAUTION!
USE ONLY 1
SAFETY PIN
LX
STACK
0º
FLY
0º
Etiqueta de los herrajes de LX-218C-R
LX-218C-R rigging hardware label
To facilitate the correct positioning of the guides in the corresponding angle hole of the upper unit (using
the quick release safety pins), a sticker indicates the splay angle obtained whether stacked or flown. To
secure the guides in the angle holes, 8 mm high resistance quick release safety pins are used (6 pins per
unit).
To fly the systems and define the splay angles, the pin should be inserted in the slot of the rear guide. To
stack the systems, the pin should be inserted in the hole of each guide.
In most cases, to join one box to another the procedure described above will suffice. We will proceed to
describe other accessories available for safe and simple stacking, transport and flying of the systems.
AX-AERO50
This accessory can be used with aero-50, also. This rigging structure is comprised of a steel central bar
and two detachable side panels that are fixed using high resistance quick release safety pins.
They have a centrally located reinforcement which is used to attach the lifting cables. Depending on the
position of the safety pins, the array will achieve a different angle of inclination (see the positions marked on
the side panels).
The first box will be attached to this structure using 6 safety pins according to the procedure described
on the preceding pages. Once this is accomplished, the structure can be left with a vertical orientation taking
into account the position of the safety pin. With the use of the EASE Focus simulation program, determine
what position should be used to achieve the desired array inclination.
AX-AE50
10
Peso: 51 Kg
Weight: 112.2 lbs
Dimensiones (Al x An x P): 430 x 1440 x 721 (mm)
Dimensions (H x W x D): 16.9 x 56.7 x 28.4 (in)
W.L.L.: 1700 kgf
Manual del Usuario / LX series / User’s Manual
Page 11
We will show the cardioid configurations separately in order to appreciate the differences and
similarities.
OMNIDIRECTIONAL CARDIOID
1
Join
cabinets.
Turn guide.
1
Turn guide.
2
2
Turn
guide.
3
4
Insert
Pin.
3
Insert Pin.
Join
cabinets.
Insert Pin.
5
4
Turn
guide.
5
Insert
Pin.
6
Raise
cabinet.
Insert Pin.
6
Raise
cabinet.
7
7
Insert
Pin.
Manual del Usuario / LX series / User’s Manual
11
Page 12
17
16
15
14
12
11
10
8
6
10
8
14
12
17
15
REAR
20
18
MAX. NUMBER OF UNITS ALLOWED
8
13
14
15
17
19
LX
æro
16
1
2
3
4
5
6
7
FRONT
1
2
3
4
5
6
7
8
99101011111212131314141515161617
13
14
15
æro
LX
16
17
16161616161616161616161616
19
20202020202020202020202020
MAX. NUMBER OF UNITS ALLOWED
15
14
12
11
10
8
18
17
15
14
12
6
10
8
REAR
FRONT
AX-AE50 silkscreen
Rigging kit “R”
Kits are available to transform “stackable only” cabinets to flyable ones. For example, the LX-218C can be
upgraded to an LX-218C-R by using the KIT-R-LX218C.
KIT-R-LX218C
Front located dolly platforms PL-LX218C
The front located dolly platforms are accessories available for the LX-218C. “R” versions include the front
dolly. These platform dollies are used for the transport of individual units and to facilitate rigging. The
platforms are attached to the front rigging hardware of each unit by way of captive pins located on the
platform.
12
PL-LX218C
Manual del Usuario / LX series / User’s Manual
Page 13
KIT-W100 & platform PL-218CS.
Transport accessories include the KIT-W100 caster kit and PL-218CS dolly panel for the LX-218C and LX-
218C-R.
The caster kit will not impede cabinet stacking as the wheels are attached to the rear panel of the
cabinet. As a safety precaution when maneuvering cabinets, the dolly panels should not exceed a maximum
of three (3) units.
PL-218CS
KIT-W100
Manual del Usuario / LX series / User’s Manual
13
Page 14
ANNEX : Table for cable selection
This table shows the power loss in % and dB, for different cable lengths and sections shown. It is
recommended that the losses do not exceed 30% in any case (around 3dB). Although it is recommended
minimizing losses, the maximum acceptable losses are usually around 15% (approximately 1.4dB).
14
Manual del Usuario / LX series / User’s Manual
Page 15
www.dasaudio.com
UM_LX218C_03_EN
DAS Audio Group, S.L.
C/. Islas Baleares, 24
46988 Fuente del Jarro
Valencia, SPAIN
Tel. +34 96 134 0860
DAS Audio of America, INC.
6900 NW 52th Street
Miami, FL. 33166 - U.S.A.
TOLL FREE: 1 888 DAS 4 USA
DAS Audio Asia PTE. LTD.
3 Temasek Avenue, Centennial
Tower #34-36
Singapore 039190
Tel. +65 6549 7760
DAS do Brasil LTDA.
Rua Dos Andradas, 382 SL
Santa Efigênia, São Paulo
Brasil. CEP: 01208-000
Tel. +551133330764
Loading...