Page 1
Assembly Instructions
Caution : You must read this before you proceed
Bar Table
CAUTION : This table is NOT a TOY.
Keep your child / children at bay during the assembly process.
Parts list
Label Picture QTY
A Table Top 1
B
Table Leg with pre-
attached Leveller
4
C Round Support 2
Page 1 OF 8
Page 2
Hard ware
Label Picture Description QTY
①
Bolt(M8*30mm) 5
②
Washer(8mm) 13
③
Spring Washer(8mm) 13
④
Nut(8mm) 5
⑤
Hex Bolt(M8*30mm) 9
⑥
Spanner 1
⑦
Screwdriver 1
⑧
Rubber Cap 5
Assembly Preparation
Before
Beginning
Assembly:
Page 2 OF 8
Page 3
Assembly Step
Overview
This Table has multiple parts and may require up to some 30 minutes to
assemble.
To give you an overview of the Table parts, the above picture is to help
you put the various parts into perspective.
Please read through the instructions below to familiarise yourself with
the parts and steps before assembly.
Table Top(A)
Table Leg with preattached Leveller(B)
Round
FRONT FACING
Page 3 OF 8
Page 4
Step 1
Unpack and place all parts on a clean, soft surface.
Step 2
Lay the Table Top(A), facedown, onto a flat, soft, clean surface and lock
the mounting positions with bolts(①) by using screwdriver(⑥).
Need tighten the bolts.
Page 4 OF 8
Page 5
Step 3
Attach the Table Leg with pre-attached Leveller(B) to the Table Top(A)
with washers(
②
)
,spring washers(
③
)
,and nuts(
④
)
using spanner(
⑦
)
.
DO NOT OVERTIGHTEN.
Step 4
Repeat step 3, attaching the remaining 3 legs to the Table Top(A).
At this stage, only loosely tighten the bolts.
Page 5 OF 8
Page 6
Step 5
Loosely attach the Round Support (C) to Table Leg with pre-attached
Leveller(B) with washers(
②
)
,spring washers(③) and hex nuts(
⑤
)
using
spanner(
⑦
)
.
DO NOT OVERTIGHTEN.
Step 6
Loosely attach the Round Support (C) to Table Leg with pre-attached
Leveller(B) with washers(②),spring washers(③) and hex nuts(⑤) using
the spanner(⑦).
DO NOT OVERTIGHTEN.
Page 6 OF 8
Page 7
Step 7
Stand the table right side up.
Tighten the Levellers.
Inspect it and make sure all parts are adequately connected.
Now, fully and securely, tighten all nuts, at all joints.
When tightening the Bolts, tighten sequentially.
DO NOT tighten any Bolt fully and then move on to the next one.
If there is still wobbles, loosen the bolts and execute this same
process.
If the Table is not stable it could lead to damage to the product.
Step 8
Adjust the Legs pre-installed Levellers until the Table is level with the
ground.
Add Rubber Caps(⑧) on all bolt ends to protect skin or clothing from
getting snagged.
Caution: This TABLE can only be used on a flat, level surface.
Adjust
Adjust low
Page 7 OF 8
Page 8
Do not put hot items directly on furniture surface.
Do not clean furniture with harsh cleansers or polish.
To obtain the longest lifespan of your outdoor prodcts,
minimizing exposure to direct sunlight is recommended.
Children should not climb or jump on the furniture.
Do not write on furniture without a padded barrier to
protect the surface.
To obtain the longest lifespan of your outdoor products,
avoid extended and lengthy exposure to rain, snow,
and direct sunshine. Whenever possible cover the
product and /or place under patio or awnings.
Not for commercial use. For residential use only .
Stains may be removed with mild soap solution and
damp cloth.
Dust and pick-up spills using a clean, non-colored,
lint-free cloth .
Page 8 OF 8
Loading...