Page 1
Caution: You must read this before you proceed.
Bar Chair
Page 1 OF 9
Page 2
Part NO. Picture Description QTY
A Chair Back 1 PC
B Chair Seat 1 PC
C Left Front Leg 1 PC
D Right Front Leg 1 PC
E Left Side Rail (labeled) 1 PC
F Right Side Rail (labeled) 1 PC
G Front Rail (labeled) 1 PC
Label Picture Description QTY
①
②
Bolt(M6x80mm)
Bolt(M6x50mm)
4 PCS
4 PCS
Bolt(M6x45mm)
③
2 PCS
Screw(M4x32mm)
④
6 PCS
Spring Washer
⑤
10 PCS
Washer
⑥
10 PCS
⑦
⑧
Allen Key
Screwdriver
Page 2 OF 9
1 PC
Not
provided
Page 3
Before Beginning Assembly:
Pack A for assembling the
Seat Frame(B) to the hind
legs of Chair Back(A)
Pack B for assembling the
Seat Frame(B) to the Front
Leg Left(C) & Front Leg
Right(D)
Pack C for assembling the
Seat Frame (B) to the
horizontal panel of Chair
Back (A) at the central point
Pack D for assembling the
Left Side Rails(E) &Right
Side Rails(F) to the Left Front
Leg （C）&Right Front Leg
(D)
Pack E for assembling the
Left Side Rails(E) &Right
Side Rails(F) to the Chair
Back（A）
Bolt(M6x80mm)+
Washer
+Spring Washer
Bolt(M6x50mm)+
Washer
+Spring Washer
Bolt(M6x45mm)+
Washer
+Spring Washer+
Allen Key
Screw(M4x32mm)
Screw(M4x32mm)
Pack F for assembling the
Front Rail(G) to the Front Leg
Screw(M4x32mm)
Page 3 OF 9
Page 4
Chair Back (A)
Chair Seat (B)
Left Leg (C)
Left side Rail (E)
Front Rail (F)
Right side Rail (F)
FRONT FACING
Right Leg (D)
This Bar Chair has multiple parts and may require up to 30 minutes to assemble. To give
you an overview of the Bar Chair parts, the above picture is to help you put the various
Table parts into perspective.
Please read through the instructions herebelow to familiarise yourself with the parts and
steps before assembly.
Step 1
A. Chair Back
B. Chair Seat with Black
Calico/magicTapes
C. Front Left Leg & D. Front Right
Leg
E. Left Side Rail & F.
Right Side Rail
G. Front Rail
Place the Chair Back(A) and Chair Seat(B) on a clean, non-marring surface.
Remove the Seat Base Cover from the underside of the Chair Seat(B) and take out all of the Parts
and Hardware.
Page 4 OF 9
Page 5
Step 2
Align the mounting positions of the Chair Back(A) and Chair Seat Frame(B).
Use your left hand to push the seat frame floorwards, depicted by Arrow 1, this action helps to
ensure the Chair Seat(B) is pressed towards to the Chair Back(A) with no gap between them.
Then, lock the middle mounting point by using Hardware Pack C and the corner mounting points by
using Hardware Pack A with The Allen Key(7),
Caution : At this stage, LOOSELY FASTEN these bolts
Step 3
Insert the Front Rail(G) into the oval housing of Left Front Leg (C) & Right Front Leg (D)
as shown above.
Then, use Hardware Pack F to attach the Front Rail(G) to the Left Front Leg (C) & Right Front Leg
(D).
At this stage, LOOSELY FAST EN these bolts
Page 5 OF 9
Page 6
Step 4
D
C
A
B
Place the chair onto the side of a table as seen in picture. Whith your assistant help to hold the
front leg frame insert to the Chair Seat (B)
Step 5
Step 5.1
Pushing
outwards
F
B
A
Step 5.2
F
E
E
A
A
B
5.1 Place Right Side Rail (F) Into the housing of the Hind Leg of the chair Back (A) and
Right Leg (D).
You may need to apply a little pressure to the front leg frame - pushing outwards, so as to
enable the Side Rail (F) to be slotted into position.
5.2 Repeat the same prooess to install the Left side Rail (E).
Page 6 OF 9
Page 7
Step 6
D
6
5
2
7
C
B
Attach the Left Front Leg (C) And Right Front Leg (D) to the Chair Seat (B) Using Pack B.
At this stage, only LOOSELY FASTEN the Bolts.
Step 7
F
E
D
8
4
E
C
B
Then use Pack D & Pack E to attach Side Rail (E) and Side Rail (F) to the Chair Back (A) and
Left Leg (C) and Right Leg (D).
At this Stage, only LOOSELY FASTEN the Screws
Step 8
If wobble
1
3
Test aganin
2
30-50cm
Page 7 OF 9
Page 8
Place the chair on a Level Surface to check if it wobbles.
If it is wobbles, lift the chair some 30cm to 50cm high from the ground, keep your feet and
toes well away from the drop zone, and drop the chair freely and vertically with the four legs,
hitting the ground at the same time.
This
Drop Test will help to ensure that all the bolts and gaps to all reach full alignment. test again
for evenness on a Level Surface.
If no wobbles are found, proceed to tighten all the Bolts.
Caution: When tightening the Bolts, tighten sequentially.
Do not tighten any screw fully and then towards the next one,this would cause the frame to
warp. If it still wobbles, loosen the bolts and execute this same drop test.
If the Chair is not Stable it could lead to damage to the product.
Step 9
Place the Seat Base Cover back underneath the chair seat (as shown in picture) from where it was
removed from originally.
Smooth down with your hand on the Magic Tape on all 4 sides at the edge of the seat box.
Step 10
Turn the chair right way up, it is now ready for use.
Caution:This Bar Stool can only be used on a flat, level surface.
Page 8 OF 9
Page 9
Page 9 OF 9
Loading...