Dapper Lighting 575 Install Manual

575 Install Guide - HID

The 575 System uses H11 bulbs on both high and low beams. Included is an adapter that will convert
your OEM H4 plug to an H11 socket. If you have purchased an HID package, you will receive bulbs and
ballasts that use slightly different wiring.

This is a TEMPORARY install guide until our new HID relay harness’ arrive. You will recieve instructions on
the new harness when you receive them (ETA June/July). The new harnesses will allow you to keep the
low beams on while on high beam for added performance.

1

Remove your current headlamps. Be careful not to tamper
with your headlight adjustment screw (if applicable) otherwise re­aligning your headlamps will be a much longer process.

2

Set your old headlamps aside, and grab your new set
of Dapper Lighting 575 series headlamps. Replace your old
headlamps with your Dapper Lighting 575’s using the same
mounting locations as before. All of our tabs match up to your
OEM bucket and should require no modication. Your OEM
headlight retaining rings will also t directly over your new Dapper
Lighting headlamps. (Note: Be cautious that you are installing the
new headlamps in their proper positions. Make sure none of the
headlamps are upside down, and make sure your low beams and
high beams are in their respective locations as well.)

3

Make sure your Dapper Lighting 575 headlamps t without
issue (i.e. not rubbing against your radiator support, causing
clearance issues, or preventing a ush mount). Once you’ve got
the lamps in, it’s time to install the bulbs, pop together a couple
connections, and nd ballast mounting locations before you’re
ready to turn everything on.

4

Locate your included HID bulbs. Secure them into your Dapper
Lighting 575 headlamps by lining up the locking tabs and then
spinning clockwise to lock the bulb in place. The bulb should sit
completely ush against the base of the headlamp or it may be out
of focus.

5

Now, locate your HID ballasts. There are two wires coming out
from the ballast, as well as two wires coming from the back of your
HID bulbs. Clip the two from the ballast into the two from your HID
bulbs together (there is only one way they will snap together, so
don’t worry about polarity here).

Phone: [phone] dapperlighting.com

6

Now locate your Dapper
Lighting H11-9006 adapter.
Take the 9006 end of your
9006-H11 adapter with the
blue connector and plug it
into the HID ballast. Make
sure you use the small
TRIANGULAR tab on the HID
ballast to clip onto (if you clip
onto the larger square tab, you will have reversed polarity and the lights won’t turn on.) Then, take other
end of the H11-9006 adapter (H11 end) and plug it into the H11 end of your Dapper Lighting H4-H11
adapter.

7

Take the black end of your H4-H11 adapter with the 3-pronged
plug and MAKE SURE the gold pins in our adapter match up to
the individual slots on your OEM plug. In other words, make sure
the RED (power) pin is connected to your low beam (“drive”) slot,
and your BLACK (ground) pin is connected to your ground slot.
Once you’re sure the adapter pins and your OEM plug are lined up
properly, plug it in and turn on your headlamps.

8

If your low and high beam headlights both turn on as they should then your install is complete. The
nal step is to make sure you have the beams aligned optimally. You can nd instructions on how to do
so on our website at www.dapperlighting.com.

9

If you nd that your headlamps aren’t turning on, or seem to be working on only high beam or only
low beam, double check the gold pins on the male end of our H4-H11 adapter, as you may have them in
the wrong spots. The pins can be removed using a small athead screwdriver, and swapped in order to
match up with your vehicle’s plug setup. Please feel free to give us a call regarding install ANY time and
we’ll have a tech assist you.

10

Send us pictures! We love seeing how Dapper Lighting looks and performs on your ride! Email,
DM, tag us, etc. for a chance to be featured in our newsletter, on our social media pages, website, and
catalog! Thanks again from the team at Dapper.

For technical questions please contact us at:

415-493-8236

[e-mail]

Phone: [phone] dapperlighting.com