Page 1
EDGE EBS-1 V2
Highlite International B.V. – Vestastraat 2 – 6468 EX – Kerkrade – the Netherlands
Order code: D1476B
MANUAL
ENGLISH
Page 2
1
Order code: D1476B
EDGE EBS-1
Table of contents
Warning ............................................................................................................................................................................... 2
Safety Instructions ...................................................................................................................................................... 2
Operating Determinations ....................................................................................................................................... 4
Connection with the Mains ..................................................................................................................................... 4
Return Procedure ...................................................................................................................................................... 5
Claims .......................................................................................................................................................................... 5
Description of the Device ................................................................................................................................................ 6
Overview ..................................................................................................................................................................... 7
Transmitter (Front/Back) ...................................................................................................................................... 7
Transmitter (Top/Bottom) .................................................................................................................................... 7
Receiver (Front) .................................................................................................................................................... 8
Receiver (Back) .................................................................................................................................................... 8
Installation ........................................................................................................................................................................... 8
Mounting – Single Receiver ..................................................................................................................................... 8
Mounting – Multiple Receivers ................................................................................................................................ 9
Setup Examples .......................................................................................................................................................10
4 x EDGE EHS-1 ....................................................................................................................................................10
8 x EDGE EHS-1 ....................................................................................................................................................11
Setup and Operation ......................................................................................................................................................12
Receiver Setup .........................................................................................................................................................12
Transmitter Setup .....................................................................................................................................................13
Example 1 – Headset .........................................................................................................................................13
Example 2 – Electric Guitar ..............................................................................................................................13
Belt Clip Orientation ..........................................................................................................................................13
Control Panel ...........................................................................................................................................................14
Inserting the Batteries .............................................................................................................................................14
Compensation of Interference with Balanced Connections .........................................................................15
Main Menu Options ................................................................................................................................................15
1. Group ...............................................................................................................................................................16
2. Channel ...........................................................................................................................................................16
3. Freq ...................................................................................................................................................................17
4. Scan..................................................................................................................................................................18
5. Sync ..................................................................................................................................................................18
6. Lock ..................................................................................................................................................................19
7. Tx Gain .............................................................................................................................................................19
8. Rx Gain .............................................................................................................................................................19
9. Low Cut ............................................................................................................................................................20
10. Squelch ..........................................................................................................................................................20
11. Tone Key ........................................................................................................................................................20
12. Color ...............................................................................................................................................................21
13. Name .............................................................................................................................................................21
14. Ant Dc ............................................................................................................................................................22
Transmitter .................................................................................................................................................................23
Mute .....................................................................................................................................................................23
Lock ......................................................................................................................................................................23
Main Menu Options ...........................................................................................................................................23
Connection Cables .........................................................................................................................................................25
Maintenance ....................................................................................................................................................................26
Troubleshooting ...............................................................................................................................................................26
Approval ...........................................................................................................................................................................27
Product Specifications ....................................................................................................................................................28
Dimensions ........................................................................................................................................................................29
Page 3
2
Order code: D1476B
EDGE EBS-1
Warning
Unpacking Instructions
Immediately upon receiving this product, carefully unpack the carton and check the contents to ensure
that all parts are present, and have been received in good condition. Notify the dealer immediately and
retain packing material for inspection if any parts appear damaged from shipping or the carton itself
shows signs of mishandling. Save the carton and all packing materials. In the event that a device must be
returned to the factory, it is important that the device is returned in the original factory box and packing.
Your shipment includes:
● DAP Audio EDGE EBS-1 (receiver +
transmitter)
● DC power adapter
● 1 x long mounting bracket
● 1 x short mounting bracket
● 1 x mounting plate
● 1 x mono jack cable (1 m)
● 1 x headset
● User manual
Safety Instructions
Every person involved with the installation, operation and maintenance of this system has to:
● be qualified
● follow the instructions of this manual.
Before the initial start-up, please make sure that there is no damage caused by transportation. Should
there be any, consult your dealer and do not use the system.
To maintain perfect condition and to ensure a safe operation, it is absolutely necessary for the user to
follow the safety instructions and warning notes written in this manual.
Please consider that damages caused by manual modifications to the system are not subject to
warranty.
This system contains no user-serviceable parts. Refer servicing to qualified technicians only.
Page 4
3
Order code: D1476B
EDGE EBS-1
IMPORTANT:
The manufacturer will not accept liability for any resulting damages caused by the non-observance of
this manual or any unauthorized modification to the device.
Before using the device, check the regulations regarding the frequency allocation in your country or
region.
● Never use the device during thunderstorms, unplug the device immediately.
● Never leave various parts of the packaging (plastic bags, polystyrene foam, nails, etc.) within
children’s reach, as they are potential sources of danger.
● Never remove warning or informative labels from the unit.
● Never leave any cables lying around.
● Do not open the device and do not modify the device.
● Do not switch the system on and off in short intervals, as this would reduce the system’s life.
● Only use device indoors, avoid contact with water or other liquids.
● Avoid flames and do not put close to flammable liquids or gases.
● Always disconnect power from the mains, when device is not used or before cleaning! Only handle
the power cord by the plug. Never pull out the plug by tugging the power cord.
● Use only the supplied DC power adapter.
● Make sure that the power cord is never crimped or damaged. Check the system and the power
cord from time to time.
● Make sure that the available voltage is not higher than stated on the rear panel.
● Make sure you do not use the wrong kind of cables or defective cables.
● If system is dropped or struck, disconnect the power supply immediately. Have a qualified engineer
inspect for safety before operating.
● If the system has been exposed to drastic temperature fluctuation (e.g. after transportation), do not
switch it on immediately. The arising condensation water might damage your system. Leave the
system switched off until it has reached room temperature.
● Do not put your equipment next to TV, radio, etc., because of interference or distortion.
● Prevent distortion! Make sure that all components connected to the device have sufficient power
ratings. Otherwise, distortion will be generated because the components are operated at their limits.
● If your DAP Audio device fails to work properly, discontinue use immediately. Pack the unit securely
(preferably in the original packing material), and return it to your DAP Audio dealer for service.
● Please read this manual carefully and keep it for future reference.
● Repairs, servicing and electric connection must be carried out by a qualified technician.
● WARRANTY: Till one year after date of purchase.
Page 5
4
Order code: D1476B
EDGE EBS-1
Operating Determinations
● This device is not designed for permanent operation. Consistent operation breaks will ensure that the
device will serve you for a long time without defects.
● The maximum ambient temperature t
a
= 40 °C must never be exceeded.
● The relative humidity must not exceed 50 % with an ambient temperature of 40 °C.
● If this device is operated in any other way, than the one described in this manual, the product may
suffer damages and the warranty becomes void.
● Any other operation may lead to dangers like short-circuit, burns, electric shock, crash, etc.
You endanger your own safety and the safety of others!
Connection with the Mains
Connect the receiver to the mains with the supplied AC power adapter.
Always pay attention, that the right color cable is connected to the right place.
International
EU Cable
UK Cable
US Cable
Pin
L
BROWN
RED
YELLOW/COPPER
PHASE
N
BLUE
BLACK
SILVER
NEUTRAL
YELLOW/GREEN
GREEN
GREEN
PROTECTIVE GROUND
Make sure that the device is always connected properly to the earth!
Improper installation can cause serious damage to people and property!
Page 6
5
Order code: D1476B
EDGE EBS-1
Return Procedure
Returned merchandise must be sent prepaid and in the original packing, call tags will not be issued.
Package must be clearly labeled with a Return Authorization Number (RMA number). Products returned
without an RMA number will be refused. Highlite will not accept the returned goods or any responsibility.
Call Highlite 0031-455667723 or mail aftersales@highlite.com and request an RMA prior to shipping the
fixture. Be prepared to provide the model number, serial number and a brief description of the cause for
the return. Be sure to properly pack fixture, any shipping damage resulting from inadequate packaging is
the customer’s responsibility. Highlite reserves the right to use its own discretion to repair or replace
product(s). As a suggestion, proper UPS packing or double-boxing is always a safe method to use.
Note: If you are given an RMA number, please include the following information on a piece of paper
inside the box:
01) Your name
02) Your address
03) Your phone number
04) A brief description of the symptoms
Claims
The client has the obligation to check the delivered goods immediately upon delivery for any shortcomings and/or visible defects, or perform this check after our announcement that the goods are at their
disposal. Damage incurred in shipping is the responsibility of the shipper; therefore the damage must be
reported to the carrier upon receipt of merchandise.
It is the customer's responsibility to notify and submit claims with the shipper in the event that a fixture is
damaged due to shipping. Transportation damage has to be reported to us within one day after receipt
of the delivery.
Any return shipment has to be made post-paid at all times. Return shipments must be accompanied with
a letter defining the reason for return shipment. Non-prepaid return shipments will be refused, unless
otherwise agreed in writing.
Complaints against us must be made known in writing or by fax within 10 working days after receipt of the
invoice. After this period complaints will not be handled anymore.
Complaints will only then be considered if the client has so far complied with all parts of the agreement,
regardless of the agreement of which the obligation is resulting.
Page 7
6
Order code: D1476B
EDGE EBS-1
Description of the Device
The EDGE EBS-1 is a wireless beltpack system. The set comes with a beltpack transmitter, a receiver, and a
headset. The EBS-1 is suitable for both vocal and instrumental applications and can be used only with
guitars with an active pickup. The transmitter is powered by two AA 1,5 V batteries (not included).
Features
Receiver
● Modulation: FM
● Power supply: DC 12–15 V, 300 mA
● Frequency range: 606–668 MHz
● Frequency response: 75 Hz–18 kHz
● Sensitivity: -100 dBm/30 dB sinad
● Distortion: <1%(AF1 kHz, RF46 dBu)
● Max SPL: 128 dB SPL
● RF stability: ≤ ± 15 ppm
● Frequency deviation: ± 75 kHz
● Spurious rejection: >50 dB
● SNR: >100 dBA
● Transmission latency: 0 ms
● Audio outputs: 3-pin XLR OUT balanced, mono ¼” jack unbalanced
● Indicators: A/B antenna, AF signal
● Pilot frequency: 32768 kHz
● Output signal sensitivity adjustable range: 48 dB, Adopt 6 dB step for adjustment
● Dimensions: 205 x 170 x 263 mm (LxWxH)
● Weight: 1,24 kg
Transmitter
● Input: 3-pin mini XLR
● Input impedance: 1 mΩ
● Output gain range: 30 dB
● RF output: 10 mW*/20 mW/30 mW
● Power supply: 2 x AA 1,5 V batteries (not included)
● Dimensions: 63 x 21 x 215 mm (LxWxH)
● Weight: 0,18 kg
* - The maximum allowed RF output is 10 mW. The use of outputs stronger than 10 mW must be permitted
by the local authorities.
Optional accessories:
98043 – Procell alkaline battery (AA LR6 1,5 V)
D1417 – DAP GC-1 (guitar cable 6,3 mm jack to 4-pin XLR)
Page 8
7
Order code: D1476B
EDGE EBS-1
Overview
Transmitter (Front/Back)
Fig. 01
01) Antenna
02) OLED display
03) Power button
04) DOWN button
05) UP button
06) Belt clip
Transmitter (Top/Bottom)
Fig. 02
07) Mute switch ON/OFF
08) 3-pin mini XLR headset connector OUT
09) IR sensor
10) Battery housing (2 x AA)
11) Lock switch
Page 9
8
Order code: D1476B
EDGE EBS-1
Receiver (Front)
Fig. 03
12) LCD display
13) Control
Turn/press this control to select, adjust and
confirm the main menu options.
14) Return button
15) IR sensor
16) Power button
Press and hold down this button for 2 seconds to
switch the device on/off.
Receiver (Back)
Fig. 04
17) Power cable safety eye
18) Ground/lift switch
19) 3-pin XLR AF balanced OUT
20) BNC antenna A connector
21) Mic/line switch
22) AF connector OUT (6,3 mm jack)
23) 12–15 V DC power connector OUT
24) 12–15 V DC power connector IN
25) BNC antenna B connector
Installation
Remove all packing materials from the EDGE EBS-1. Check if all foam and plastic padding is removed.
Secure the equipment into a 19" rack if preferred. Connect the receiver to a power outlet with the
supplied DC power adaptor. Connect all cables. Insert the batteries into the transmitter.
Always disconnect from electric mains power supply before cleaning or servicing.
Damages caused by non-observance are not subject to warranty.
Mounting – Single Receiver
Fig. 05
Page 10
9
Order code: D1476B
EDGE EBS-1
Mounting – Multiple Receivers
Step 1
Fig. 06
Step 2
Fig. 07
Step 3
Fig. 08
Page 11
10
Order code: D1476B
EDGE EBS-1
Setup Examples
4 x EDGE EHS-1
Fig. 09
Page 12
11
Order code: D1476B
EDGE EBS-1
8 x EDGE EHS-1
Fig. 10
Page 13
12
Order code: D1476B
EDGE EBS-1
Setup and Operation
Follow the directions below, as they pertain to your preferred operation mode. Before using the device,
check the regulations regarding the frequency allocation in your country or region. Before plugging the
unit in, always make sure that the power supply matches the product specification voltage.
Receiver Setup
01) Connect the supplied power adapter to the DC power connector (24) on the rear of the receiver.
02) Plug the power adapter into a power outlet. Use only the supplied power adapter to connect the
device.
03) Press and hold down the power button (16) for 2 seconds to turn the device on.
04) Point the antennas (20/25) away from each other in a 45° position as shown in Fig. 11. Avoid placing
the receiver antennas near metal surfaces or other obstructions. Make sure the antennas do not
cross if stacking or rack-mounting receivers in a multiple-system setup.
Fig. 11
05) To connect the receiver to an amplifier either use an XLR to XLR cable, to connect via the receiver’s
3-pin XLR connector OUT (19), or a ¼” mono jack cable via the AF jack connector OUT (22).
06) Insert the batteries into the transmitter. See chapter: Inserting the Batteries, page 14.
07) Press and hold down the power button (03) for 2 seconds to turn the transmitter on.
08) Pair the transmitter with the receiver. See chapters 4. Scan and 5. Sync, page 18.
09) During use of the transmitter, the AF signal indicators will show the intensity of the incoming audio
signal.
10) Adjust the volume on the receiver and on the connected mixer or amplifier.
11) Mute the transmitter before turning it off, to prevent the occurrence of a popping sound.
12) Make sure you can always see a receiver antenna from the transmitter position. Keep the distance
from the transmitter to the receiver antenna as short as possible.
13) Perform a walk-through before performance or presentation to identify any dead spots. In case of
dead spots, adjust the location of the receiver. Should this not be sufficient, mark the dead spots in
order to avoid them.
Page 14
13
Order code: D1476B
EDGE EBS-1
Transmitter Setup
Install the beltpack on your belt by means of the belt clip (06).
Example 1 – Headset
Fig. 12
Example 2 – Electric Guitar
Fig. 13
Belt Clip Orientation
Fig. 14
For best performance and comfort, you can mount the belt clip in 2 different ways.
The best results can be reached with the antenna pointing upwards.
Page 15
14
Order code: D1476B
EDGE EBS-1
Control Panel
A) Antenna signal
B) AF signal mute
C) Receiver lock
D) Transmitter battery status
E) Group (A–J)
F) Channel (1–14)
G) Receiver frequency
H) Squelch
I) Device name
J) User color
K) High-pass filter status
L) AF signal strength
M) Wireless signal strength
Fig. 15
Inserting the Batteries
Fig. 16
01) Open the battery housing (10).
02) Insert the batteries into the battery housing (10). The transmitter operates with two AA 1,5 V batteries.
While inserting the batteries, mind the (+) and (-) symbols on the batteries and the housing.
03) Close the battery housing (10).
Page 16
15
Order code: D1476B
EDGE EBS-1
Compensation of Interference with Balanced Connections
Main Menu Options
01) Upon start-up, the display will show the DAP Audio logo. After 2 seconds, the display will show the
current device status.
02) Press the control (13) to open the main menu. The display will show:
03) Turn the control (13) to toggle through the following 14 menus:
● GROUP
● CHANNEL
● FREQ
● SCAN
Page 17
16
Order code: D1476B
EDGE EBS-1
● SYNC
● LOCK
● TX GAIN
● RX GAIN
● LOW CUT
● SQUELCH
● TONE KEY
● COLOR
● NAME
● ANT DC
04) Press the control (13) to open the desired menu.
1. Group
In this menu you can set the desired group. Each group (A–J) has a unique set of channels with 14 fixed
frequencies per channel. See the table on page 17.
01) Turn the control (13) until the display shows:
02) Press the control (13) to edit.
03) Turn the control (13) to select the desired group. The adjustment range is A–J.
04) Press the control (13) to save changes.
2. Channel
In this menu you can set the desired channel. Each channel (1–14) has a unique fixed frequency. See the
table on page 17.
01) Turn the control (13) until the display shows:
02) Press the control (13) to edit.
03) Turn the control (13) to select the desired channel. The adjustment range is 1–14.
04) Press the control (13) to save changes.
Page 18
17
Order code: D1476B
EDGE EBS-1
A B C D E
[1]:606.000MHz
[1]:606.200MHz
[1]:606.225MHz
[1]:606.300MHz
[1]:606.425MHz
[2]:608.025MHz
[2]:608.225MHz
[2]:607.250MHz
[2]:607.325MHz
[2]:607.450MHz
[3]:610.325MHz
[3]:610.525MHz
[3]:608.475MHz
[3]:608.550MHz
[3]:608.675MHz
[4]:612.900MHz
[4]:613.100MHz
[4]:609.925MHz
[4]:610.000MHz
[4]:610.125MHz
[5]:615.750MHz
[5]:615.950MHz
[5]:611.600MHz
[5]:611.675MHz
[5]:611.800MHz
[6]:618.875MHz
[6]:619.075MHz
[6]:614.050MHz
[6]:614.125MHz
[6]:614.250MHz
[7]:622.275MHz
[7]:622.475MHz
[7]:617.375MHz
[7]:617.450MHz
[7]:617.575MHz
[8]:626.050MHz
[8]:626.250MHz
[8]:620.275MHz
[8]:620.350MHz
[8]:620.475MHz
[9]:631.200MHz
[9]:631.400MHz
[9]:622.175MHz
[9]:622.250MHz
[9]:622.375MHz
[10]:639.475MHz
[10]:639.675MHz
[10]:626.750MHz
[10]:626.825MHz
[10]:626.950MHz
[11]:645.175MHz
[11]:645.375MHz
[11]:631.775MHz
[11]:631.850MHz
[11]:631.975MHz
[12]:653.175MHz
[12]:653.375MHz
[12]:638.775MHz
[12]:638.850MHz
[12]:638.975MHz
[13]:663.750MHz
[13]:663.950MHz
[13]:653.400MHz
[13]:653.475MHz
[13]:653.600MHz
[14]:667.800MHz
[14]:668.000MHz
[14]:661.750MHz
[14]:661.825MHz
[14]:661.950MHz
F G H I J
[1]:606.950MHz
[1]:607.000MHz
[1]:607.200MHz
[1]:607.225MHz
[1]:607.300MHz
[2]:607.975MHz
[2]:608.225MHz
[2]:608.300MHz
[2]:608.250MHz
[2]:608.625MHz
[3]:609.200MHz
[3]:609.250MHz
[3]:609.450MHz
[3]:609.700MHz
[3]:610.175MHz
[4]:610.650MHz
[4]:610.700MHz
[4]:610.900MHz
[4]:611.375MHz
[4]:611.950MHz
[5]:612.325MHz
[5]:612.375MHz
[5]:612.575MHz
[5]:614.075MHz
[5]:613.925MHz
[6]:614.775MHz
[6]:614.825MHz
[6]:615.025MHz
[6]:615.975MHz
[6]:617.000MHz
[7]:618.100MHz
[7]:618.150MHz
[7]:618.350MHz
[7]:621.125MHz
[7]:621.200MHz
[8]:621.000MHz
[8]:621.050MHz
[8]:621.250MHz
[8]:624.475MHz
[8]:623.400MHz
[9]:622.900MHz
[9]:622.950MHz
[9]:623.150MHz
[9]:628.400MHz
[9]:631.350MHz
[10]:627.475MHz
[10]:627.525MHz
[10]:627.725MHz
[10]:639.025MHz
[10]:633.975MHz
[11]:632.500MHz
[11]:632.550MHz
[11]:632.750MHz
[11]:643.825MHz
[11]:639.950MHz
[12]:639.500MHz
[12]:639.550MHz
[12]:639.750MHz
[12]:649.875MHz
[12]:646.975MHz
[13]:654.125MHz
[13]:654.175MHz
[13]:654.375MHz
[13]:655.475MHz
[13]:660.400MHz
[14]:662.475MHz
[14]:662.525MHz
[14]:662.725MHz
[14]:667.350MHz
[14]:664.800MHz
3. Freq
In this menu you can manually set the desired frequency.
01) Turn the control (13) until the display shows:
02) Press the control (13) to edit.
03) Turn the control (13) to select the desired frequency. The adjustment range is between 606–668 MHz.
04) Press the control (13) to save changes.
Page 19
18
Order code: D1476B
EDGE EBS-1
4. Scan
In this menu you can automatically scan the entire frequency range, in order to find and choose the
unused frequency. By doing so, you can avoid signal distortion.
01) Turn the control (13) until the display shows:
02) Press the control (13) to enter. The display will show:
03) The device will now automatically scan the entire frequency range (606–668 MHz). This process may
take up to 2 minutes.
04) Once the scanning is finished, turn the control (13) to select the desired frequency. Choose the least
used frequency in order to avoid signal distortion.
05) Press the control (13) to confirm.
5. Sync
In this menu you can pair the receiver with the transmitter.
01) Turn the control (13) until the display shows:
02) Press and hold down the power button (03) on the transmitter for 2 seconds to switch it ON.
03) Place the transmitter close to the receiver’s display (10–20 cm). Make sure that you point the IR
sensor (09) on the transmitter at the IR sensor (15) on the receiver.
04) Press the control (13) to pair the devices. The IR sensor (15) on the receiver will blink several times. The
devices are now paired and ready for use.
Page 20
19
Order code: D1476B
EDGE EBS-1
6. Lock
In this menu you can lock the receiver’s display.
01) Turn the control (13) until the display shows:
02) Press the control (13) to edit.
03) Turn the control (13) to select ON or OFF.
04) Press the control (13) to confirm.
05) If you have chosen ON, the display will be locked.
06) In order to unlock the display, press and hold down the control (13) for 4 seconds, until the receiver
lock symbol disappears (see C, Fig. 15, page 14).
7. Tx Gain
In this menu you can set the audio gain of the transmitter (input sensitivity).
01) Turn the control (13) until the display shows:
02) Press the control (13) to edit.
03) Turn the control (13) to set the desired gain. The adjustment range is from -32 dB to +4 dB.
04) Press the control (13) to save changes.
8. Rx Gain
In this menu you can set the output gain of the receiver.
01) Turn the control (13) until the display shows:
02) Press the control (13) to edit.
03) Turn the control (13) to set the desired gain. The adjustment range is from -32 dB to +4 dB.
04) Press the control (13) to save changes.
Page 21
20
Order code: D1476B
EDGE EBS-1
9. Low Cut
In this menu you can set the high-pass filter. The high-pass filter removes low frequency signals picked up
by the transmitter.
01) Turn the control (13) until the display shows:
02) Press the control (13) to edit.
03) Turn the control (13) to select ON or OFF.
04) Press the control (13) to confirm.
10. Squelch
In this menu you can set the squelch threshold. It eliminates the noise resulting from momentary spikes in
the output when turning the transmitter off. When too high in poor reception areas, it may compromise
the reception range. When too low, the noise may damage your hearing and/or the speakers.
01) Turn the control (13) until the display shows:
02) Press the control (13) to edit.
03) Turn the control (13) to set the value. The adjustment range is 1–10.
04) Press the control (13) to save changes.
11. Tone Key
In this menu you can set the tone key, by means of which the receiver can identify the presence of the
transmitter. The tone key also provides the battery status indication on the receiver.
01) Turn the control (13) until the display shows:
02) Press the control (13) to edit.
03) Turn the control (13) to select ON or OFF.
04) Press the control (13) to confirm.
Page 22
21
Order code: D1476B
EDGE EBS-1
12. Color
In this menu you can set the receiver’s color. It is useful when working with multiple receivers and
transmitters.
01) Turn the control (13) until the display shows:
02) Press the control (13) to edit.
03) Turn the control (13) to select one of the 8 colors (red, yellow, green, blue, orange, brown, white,
black).
04) Press the control (13) to confirm.
13. Name
In this menu you can set the receiver’s name. A name can consist of up to 8 characters.
01) Turn the control (13) until the display shows:
02) Press the control (13) to edit.
03) Turn the control (13) to choose the desired symbol for the first character.
04) Press the control (13) to confirm your choice and proceed to the following character. The currently
selected character will be highlighted.
05) Repeat steps 3–4 to edit the remaining characters.
Page 23
22
Order code: D1476B
EDGE EBS-1
14. Ant Dc
In this menu you can set the antenna input/output power supply.
01) Turn the control (13) until the display shows:
02) Press the control (13) to edit.
03) Turn the control (13) to select ON or OFF.
04) Press the control (13) to confirm.
● If the input power comes from the power adapter: the “ANT DC: On” will power the active antenna
via the BNC antenna connectors (20/25).
● If the input power comes from the antenna distributor: the “ANT DC: On” will power the receiver.
Note: When using the antenna distributor together with the power adapter, ANT DC must be set to “Off”
Page 24
23
Order code: D1476B
EDGE EBS-1
Transmitter
01) Press and hold down the power button (03) for 2 seconds to switch the transmitter ON/OFF.
02) Upon start-up, the display will show the following splash screen:
Mute
01) Move the mute switch (07) to ON, to mute the transmitter.
02) Move the mute switch (07) to MUTE, to deactivate mute.
Lock
01) Move the lock switch (11) to LOCK, to lock the transmitter. When the lock is on, it is not possible to
adjust the device’s settings.
02) Move the lock switch (11) to UNLOCK, to unlock the transmitter.
Main Menu Options
01) Press the power button (03) to open the main menu. The display will show:
02) Press the UP/DOWN buttons (04/05) to select the desired frequency. The adjustment range is
between 606–666 MHz.
03) Press the power button (03) to save changes. The display will show:
04) Press the UP/DOWN buttons (04/05) to set the desired gain. The adjustment range is from -32 dB to
+4 dB.
Page 25
24
Order code: D1476B
EDGE EBS-1
05) Press the power button (03) to save changes. The display will show:
06) Press the UP/DOWN buttons (04/05) to set the desired RF power. Select one of the 3 options:
● LOW (10 mW)
● MID (20 mW)
● HIGH (30 mW)
07) Press the power button (03) to save changes. The display will now show the splash screen.
Note: The maximum allowed RF output is 10 mW. The use of outputs stronger than 10 mW must be
permitted by the local authorities.
Page 26
25
Order code: D1476B
EDGE EBS-1
Connection Cables
Take care of your cables, always holding them by the connectors and avoiding knots and twists when
coiling them: This gives the advantage of increasing their life and reliability. Periodically check your
cables. A great number of problems (faulty contacts, ground hum, discharges, etc.) are caused entirely
by using unsuitable or faulty cables.
Unbalanced
Balanced
Headphones
Insert
For these applications the unit provides 1/4” TRS and XLR connectors to easily interface with most
professional audio devices. Follow the configuration examples below for your particular connection.
Page 27
26
Order code: D1476B
EDGE EBS-1
Maintenance
The DAP Audio EDGE EBS-1 requires almost no maintenance. However, you should keep the unit clean.
Disconnect the mains power supply, and then wipe the cover with a damp cloth. Do not immerse in
liquid. Do not use alcohol or solvents.
Keep connections clean. Disconnect electric power, and then wipe the audio connections with a damp
cloth. Make sure connections are thoroughly dry before linking equipment or supplying electric power.
Troubleshooting
DAP Audio EDGE EBS-1
This troubleshooting guide is meant to help solve simple problems. If you are unable to determine the
cause of the problem, do not open the unit, as this may damage the device and the warranty will be
deemed void. Return the device to your DAP Audio dealer.
Problem
Solution
No sound
● Make sure the transmitter is on.
● Make sure the batteries are inserted properly. If the
batteries are inserted properly, replace them with a set of
new batteries.
● Make sure the battery housing is clean.
No sound
● Make sure the DC power adapter is plugged into the
appropriate power outlet and into the DC power connector
IN (24) on the receiver. Make sure the AC electrical output
works and supplies proper voltage.
No sound
● Turn up the volume on the receiver and/or the transmitter
and/or the speaker.
● Make sure the output connections between the receiver
and external equipment are in order.
No sound
● Make sure that the transmitter and the receiver use the
same frequency.
● Move the transmitter closer to the receiver.
Bursts of noise or other audible signals
present
● Adjust the squelch threshold.
● Identify potential sources of interference (other RF sources)
and turn them off.
Momentary loss of sound as
transmitter is moved around the
performance area.
● Reposition the receiver and perform a walk-through test
again. If audible drop-outs persist, mark the dead spots and
avoid them during performance.
Bad reception
● Check the antennas.
Page 28
27
Order code: D1476B
EDGE EBS-1
Approval
The DAP Audio EDGE EBS-1 is a Class 2 wireless audio device (Commission Decision 2000/299/EC).
Frequency range: 606–668 MHz
BE
BG
CZ
DK
DE
EE
IE
EL
ES
FR
HR
IT
CY
LV
LT
LU
HU
MT
NL
AT
PL
PT
RO
SI
SK
FI
SE
UK
Exclusion of liability
The frequency ranges available for wireless microphones differ per country and region. Consult the
respective national and/or regional authorities as licensing or specific restrictions may apply for the use of
the device. We do not take any responsibility in case the device cannot operate or be used in your
country/region or if it requires additional licensing. Before using the device, check the allowed
frequencies in your country or region.
Be aware that in some countries you are allowed to partly use the frequency range of the device. Consult
your local authorities for the latest information and regulations.
Spectrum authorities in the EU countries:
Belgium
Belgian Institute for Postal Services and
Communications
www.bipt.be
Bulgaria
Communications Regulation Commission
www.crc.bg
Czech Republic
Czech Telecommunication Office
www.ctu.cz
Denmark
Danish Energy Agency
www.ens.dk
Germany
Die Bundesnetzagentur
www.bundesnetzagentur.de
Estonia
Technical Regulatory Authority
www.tja.ee
Ireland
Commission for Communications Regulation
www.comreg.ie
Greece
Hellenic Telecommunications and Post Commission
www.eett.gr
Spain
Secretaría de Estado para el Avance Digital
www.mineco.gob.es
France
Agence Nationale des Fréquences
www.anfr.fr
Croatia
Regulatory Authority for Network Industries
www.hakom.hr
Italy
Istituto Superiore delle Comunicazioni e delle
Tecnologie dell’Informazione
www.isticom.it
Cyprus
Department of Electronic Communications
www.mcw.gov.cy
Latvia
Electronic Communications Office
www.vases.lv
Lithuania
Communications Regulatory Authority
www.rrt.lt
Luxembourg
Institut Luxembourgeois de Régulation
www.ilr.lu
Hungary
National Communications Authority
www.nmhh.hu
Malta
Malta Communications Authority
www.mca.org.mt
Netherlands
Agentschap Telecom
www.agentschaptelecom.nl
Austria
Rundfunk und Telekom Regulierungs-GmbH
www.rtr.at
Poland
Office of Electronic Communications
www.uke.gov.pl
Portugal
Autoridade Nacional de Comunicações
www.anacom.pt
Romania
National Authority for Management and Regulation
in Communications
www.ancom.org.ro
Slovenia
Agency for Communication Networks and Services
www.akos-rs.si
Slovakia
Regulatory Authority for Electronic Communications
and Postal Services
www.teleoff.gov.sk
Finland
Finnish Transport and Communications Agency
www.traficom.fi
Sweden
Post and Telecom Authority
www.pts.se
United Kingdom
Office of Communications
www.ofcom.org.uk
Page 29
28
Order code: D1476B
EDGE EBS-1
Spectrum authorities in the EFTA countries:
Iceland
Post and Telecom Administration
www.pfs.is
Liechtenstein
Amt für Kommunikation
www.llv.li
Norway
Norwegian Communications Authority
www.nkom.no
Switzerland
Federal Office of Communications
www.bakom.admin.ch
Spectrum authorities in the EU candidate countries:
Montenegro
Agency for Electronic Communications and Postal
Services
www.ekip.me
Republic of North
Macedonia
Agency for Electronic Communications
www.aek.mk
Albania
Electronic and Postal Communications Authority
www.akep.al
Serbia
Regulatory Agency for Electronic Communications
and Postal Services
www.ratel.rs
Turkey
Information and Communications Technologies
Authority
www.btk.gov.tr
Product Specifications
Model:
DAP Audio EDGE EBS-1
Power supply:
DC 12–15 V, 300 mA
Dimensions (transmitter):
63 x 21 x 215 mm (LxWxH)
Dimensions (receiver):
205 x 170 x 263 mm (LxWxH)
Weight (transmitter):
0,18 kg
Weight (receiver):
1,24 kg
Receiver:
Modulation:
FM
Frequency range:
606–668 MHz
Frequency response:
75 Hz–18 kHz
Sensitivity:
-100 dBm/30 dB sinad
Distortion:
<1%(AF1 kHz, RF46 dBu)
Max SPL:
128 dB SPL
RF stability:
≤ ± 15 ppm
Frequency deviation:
± 75 kHz
Spurious rejection:
>50 dB
SNR:
>100 dBA
Transmission latency:
0 ms
Audio outputs:
3-pin XLR OUT balanced, mono ¼” jack unbalanced
Pilot frequency:
32768 kHz
Output signal sensitivity adjustable range:
48 dB, Adopt 6 dB step for adjustment
Indicators:
A/B antenna, AF signal
Transmitter:
Input:
3-pin mini XLR
Input impedance:
1 mΩ
Output gain range:
30 dB
RF output:
10 mW/20 mW/30 mW
Power supply:
2 x AA 1,5 V batteries (not included)
Max. ambient temperature ta:
40 °C
Max. housing temperature tB:
70 °C
Design and product specifications are subject to change without prior notice.
Website: www.Dap-audio.info
Email: service@highlite.com
Page 30
29
Order code: D1476B
EDGE EBS-1
Dimensions
Page 31
30
Order code: D1476B
EDGE EBS-1
Page 32
©2020 DAP Audio
Loading...