Dantherm CDT 30, CDT 30 S, CDT 40, CDT 40 S, CDT 60 Datasheet

MOBILE DEHUMIDIFIERS CDT

CDT 30

CDT 30
MOBILE DEHUMIDIFIER

Function

The CDT 30 is a robust, cost-effective and energy-efficient, reliable mobile de­humidifier. It works in accordance with the condensation principle. A fan draws
the humid air into the dehumidifier and through an evaporator coil. When
passing through the evaporator the air is cooled down to below its dew point
temperature, and its content of water vapour is condensed into water, which is
collected in the water container.

Applications

• Damage service

• Building drying

• Water works

• Dry storing

FEATURES

Dehumidier

• High capacity

• Low energy consumption

• Strong and robust cabinet of powder coated hot galvanized steel

• Epoxy coated evaporator and condenser.

• Adjustable handle

• Plastic bumpers

• Low weight

• Stackable.

• Large wheels

Digital touchpad control panel:

1. On-o switch

2. Reading of room temperature

3. Indicator for normal operation (green lamp)

4. Reading of RH value / setting of RH value

5. Indicator for full water container (yellow lamp)

6. Failure indicator (red lamp)

7. Hour counter / setting of service intervals

8. kWh counter

Water container

• Water container with handles

• Automatic stop when water container is full or removed.

• Permanent drainage can be established with optional ½” hose connection

• Condensate pump in a cassette as optional extra

Electronic control

• Digital touchpad control panel with display

• Accurate hour and kWh counter (reading)

• RH and °C monitoring (reading)

• RH setting

• Easy fault-finding

• Service monitoring function

Defrosting

Active, demand-controlled defrosting which is activated through a tempera­ture sensor on the evaporator. Defrosting is done by means of hot refrigerant
being fed through the evaporator.

MOBILE DEHUMIDIFIERS CDT

740

650

Sheetmetal flatstate is based on Dantherm A/S process equipment and is
only entended as a guide.

table LZT 142 0001, category

ohr

Material must comply to Directive 2002/95/EC of the European Parliament. (RoHS)

65610.26g

3
5
1
1
8
9

MATERIAL:

THICKNESS:

WEIGHT:

REV. BY:

DATE:

REF.:

8

Surface appearance according to reference

BEND RADII:

Material must comply to Regulation (EC) No 1907/2006 of the European parliament. (REACH)

CDT 30 MK II

P
A
R
T
N
O

THIS DRAWING IS FURNISHED WITH THE
UNDERSTANDING THAT THE ESSENCE
THERE OF WILL NOT BE REPRODUCED
IN W

HOLE OR IN PART WITHOUT

Linear dimensions without tolerances according to DS/EN 22768-1 medium
Angular dimensions without tolerances: ± 1°

740

650

427

10

15

20

25

30

35

°C

L/H

TECHNICAL DATA

Model CDT 30

Operating range – humidity 40-100% RH
Operating range – temperature 3-32°C
Air volume 250 m³/h
Power supply 230 V/50 Hz
Max. ampere consumption 2,7 A
Max. power consumption 0,590 kW
Refrigerant R 134a
Compressor type Rotary
Sound level (at 1 metre) 56 dB(A)
Water container capacity 7 litres
Colour - water container and wheel cap RAL 7015
Colour - front grille RAL 7044
Colour - control panel and bumpers RAL 9005
Protection class IP X4
Filter PPI 15/G1
Wheel size Ø 250 mm
Wheel and water container material PP
Control panel material ABS
Weight 32 kg

CAPACITY CURVES

40%

60%

5

0

0 0,2 0,4 0,6 0,8 1,0 1,2 1,4 1,6

80%

Specic energy consumption (SEC)

• 0,45 kWh/l at 30°C & 80% RH

• 0,81 kWh/l at 20°C & 60% RH

Accessories

½” drain outlet
Remote hygrostat
Wall bracket
Dual voltage kit
Condensate pump in a cassette
(see separate data sheet)

Also available in this series:

CDT 30 S
CDT 40
CDT 40 S
CDT 60
CDT 90
(see separate data sheets)

DIMENSIONS

426

427

736

740

650

650

506

All dimensions are in mm.

dantherm.com

MOBILE DEHUMIDIFIERS CDT

CDT 30 S

CDT 30 S
MOBILE DEHUMIDIFIER

Function

The CDT 30 S is a robust, cost-effective and energy-efficient, reliable mobile de­humidifier. It works in accordance with the condensation principle. A fan draws
the humid air into the dehumidifier and through an evaporator coil. When
passing through the evaporator the air is cooled down to below its dew point
temperature, and its content of water vapour is condensed into water, which is
collected in the water container.

Applications

• Damage service

• Building drying

• Water works

• Dry storing

FEATURES

Dehumidier

• High capacity

• Low energy consumption

• Strong and robust cabinet of powder coated hot galvanized steel

• Epoxy coated evaporator and condenser.

• Adjustable handle

• Plastic bumpers

• Low weight

• Stackable.

• Large wheels

• On the back two Ø100 mm flex. air ducts may be connected

(max. length of 5 m) (accessory)

• Built-in 1 kW heating element

• Supplied with high pressure fan

Digital touchpad control panel:

1. On-o switch

2. Reading of room temperature

3. Indicator for normal operation (green lamp)

4. Reading of RH value / setting of RH value

5. Indicator for full water container (yellow lamp)

6. Failure indicator (red lamp)

7. Hour counter / setting of service intervals

8. kWh counter

Water container

• Water container with handles

• Automatic stop when water container is full or removed.

• Permanent drainage can be established with optional ½” hose connection

• Condensate pump in a cassette as optional extra

Electronic control

• Digital touchpad control panel with display

• Accurate hour and kWh counter (reading)

• RH and °C monitoring (reading)

• RH setting

• Easy fault-finding

• Service monitoring function

Defrosting

Active, demand-controlled defrosting which is activated through a tempera­ture sensor on the evaporator. Defrosting is done by means of hot refrigerant
being fed through the evaporator.

MOBILE DEHUMIDIFIERS CDT

750

650

750

CDT 30 S MK II

64278.09g

BEND RADII:

24-05-2012

ohr

MATERIAL:

THICKNESS:

WEIGHT:

REV. BY:

DATE:

REF.:

DATE:

R

P
A
R
T
N
O

Material must comply to Regulation (EC) No 1907/2006 of the European parliament. (REACH)

Material must comply to Directive 2002/95/EC of the European Parliament. (RoHS)

3
5
1
1
9
0

only entended as a guide.

8

Sheetmetal flatstate is based on Dantherm A/S process equipment and is

table LZT 142 0001, category

Surface appearance according to reference

ARE THE PROPERTY OF SAID COMPANY

THIS DRAWING IS FURNISHED WITH THE
UNDERSTANDING THAT THE ESSENCE
THERE OF WILL NOT BE REPRODUCED
IN WHOLE OR IN PART WITHOUT
WRITTEN AUTHORIZATION BY Dantherm A/S.
ALL DESIGNS ORIGINATED BY Dantherm A/S

Linear dimensions without tolerances according to DS/EN 22768-1 medium
Angular dimensions without tolerances: ± 1°

750

650

426

10

15

20

25

30

35

°C

L/H

40%

60%

80%

TECHNICAL DATA

Model CDT 30 S

Operating range – humidity 40-100% RH
Operating range – temperature 3-32°C
Air volume 350 m³/h*
Power supply 230 V/50 Hz
Max. ampere consumption 2,6 A
Max. power consumption with heating element 1,56 kW
Max. power consumption without heating element 0,56 kW
Refrigerant R 134a
Compressor type Rotary
Sound level (at 1 metre) 60 dB(A)**
Water container capacity 7 litres
Colour - water container and wheel cap RAL 7015
Colour - front grille RAL 7044
Colour - control panel and bumpers RAL 9005
Protection class IP X4
Filter PPI 15/G1
Wheel size Ø 250 mm
Wheel and water container material PP
Control panel material ABS
Weight 34 kg

*Measured without air ducts mounted.
**Measured with air ducts mounted.

Accessories

½” drain outlet
Remote hygrostat
Wall bracket
Dual voltage kit
Condensate pump in a cassette
Flex. air ducts Ø100 mm
(see separate data sheet)

CAPACITY CURVES

5

0

0 0,2 0,4 0,6 0,8 1,0 1,2 1,4 1,6

Specic energy consumption (SEC)

• 0,39 kWh/l at 30°C & 80% RH

• 0,76 kWh/l at 20°C & 60% RH

DIMENSIONS

Also available in this series:

CDT 30
CDT 40
CDT 40 S
CDT 60
CDT 90
(see separate data sheets)

426

736

650

650

506

All dimensions are in mm.

dantherm.com

MOBILE DEHUMIDIFIERS CDT

CDT 40

CDT 40
MOBILE DEHUMIDIFIER

Function

The CDT 40 is a robust, cost-effective and energy-efficient, reliable mobile de­humidifier. It works in accordance with the condensation principle. A fan draws
the humid air into the dehumidifier and through an evaporator coil. When
passing through the evaporator the air is cooled down to below its dew point
temperature, and its content of water vapour is condensed into water, which is
collected in the water container.

Applications

• Damage service

• Building drying

• Water works

• Dry storing

FEATURES

Dehumidier

• High capacity

• Low energy consumption

• Strong and robust cabinet of powder coated hot galvanized steel

• Epoxy coated evaporator and condenser.

• Adjustable handle

• Plastic bumpers

• Low weight

• Stackable.

• Large wheels

Digital touchpad control panel:

1. On-o switch

2. Reading of room temperature

3. Indicator for normal operation (green lamp)

4. Reading of RH value / setting of RH value

5. Indicator for full water container (yellow lamp)

6. Failure indicator (red lamp)

7. Hour counter / setting of service intervals

8. kWh counter

Water container

• Water container with handles

• Automatic stop when water container is full or removed.

• Permanent drainage can be established with optional ½” hose connection

• Condensate pump in a cassette as optional extra

Electronic control

• Digital touchpad control panel with display

• Accurate hour and kWh counter (reading)

• RH and °C monitoring (reading)

• RH setting

• Easy fault-finding

• Service monitoring function

Defrosting

Active, demand-controlled defrosting which is activated through a tempera­ture sensor on the evaporator. Defrosting is done by means of hot refrigerant
being fed through the evaporator.

MOBILE DEHUMIDIFIERS CDT

740

825

Material must comply to Directive 2002/95/EC of the European Parliament. (RoHS)

ohr

93699.24g

BEND RADII:

24-05-2012

MATERIAL:

THICKNESS:

WEIGHT:

REV. BY:

DATE:

REF.:

DATE:

P
A
R
T
N
O

Material must comply to Regulation (EC) No 1907/2006 of the European parliament. (REACH)

3
5
1
1
9
1

only entended as a guide.

CDT 40 MK II

8

Sheetmetal flatstate is based on Dantherm A/S process equipment and is

table LZT 142 0001, category

Surface appearance according to reference

THIS DRAWING IS FURNISHED WITH THE
UNDERSTANDING THAT THE ESSENCE
THERE OF WILL NOT BE REPRODUCED
IN WHO

LE OR IN PART WITHOUT
WRITTEN AUTHORIZATION BY Dantherm A/S.
ALL DESIGNS ORIGINATED BY Dantherm A/S

Linear dimensions without tolerances according to DS/EN 22768-1 medium
Angular dimensions without tolerances: ± 1°

740

825

545

10

15

20

25

30

35

°C

H

0 0,2 0,4 0,6 0,8 1,0 1,2 1,4 1,6 1,8

TECHNICAL DATA

Model CDT 40

Operating range – humidity 40-100% RH
Operating range – temperature 3-32°C
Air volume 350 m³/h
Power supply 230 V/50 Hz
Max. ampere consumption 3,6 A
Max. power consumption 0,82 kW
Refrigerant R 407C
Compressor type Rotary
Sound level (at 1 metre) 59 dB(A)
Water container capacity 14 litres
Colour - water container and wheel cap RAL 7015
Colour - front grille RAL 7044
Colour - control panel and bumpers RAL 9005
Protection class IP X4
Filter PPI 15/G1
Wheel size Ø 250 mm
Wheel and water container material PP
Control panel material ABS
Weight 43 kg

CAPACITY CURVES

5

0

Specic energy consumption (SEC)

• 0,50 kWh/l at 30°C & 80% RH

• 0,66 kWh/l at 20°C & 60% RH

Accessories

½” drain outlet
Remote hygrostat
Wall bracket
Dual voltage kit
Condensate pump in a cassette
(see separate data sheet)

Also available in this series:

CDT 30
CDT 30 S
CDT 40 S
CDT 60
CDT 90
(see separate data sheets)

DIMENSIONS

542

545

dantherm.com

40%

60%

80%

L/

823

736

825

740

539

540

All dimensions are in mm.

MOBILE DEHUMIDIFIERS CDT

CDT 40 S

CDT 40 S
MOBILE DEHUMIDIFIER

Function

The CDT 40 S is a robust, cost-effective and energy-efficient, reliable mobile de­humidifier. It works in accordance with the condensation principle. A fan draws
the humid air into the dehumidifier and through an evaporator coil. When
passing through the evaporator the air is cooled down to below its dew point
temperature, and its content of water vapour is condensed into water, which is
collected in the water container.

Applications

• Damage service

• Building drying

• Water works

• Dry storing

FEATURES

Dehumidier

• High capacity

• Low energy consumption

• Strong and robust cabinet of powder coated hot galvanized steel

• Epoxy coated evaporator and condenser.

• Adjustable handle

• Plastic bumpers

• Low weight

• Stackable.

• Large wheels

• On the back two Ø100 mm flex. air ducts may be connected

(max. length of 5 m) (accessory)

• Built-in 1 kW heating element

• Supplied with high pressure fan

Digital touchpad control panel:

1. On-o switch

2. Reading of room temperature

3. Indicator for normal operation (green lamp)

4. Reading of RH value / setting of RH value

5. Indicator for full water container (yellow lamp)

6. Failure indicator (red lamp)

7. Hour counter / setting of service intervals

8. kWh counter

Water container

• Water container with handles

• Automatic stop when water container is full or removed.

• Permanent drainage can be established with optional ½” hose connection

• Condensate pump in a cassette as optional extra

Electronic control

• Digital touchpad control panel with display

• Accurate hour and kWh counter (reading)

• RH and °C monitoring (reading)

• RH setting

• Easy fault-finding

• Service monitoring function

Defrosting

Active, demand-controlled defrosting which is activated through a tempera­ture sensor on the evaporator. Defrosting is done by means of hot refrigerant
being fed through the evaporator.

MOBILE DEHUMIDIFIERS CDT

740

825

Material must comply to Directive 2002/95/EC of the European Parliament. (RoHS)

ohr

93418.55g

BEND RADII:

24-05-2012

MATERIAL:

THICKNESS:

WEIGHT:

REV. BY:

DATE:

REF.:

DATE:

P
A
R
T
N
O

Material must comply to Regulation (EC) No 1907/2006 of the European parliament. (REACH)

3
5
1
1
9
2

only entended as a guide.

CDT 40 S MK II

8

Sheetmetal flatstate is based on Dantherm A/S process equipment and is

table LZT 142 0001, category

Surface appearance according to reference

THIS DRAWING IS FURNISHED WITH THE
UNDERSTANDING THAT THE ESSENCE
THERE OF WILL NOT BE REPRODUCED
IN WHOLE OR IN PART WITHOUT
WRITTEN AUTHORIZATION BY Dantherm A/S.
ALL DESIGNS ORIGINATED BY Dantherm A/S

Linear dimensions without tolerances according to DS/EN 22768-1 medium
Angular dimensions without tolerances: ± 1°

740

825

542

10

15

20

25

30

35

°C

L/H

40%

60%

80%

TECHNICAL DATA

Model CDT 40 S

Operating range – humidity 40-100% RH
Operating range – temperature 3-32°C
Air volume 560 m³/h*
Power supply 230 V/50 Hz
Max. ampere consumption 3,7 A
Max. power consumption with heating element 1,83 kW
Max. power consumption without heating element 0,83 kW
Refrigerant R 407c
Compressor type Rotary
Sound level (at 1 metre) 62 dB(A)**
Water container capacity 14 litres
Colour - water container and wheel cap RAL 7015
Colour - front grille RAL 7044
Colour - control panel and bumpers RAL 9005
Protection class IP X4
Filter PPI 15/G1
Wheel size Ø 250 mm
Wheel and water container material PP
Control panel material ABS
Weight 46 kg

*Measured without air ducts mounted.
**Measured with air ducts mounted.

CAPACITY CURVES

5

0

0 0,2 0,4 0,6 0,8 1,0 1,2 1,4 1,6 1,8 2,0

Specic energy consumption (SEC)

• 0,47 kWh/l at 30°C & 80% RH

• 0,83 kWh/l at 20°C & 60% RH

Accessories

½” drain outlet
Remote hygrostat

DIMENSIONS

Wall bracket
Dual voltage kit
Condensate pump in a cassette
Flex. air ducts Ø100 mm
(see separate data sheet)

Also available in this series:

CDT 30
CDT 30 S
CDT 40
CDT 60
CDT 90
(see separate data sheets)

542

823

825

736

740

All dimensions are in mm.

539

540

dantherm.com

MOBILE DEHUMIDIFIERS CDT

CDT 60

CDT 60
MOBILE DEHUMIDIFIER

Function

The CDT 60 is a robust, cost-effective and energy-efficient, reliable mobile de­humidifier. It works in accordance with the condensation principle. A fan draws
the humid air into the dehumidifier and through an evaporator coil. When
passing through the evaporator the air is cooled down to below its dew point
temperature, and its content of water vapour is condensed into water, which is
collected in the water container.

Applications

• Damage service

• Building drying

• Water works

• Dry storing

FEATURES

Dehumidier

• High capacity

• Low energy consumption

• Strong and robust cabinet of powder coated hot galvanized steel

• Epoxy coated evaporator and condenser.

• Adjustable handle

• Plastic bumpers

• Low weight

• Stackable.

• Large wheels

Digital touchpad control panel:

1. On-o switch

2. Reading of room temperature

3. Indicator for normal operation (green lamp)

4. Reading of RH value / setting of RH value

5. Indicator for full water container (yellow lamp)

6. Failure indicator (red lamp)

7. Hour counter / setting of service intervals

8. kWh counter

Water container

• Water container with handles

• Automatic stop when water container is full or removed.

• Permanent drainage can be established with optional ½” hose connection

• Condensate pump in a cassette as optional extra

Electronic control

• Digital touchpad control panel with display

• Accurate hour and kWh counter (reading)

• RH and °C monitoring (reading)

• RH setting

• Easy fault-finding

• Service monitoring function

Defrosting

Active, demand-controlled defrosting which is activated through a tempera­ture sensor on the evaporator. Defrosting is done by means of hot refrigerant
being fed through the evaporator.

MOBILE DEHUMIDIFIERS CDT

820

905

Material must comply to Directive 2002/95/EC of the European Parliament. (RoHS)

only entended as a guide.

CDT 60 MK II

99141.12g

BEND RADII:

ohr

MATERIAL:

THICKNESS:

WEIGHT:

REV. BY:

DATE:

REF.:

DATE:

P
A
R
T
N
O

Material must comply to Regulation (EC) No 1907/2006 of the European parliament. (REACH)

25-05-2012

3
5
1
1
9
3

8

Sheetmetal flatstate is based on Dantherm A/S process equipment and is

table LZT 142 0001, category

Surface appearance according to reference

THIS DRAWING IS FURNISHED WITH THE
UNDERSTANDING THAT THE ESSENCE
THERE OF WILL NOT BE REPRODUCED
IN WHOLE OR IN PART WITHOUT
WRITTEN AUTHORIZATION BY Dantherm A/S.

Linear dimensions without tolerances according to DS/EN 22768-1 medium
Angular dimensions without tolerances: ± 1°

820

905

542

10

15

20

25

30

35

°C

H

80%

TECHNICAL DATA

Model CDT 60

Operating range – humidity 40-100% RH
Operating range – temperature 3-32°C
Air volume 725 m³/h
Power supply 230 V/50 Hz
Max. ampere consumption 4,9 A
Max. power consumption 1,12 kW
Refrigerant R 407c
Compressor type Rotary
Sound level (at 1 metre) 62 dB(A)
Water container capacity 14 litres
Colour - water container and wheel cap RAL 7015
Colour - front grille RAL 7044
Colour - control panel and bumpers RAL 9005
Protection class IP X4
Filter PPI 15/G1
Wheel size Ø 250 mm
Wheel and water container material PP
Control panel material ABS
Weight 47 kg

CAPACITY CURVES

40%

5

0

0 0,5 1,0 1,5 2,0 2,5 3,0

60%

L/

Specic energy consumption (SEC)

• 0,43 kWh/l at 30°C & 80% RH

• 0,67 kWh/l at 20°C & 60% RH

Accessories

½” drain outlet
Remote hygrostat

DIMENSIONS

Wall bracket
Dual voltage kit
Condensate pump in a cassette
(see separate data sheet)

542

903

905

816

820

All dimensions are in mm.

539

540

Also available in this series:

CDT 30
CDT 30 S
CDT 40
CDT 40 S
CDT 90
(see separate data sheets)

dantherm.com

MOBILE DEHUMIDIFIERS CDT

CDT 90

CDT 90
MOBILE DEHUMIDIFIER

Function

The CDT 90 is a robust, cost-effective and energy-efficient, reliable mobile de­humidifier. It works in accordance with the condensation principle. A fan draws
the humid air into the dehumidifier and through an evaporator coil. When
passing through the evaporator the air is cooled down to below its dew point
temperature, and its content of water vapour is condensed into water, which
falls into the drip tray and then is led to the drain.

Applications

• Damage service

• Building drying

• Water works

• Dry storing

FEATURES

Dehumidier

• High capacity

• Low energy consumption

• Strong and robust cabinet of powder coated hot galvanized steel

• Epoxy coated evaporator and condenser.

• Adjustable handle

• Plastic bumpers

• Low weight

• Large wheels

Digital touchpad control panel:

1. On-o switch

2. Reading of room temperature

3. Indicator for normal operation (green lamp)

4. Reading of RH value / setting of RH value

5. Indicator for full water container (yellow lamp)

6. Failure indicator (red lamp)

7. Hour counter / setting of service intervals

8. kWh counter

Water drain

• Fitted with a drain outlet for connection to a ½” water hose

Electronic control

• Digital touchpad control panel with display

• Accurate hour and kWh counter (reading)

• RH and °C monitoring (reading)

• RH setting

• Easy fault-finding

• Service monitoring function

Defrosting

Active, demand-controlled defrosting which is activated through a tempera­ture sensor on the evaporator. Defrosting is done by means of hot refrigerant
being fed through the evaporator.

MOBILE DEHUMIDIFIERS CDT

895

980

ohr

Material must comply to Directive 2002/95/EC of the European Parliament. (RoHS)

355066.95g

BEND RADII:

23-12-2011

MATERIAL:

THICKNESS:

WEIGHT:

REV. BY:

DATE:

REF.:

DATE:

R
E

P
A
R
T
N
O

Material must comply to Regulation (EC) No 1907/2006 of the European parliament. (REACH)

3
5
1
1
9
4

only entended as a guide.

CDT 90 MK II

8

Sheetmetal flatstate is based on Dantherm A/S process equipment and is

table LZT 142 0001, category

Surface appearance according to reference

ARE THE PROPERTY OF SAID COMPANY

THIS DRAWING IS FURNISHED WITH THE
UNDERSTANDING THAT THE ESSENCE
THERE OF WILL NOT BE REPRODUCED
IN W

HOLE OR IN PART WITHOUT
WRITTEN AUTHORIZATION BY Dantherm A/S.
ALL DESIGNS ORIGINATED BY Dantherm A/S

Linear dimensions without tolerances according to DS/EN 22768-1 medium
Angular dimensions without tolerances: ± 1°

895

980

650

10

15

20

25

30

35

°C

L/H

0 0,5 1,0 1,5 2,0 2,5 3,0 3,5 4,0 4,5

TECHNICAL DATA

Model CDT 90

Operating range – humidity 40-100% RH
Operating range – temperature 3-32°C
Air volume 1000 m³/h
Power supply 230 V/50 Hz
Max. ampere consumption 7,2 A
Max. power consumption 1,64 kW
Refrigerant R 407c
Compressor type Rotary
Sound level (at 1 metre) 62 dB(A)
Colour - wheel cap RAL 7015
Colour - front grill RAL 7044
Colour - control panel and bumpers RAL 9005
Protection class IP X4
Filter PPI 15/G1
Wheel size Ø 250 mm
Wheel material PP
Control panel material ABS
Weight 62 kg

CAPACITY CURVES

5

0

Specic energy consumption (SEC)

• 0,42 kWh/l at 30°C & 80% RH

• 0,71 kWh/l at 20°C & 60% RH

DIMENSIONS

Accessories

Remote hygrostat
Dual voltage kit
(see separate data sheet)

Also available in this series:

CDT 30
CDT 30 S
CDT 40
CDT 40 S
CDT 60
(see separate data sheets)

650

dantherm.com

977

980

894

895

40%

60%

All dimensions are in mm.

80%

593

593

MOBILE DEHUMIDIFIERS CDT

ACCESSORIES CDT

Illustration Accessory Description CDT-type

Hygrostat When a hygrostat is connected the dehumidifier

can operate continuously dependent on the rela­tive humidity in the room.

Two versions are available:

½” draining tap and
screwed hose con-

Hygrostat with 0,4 m cable, jack plug and fitting

Hygrostat with 3 m cable and jack plug

Ball tap, brass screwed hose connector and clamp
for mounting on the water container

All

All

All 396243

nector

Condensate pump in a
cassette

Cassette with builtin condensate pump CDT

30/30S

Dantherm
No.

396242

396241

075616

Wall bracket Using the wall bracket the dehumidifier can be

hung on the wall

Flexible air duct Ø100
mm with clamp

CDT 30S and CDT 40S are prepared for connection
of two flexible air ducts

CDT 40/
40S/60

CDT
30/30S

CDT 40/
40S/60

CDT 30S/
CDT 40S

075617

396247

396248

80100065

(clamp:

543620)

dantherm.com